Search Documents

By T. O. Hagan

A simulated rockburst experiment was conducted underground at a deep level gold mine. This was done by means of a large explosion detonated in solid rock close to a tunnel sidewall. The resultant shake-out damage is typical of that associated with a small seismic event in close proximity to a tunnel that is subjected to the estimated field stress, as in this case, of 50 MPa. The experiment involved: ?the design of a blast to mimic a seismic source ?seismic monitoring using a dense seismic array ?high speed video filming ?a study of rock mass conditions (fractures, joints, rock strength etc.) before and after the simulation using mapping and ground penetrating radar ?special investigations to evaluate the mechanism and the magnitude of the damage ?a study of support behaviour under excessive dynamic loading.

Jan 1, 2001

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By M Scoble, E Rubio

The re-engineering of manufacturing production systems has demonstrated the benefits from using production information for optimising processes. This paper explores the techniques and issues in the acquisition and analysis of mine production data for tactical decision making in production control. The use of information and operations management tools is presented in the context of block caving studies, with particular focus on the relationship between secondary breaking and LHD production performance.

Jan 1, 2000

The ability to optimise a concentrator from mill feed to final products requires a simulator which integrates comminution, classification and separation modelling. In order to model this range of processes, such a simulator must handle a variety of information about the ore. The AMIRA P9 project has developed a whole-of-concentrator simulation capability which brings together a texture-based model of mineral liberation, quantitative X-ray micro-tomography analysis to measure the inputs required by this model, and a multi-component simulator software framework. In the context of this approach, the term ?multi-component? implies the ability of the simulation to handle many particle properties simultaneously; for example size, composition, density, floatability etc. The simulation software framework provides the means to manage the flow of data around a circuit flowsheet, allowing each process model to access the information relevant to that particular model. A case study based on plant data from a gold-bearing pyrite concentrator is used to demonstrate the capabilities of the multi-component approach in simulating circuits which contain comminution and separation processes.

Feb 27, 2013

By P. Ritsopoulos, A. J. Dentsoras

The objective of this paper is the development of a reliable simulation model for the operation and production capacity of an aggregates quarry. Based on this model, a computer program is introduced that provides the final production outputs according to the defined material gradation and machinery characteristics. The program takes into consideration all operational parameters that may be introduced by the user through the whole machinery network. As a result, all production parameters are properly updated. The structured simulation program can help detect production inefficiencies that result from design ineffectiveness. Additionally, the program can be used for the generation of alternative scenarios for future modifications of a plant's configuration. Finally, a designer can use it as a tool for obtaining optimum solutions concerning newly designed quarries. As a case study, a quarry operating at Heraklion, Crete, was examined. The application of the program to the plant produced a complete image of the quarry's input/output characteristics, along with some suggestions for improvements on certain production processes.

Jan 1, 1998

By D. Brunner, G. R. Baiden, H. J. Yazici

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By D. Brunner

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By E Lima, D Gregory, C Faria, A Lapworth

Open pit mine enterprises are complex systems that depend on multiple parameters such as mineral grade distribution, geotechnical characteristics, economic conditions and engineering requirements, all of which vary in time and space with a different degree of uncertainty. The unpredictable nature of these inputs imposes a risk to mine owners and shareholders which in the worst case can lead to highly undesirable financial outcomes.Desktop studies commonly examine a set of scenarios based on adjusting variables such as commodity prices, mining costs, processing costs, and metal recoveries to understand their relative impact on the economics of a project. It is less common to systematically explore and simulate hundreds of alternative physical designs to understand and compare the financial risk associated with one or more mining projects.This paper presents a risk assessment tool set and methodology that uses web based cloud computing to enable multiple simulations of mine designs to be rapidly and efficiently executed. The methodology includes generating random sets of prices and costs values within their respective probability distributions. Pit designs are then created to maximise the profit for each set of input variables. Various approaches to analysing the results are discussed. Use of the same high performance computing environment for understanding the financial risk associated with the variability of the underlying geological resource model is also discussed, with provided examples using case studies from two of the major mineral producers.CITATION:Lima, E, Gregory, D, Lapworth, A and Faria, C, 2014. Simulating extraction shapes to understand financial risk using high performance computing, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A Turichshev

