Search Documents

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951

By Rudrajit Mitra, Wesley B. Johnson, Erik C. Westman

The ability to understand stress redistribution within a mine allows greater extraction efficiency with reduced safety concerns. Stress redistribution has been examined at the laboratory scale using ultrasonic tomography and numerical modeling using PFC3D. A data acquisition system was built to obtain tomograms as samples are loaded in uniaxial compression. Limestone samples were loaded to failure. Three-dimensional tomograms of the samples correlate to various stress distributions. The tomograms are compared to analytical and PFC3D results.

Jan 1, 2005

By ERIK C. WESTMAN, JESSICA M. WEMPEN, DALLAN J. COONS, WILLIAM G. PARISEAU, MICHAEL K. MCCARTER

Safe, efficient underground mining is dependent upon proper pillar sizing. Pillar sizing is typically based on a combination of observation of prior behavior, point measurements, theory and numerical modeling. The actual stress redistribution within a pillar, while assumed for many years, has rarely been imaged. Such imaging can help confirm whether or not theoretical and numerical modeling methods agree with actual conditions within a pillar. This research presents a case study from a longwall mine in the western United States. A two-entry, gate-road yield pillar in the headgate of the mine was instrumented with seismometers and convergence monitoring stations, and was monitored over a period of about six months as the longwall face approached the pillar. In this paper, the stress distribution imaged using seismic tomography is compared to the stress distribution expected from theoretical models, geotechnical measurements and numerical models. The tomography results generally agree with those proposed by theory, convergence measurements and numerical modeling results. The agreement of the methods provides validation for the theorized stress redistribution, and this study provides further evidence that tomography can indicate the redistribution of induced stress within a mined rockmass and is another tool available to ensure that mining is conducted safely and efficiently.

Aug 1, 2022

By Jessica M. Wempen, William G. Pariseau, Dallan J. Coons, Michael K. McCarter, Erik C. Westman

The abstract discusses the importance of proper pillar sizing in underground mining for safety and efficiency. It highlights the use of theoretical models, geotechnical measurements, and numerical modeling in predicting pillar behavior. The research focuses on using seismic tomography to image stress changes in a yield pillar at a longwall mine as the longwall face approaches. The study aims to compare the stress distribution imaged using tomography with theoretical models, geotechnical measurements, and numerical models.

Mar 18, 2022

By A. Manohar Rao

Underground mining in general and more so the coal mining is a hazardous venture as it is a struggle against nature and natural forces. The stability of roadways has a direct impact on production and productivity. The roadway stability can be strongly influenced by the direction of the drivage. The stress studies are useful to provide a frame work for understanding the influence of drivage direction on roadway conditions, and to illustrate how mapping techniques can enhance this understanding. The act of mining can concentrate and re-orient the original stresses. Whenever coal is removed, the overburden weight that it carried is transferred. Vertical stresses are similarly affected when the roof is deformed or failed. The Singareni Collieries Company Ltd., a joint Public sector undertaking of the Government of Andhra Pradesh and India is conducting coalmining operations in the Godavari Valley Coalfield and is catering to the needs of a large part of South India. With the technology update, it is looking for safe mining and to achieve higher production. As a part of this, an attempt is made to understand the stress conditions prevailing on the mine blocks by different ways and means in terms of geology, structure and tectonics of the Godavari Valley coalfield, satellite imagery studies, cleat pattern, stress measurement studies conducted in different mine blocks, and stress mapping technique.

Aug 1, 2013

By K. Y. Haramy

Deep coal mines with strong roof and floor rock frequently encounter face and rib bursts. The burst problem is becoming more severe as mining depth increases, prompting efforts to relieve high stress areas ahead of mining. Successful stress relief reduces the occurrence of uncontrolled coal bursts. This report by the Bureau of Mines, U.S. Department of the Interior, presents a review of the most widely used methods to detect and destress high stress zones along coal faces. Stress-related burst problems and destressing efforts at a cooperating mine were investigated. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three- dimensional, multiple-seam computer modeling program, "MULSIM?, was used to evaluate the effectiveness of stress relief methods. Modeling results and guidelines for destressing are presented. Results indicate that dangerously high stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1987

