Search Documents

Records over the past ten years indicate that there is potential for serious multiple accidents due to engulfing associated with rockpasses. Significant attention is not usually given to the design of rockpasses, with the implication that mistakes leading to poor performance of the passes are often repeated. This paper outlines general guidelines for the design, support, operation and rehabilitation of rockpasses based on information obtained from the limited amount of literature on the subject.

Jan 1, 2005

By Samir N. Shoukry, Mourad Y. Riad, Gergis W. William

"Setting of concrete material is defined as the transitional period between states of true fluidity and true rigidity. Initial and final setting times are measured in the laboratory on the mortar sieved from the mix in a controlled environment where temperature and moisture values are constant. On the other hand, field applications are held in outdoor environments where environmental variations have direct impact on setting time values. In this study, initial setting time of class K concrete, usually used for bridge decks and concrete pavements, are investigated highlighting discrepancies between laboratory and field measurements. 72 mixes have been cast in variable environments and collected data from concrete mixes and the ambient conditions are reported. In light of the collected data, the effects of variable setting times on early age cracking of concrete material are studied and means to minimize such cracks are presented.BackgroundSetting of concrete material is defined as the transitional period between states of true fluidity and true rigidity [1]. Continuous hydration of the cement within the matrix transfers the mix from a state of setting to hardening. Initial and final Setting times are measured in a laboratory setting following ASTM C 403 specifications. Initial setting approximates the time at which the cement paste can no longer be plastic under compaction (or can be handled in a proper fashion), while the final setting approximates the time at which hardening occurs. The standard test described in ASTM C 403 is conducted on the mortar sieved from the mix (paste passing from 4.75 mm sieve opening). Initial and final settings are described as the elapsed time after the initial contact of water and cement till the mortar reaches a penetration resistances of 3.5 MPa (500 psi), and 27.6 MPa (4000 psi) respectively."

Jan 1, 2012

By R. K. Young

Producing a sound plant design for a major project requires hundreds of engineers and many drawings. Economical accomplishment of this task is based upon careful and orderly organization of the design team so that at all times there is a complete and workable staff but at no time a surplus of costly talent. This paper will describe the various stages in the development of plant design which normally follow the laboratory and pilot plant investigations discussed in other papers today. An outline of the procedures used in the assembling of a project design group, within an established engineering organization will be presented. Actual procedures may vary according to the size and character of the plant, the special requirements of the owner, and the make-up of the engineering organization performing the design, but most of the points covered will be found to be basic to any plant design project.

Jan 1, 1960

The Yanacocha district hosts the largest and most significant acid-sulphate, high-sulphidation deposits in Per· with total production, reserves and resources of over 27 million ounces of gold. Several other smaller high-sulphidation systems are also recognised in the Cajamarca region including La Zanja, Sipßn, Tantahuatay, and San Nicolas. These each have reserves/resources of between 640 000 and 800 000 ounces of gold. Gold deposits in the Yanacocha district are hosted in an extensive volcanic field. Flow domes have intruded precursor pyroclastic rocks and flows that are interpreted as part of an earlier intermediate multi-vent volcanic complex. The larger, contiguous Yanacocha Norte - Sur and Encajon gold deposits are spatially associated with late-stage diatreme breccias. At La Zanja extensive acid-sulphate alteration is associated with the margins of the small San Pedro caldera (6 +4.5 km), nested within the larger, less well-defined La Zanja caldera (19 +24 km). The inner caldera is resurgent with abundant magmatism expressed as several flow dome complexes located on the caldera rim, and shallow level intrusive stocks. Gold mineralisation is associated with a WNW-trending structural corridor that transects the southern margin of the San Pedro caldera. On the eastern side of the La Zanja caldera there are a series of younger andesitic eruptive centres, some associated with acid-sulphate alteration and gold mineralisation. The Sipßn deposit occurs in one such centre with structurally-controlled gold associated with a NE-trending silicified structure developed within a sequence of andesitic tuffs. In conclusion, although a number of high-sulphidation deposits are recognised in northern Per·, their settings and styles of mineralisation are all quite different. Smaller deposits generally have strong and obvious structural controls. In the larger Yanacocha deposits the structural controls are less obvious, and mineralisation is disseminated in porous or strongly fractured and brecciated silica. Erosional levels are probably a significant factor, with disseminated mineralisation at higher levels, and structurally-controlled mineralisation in more deeply eroded deposits.

