Search Documents

By E. Topuz, G. Faulkner, M. Karmis, C. Haycocks

The Appalachian coal region of Virginia, southern West Virginia and Kentucky and the extreme eastern portion of Tennessee constitutes a unique area of surface coal mining activities. The area contains a number of contiguously placed coal seams, up to a total of fourteen in some places, which vary in thickness from a few centimeters to 2,5 meters. Much of this coal is of high quality, some being the highest grade metallurgical coal found anywhere in the world. The region may be broadly characterized physiologically as a dissected plateau with a relief above the valley floors of up to 500 meters and a dendritic drainage pattern. Up to six seams may outcrop in the hillsides above drainage, many of which have been subjected to contour stripping operations. Prior to the passage of the surface mining reclamation act, little effort was made to reclaim stripped areas. The passage of the strip mining act, including the controversial requirement for returning the land to its approximate original contour, has forced intensive recla¬mation efforts from the mining industry. The wisdom of this original contour requirement has been the subject of considerable debate and litigation, mainly because of its cost, inconvenience, and value of the land after it has been reclaimed. Regardless of whether recla¬mation is carried out, under current practices slope failures do occur. This in effect circumvents the intent of the law and can expose large unvegetated spoil areas, and contribute to hillside erosion and stream silting. Such failures must be eliminated if further costly reclamation efforts are to be avoided.

Jan 1, 1983

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By Burt Hartmann

The nation's ever-expanding construction and mining activity has placed an increasing demand upon engineers and geologists to design and construct stable slopes in earth materials-soil and rock. Man's attempt to handle these slope stability problems has been based primarily on practical experience and the resulting theories formulated to explain the phenomena. Too many instances occur when man is faced with a slope stability problem that has not yet been experienced and doesn't lend itself to solution by any existing theory. At this point he must extend himself in using his engineering judgment to arrive at a reasonable and safe design. As past experience has shown, all of the "safe designs" are not really safe. Sometimes they result in embarrassing failures. Measurements provide the key to understanding and controlling natural phenomena. We cannot hope to gain control of the slope stability problem until we understand the causes of slope failure, their behavior with respect to time and their relative magnitudes. Measurements required for an adequate definition of any slope problem must be of the highest reliability because of the importance of decisions which must be based on them. For this reason, direct measurements of movement, shear strength, water pressure, etc. of the unstable mass are preferable to indirect measurements of other physical properties. Movement instruments which can be positioned inside of the slope mass (within boreholes) are among the most useful in diagnosis and/or monitoring of slope movements. The higher the sensitivity and il-measurement precision possible with borehole instruments, the quicker the required information can be obtained and the more exactly may hazardous conditions be observed. A high density of measuring points in a single drill hole is deemed essential for diagnostic purposes. Behavior gradients may thus be obtained. The Pressure Meter (Fig. 1) can be used to measure a relative strength

Jan 1, 1968

By Trudinger JP

Mt. Newman Mining Company Pty. Ltd.3 oper ates the Mt. Whaleback iron ore mine in the Ham- ersley Iron Ore Province of Western Australia. The present rate of production of high grade hematite iron ore is 33 million tonnes per year. Mining is by open cut quarrying,with 15m high benches. The present quarry operations will be extended to a large oval pit to win over 1400 million tonnes of iron ore. The pit slopes will extend up to 500m in depth and the perimet- er of the slopes will exceed 15km. Sixty per- cent of the ore is below the water table, which presently lies 45m below the general plain level Dames & Moore, rock mechanics consultants designed the pit slopes during early mine devel- opment to ensure an economic and safe operation.

Jan 1, 1975

By M Edgar, G Pattemore, M Auad, K Job, A Job, S Gale

In recent decades, significant advances have improved the modelling techniques for predicting slope failure. Predicting failures is vital in open pit mining due to the significant risk posed to personnel and equipment from unstable pit walls. Failures not only cause harm and damage to people and equipment but also cause delays to production and subsequently increase operational costs. Coupled with improvements in modelling techniques, utilisation of advanced scanning systems, such as high-definition imagery from UAVs has enabled faster and more precise mapping and modelling. However, one key element required for accurate slope stability modelling and monitoring is the ability for mine geotechnical engineers to have an accurate understanding of the mineralogy and moisture content of slopes, in real-time. To address this challenge, research has been undertaken to utilise hyperspectral imaging across a broad spectrum, combined with high-definition imagery, and LiDAR to scan slopes for minerals and moisture content. In addition to accurately mapping mineralogy and moisture, the data must be collected autonomously and remotely to ensure ongoing safety. The results show that there are many direct and indirect benefits from this new technology, including the ability to monitor slopes at a safe distance and in real-time, improved accuracy of modelling, detection of risks, and improving the automation workflow for geotechnical engineers. The paper presents recommendations for the implementation of the technology in open cut mining environments.

