Search Documents

By A. Fiszer

One of the major problems with deep Polish hard coal mines are deformations of close-to-wall galleries since they are necessary and must he kept open for emergency situations and are largely responsible for work disturbances. In order to ensure safe and effective working operations, it is necessary to often rebuild galleries which, apart from the inevitable stoppage of operations, is greatly disadvantageous for the operation of a mine. The largest problems with maintaining the galleries open occur in Lower Silesian Coal Field mines where sometimes it is necessary to reconstruct the galleries several times [(Fig. 1)]. In light of what has been said above, the aim of this article is to present the reader with methods and ways of determining deformations occurring in close-to-wall galleries. Squeezing or convergence of headings is only a portion of the entire process of ground movement caused by ground disturbance due to workings. The term "squeezing of headings" is to be understood as a shortening of the distance between a point set on the roof of a heading and the corresponding one on the floor. It is very important to know the rules governing the process of squeezing in a particular mining system since it affords possibilities to define changes of the process and its parameters at any moment for a given system. This is of utmost importance because convergence of a heading is one of the most significant manifestations of ground pressure which has already been proved by studies performed by Everling (1). On the basis of those studies it has been observed that there exists an almost linear relation between the rate of convergence and loading [(Fig. 2)]. This, in turn, means that the deformations of the already exploited portion of heading are proportional to the pressure changes.

Jan 1, 1982

By P. Zhang

A multiyear, comprehensive study of flotation reagents used in phosphate beneficiation was conducted. The study involved the evaluation of pure fatty acid compounds, comparison of various anionic collectors and testing of iso-acids. Various C12 to C22 fatty acids were tested as Florida phosphate collectors. The saturated fatty acids were found to be very poor collectors when using the standard conditioning procedure, whereas the unsaturated C16 to C22 fatty acids showed fair to good phosphate collecting ability. The C18 fatty acids oleic, impure oleic and linoleic and the C20 eicosenoic acid were shown to be the best phosphate collectors. The best flotation results were obtained using Liqro GA tall oil and oleic acid. Four isostearic/iso oleic acid type fatty acid collectors were compared with a commercial grade oleic acid and with Liqro GA tall oil as phosphate collectors using standard laboratory conditioning and flotation procedures. The most selective collector evaluated was Century 1108, a high isostearic acid-type reagent. However, it was concluded that this excellent-performing reagent was too expensive for commercial use. Overall, the most promising reagent was probably Century MO-5. This collector is essentially an iso-oleic acid/stearic acid mixture (not isostearic acid), and it costs much less. This program laid a sound foundation for developing single collector, all anionic flotation processes.

Jan 1, 2009

By J. A. Organiscak

This paper describes the research con-ducted on bit wear and respirable dust generation conducted by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy, and dust of one conical bit type when cutting coal. The objective of the USBM study was to identify qualitative bit selection guidelines for cut-ting rock; WVU's research objective was to determine optimum bit replacement guidelines. These research studies both found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1995

By A. W. Khair, J. A. Organiscak, M. Ahmad

This paper describes research that seas conducted on bit wear and respirable-dust generation. The investigation was performed by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy and dust of one type of conical bit cutting coal. The objective of the USBM study was to identify qualitative bit-selection guidelines. The objective of WVU's research was to determine optimum bit-replacement guidelines. Both research studies found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1996

By R. Jin

Fine coal flotation using gaseous carbon dioxide has demonstrated the potential for producing superclean coal. The success of this new flotation .procedure is attributed to the coal's high adsorption potential for CO2. To understand the nature of gas-phase CO2 adsorption at the coal surface, in-situ FTIR spectroscopy in a controlled-environment chamber with an ultravacuum sys-tem has been used and the results are discussed in view of other experimental results from differential scanning calorimetry. It has been found that specifically adsorbed CO2 molecules at the coal surface are polarized and have a characteristic doublet at 2336 and 2361 cm-1. Two adsorption states have been proposed to account for the doublet observed from in-situ FTIR spectroscopy measurements. It is believed that the band at 2336 cm-1 originates from the activated site adsorption of CO2 and that the band at 2361 cm-1 arises due to the molecular aggregation of CO2 within the coal pores.