The synthetic rock mass (SRM) approach for modelling jointed and veined rock has been at the forefront of caving geomechanics research for years. A well-constructed and calibrated SRM model can capture the full rock behaviour at a macroscopic scale. Traditionally, SRM technology employed bonded particle models (BPM) due to their ability to model rock’s response to loading without prior specification of behaviour. The SRM modelling process requires the BPM to simulate intact rock and the subsequent introduction of fractures or veins by changing bonding characteristics between the particles. However, bonded particle materials have difficulty reproducing both the compressive and tensile strengths of intact rock. This and other limitations of BPM have been the driving force in exploring the potential of grain-based (2D) and bonded block (3D) models (BBM).This paper reports on recent work exploring the applicability of both BPMs and BBMs in 3D to the modelling of intact rock. The advantages and limitations of both BPMs and BBMs are addressed based on the results of numerical simulations using the PFC3D and 3DEC distinct element codes. The preliminary results suggest that BBMs are better suited for simulating intact rock behaviour than BPMs. Ongoing work aims to better qualify the applicability of BBMs under different conditions. This has significant implications for our understanding of rock mass behaviour in a caving environment.CITATION:Turichshev, A and Hadjigeorgiou, J, 2016. Simulating intact rock behaviour using bonded particle and bonded block models, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 453–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S Szylkarski, D N. Graham

In mining, water management is an operational necessity, requiring planning and detailed engineering, as well as risk assessment. Yet, the hydrology of streams and aquifers typically extends well beyond the boundaries of mine operations and intersect with environmental and social values. Mine managers often plan, design and assess the impact of water management activities (such as dewatering, excess water disposal and flood management) with a mine site or process specific focus. The challenge is that the impacts are spatial, long-term and complex – and may be cumulative across multiple mine sites. Further, there is usually little consideration of the feedbacks and interactions between surface water, groundwater and catchment hydrology. Failure to understand these processes can lead to poor decisions and increased costs. This presentation outlines an approach to simulating integrated hydrology in mining catchments that addresses the shortcomings of traditional modelling techniques.CITATION:Graham, D N and Szylkarski, S, 2016. Simulating integrated hydrology in mining catchments from planning to closure, in Proceedings Life-of-Mine 2016 Conference, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By A Karrech, A Hasan

This paper presents the numerical simulation of mine backfilling in underground stopes using three-dimensional discrete element modelling (DEM). The simulation predicts the forces exerted at the stope base and barricade with respect to time under free drained conditions. The results of the numerical simulation are validated using basic analytical solutions and advanced experimental tests involving a geotechnical centrifuge system. Overall, a good agreement between the present numerical simulations and the existing experimental and analytical results was found. The present model suggests that DEM is a promising computational tool to predict barricade pressure in underground mine stopes.CITATION:Hasan, A and Karrech, A, 2014. Simulating mine backfill in a fully drained condition using discrete element modelling, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 117–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

A computer programming language known as GPSS is described and possible applications for the mining engineer are presented. The language is continually being upgraded with improved versions appearing about every three years. The tremendous power of the language is considered by comparing it with standard engineering programming languages, such as Fortran or Basic. Sample problems that can be solved using the language are indicated. The advantages and disadvantages of the languages are also discussed.