Jun 22, 2022

By D J. Clark, S Hewson, T Li

Cadia Hill Pit is a gold copper porphyry deposit hosted in monzonite. The pit slope design is primarily based on structural controls related to faults and shears with largely massive rock masses between the structures. The slope design attempts to achieve an optimum configuration at a bench to overall scale, considering economics and safety implications against the geotechnical and structural conditions. To date the slopes have been mined at interramp angles of up to 60¦ over heights of 120 m. Limited slope and batter failures that have occurred are structurally controlled and occur rapidly. The pit-mining schedule requires concurrent mining of part of the final pit walls and the progressive interim cutbacks. Engineering and operational solutions to hazard reduction and risk management issues have been implemented wherever viable to æengineerÆ out the hazard and mitigate the risks. However, comprehensive management plans and operating procedures have also played a vital role. This paper details the management plan and the operating procedures that have been developed and implemented to mitigate the risks associated with rock falls.

Jan 1, 2003

By Carl D. Broadbent

The goal of slope mechanics is to achieve efficient and safe pit slopes. In the case of ultimate mine slopes the objective is to minimize the stripping ratio by steepening the slopes to their maximum stable limit. On the other hand, the inclination of working slopes is normally established by operating space requirements and the function of slope mechanics should be the continuous surveillance of slope conditions to assure long-term stability and to provide timely warning of impending slides so that corrective measures may be incorporated in production planning. In 1956 Kennecott instituted a program to provide the resources necessary to develop and maintain a slope mechanics capability, including technical knowledge, engineers, and instruments. Although the goal has not been fully achieved, very significant progress has been made. Other papers (3, 4, 7, 8, & 12) have described the purposes and detailed results of the most recent study carried out at the Kimbley Pit. The study has provided valuable experience and has given the industry a three dimensional picture of the stability variables that influence a mine slope. The study has better defined those areas which require further investigation and has indicated those design and analytical techniques which can be used with confidence. In effect, the study has paved the way for the next step; that of refining the design process and applying it for profit.

Jan 1, 1968

By N Harries

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The æslope stability radarÆ (SSR) has been developed to better manage those risks. The SSR can remotely scan a rock slope to continuously measure any movement of the face. The system can detect and alert users of wall movements with submillimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, Africa, Chile and the United States. Greater than 100 rock falls and waste dump failures (from several tonnes to millions of tonnes) have been monitored, and on every occasion precursor æwarningÆ movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper presents recent case studies of how the SSR technology has provided safety and productivity benefits to large open cut metalliferous mines.

Jan 1, 2007

By Neal Harries

Ground movement is normal in open cut mining operations, mainly caused by excavation response and blasting. Movement of the ground can be acceptable provided it is not unexpected and catastrophic. However, in steep mine walls and the very large open pits being developed today the consequence of slope collapse can be catastrophic. Such risks can be minimized at the planning stage by reducing slope angles, but this carries a very high cost. Also, instabilities which develop whilst mining can lead to ore reserves being quarantined, which represent a high cost to the mining operation. In spite of such safety measures, unexpected failures have occurred in the past. These issues motivated the development and production of the slope stability radar (SSR). There are currently over 80 GroundProbe SSR systems deployed in metalliferous and coal mines in 17 countries. The unexpected failure of rock walls at mining sites is a major cause of death and serious injury. Slope failure is also one of the major causes of economic and production losses. An unexpected wall failure can bury critical equipment. It also disrupts the mine plan. It is common to cease mining for several days or weeks following a wall collapse due to uncertainty over stability. Direct economic losses in remediation alone can easily exceed $1,000,000 per incident. The economic costs of injury or fatality are much higher including closure of mines during the incident investigation process. Massive wall failure can result in direct and indirect costs measured in millions of dollars. This paper will present some recent case studies of the SSR operation in open cut mines in North America, including Thompson Creek Mining Company (Idaho), Smoky Canyon Mine (Idaho), and a general case study on extreme cold weather use of the SSR.