Jan 1, 1988

Oil from shales has long been a source of fuel in foreign countries; however, in the fuel economy of the United States this source is classed as a reserve for future needs. In fad, shale oil has never been produced here in quantities necessary to establish oil-shale utilization as a sustained industry. The first known resources of stored energy that man endeavored to utilize were probably wood and water, and from these he directly obtained heat and power, respectively. With the evolution of man came the search for and the development and use of other natural fuel resources, the series progressing through the solid, liquid, and gaseous fuels until today those of one type can be converted into another, depending upon the use for which they are intended. The most important fuels are those that appear naturally in the most concentrated, conveniently obtainable, and usable forms. With the discovery of each new and more concentrated fuel there has been an appreciable increase in the importance of and number of devices for converting these fuels into energy.

Jan 1, 1938

By H. Wen

"Taking the long flame coal, gas-fat coal and anthracite as samples, we tested the adsorption quantity to single component gas of N2, CO2 and CH4 under atmospheric pressure phase at different temperatures. Then we analyzed the adsorption characteristics and models of different metamorphic coals. The results show that metamorphic grade, temperature and gases species are main factors to adsorption quantity of coal. The higher and lower metamorphic grade of coal have greatly influence on adsorption capacity while moderate grade of coal has opposite result. The coal adsorption amount to three single component gases under the same experimental condition is CO2> CH4> N2.The simulation precision order of four adsorption models is quadratic curve model > Freundlich isotherm model> Langmuir model >logarithmic curve model. Quadratic curve model and Freundlich isotherm model both can accurately describe the adsorption behaviors of N2 and CH4, different isothermal adsorption curve of CO2 needs two kinds or more models to describe. This has a reference value to the study of adsorption characteristics and models to single component gases.INTRODUCTION Adsorption is the interfacial phenomena that concentration of single or multiple components in the interface layer is different from the bulk phase (1964). Adsorption model is mathematical models to describe the adsorption characteristics of the adsorbent, mainly reflected to fitting effect of gas adsorption isotherm, which contribute to deeply understand the adsorption characteristics of adsorbent. Many scholars have carried out extensively experimental studies of the coal adsorption process from different angles. Zhao (2010) studied the influence of coal metamorphism to pore development of coal seam through a variety of experimental methods. Zhang (2006) analyzed the adsorption capacity and the controlling factors from three aspects of the coal rank, maceral and coal mass deformation. Cheng et al., (2002) studied the influence of pore size distribution of different rank coals to adsorption constants. Zhong (2002) carried out varieties of isothermal assay and established the prediction method of coal seam adsorption affected by a variety of conditions. R. M. Bustin (1998) proposed that we could not simply describe the change law of coal adsorption capacity and maceral content by a fixed parameter, and the adsorption capacity of the same coal rank also has great change. C. R. Clarkson et al., (1997) used four different adsorption models to describe the coal methane adsorption process, and the fitting precision of adsorption models is D-A equation >D-R equation > BET equation> Langmuir equation. Gasem, K et al., (2003) found that the fitted isothermal adsorption curve of D-A equation and BET equation are better than Langmuir equation under high pressure condition, while D-R equation and BET model are better to CO2 adsorption. In recent years, scholars’ at home and abroad research achievements of coal adsorption focused on high-pressure stage (about 0~15 MPa), mainly for coalbed methane exploitation, carbon dioxide trapping and sealing technology development, but the study of coal adsorption under atmospheric pressure phase is little. In this paper, we analyzed the adsorption characteristics and models under atmospheric pressure phase, it has a reference value to the study of characteristics and models to single component gas."

Jan 1, 2015

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By F. N. Kissell, W. E. Schroeder, N. I. Jayaraman

This article discusses methods of improving airborne capture by conventional dust suppression systems. The work was performed in a full-scale plywood model of a mine entry with a wooden mockup of a Joy 12 CM continuous miner. Dust was introduced at the front of the entry, and water sprays knocked down part of the dust cloud. Sampling in the return air determined the percentage dust reduction. Based on the results, guidelines are offered for continuous miner spray systems to control dust. Empirical relations have been developed to determine the effect of changes in water spray pressure on air movement, dust knockdown, and pollutant concentrations in the face return. Nozzle selection and arrangement are discussed for high dust knockdown efficiencies.