Jan 1, 1999

By R. Heath Forbes

The route of a new, 4-mile long, electrical transmission line passed through residential neighborhoods and commercial areas of a small town in the South Carolina Coastal Plain. The new line consisted of 54 new poles and a one-mile underground section. Most of the new poles were constructed within 50 ft of existing structures, and in some cases, within 8 ft to 20 ft. A widely-space subsurface exploration consisting of 20 cone penetration test soundings indicated the subsurface conditions along the alignment generally consisted of saturated, loose to medium dense, fine slightly silty to silty sand. The pole foundations consisted of 20 to 30 ft long, prefabricated ?caissons? (essentially an open-end pipe pile with a prefabricated connection system at the top) with diameters of 28 to 56 inches. The steel caissons were installed with vibratory pile hammers. To help prevent damage and defend against possible allegations from nearby property owners, vibration and settlement monitoring was performed during all foundation installation activities. Limited structural condition assessments were also performed before and after foundation installation. For 53 of the 54 foundations, the ground vibrations recorded at distances coincident with the nearest structure locations ranged from 0.05 inches per second to 1.46 inches per second. With consideration of the dominant frequency, the majority of these values were below the commonly used USBM vibration limits. For a foundation installation that was only 8 ft from the nearest structure, a peak particle velocity of 3.06 inches per second was recorded, which exceeded the USBM limits. For all cases, the measured ground surface settlement was negligible (i.e., less than ¾ inch). Several spurious claims alleging vibration-induced damage were made, but the monitoring program provided an adequate defense. One claim involving artwork that fell to the floor during foundation installation at a distance of 8 ft from the house was deemed legitimate.

Jan 1, 2011

By W. Y. Xu

In comparison with shallow foundation, usually higher bearing capacity, smaller average settlement and better stability are the engineering characteristics of pile foundation. Besides, a smaller differential settlement and a lower settlement rate which will converge quickly are more important characteristics. The superstructure of the building with pile foundation may not meet with significant differential settlement. In this paper, settlement records and other data of different kinds of buildings are chosen to illustrate the characteristics of pile foundation. Moreover, some technical problems in connection with foundation engineering solved in consideration of the above mentioned characteristics of pile foundation are also introduced.

Jan 1, 2010

By Wei Tu

A grade separation was required to allow uninterrupted traffic crossing for a busy rail spur and a county road. The grade separation was achieved by creating a 30-foot (9-meter) high embankment that incorporates two multiplate tunnels and allows the passage of a rail spur and an existing county road. The site is located in an abandoned meander channel in the floodplain of the Mississippi River, near Osceola, Arkansas, and is underlain by more than 40 feet (12 meters) of soft clay and interlayered clays, sands and silts. Without soil improvement, the post-construction settlement would exceed 3 feet, slowly crushing the proposed tunnel structure and cutting off the railroad. Preloading, combined with vertical drains, was used to accelerate the consolidation of the underlying soil layers and to reduce the post-construction settlement under working loads. Six settlement plates were installed to monitor the progress of consolidation under surcharge load. The Asaoka observational method and the hyperbolic fitting method were used to analyze the measured settlement data to predict the end of primary settlement. The in-situ consolidation coefficient, ch, was back calculated from the measured settlement data. The stress release caused by the removal of the preloading surcharge load and the tunnel installation was determined using a Plaxis 3-D finite element model. The measured and predicted settlement using Hansbo's analytical solution demonstrated reasonable agreement. Early removal of the surcharge and construction of the tunnel prior to reaching the end of primary settlement was accomplished by analyzing the post-excavation stress reduction achieved via tunnel construction.

