Search Documents

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Knowing shear mechanism of discontinuities under monotonic and cyclic loading conditions is a key factor in stability analysis of rock slopes and rock foundations. In this paper, the effect of cyclic loads on the shear mechanism of joint asperities is described. For this purpose, a fresh tension-split joint from a granite block was used as a reference and thirty five mortar replicas were fabricated. Cyclic shear tests were conducted on replicas under low values of constant normal load (CNL) using a servo-controlled loading system. Tests were performed in two consecutive steps; load-controlled and then displacementcontrolled. In the load controlled part, after initial increase of shear stress to 0.25 MPa, the test was stopped for 2 minutes, then increased to 0.5 MPa, and finally decreased to 0.25 MPa. This process was repeated ten times. At the end, the test was continued up to 10 mm shear displacement under displacement-controlled loading in order to pass the peak shear strength and reach the residual strength. Characterizing joint surface and modeling of involved asperities during the tests was undertaken using a Matlab code developed with new mathematical expressions. The algorithm used in the code is based on three-dimensional coordinates of the scanned joints’ surfaces before and after the test. It was found that a high percentage of degradation happens during the first cycle of loading and during the other cycles, degradation occurs gradually. While comparing tests conducted in monotonic and cyclic loading conditions, it was observed that under low number of cycles, the pronounced mechanism is consolidation of the joint surfaces. This consolidation increases contact areas and, therefore, shear strength parameters.

Jan 1, 2015

By Mark Larson, Steve Iverson, Brian G. White

The authors hypothesize that excavation-induced extension fractures are caused by elastic shearing displacement that in turn causes tension oblique to a propagating shear zone. Such extension is manifested as tension on scales larger than that of microcracks. En echelon fracture patterns are a common result. FLAC modeling confirmed that localized tension is created near the corners of mine openings. In the model, tension was concentrated at the leading edge of a simulated fracture in a pattern that could promote the formation of an en echelon fracture. Particle Flow Code models confirm progressive formation of en echelon tensile failures with distance from an opening. The elastic displacements and the resulting fractures facilitate reduction in applied load at the expense of shear deformation and lateral dilation. Understanding the mechanics of fracture and deformation is vital for designing more effective ground support practices, a major objective of ground control research being conducted at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health.

By Saman Khaleghparast, Naj Aziz, Jan Nemcik, Guanyu Yang

"More than 25 years of uninterrupted research on ground support technology for underground mines has been undertaken at the University of Wollongong. This research has resulted in significant findings on tendon characteristics and strength properties. The paper focuses on the development of the fourth generation of cylindrically shaped shear test apparatus for assessing tendon performance in shear. This shear apparatus is known as the MK-IV Double Shear Box or Naj Aziz Double Shear Box (NADSB), and is based on the experience gained from the development of previous versions of rectangular double shear boxes. The new NADSB is circular in shape and is fitted with a truss system, which permits friction free shear testing of tendons across joint planes. A series of double shear tests were carried out on a number of cable bolts commonly used in Australian mines, both plain and indented wires, under varied pretension loads. The results were compared with similar test results using rectangular shaped double shear apparatus, with and without friction across joint faces. The significance of wire surface roughness and increased initial pretension loads are discussed and conclusions made, suggesting that indented wires are inferior in shear compared with plain cable bolts. The general test procedure of the NADSB is described and different concrete reinforcement techniques are reported. The influence of external and internal confinement of the concrete medium blocks in a circular double shear box contributed to consistent test results with a minimum of lateral and axial cracks occurring in the host medium.INTRODUCTIONThe use of long tendon ground support elements (cable bolts) is now a common practice in modern underground coal mines, hard rock mines, tunnels and other underground structures. Due to their material properties cable bolts contribute significantly to the overall ground reinforcement provided by a support system. Cable properties in tension and shear are in many cases vital to maintaining a safe and productive underground environment. Accordingly, tension and shear properties must be assessed accurately using both valid and reliable methods.Load transfer property testing of tendons has been studied over several decades with much of the early research focused on the pull and shear testing of solid rock bolts and hollow bolts (like Swellex and split set tube bolts), as these elements were used extensively at this time. It was not until the 1970’s that the use of cables for ground reinforcement developed, and as such highlighted the need to extend load transfer property testing to include shear strength of cable bolts. Initially, the discarded hoisting ropes were used for ground support in metal mines, particularly in stopping wall support and then late in 1980’s cable tendons began to use in coal mines."