Jan 1, 1987

By H. S. George

A method of illumination that enhances the value of microscopic study of opaque materials, as in metallography. By simulating natural lighting, structures. That possess relief are given a natural appearance. An example is included of the revelation of a hitherto invisible microconstituent. Erroneous interpretation is avoided. For example, etching figures in ferrite, heretofore considered to be pits, are revealed as pyramids, standing in bas-relief. Suggestions on technique are given, for, while the method is obvious, practice and attention to detail are requisite. ON one occasion when it seemed desirable to reveal under the microscope not only the metallic structure of an alloy, but certain small non-metallic inclusions, that are ordinarily obliterated by etching, it was discovered that, by partly eclipsing the illuminating pencil of light rays, the residual light was thrown on the object from one side and the structure was brought out in relief. At the same time, the non-metallic inclusions were retained in clear view. In this first demonstration of lighting obliquely through the objective a card was thrust part way into the light beam between the arc iris, and the light filter; the shadow of the card on the filter served to locate its position. Next several stiff-paper disks of various diameters were mounted on flexible wires some plasticine on the other end of the wires made it easy to adjust and maintain a disk at any desired position in the light beam. To facilitate manipulation, an assortment of disks, was mounted on a wheel, as shown in Fig. 1. The purpose of partly eclipsing the light beam was discussed in an earlier paper.1 There it was pointed out that the usual methods of illuminating opaque objects for microscopic examination lend an, un-natural appearance to, the view, while the new method, which has been termed conical illumination, revels the true relationship of constituents by simulating natural lighting.

Jan 3, 1924

By D. F. Malan, J. C. Esterhuyse

In this study we explore the use of a novel numerical modelling approach to study the effect of pillar reinforcement on pillar stability. Case studies in the literature indicate that tendons, strapping of the pillars, and shotcrete or thin spray-on liners are commonly used to reinforce pillars. No clear methodology exists to select the type of support or to design the capacity of the support required, however. This has led to ongoing collapses in some mines in spite of heavy support being used to reinforce unstable pillars. A limit equilibrium model with confinement on the edge of the pillar was used to simulate the interaction of the support with the failing pillar. The model correctly predicts that an increase in confinement will lead to a decrease in the extent of pillar failure. As the displacement discontinuity boundary element method allows for the efficient solution of largescale bord-and-pillar layouts, the effect of pillar confinement can now be studied on a mine-wide scale. Accurate calibration of the limit equilibrium model is, however, required before this method can be used for the design of effective pillar support.

May 3, 2023

By Guiseppe Bonifazi

This work applies the definition of "separation function" already introduced in the paper presented at the XVIII IMPC. This 'function" (defined for a certain size distribution after comminution of an ore) refers to the recovery distribution of a mineralogical species in a product made up of all the particles having at least a given content of that species. Many tests would be required to determine the liberation function for each mineralogical species, particularly for complex ores. Several stages of comminution would need to be examined and the mineralogical composition of the particles of each grain size class would need to be analyzed for each process step. A quick and dirty method is shown for obtaining the "separation function". It is based on the processing of data from topological maps of polished and/or thin representative sections of ore. By superimposing grids of different sizes over these maps and with appropriate combinations of mesh sizes, it is possible to simulate the grain size distributions linked to different stages of comminution and then evaluate the mineralogical composition of each grain. The procedure is carried out full automatically and can simulate a complete treatment circuit, imposing cut-off grades for the products at each separation phase. It is also possible to predict the results of treatment processes that involve grinding phases. The procedure has been successfully applied to complex ores containing several useful components.

Jan 1, 1995

By Liming Yuan

[ ]

Jan 1, 2009

By John Jiang, Yeonuk Choi, Olivia Wang, Gus Van Weert

"As part of a general review of processing double refractory ores through Barrick Gold's autoclaves/CIL facility at Goldstrike, Nevada, blanking the gold cyanide adsorbing native carbon in the ore with hard (m.p. >55°C) paraffin wax was proposed. To avoid interference from other ore constituents in the exploratory testwork, commercial activated carbon was substituted for native carbon in the ore to establish the best conditions for de-activation of carbon with molten wax.IntroductionDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including the Goldstrike deposit, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (POX). It is the latter route to which this paper refers.The second barrier refers more correctly to gold recovery. Gold may be extracted from the autoclave oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This behaviour is used advantageously on a large scale by gold millers, who use man made activated carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold after autoclave oxidation."