By L. F. Tedsen, A. E. Flanigan, J. E. Dorn

SINCE aluminum-alloy sheet may be used occasionally at moderately elevated temperatures, the effects of temperature en the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 375°F. This paper deals with stress-rupture and [ ] creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24S-T Alclad 24S-T8I Alclad 24S-T86 Alclad 75S-T R301-T (clad) [ ] Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 211°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to boo hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). MATERIALS Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1946

By A. S. Nowick, E. S. Machlin

ONE of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.1 During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time required for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error.2~3 This method of showing stress-rupture data has been adopted by many investigators and the KACA.4 By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, 100, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time for rupture on stress, temperature, com- position, and structure. In order to obtain this information, an investigation was made at the KACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given com- position and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efficiency and power output of gas turbines used in aircraft propulsion can be increased. THEORY The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 eveloped by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate- process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process.'' For example, in a chemical reaction the unit process is

Jan 1, 1947

Reliably measure stress chan¬ges in order to assess stability of mine openings. Approach: A durable, permissible, sensor and readout system have been developed and tested. How It Works: The stress sensing element is a taut steel wire which is, vibrated at its natural frequency, If the tension on the wire is changed because of deformation of the sensor housing, the natural frequency of the wire changes. This effect is similar to decreasing or increasing the pitch of a violin string by loosening or tightening it. Because the stress sensor electrical output is a frequency signal, rather than an amplitude signal, its accuracy is unaffected by the resistance of the signal wire, or other attenuation. Signal wires can be a mile or longer without affecting accuracy. When a button is pushed on the readout box, the sensor wire is electromagnetically excited and vibrates at its natural frequency. That signal causes a readout in illuminated digits. (By referring to calibration chart and the previous reading, the user knows the change in stress.) This system is permissible. To install the sensor, a slightly oversize hole is drilled into the mine pillar. Next, a special tool is used to both position the sensor and wedge it in place. Figure 1, shows the sensor and its integral wedge and hole-fitting piece.

Jan 1, 1976

By Paulo César Lemes de Almeida

No projeto da usina da VSB, em Jeceaba – MG estão contemplados dois altos-fornos de 350 m3 de volume útil e uma máquina de lingotar gusa (MLG) com capacidade de 150 t/h. Um destes altos-fornos já está pronto para o início de operação. Visando realizar os testes a quente da MLG a aciaria da VSB tem produzido aço com alto teor de carbono para testar o equipamento. Realizaram-se 07 etapas de testes que possibilitaram a implantação de algumas melhorias na MLG, coletar dados sobre a logística de movimentação de panelas, estimar perdas térmicas do gusa e treinar o pessoal para a operação. Nesta contribuição técnica descrevem-se os testes realizados e as modificações decorrentes.

Aug 1, 2018

By Vedala Sastry

Longwall mining for coal extraction in deeper deposits is gaining momentum in India, due to the increasing stripping ratios and depletion of shallow deposits amenable for surface mining. In longwall mining, presence of multiple seams with varying interburden thickness is a major problem especially while planning for over-mining. An investigation program was taken up to analyze the effect of the presence of goaf and virgin coal blocks in already developed and extracted lower seam by bord and pillar mining, on the stress distribution in the longwall panel in upper seam. Studies revealed marginal increase in horizontal and shear stress as longwall face passes above goaf to the virgin area present in lower seam. Stress distribution over chock shields was considerably affected when the face in upper seam reached 15-25m zone above the galleries in the lower seam. A clear influence of the presence of solid coal, galleries and goaf in lower seam was found in the loading of longwall panel in upper seam.

Jan 1, 2007

By H. Maleki

The U.S. Bureau of Mines pioneered the use of borehole deformation gauges and overcoring techniques to measure in situ stress. These measurements provide input to structural mine design and support selection for specific geologic conditions. This paper presents recent stress measurements in a western U.S. coal mine where the orientation of the stress field remained relatively unchanged over distances of several kilometers. The horizontal stress magnitude increased with depth of cover and in relation to major geologic structures. Local variations in roof stress profiles were used to develop generic models relating stress arching to strata stiffness and the inelastic behavior of mine roof.