Jan 1, 2019

By J. J. Jonas, G. R. Stewart, N. Pokutylowicz, S. Yue, R. Varano, A. Elwazri

Differing thermal histories in and around a weld can lead to differences in grain size, phase composition and morphology of precipitates; mechanical properties will vary accordingly. Hardness testing gives limited information and the machining and testing of tensile and/or impact specimens that would reveal these variations (which may occur over very small distances) is not practical. Therefore, in this investigation, shear punch testing was applied to measure the variation in the room temperature mechanical properties of a welded pipeline steel.

Jan 1, 2005

By Charles J. Haas

The effectiveness of rock bolts in resisting shear displacement along preexisting fracture surfaces or slip planes was determined in the laboratory with full-scale bolts and large-scale shear test equipment. The system variables were the type of bolt, orientation of bolt relative to shear surface, and normal pressure on the interface. Results showed that, in general, both conventional bolts and resin- grouted reinforcing bars significantly increase the shear resistance along a fracture or bedding plane when the average normal compressive stress on the plane is in the order of 25 psi and when the bolt is oriented such that it tends to lengthen as the shear progresses. An increase in shear resistance is also noted at the higher normal pressure of 250 psi; however, the increase is small compared to the corresponding shear resistance without a bolt. Conventional bolts oriented such that they lose tension as shear displacement occurs added no shear resistance since the tension drops to zero at very small shear displacements.

Jan 1, 1977

By William G. Pariseau

The extraction ratio approach to pillar design in flat seams is based on a mathematically exact analysis that is a reasonable physical approximation to room-and-pillar layouts in many instances. The essentials of the approach are reviewed and then mathematically approximate formulas for pillar design in inclined seams of arbitrary dip are proposed. Detailed numerical analysis of stress about a typical 5 entry, 4 pillar panel at dips of 0, 15, 30, 45, 60, 75 and 90 degrees at low and high extraction ratios show that the proposed inclined seam extraction ratio formulas for pillar normal and shear stresses, although conservative, have an accuracy quite adequate for engineering purposes. Appropriate pillar safety factors for compressive and shear failure and a safety criterion for overturning are specified.

Jan 1, 1982

By L. P. Srivastava

Rock bolts have been used since long to enhance the shear strength response of jointed rocks in civil and mining engineering structures. However, the assessment of strength response of a rock mass reinforced with rock bolts remains an unresolved problem till date. In the present article, an attempt has been made to study, through physical model tests, the shear strength enhancement of a blocky mass due to provision of passive rock bolts. Direct shear tests were conducted on large specimens of size 750 mm x 750 mm x 900 mm of rock mass under a normal stress varying from 0 to 2.0 MPa. Concrete was used as a model material to simulate intact rock and, elemental blocks of size 150 mm x 150 mm x 150 mm were used to form the mass specimens. Steel bolts of 6 mm diameter with 2 mm thick grout were used to reinforce the mass. Three different configurations of bolts were adopted. Observations were made on shear stress, horizontal shear displacement, and dilation during the tests. Effect of normal stress and reinforcement on peak shear stress and shear stiffness was studied. It is observed that the rock bolts enhance the shear strength of the mass by preventing sliding along the shearing plane, and by inducing additional normal stress due to tension mobilized in the bolts. The rock mass, therefore, becomes stronger due to the high degree of interlocking produced by the bolts. Shear strength of the mass increases with increasing numbers of bolts. In the case of reinforced mass, the enhancement in shear strength due to provision of bolts decreases with an increase in normal stress. The provision of bolts improves the cohesion of joints substantially. The effect on friction angle is low. The shear strength enhancement depends on the area of the bolts, spacing of the joints, spacing between the bolts and the cohesion of the intact material. A correlation has been established using which the enhancement in shear strength due to the provision of bolts can be assessed.