Jan 1, 2009

By Ben M. Lewis, Yogesh Prashar

"The East Bay Municipal Utility District (EBMUD) is a major water utility service providing water to over 1.3 million people in the eastern San Francisco Bay Area. EBMUD manages 28 dams at 5 terminal and 23 open-cut reservoirs within a 331-square-mile customer service area. As part of a 2012 update on EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, EBMUD has decided to replace Central Reservoir, a 152.8 milliongallon open cut reservoir, with optimally sized tanks. This paper presents the results of an analytical comparison of various foundation reinforcement solutions for the proposed tanks including: Cement Deep Soil Mixed (CDSM) columns, vibro stone columns, rammed aggregate piers, and lightweight cellular concrete fill. The computational program GeoMat (www.ensoftinc.com) was used to perform simplified soil structure interaction analyses. Settlement estimates were developed for each alternative with the proposed loading and compared to an allowable differential settlement criterion established at 0.3-inches over a 50 foot length. The authors wish to present the importance of considering mat and soil interaction along with various settlement mitigation methods considered for this challenging project.INTRODUCTIONProject BackgroundCentral Reservoir is an operational open-cut reservoir located north of the intersection of 25th Avenue and East 29th Street in Oakland, California. The reservoir is bound by 23rd Avenue to the west, Sheffield Avenue to the east and Interstate Highway 580 to the north. Originally, the Central Reservoir site was a drainage swale incising into weathered bedrock formed from Pleistocene alluvial deposits. The reservoir was first constructed in 1910 by excavating a basin below grade and constructing an embankment dam on the south and cutting/filling the bedrock and alluvial deposits from the drainage swale. The main dam at the Central Reservoir site is also a DSOD (Department of Safety of Dams) jurisdictional dam and as such is regularly monitored by the EBMUD Materials Engineering Section and the California DSOD.In a 2012 update to EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, Central Reservoir was identified as a critical facility that has reached the end of its useful life and must be replaced due to: a failing panel craft lining which contains polychlorinated biphenyls in the interior coating, a roof that does not meet the current seismic code, and reduced operating levels due to potential leakage in the upper portions of the panel craft lining. Furthermore, Central Reservoir is about three times larger than required and is located at a lower elevation than other regional reservoirs in the pressure zone resulting in increased labor-intensive operational challenges and water quality operations.This project presents some challenging geotechnical demands – the site is founded on weakly consolidated Holocene Alluvium overlying weathered bedrock, the proposed structural loads are large, and the new Central Reservoir is to be placed on a pad at an elevation of 182 feet, required placement of up to 30 feet of fill over the current basin. Additionally, the project aims for a long-term foundation solution that will outlive the new replacement tanks and accommodate future site upgrades. In order to meet this goal, the differential settlement criterion for the tanks was ¼ inch over 50 feet length. Lastly, the project also aims to address EBMUD’s increasing trench spoil stockpiles by recycling discarded trench spoils as fill for the proposed tank pad."

Jan 1, 2016

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By Richard A. Forth

During the construction of the Island Line (ISL) in Hong Kong between 1982 and 1986 piled foundations of a building were encountered in a tunnel drive. As the tunnel alignment could not be changed work was temporarily suspended whilst grouting took place beneath the pile cap. The tips of the piles were then cut off. The normal precast concrete lining segments were replaced by the "stiffer" spheroidal graphite iron segments and tunnelling resumed. Settlement of the building was found to be under 10 mm due to the tunnel drive and no damage was reported to the building.