Jan 1, 1986

By Gordon C. Hicks

Prior to 1950 most fertilizer manufactured in the United States was produced in a nongranular form. In such form, the material caked when stored and was extremely dusty when applied in the field. About this time a wide interest developed in the fertilizer industry for the manufacture of a granular, high-analysis fertilizer of improved physical properties. Thus, TVA began work on fertilizer granulation about 1950 using both a pugmill (double-shaft paddle mixer) for a thick slurry of nitric phosphate and a continuous ammoniator-granulator drum for superphosphate-base mixed fertilizer. Granulation in these units was mainly by agglomeration. The liquid phase generated by the moisture and by the heat of reaction of ammonia with acidic materials, such as superphosphate and sulfuric or phosphoric acids, resulted in agglomeration of the solid ingredients. About 1956, TVA began studies of the use of a pan or disk granulator for production of ammonium nitrate or other fertilizers containing a large proportion of ammonium nitrate, such as 30-10-0 ammonium phosphate nitrate. This is the layering method of granulation. More recently, TVA has demonstrated pan granulation of urea from a highly concentrated solution and granulation of ammonium polyphosphate melts in a pugmill. The bulk of TVA studies throughout the years has related to use of the drum granulator. About 200 granulation plants in the United States have been licensed and built to use the TVA continuous ammoniator-granulator; it is estimated that more than half of the 20 million tons of mixed fertilizer used in the United States in 1974/1975 was produced in these plants. Some other granulation processes developed for use in the drum granulator include diammonium phosphate, monoammonium phosphate, urea- ammonium phosphate, ammoniated superphosphate, and most recently, NPK fertilizers by melt granulation using a pipe reactor.

Jan 1, 1977

By Andrzej M. Wala

A knowledge of the friction factor (K-factor) is necessary in planning and designing mine ventilation systems for least cost and highest effectiveness. The friction factor used must be accurate and reliable for correct estimation of airway resistances. At present, the friction factors are determined by using tables of published values. These values were established principally for metal-mine openings having small effective areas. This presents a problem to the ventilation design engineer whose responsibilities center around the design of effective ventilation systems for large room-and- pillar mechanized underground coal mines. Friction factors selected from these tables could be excessively conservative for large scale room-and- pillar operations. With only limited data on the K-factor (which are considerably site dependent) for Kentucky's coal mines and for all the above mentioned reasons, it was concluded that there is a need for field investigations to determine these values in-situ for existing mining conditions in Kentucky. The author describe the study carried out in ten coal mines located in eastern and western Kentucky and present the results of the investigation in both tabular and graphical form.

Jan 1, 1991

By Pinghui J

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

By T. H. Patching, M. W. Mikhail

"The gas sorption and emission characteristic of coals are important to the planning and conduct of mining operations. Methane drainage from coal strata can also provide a supply of fuel in certain circumstances. Gas emissions have also created hazards during the handling and transport of coals and the release of gas also appears to be related to the yield of fine sizes during mining and processing operations.This paper summarizes studies at the University of Alberta on the permeability and gas emission of certain bituminous coals. Permeability of 'solid' samples was found to be drastically reduced by confining pressure. An emission index, .P, which has been related to outbursting behaviour of coals, has also been related to the proportion of fine s in cleaning plants. Gas sorption isotherms are dependent on temperature, moisture content, the gas involved and the type of coal and can be approximately expressed by the Langmuir or the Freundlich equations. Sorption values in sections taken across a given seam were similar but considerable differences were found in . P indices in the different coal layers of a seam.IntroductionThe emission of gases, especially of methane, from coal has been a subject of great interest (and sometimes a matter of life and death), to those who dig and handle coal since it was first mined from underground pit s. Many studies and investigations have been carried out on gas occurrences and emissions but our knowledge of the precise mechanisms of gas sorption, desorption and flow from coal is still incomplete. It is the purpose of this paper to review the principal factors involved in these processes and to briefly rep ort some of the results that have been obtained by studies in the laboratories of the Department of Mineral Engineering, University of Alberta, and Coal Research Laboratory, Edmonton, CANMET"

Jan 1, 1986

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By F. W. Wood

ORIGINAL experimentation in specially designed arc-melting furnaces and a comprehensive review of technical literature have helped with an understanding of electric arcs as used in metallurgical applications. Results relevant to the distribution of electric potentials and currents, temperatures, pressures, the consumption of electrodes, the identities of particles participating in electrical conduction, and the modes and mechanisms of discharge are presented and discussed. Present knowledge of high-current arcs is insufficient to test pertinent theoretical suggestions. However, the chief doubts concern the identities and the liberation or formation of current-carrying particles. It seems that either (1) novel formulations of existing concepts are needed, or (2) essentially new concepts must be recognized to explain observations. An analysis of the situation has led the authors to favor the latter possibility and to suggest the existence of supplementary conducting particles. The conduction of current by the streaming of charged agglomerates is postulated. Another outgrowth of analysis is an equation for the arc potential as a function of current densities in the arc. In lieu of conclusions, the potentialities of practical applications and specific needs for fundamental clarification are summarized.