Jan 1, 2015

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By Navid Bahrani

Overview ? Case history of footwall slab failure ? Procedure used to build a finite element model ?? Pre- and post- mining topography ?? Slab geometry ?? Excavation stages ?? Input parameters ? Finite element modelling results ?? Unloading-induced displacements (magnitudes & directions) ?? Calibration of overall model using measured prism displacements ?? Shear stresses and displacements along the base of slab ?? Factors of safety at different stages ?? Effectiveness of rock bolts ?? Staged or unstaged model? ? Conclusion

May 1, 2008

By N. Bahrani

Photogrammetry surveys were used to document a footwall slab failure that occurred at a surface coal mine located on the eastern slope of the Rocky Mountains. Photographs taken before and after the failure provided the pre- and post-failure geometry of the slope and the failed slab. A 2D finite element model was constructed using slope profiles. The model contained joint elements that represented the bedding surface upon which the slab slid and the model was used to analyze the footwall slope. The in situ stresses, rock properties and the bedding surface shear strength and stiffness properties are discussed. The process of mining out a valley and exposing a highwall was modelled. As expected, elastic valley rebound occurred in the model, but shear stress and shear displacement reversals along the slip surface were also observed. The modelling results provided new insight into shear strength degradation that occurs when the pit floor approaches and then passes a specific point in the highwall.

Jan 1, 2009

Large-scale shear apparatus is designed to investigate the shear hehaviour of simulated soft rock joints under constant normal stifmess condition. Regular saw-teeth profiles having inclinations between 9.5" and 26.5" have been tested. The strength envelope based on these test results indicates that predictions made by Panon (1966) are accurate for the lower asperity angles. However, for higher asperity angles, Patton&apos;s model overestimates the shear strength especially in the low to medium normal stress range. In contrast, while Barton&apos;s model (1973) is realistic for Constant Normal Load (CNL) condition, it seems to be inappropriate for modelling the shear behaviour of soft joints under Constant Normal Stiffness (CNS) condition. An empirical strength envelope for the prediction of peak shear strength of joints is proposed in this study to account for the change in normal stress and surface degradation during CNS shearing.

Jan 1, 1997

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By Nick Barton

Simple methods for estimating the shear strength of rock joints and waste rock are reviewed. For the case of rock joints, the methods are based on a quantitative characterization of the joint roughness and the joint wall strength. Size-effects are found to reduce the peak strength of large joint samples to values below the ultimate or so-called "residual" values measured in the laboratory. Tilt tests and surface profiling on natural size blocks within the jointed rock mass are recommended for obtaining scale-free properties. The joint parameters obtained can be used to model complete strength-displacement-dilation behavior if this level of input is required. Large scale tilt tests can be performed with advantage on both rock joints and waste rock. The behavior of these two materials is surprisingly similar. Both are influenced by the size-effects on the compression strength of the rock, and both have similar log-linear relationships between effective normal stress and the peak drained friction angles. The resulting high values of friction near the toe or close to a slope face in either material can be misleading.

Jan 1, 1983

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J. P. Rajot, H. Mouzannar, M. Bost

"The design of rock foundations may need to evaluate shear strength of rock-concrete interface by performing laboratory direct shear tests. A series of tests were carried out on specimens for different values of the spacing free of encapsulating material about the shear plane and different values of normal stress. Different kinds of failure were observed and not necessarily at the rock-concrete interface. The spacing free of encapsulating material appeared to be of significant influence on the test results. A mechanical analysis is presented which illustrate the influence of the loading conditions in the direct shear box on the failure mechanism. INTRODUCTIONThe design of rock foundations subjected to significant lateral loads requires defining the value of the shear strength of the interface between rock and cast in place concrete. Verifying the stability against sliding of strip footings subjected to inclined loads (SETRA, 2009) or concrete gravity dams (CFBR, 2013) are common examples where design modelling approaches imply the shear strength, sometimes the deformation behavior, of the rock-concrete interface, more or less assumed as a failure plane.Defining the behavior of rock-concrete interfaces relates to tribology. Many studies have been conducted to improve the representation of this behavior (e.g., Johnston & Lam, 1989; Kodikara & Johnston, 1994; Gu, Seidel & Haberfield, 2003; Saiang, Malmgren & Nordlund , 2005; Fishman, 2008; Eltervaag, 2013; Gutierrez, 2013), raising many questions. The behavior appeared to be influenced by many factors such as the geometry of the interface which is not planar, the roughness of the natural rock, the rock mineralogy and the concrete formulation. In addition, the study of the shear strength of rock-concrete interfaces involves considering the two different deformation behaviors of both rock and concrete. Finally, the observed failure mechanism is strongly influenced by the initial cohesion due to adhesion between the two materials when concrete is directly cast onto rock."