Jan 1, 2002

By J. Don Scott

Analytical predictions of the rate and magnitude of settlement of deposited oil sands tailings slurries generally overestimate how fast pore pressures will dissipate. Field deposits of nonsegregating tailings to mature fine tailings show continued high pore pressures near the surface which impede surface reclamation. In geotechnical analyses which predict the consolidation behavior of soft soils a finite strain theory is used. Effective stress-void ratio and void ratio-hydraulic conductivity relationships determined from laboratory large strain consolidation tests, are used in the finite strain predictions. This theory, however, cannot predict the full range of sedimentation, consolidation and pore pressure dissipation which occurs in large scale deposits of thixotropic tailings slurries. A new large strain consolidation model which assumes that the creep rate of the slurry exceeds the pore pressure dissipation rate is being investigated. This model is relevant for rapidly deposited, low permeability thixotropic slurries where the upwards drainage path increases by several meters a year, such as, in oil sand fine tailings ponds and nonsegregating tailings deposits. The model will be verified by analyzing the 10m high column of fine tailings at the University of Alberta which has been monitored for over 20 years and in which the excess pore pressures are still very high.

May 1, 2004

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By Swaminathan Srinivasan, Aaron J. Muck

"When an opportunity arises to combine state-of-the-art concepts with advanced modeling tools, engineers need to take what they know and apply forward thinking to geotechnical solutions to promote the state-ofpractice. Such an opportunity was seized during the design and construction of the Great American Tower in Cincinnati, Ohio. The forty-one story Great American Tower at Queen City Square – currently the tallest building in Cincinnati – has not only changed the downtown skyline, it is also contributing to the advancement of the state-of-the-art use of auger cast-in-place (ACIP) piles as settlement reducers. Predicted settlements of a traditional mat foundation were excessive, and the costs and construction time associated with traditional ACIP piles extending to bedrock were not preferred. A mat supported on a limited number of ACIP piles, with the piles primarily acting as settlement reducers, was evaluated as the preferred foundation type.Promoting the unique soil-structure interaction of the foundation system with confidence required the use of sophisticated numerical modeling tools. Traditional standard penetration test boring data (SPT) was initially used to develop a numerical analysis of the soil-structure interaction using FLAC 3D software. The model was further modified with cone penetration (CPT) and pressuremeter testing (PMT), along with actual load test results on several ACIP pile elements of varying lengths, but all tipping above bedrock. Through a combined design team effort, and detailed numerical modeling analysis, ACIP piles were recommended for reducing mat foundation settlement. Instrumentation during and post-construction confirmed design assumptions and predictions. Integrating sound geotechnical concepts, and using advanced geotechnical analysis and design methods, traditional mat and ACIP pile foundations were successfully integrated into a unique foundation support system.INTRODUCTIONThe Great American Tower at Queen City Square in Cincinnati, Ohio is located within a region dissected by historical geologic deviances associated with the meander of the Ohio River and glacial progression/recession. Combining a challenging geology, with the development of a high-rise office building afforded the design team an opportunity to combine state-of-the-art soil-structure interaction concepts and method with traditional geotechnical engineering concepts. Such a combination required a variety of field tests, collaboration with the design team and owner, and geotechnical-structural modeling during the design phase. During construction, in addition to materials testing and observation, a variety of instrumentation systems were employed. Together, the data was used to corroborate the design model and make adjustments during construction and further substantiate design assumptions following construction."