May 1, 2009

Slope stability is a critical safety and production issue for open cut mines. The æslope stability radarÆ has been developed to remotely scan a rock slope to continuously measure the movement of the face. The system can detect and alert movements of a rough wall with sub-millimetre precision, and with reliability and resolution. The advantage of the slope stability radar over other monitoring techniques is that it provides full area coverage without the need for mounted reflectors or equipment on the wall. In addition, the radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. The measurement technique is tolerant of vibrations and overcomes the need for a highly stable footing required by traditional surveying systems, making it easy to move from one location to another. The system is self-powered and designed for minimal maintenance. Radar displacement images, co-registered with digital photography images, are transferred from the radar site in the pit to the mine office via a radio telemetry link. Custom-written software provides mine managers and geotechnical engineers with a complete picture of slope movements over defined time intervals. The time-history of the movement of any selected points or regions on the slope can also be displayed. Also provided is the ability to set movement thresholds that will trigger alarms at the radar site or mine office. The system has been used at numerous coal and metalliferous mines in Australia, and has provided real-time monitoring of slope stability during active mining operations. More than 20 rock wall and spoil failures have been captured by the system, and on every occasion adequate warning was provided to mine operators. The high level of movement precision and broad area coverage of the rock face provides a better understanding of the geodynamics, which leads to extra warning time. This technology enables a radical change in the management of risks in open cut mining operations.

Jan 1, 2003

By Jorge Cárdenas, Diego Gamarra

In previous phases of the mine, a landslide resulted in several losses in production delays. The stability of slopes in a mining operation is critical for the sustainability of the operation, as they are exposed to vibrations and damage caused by blasting. Therefore, it is essential to implement controls and innovative technologies to reduce these vibrations levels. This study focuses on the application of low-energy emulsions with lower densities than conventional explosives, developed to reduce vibrations and the energy delivered to the rock mass adjacent to the near blast holes as a buffer row. Near field studies were carried out by embedding triaxial geophones. Vibrations were recorded, and mathematical models of vibration associated with different types of explosive mixtures were generated. This allowed us to determine the benefit of implementing low-density explosives in reducing vibrations compared to Heavy ANFO explosives. The application of low-energy explosives with densities ranging from 0.7 to 0.8 g/cm³ and Relative Bulk Strength (RBS) of 51-65 allows for a 40% reduction in vibrations compared to the detonation of Heavy ANFO explosives.

Jan 21, 2025

By P. Ravanal, J. Blazquez, F. Ortega, P. Couceiro, J. Navarro

Massive blasting technique is an interesting alternative to optimize mining’s performance by enhancing digging rates and overall operation’s activities, especially when a reduced operational bench width is available. The exploitation of a huge bench through multiple blasts would mean a potential reduction in productivity and higher operational difficulties. In such hard circumstances, combined with complex geotechnical conditions, a full ground vibration analysis for near and far field vibrations are required in order to safely design and conduct the blast. In this paper, a comprehensive case study will be discussed to show how the application of massive blasting techniques was safely implemented in very complex geotechnical conditions. The proposed solution was based on performing a full ground vibration study to optimize blast design parameters, such as charging and timing, in order to fire the complete bench blast in a single shooting event, without compromising the slope stability. Thus, a massive blast with an approximate tonnage of 6.0Mt was successfully designed and blasted, attending all safety and stability criteria defined by the geotechnical and drilling and blasting departments of Minera Escondida.

Jan 1, 2024

By M. Jaramillo

The Expanded West Pit of the 15 MTY El Cerrejon Mine will reach a maximum depth of270 m. Slope stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization call for anchoring the footwall by installation of cable bolts, 9 to 33 m long, of multi-strand steel cable. For each of the 15 m high mining benches, a row of bolts is installed with variable horizontal spacing, depending on dip magnitude. Cable bolting is now standard operating practice and 11800 bolts will have been installed during the life of the mine.

Jan 1, 1995

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997

By C. O. Brawner

A recent advance in slope dewatering-depressurization and stabilization is the use of vacuum assist horizontal drainage. (Brawner and Pakalnis) Horizontal drains have been used for several decades to reduce water pressures in slopes to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by an induced negative atmospheric pressure. A research program included a laboratory model whereby the effects of vacuum drainage were evaluated. Three case studies are described where the technique has been successful. The first is in a rock slope where flows increased from 0.1 1/min. under gravity drainage up to 1.2 1/min, upon vacuum. The second study involves installation of 17 drains placed at a slightly downward gradient to intercept and de- pressurize aquifers under a major tar sand deposit in Canada. The third study was on a large open pit copper mine in British Columbia where flow increased about 30 per cent.