Jan 1, 2015

By Naj Aziz, Peter Craig

"Double shearing tests were carried out on the 28 mm (1 in) hollow strand Jennmar TG cable bolt to gain a better understanding of the shearing behavior of the cable. The first test was limited to a 50 mm (2 in) travel on the testing machine and produced a shear load of 900 kN (92 t) at the maximum 50 mm (2 in) displacement. The axial load generated on the cable bolt was 238 kN (24.3 t). In the second test, the machine travel was increased to 75 mm (3 in), and first strand failure of the cable, due to shear loading, occurred at 1,354 kN (138 t) vertical load at a vertical displacement of 59 mm (2.3 in). The cable axial load was in the order of 385 kN (39.3 t). Analysis of the failure mode and loads achieved showed that the cable strands bent and the concrete crushed along the shear plane; the shear loading across the concrete and grouted cable then reached the tensile strength of the steel wires.INTRODUCTIONCable bolts were introduced to the mining industry around 1970, initially to surface mining and underground metalliferous mining and then to coal mining in the early 1980s, mainly for roadway reinforcement as a secondary means of support. Cable bolts have since been used as both primary and secondary supports. As primary support, Fuller et al. (1994) described the application of cable bolts, known as FLEXIBOLT, for strata reinforcement in both Angus Place and Ellalong Collieries, in New South Wales (NSW), Australia. As secondary support, cable bolts have also been used as cable trusses, which act to support the immediate roof in a sling-like manner (Fabjanczyk and Tarrant, 1988; Fuller, et al., 1991; O'Grady and Fuller, 1992), and for reinforcement at higher stratification and beyond the rebar bolt length, mainly for anchoring lower strata layers immediately above the coal seam to the higher, competent bedding formation above. Initially cable bolt anchorage was by cementatious grouting and, since the 1990s, by chemical resin. The dominant type of cable bolts used for secondary support in Australian underground coal mines are 588 kN (60 t) capacity cables which are point anchored, pre-tensioned and post-grouted. Point anchored refers to a cable resin anchor. The cables are tensioned on the resin anchor; then the same cable is grouted by cementatious grout pumped to ·fin the annular gap around the cable from the collar of the hole to the resin anchor. Bulbs are located within the resin anchor section for mixing of the resin chemical components and efficient anchorage. The installation of these typically 8 m long cable bolts involves a lot of manual handling of the cables, lifting of heavy hydraulic tensioners, and exposure to resin grouts. Table 1 shows the specification of various cable bolts currently marketed and installed in Australian underground coal mines."

Jan 1, 2010

By James R. Fahy, Lawrence A. Hansen, J. David Deatherage

A laboratory testing program was con- ducted to investigate the shear strength along specific soil-liner interfaces for five types of liners of varying thicknesses. Results indicated a bilinear relationship between shear stress and applied normal stresses ranging from 276 to 1000 pKa (40 to 145 psi). Friction angles along the soil- liner interface below the break point normal stress (7.5 to 19 degrees) were lower than those recorded above the break point normal stress (14.5 to 39 degrees ).

Jan 1, 1987

By Peter J. Nicholson

Recognition of the liquefaction susceptibility of dam embankments has been heightened since the San Fernando Dam near failure incident in 1971. Both the downstream and upstream slopes of dams can be at risk for slope failure that can lead to breaching of the dam during or after a seismic event. Many dams have been remediated by various means such as the installation of stone columns or by excavation and replacement of the liquefaction susceptible material. Recent engineering and technology advances in equipment and materials has shown that construction of shear walls to the appropriate depths and at the right center to center spacing may be an economical alternative to the more traditional methods. Recently, the downstream embankments of at least 4 dams, from South Carolina to California, have been, or in the process of being remediated by the use of shear walls. The method of installation has been either multi-axis Cement Deep Soil Mixing walls or walls constructed by the use of trench excavation under self-hardening slurry. Four case histories of dam remediation are discussed, three by multi-axis paddle auger CDSM equipment one with the use of self hardening slurry trenches.

Jan 1, 2008

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By H. Yilmaz

A testing method for assessing the shear-bond strength of thin spray-on liner (TSL) on rock substrate was developed at Wits University Rock Mechanics Laboratories. The gap between a 20 mm thick steel ring and a rock core is filled with TSL along the depth of the ring. After the curing of the TSL for a predetermined period, the sample is placed on a base, which offers support to the steel ring and the TSL but not to the rock core. A compressive load is applied on the rock core displacing the core on TSL contact and punching it towards the void in the support base. Shear-bond strengths for different TSL products as well as shotcrete were measured. This paper describes the test set-up and points out the important aspects and procedures during sample preparation and test execution. The test results are also presented and discussed.

Jan 1, 2007