Jan 1, 1994

By X. Li, J. C. Stankus, J. Ma, H. Chen

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult, because a slope will transverse through many types of strata. Over the last few years, Keystone Mining Services LLC, an affiliate company of the Jennmar Corporation, has developed a new methodology designated the “Stress, geologic and support design system (SGS).” The method analyzes the stress, geology and support design for a mine slope. The method has been successfully applied in various new slopes across the United States, and ground control plans developed using SGS methodology has helped coal companies successfully pass review and/or hearings by state and federal regulatory agencies. With a case application in the U.S. Midwest, this paper details and demonstrates the main concepts of the methodology, including (1) analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) primary and supplemental support design; (3) long-term support design in the form of steel square sets or arches and (4) validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By B. H. Gardner, S. Serata, D. Dickie

Since 1958, the Sifto Salt Division of Domtar, Inc., has operated the Goderich (Ontario) salt mine in Michigan basin bedded halite, with shafts located on Lake Huron's eastern bank. Initial mining utilized a conventional room and pi1lar pattern. However, roof deterioration developed. Incidence of progressive upward failure of saltback and over1yings ha1ey-do1omite layers intensified with entry aging. Studies were therefore initiated on new mining patterns utilizing the Serata Stress Control Method. Pursuant thereto, three test areas, indicated in the mine plan of Fig. 1, were designed and excavated. Full conversion to Stress Control mining was effected in January, 1983. This paper focusses on the instrumentation work in the third test area. Test Area 3 was designed to validate the excavation geometry of the new stress-controlled main entry system. The testing of that design was accomplished, in part, by comprehensive in situ stress, property, and deformation measurements on the performance of the model main entry section of Test Area 3. The paper describes: (1) the theoretical background of the SPDR/Stress Control Method; (2) specific problems and objectives addressed by the 1983 program of in situ measurements, (3) measurement results; and (4) conclusions drawn therefrom.

Jan 1, 1986

By G. P. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Stress-corrosion cracking (SCC) tests were conducted in the near-neutral pH standard solution, NS4, and in an actual soil solution, using four-point bending at high a stress ratio and low frequency conditions very similar to those of operational pipelines. Pitting incubation appeared first and then pitting initiated and grew in both solutions although there were many more pits on the specimen tested in soil purged with 5% CO2 + 95% N2 than in the specimen tested in NS4 solution purged with the same gas. These observations show that samples in soil solution are more susceptible to pitting than those in NS4 solution. When the pit reached a critical size, the increased stress concentration around the pits, resulted in the transition to a crack.

Jan 1, 2005

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,' who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By Alan Morris

SEASON cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes are fairly well understood and means for its prevention are inexpensive and effective, .so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free- from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,1 in discussing a paper by Hatfield and Thirkell, says : "He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultane-us corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack.

Jan 1, 1930

By J. H. Bulloch

The paper gives an assessment of the available data on the linear elastic fracture mechanics involved in stress corrosion cracking and in the behaviour of reactor pressure-vessel materials exposed to a simulated pressurized water-reactor environment. As a result of the different experimental techniques used in the various studies mentioned, only a few detailed conclusions can be drawn. The data from constant-displacement wedge-opening loading (WOL) tests, with the exception of one study, exhibited very limited or no crack extension during exposure periods of up to 14000 hours. The data from constant-load tests indicated evidence of crack extension, but the nature and extent of the crack extension are still unclear. When crack extension did occur, it was exclusively transgranular in nature. Certain differences in the available test data are tentatively explained in terms of the experimental procedures used, and the need for a consistent code of experimental techniques is highlighted.

Jan 1, 1987

By F. P. A. Robinson, C. R. Thomas

Stress-corrosion studies on materials used for surgical implants * by C. R. THOMAS and F. P. A. ROBINSON Samples of Vitallium (a cobalt-chromium alloy), 316L stainless steel, and titanium T318 were subjected to the boiling magnesium chloride test so thattheir susceptibility to stress-corrosion cracking could be determined, and their behaviour under service conditions was then assessed. Stress-corrosion cracking was confined to the stainless-steel samples, while gross pitting was detected in the samples of forged Vitallium. It was concluded that the use of stainless steel should be avoided for long-term surgical implants. Surface imperfections on the stainless steel are generally the cause of pitting, from which stress-corrosion cracks are sometimes propagated.

Jan 11, 1976