Jan 1, 2012

"Load-haul-dump machines (LHDs) are typically used in underground metal mining operations. Delays or inappropriate use of LHDs can result in production loss. Optimized LHD use is especially crucial in larger mines because longer travel distances increase heat, dust, and gas emissions, which in turn increase ventilation costs. This study, conducted at an existing Swedish sublevel cave underground mine, used discrete event simulation and the AutoMod™ DES tool to determine the ventilation costs related to using too many diesel LHDs in a production area with reduced ore pass availability. When fewer ore passes are available, ventilation costs related to operating LHDs in the production area were found to increase by as much as 200, 224, and 306% for one, three, and six LHDs in operation, respectively. ¦ KEYWORDS Discrete event simulation (DES), Loading operations, Production rate, Ventilation costs RÉSUMÉ Dans les exploitations souterraines d’extraction des métaux, on utilise généralement des chargeurs-transporteurs (LHD, de l’anglais Load-haul-dump machines). Les retards ou l’utilisation abusive des LHD peuvent entraîner une perte de production. L’utilisation optimisée des LHD est particulièrement importante dans les grandes mines en raison des longues distances parcourues, lesquelles augmentent la chaleur, la poussière et les émissions de gaz qui, à leur tour, décuplent les coûts de l’aérage. Cette étude, menée en Suède dans une mine souterraine utilisant la méthode d’exploitation en sous étages avec foudroyage, s’est basée sur la simulation à événements discrets (SED) et l’outil de SED AutoMod™ pour déterminer les coûts de l’aérage liés à l’utilisation d’un nombre trop élevé de LHD alimentés au diesel dans la zone de production, avec une disponibilité réduite de la cheminée à minerai. Lorsque les mines disposent de moins de cheminées à minerai, l’étude montre que les coûts de l’aérage liés à l’exploitation des LHD dans la zone de production augmentent respectivement de 200, 224 et 306 % pour un, trois et six LHD en fonctionnement. ¦ MOTS CLÉS coûts de l’aérage, opérations de chargement, simulation à événements discrets (SED), taux de productionINTRODUCTION Transporting material from the mine face to the dumping location requires flexible loading and hauling equipment that is able to cope with sharp curves and a complex mining environment. Load-haul-dump machines (LHDs) are designed for such an environment. Models are available to suit specific features of the working environment such as small, large, or narrow open stopes (Atlas Copco Rock Drills AB, 2007). When carrying a full load, haulage speed is higher for LHDs than for front-end loaders with the same engine size. Also, payloads are approximately 50% higher for LHDs than for front-end loaders (Atlas Copco Rock Drills AB, 2007). LHDs are capable of climbing steep (Bloss, Harvey, Grant, & Routley, 2011). The haulage distance between stope and ore pass is usually between 50 m and 400 m. LHDs are efficient for tramming distances up to 200 m (Bloss et al., 2011), whereas when loading trucks, the LHDs work efficiently when the distance is less than 100 m (Atlas Copco Rock Drills AB, 2007). The largest diesel-powered LHDs, with drive motors of up to 350 kW, can handle a payload of 21 t (Wennmohs, 2014). Most mining equipment runs on diesel fuel, which provides flexibility, high durability, and high efficiency (Pronk, Coble, & Stewart, 2009); however, other alternatives such as electric, hybrid diesel/electric, or hydrogen fuel cell machines are increasingly being developed and used. This change is due to diesel-powered machines accounting for a significant portion of the ventilation costs in the mine (Chadwick, 2008; Paraszczak, Laflamme, & Fytas, 2013). Currently, as part of the European sustainable intelligent mining systems (SIMS) project, Epiroc AB is planning to demonstrate technology for a diesel-free underground mine at Agnico Eagle’s Kittlä mine in Finland using"

Jan 1, 2019