Jan 1, 2015

By Werner Bilfinger, Claudio Nahas, Marcelo Waimberg

"INTRODUCTION The so called Porto Maravilha Project consists of the re-urbanization of a 500 ha area in the Rio de Janeiro port region. Several changes in local infrastructure are being implemented, including a significant change in the road system, with the demolition of the former “Via Perimetral” viaduct and construction of 4 new tunnels: • Saúde tunnel - 35 m long (Waimberg et al, 2014); • “Binária tunnel” - 1012 m long; • “Via Expressa” twin tunnels - 1850 m long each way. The tunnels were excavated almost completely in rock using conventional drill and blast methodology and only some short stretches in weathered rock, associated to faults zones, residual soils and marine sediments close to the tunnel portals. During excavation of access shaft and “Via Expressa” and “Binária” tunnels significant ground settlements as well as settlements of buildings founded both on shallow and deep foundations were measured. These values could not be associated to conventional tunneling induced settlement troughs. This paper focuses on the “Via Expressa” tunnels, presenting a brief description of the project as a whole, its geological and geotechnical background, monitoring results, and a discussion of possible causes of the measured settlements. PROJECT DESCRIPTION The Porto Maravilha Project is an integrated multidisciplinary action on behalf of the Rio de Janeiro city council with support from the State and Federal Governments. In addition to creating new conditions for working, housing, transport, culture and leisure for the resident population, it also promotes expressive economic development in the region (Portonovo, 2015). Porto Maravilha Project is carrying out actions for the recovery of the region’s historical heritage, as well as promoting the population´s social and economic development. One of the main benefits of the Porto Maravilha Project is the construction of the new traffic system in the port area, consisting of the Express and Binário roadways. The new project, which will replace the current Perimetral Rodrigues Alves viaduct system, will increase traffic flow capacity by 27%."

Jan 1, 2016

By Fred C. Bond

A study of the settling and thickening of finely divided pulps was undertaken with the object of obtaining certain fundamental relationships, with resulting improvements in the design and operation of mechanical equipment. The subject has been treated in two parts: testing and batch thickening, and continuous thickening, including calculations of capacity and dimensions. Part 1. ? Testing and Batch Thickening The usual method of making thickening tests is to agitate the pulp with a plunger in a graduated glass cylinder and let it settle, while recording the time rate of settling. The settling rates corresponding to different pulp dilutions are found, the ultimate dilution obtained is measured, and the necessary thickener area in square feet per ton of dry solids per 24 hours is calculated, for each pulp dilution. The largest area found is used in selecting the proper thickener size.

Jan 1, 1946

By Jan Steinhoff

The design options of a gravity separator are still limited and rely on the study of settling behavior. A methodology will be presented where an experimentally given inlet droplet size distribution (DSD) is the basis for the calculation of the dispersion layer in a gravity separator. A pilot-scale continuous gravity separator is presented and CFD (computational fluid dynamic) results are validated. A transmitted light measurement technique for the determination of the DSD is presented up to a holdup of 15% dispersed phase. The resulting DSD was in the range of 20–2000 μm depending on flow rate and phase ratio. Furthermore, correlations of the real DSD with the settling behavior of the dispersion in a settling cell are discussed. The new approach to the description of gravity separators will be presented and the applied CFD methods showed good results with the system water/paraffin.

By A. A. Gustafson

IN diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1040. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Freeport Sulphur Co. discharges over the entire circumference, which gives a discharge lip of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole. The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By V. F. Swanson

A mathematical model for free and hindered settling of minerals was developed. This paper describes how to apply the model in designing systems, such as fluidized bed, elutriation, mixing pumping systems, involving solids and fluids.

Jan 1, 2000

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

By H. L. Monroe

Meramec Mining Company, owned 50% by St. Joseph Lead Company and 50% by Bethlehem Steel Corporation,- is engaged in the mining, concentrating and pelletizing of iron ore from the Pea Ridge Mine which is located in the rugged, wooded Missouri Ozarks about 15 miles from the town of Sullivan or 75 miles southwest of St. Louis. The orebody was delineated in the middle 1950's by the St. Joseph Lead Company during the Company's intensive exploration program to discover new lead orebodies to replace the declining reserves of the famous Southeast Missouri Lead Belt. An airborne magnetometer survey was run by the U.S. Geological Survey, the Missouri Survey and several mining companies, (of which St. Joseph Lead Company was the principal supporter). The survey was published in 1950 and disclosed an anomaly in the vicinity of Pea Ridge. In 1950 test drill holes disclosed that under some 1300 feet of sediments there did exist an iron deposit of probable commercial significance. No further action was taken until 1956 when additional drill holes confirmed beyond reasonable-doubt-that this was a major iron ore discovery.

Jan 1, 1965