Jan 1, 1984

By Kessi E. Zicko, Eric A. Hackenberg, Paul J. Lewis

"Following snow melt and spring rains in 2011, a landslide measuring approximately 600 feet long and 300 feet in slope length occurred within the southbound roadway embankment of a heavily travelled 2-lane divided highway in North Central Pennsylvania. Driven steel piles were designed to stabilize the embankment slope. Factors affecting the selected stabilization technique included an adjacent reservoir, wetlands, the length and depth of the failure plane, extent of glacial lake deposits, excess pore pressures in the foundation soils, and an area of archaeological interest. Field reconnaissance and subsurface explorations including borings, instrumentation, geophysics, and laboratory testing indicated that glacial lake deposits were present in the toe region of the embankment. Instrumentation proved key in measuring excess pore pressures and in locating the failure plane, and geophysics was utilized to estimate the extent of the soft glacial lake deposits and to estimate pile lengths. The existing condition of the embankment was modeled in computer slope stability analyses, which were also used to help assign soil parameters. Significant costs were associated with constructing a berm due to the impacts on adjacent site features. Therefore, multiple rows of driven steel H-piles were designed for installation along the toe of the embankment. The design lateral load in the piles was based on slope stability analyses, and the pile size and number of piles were based on lateral pile computations with modified p-y curves to account for installing piles in an active landslide. The relationship between the factors of safety from slope stability and the LRFD pile design was significant in determining pile loads for lateral analyses.INTRODUCTIONA landslide developed along the lower portion of the southbound embankment of State Route 15 in Tioga County, Pennsylvania. The road passes through a steep valley and is located along the southern extent of the Tioga Reservoir. Although no damage to S.R. 15 was attributed to this landslide, the close proximity of the slide to the road posed a concern for the long-term stability of this section of roadway.This paper presents a summary of the site history; the subsurface conditions based on borings, instrumentation, a geophysical survey, and laboratory testing; slope stability analyses including alternatives assessment; and the pile design.SITE HISTORYS.R. 15 was originally located in the valley along the Tioga River and traversed through the towns of Tioga and Mansfield. Although the reason is unknown, it is interesting to note that Old S.R. 15 curved away from the river in the area of the landslide. In the mid 1970’s, S.R. 15 was relocated to the eastern hillside prior to construction of the Tioga-Hammond Reservoir by the U.S. Army Corps of Engineers. The relocated highway was constructed in stages. Two lanes of relocated S.R. 15 were initially constructed to carry one lane of northbound and one lane of southbound traffic. At this same time, the majority of the fill was placed for two future lanes immediately to the west, which would eventually allow for two lanes in each direction. The two eastern lanes would then carry northbound traffic after completion of the two southbound lanes to the west."

Jan 1, 2015

By A. J. Metz, Roberto Nevarez

One popular method to stabilize slopes is the use of deep foundation elements to support lateral loads from an unstable soil or rock mass. Drilled deep foundation elements are often selected due to local availability of equipment, access concerns, cost considerations and post-construction aesthetics. Often, one or more rows of deep foundation elements are installed running parallel to the slope. The elements in each row may or may not be connected through a cap beam. They work primarily in bending, and resist slope movement by transferring the earth pressures down below the potential slip surface. Design of these systems considers the effect of arching