Jan 1, 1965

By H. Foster Bain

I. INTRODUCTION. By H. FOSTER BAIN.+ THE recently aroused public interest in the conservation of our natural resources has peculiar importance to mining-men, since they deal with resources which are stored products. Within certain limits, the fertility of a worn-out soil may be restored, deforested areas can be replanted, one year's wasted water-supply is followed by another; but coal and ores, once taken out, cannot be mined again, and should therefore be conserved with especial care. This means, however, not that mining should be restricted, but that it should be done most economically and with the minimum of waste.

Nov 1, 1908

By F. Qian

Direct impingement of molten metal baths by a gas jet is commonly encountered in such processes as BOF and electric arc furnace steelmaking. Shape and local fluid mechanics in the impinging region is important because it determines the interaction of the metal pool with the surroundings. Goal of the present work is to characterize and understand the interfaces at the impinging region. Using a physical model consisting of water/corn oil and water/kerosene as surrogates for metal/slag, interface shapes for slag-gas, slag-metal and metal-gas are investigated. Influence of transport properties of the two liquids on the shape and flow fields are also experimentally determined under various impinging jet conditions, namely jet momentum and jet height. The viscosity of the slag layer (corn oil or kerosene) has the most significant effect on the interface shape and the induced flow fields. The interface shapes were measured both photographically and by using a surface- tracking resistance probe. The limiting condition at which the jet breaks through the corn oil or kerosene layer and reaches the water layer was determined experimentally

Jan 1, 1994

Metal smelting is seeing a continual increase in intensity and throughput in recent years. This is done with increasing demand for cost/capital efficiency, higher recovery, and managed environmental impact, among other things. With the development of more intense smelting processes, the issues of refractory wear, mixing and separation of reacting phases and the nature of the reactions between them become more prominent. Understanding of interfacial phenomena is in growing need, in addition to knowledge of the bulk properties of equilibrium and transportation. The GKW CRC has a suite of projects aimed at developing various techniques and expertise to provide information of interfaces in metallurgical systems. This article illustrates some recent development in this area, particularly in studies of melt/refractory contacts, the determination of surface and interfacial tension of metal/slag/matte melts, modelling slag-metal mixing and studies of kinetics of the smelting reactions.

Jan 1, 2000

By P. He

Abstract This paper introduces tested results of rock-socketed pile in Nanjing, Wuhan and Chongqing. From a force- transfer model, a distribution of axial force for pile-body and inlaid resistance for rock-socketed pile was deduced. Comparing the results of test and calculation, it shows that the calculation result coincide with the test result. Keywords rock-socketed pile, load transfer, inlaid resistance, end resistance. Zusammenfassung: dieser text legt eine kuyze Einfuehyung ueber die Erfolge wissenschaftlicher Forschungsarbeit in bezug auf die Grundprinzipien der Mechanik von Belastungsuebermittlung der Einlegesteinpfeilers der Durch Benutzung von Ausgleich/Balance der inneren Kraft und Deformationskoordinierung wird das mechanische Modell der Belastungsuebermittlung des Einlegesteinpfeilers aufgestellt. Vom lebendigen Beispiel wird dia Wellenkraft des Steinpfeilera und die Verteilungskurve Einlegebfestigungskraft ausgelegt, man hat diess bereits mit der tatsaechlichen genessenen Kurve verglichen. Schluesselwoerter: Einlegesteinpfeilers, Belastungsuebermittlung, Einlegebfestigungskraft, Seitenwiderstand. Résumé - Le présent article décrit de façon succincte des résultats de la recherche sur le mécanisme du transfert de chargement du pieu d’ancrage au massif. Une modèle dynamique du transfert de chargement du pieu d’ancrage au massif est ainsi établie avec l’application des conditions de l’équilibre de contraintes internes et de coordination de la déformation. L’expérimentation sur des exemples réels a permis de mettre à jour des courbes de distribution de la force axiale du corps du pieu et de la force d’ancrage avec comparaison aux courbes effectivement mesurées in situ. Mots clés - Pieu d’ancrage au massif, Transfert de chargement, Force d’ancrage, Résistance à la pointe

Jan 1, 2003

By Stefan S. Kapusniak, Nichol Riggott, Stephen F. Smith

Stability investigations have been carried out in a number of major coal mining tunnels in the U.K. using various instrumentatcon techniques. The paper describes these instrumentation methods and presents results from studies in several tunnels. Both long and short term stability aspects are discussed. Prediction of tunnel stability is examined in relation to tunnel support requirements. Computer simulation techniques are used along with actual underground measurements to identify tunnel design parameters for influencing choice of support and prediction of long term stability.

Jan 1, 1984