Nov 1, 2023

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

By Y. Mitani, M. Xie, G. Zhou, T. Esaki

The assessment of landslide instability and risk has become a topic of major interest for both geoscientists and engineering professionals as well as for local communities and administrations in many parts of the world. In this paper, based on a new developed Geographic Information Systems (GIS) grid-based 3D deterministic model and taken the slope unit as the study object, the landslide hazard is mapped by the index of the 3D safety factor. Assuming the initial slip as the lower part of an ellipsoid, the 3D critical slip surface in the 3D slope stability analysis is obtained by means of a minimization of the 3D safety factor using the Monte Carlo random simulation. The failure probability of the landslide is calculated by an approximate method in which the distributions of f,c and the 3D safety factor are assumed to be in normal distributions. The assessment of the earthquake triggered landslide hazard is done by the dynamic displacement analysis using the index of the Newmark displacement. All the calculations are implemented by a computational system call 3DSLOPEGIS in that a GIS component is used for fulfilling the GIS spatial analysis function. Besides the results of 3D safety factor and probability, the possible landslide body and boundary can be three-dimensionally quantitatively identified. L’ estimation des glissement de terrain et des risques impliqués est devenu un des principal sujet de préoccupation pour les géotechniciens, mais aussi pour les ingénieurs specialisés ainsi que pour les communautés et administrations locales dans de nombreuses région du monde. Dans cette étude, basé sur un modèle de maillage 3D et une approche déterniniste couplée au Système d'Information Géographique (SIG), étudiant la stabilité des versants , le lieu d'étude à risque est maillé suivant le facteur de sécurité calculé en 3D. En supposant que le glissement initial soit la partie inférieure d'un élipsoïde, l'analyse de stabilité pour le glissement critique 3D d'un versant 3D est obtenu grace à une minimisation du facteur de sécurité en 3D utilisant la méthode de simulation aléatoire de Monte Carlo. La probabilité d'un glissement de terrain est calculée par une méthode approximative, supposant la distribution de c, f et du facteur de sécurité 3D normale. L'estimation d'un risque de glissement de terrain causé par un tremblement de terre est faite grace à une analyse du déplacement dynamique suivant l'index de Newmark. Tous les calculs sont effectués par le biais d'un système de calcul appellé 3DSLOPEGIS dans lequel te GIS est utilisé pour gérer l'analyse spatiale. En plus de cela, les résultats du coefficient de sécurité en 3D, des probabilités, le terrain susceptible de glisser, et ses limites, peuvent être quantitativement évalués en trois dimensions. Die Bewertung von Erdrutsch-Instabilität und risiko sind zu einem Thema von großen Interesse für sowohl Geowissenschaftlern und Ingenieuren als auch von Gemeinden und Verwaltungen in vielen Teilen der Welt geworden. In dieser Arbeit, basierend auf einem neu entwickelten Geografische Informationssysteme (GIS) gitterbasierten 3D deterministischen Modell und mit der Böschung als Untersuchungsobjekt wird die Erdrutschgefahr durch den Index des 3D-Sicherheitsfaktors kartografiert. Unter der Annahme, dass der erste Rutsch der untere Teil eines Ellipsoiden ist, wird die 3D kritische Schlupfoberfläche in der 3D-Böschungsstabilitätsanalyse mit einer Minimierung des 3D-Sicherheitsfaktors mit der Monte Carlo Zufallssimulation erhalten. Die Fehlerwahrscheinlichkeit des Erdrutschs wird mit einer Annäherungsmethode berechnet, bei der die Verteilungen von f,c und dem 3D-Sicherheitsfaktor als innerhalb normaler Verteilungen angenommen werden. Die Beurteilung der Erdbeben-ausgelösten Erdrutschgefahr wird mit der dynamischen Verdrängungsanalyse mit dem Index der Newmark-Verdrängung gearbeitet. Alle Berechnungen werden mit einem Berechnungssystem mit der Bezeichnung 3DSLOPEGIS ausgeführt, bei dem eine GIS-Komponente zum Erfüllen der GIS räumlichen Analysefunktion verwendet wird. Neben der Ergebnissen des 3D-Sicherheitsfaktors und der Wahrscheinlichkeit kann der mögliche Erdrutschkörper und der Umfang dreidimensional quantitativ identifiziert werden.

Jan 1, 2003

By Eleonora Di Mario, Colin B. Turnbull, Matthew G. Mills, Chengbin Miao, Wilhelm S. Degen

"In the past decade, the ‘zero-dredge’ philosophy has become the preferred option for the formation of marine seawalls and reclamations, compared to the partially or fully dredged options, as this solution presents several environmental advantages. Recent relevant project experience is presented herein in order to highlight key design principles and construction issues central to the successful construction and performance of a sloping rubble seawall founded on soft soil improved by stone columns. If designed and installed with proper quality control, correct treatment intensity and sensible construction staging, stone columns are a safe and cost effective method for seawall foundations. This paper provides guidelines with regards to the design, construction and quality control for the correct implementation of stone columns as a foundation element for sloping rubble marine seawalls.INTRODUCTIONBenefits of sloping marine seawalls founded on stone columnsTo suit the current environmental requirements in Hong Kong, recent projects are tending to favour zero-dredge solutions, such as the Hong Kong Boundary Crossing Facility and the forthcoming Three-Runway System. The installation of stone columns allows the underlying deposits, generally consisting of very soft to soft clay and silt (soft soil), to improve in strength to the extent that the seawall can be directly placed on the seabed. This negates the need to dredge the soft soil and, therefore, this ground improvement technique represents an ideal solution for zero-dredge projects.Stone columns can also provide several other beneficial effects, including: accelerated drainage, reduced settlement, increased slope stability and soil reinforcement in the event of an earthquake. Stone columns, in contrast to competing cementitious methods, are a very ductile foundation method. This ductile behaviour is part of the design concept of stone columns in soft soil. Past projects located in Hong Kong and elsewhere, with an improved soft soil layer thickness of over 15m, have shown that stone columns can remain fully functional in terms of both drainage and horizontal reinforcement, even after settlements of over 3m and lateral displacements of up to 1m have occurred."

Jan 1, 2017