Search Documents

By Reed M. Izatt

SuperLig® materials are capable of individually separating Rh, Pd, and/or Pt in highly purified form (99.95 to 99.99%) from a variety of chloride-based feed streams in a single stage operation. The hydrophillicity and associated kinetics of the supported materials allow for operation at relatively high flow rates of both loading and elution in a packed bed format. Pilot and commercial systems have been operated with Rh, Pd, and/or Pt present in the feed from single digit ppm (mg/l) to tens of g/l. A dual SuperLig® system for one pass Au(CN)2- separation followed by Cu and CN- recovery for CN- recycle has also been tested up to a pilot level,

Jan 1, 1999

By XUEWEN WANG, Xingming Wang, Xuehui Liu, Mingyu Wang

The Panzhihua titanium concentrate contains high contents impurity of Mg and Al, and it is difficult to prepare high grade titanium slag. To solve this problem, a sodium salt roasting-acid leaching process was proposed for removing the impurities in titanium concentrate. Na2CO3 and titanium concentrate were mixed with the proportion of 1:4, and then the mixture was roasted at 700 for 2h. After roasting, the calcine was leached with HCl solution. The experimental results showed that the removal rate of silicon and aluminum can reach more than 85% and 80%, respectively, at leaching temperature of 70 , leaching time of 4h, HCl addition of 5ml and liquid-solid ratio of 4:1.

Jan 1, 2016

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By Ph. Cauwe

This paper presents the experience that NESA and MECHIM have gained about recovery of non ferrous and precious metals from complex sulfide materials. Processed materials are from natural deposits or metallurgical by-products or residues. Roasting of these materials is closely related to the pyro or hydrometallurgical processes used downstream of the roasting. Conditions of a first step of roasting the SELECTIVE ROASTING, are analyzed and explained. The roasted products so obtained are characterised by an extended elimination of volatile sulfides (AS, Bi, Sb, Sn, Pb, Hg, ?? ) and are readily available for the pyrometallurgical recovery of non ferrous and precious metals. After the SELECTIVE ROASTING, thanks to. the high porosity obtained in the "selective calcine", the SULFATE ROASTING is per-formed in excellent conditions. Hydrometallurgical tests performed for the final calcine show a high recovery of non ferrous and precious? metals and require only simple and well known processes. Many experimental and commercial data are given.

Jan 1, 1983

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By S. Svoronos, B. Moudgil, R. Stana, A. El-Midany

Due to their similar surface properties, it is not always easy to separate carbonate minerals from other salt type minerals by froth flotation. A particular example is the difficulty of separating dolomite impunities from phosphate minerals. Such challenging fundamental and practical problems have inspired several research efforts in various laboratories around the globe to find methods for economically removing the dolomite. However, a universal and cost effective process is not in commercial use. In this paper, a new process for separation of carbonate minerals (dolomite or calate) from other associated minerals is presented. Differential solubility of carbonates in slightly acidic solution is utilized to generate micro GO, bubbles at the carbonate mineral/ water interface. Particle (e.g., dolomite)/ bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro bubble/particle aggregates. Different sutface-active agents were tested to stabilize the bubbles. Results of these tests are presented and the mechanisms involved are discussed.

Jan 1, 2005

By E Forbes, G V. Franks

"This study investigates the dual function of a temperature responsive anionic co-polymer of poly (N-isopropyl acrylamide) (PNIPAM) as a selective flocculant/flotation collector. PNIPAM is used for separating hematite from 50:50 mixtures of hematite and quartz, at a variety of particle sizes. The performance of PNIPAM in this system is compared to that of conventional flotation collectors: sodium oleate and sodium dodecyl sulfate. The results of the study demonstrate that anionic PNIPAM used at 50¦C (above the lower critical solution temperature (LCST)) is the most effective flotation collector for hematite particles in the size range between 10 and 20 ¦m. This is attributed to the increased probability of both particle/bubble collision and particle/bubble attachment through the formation of hydrophobic hematite aggregates. Anionic PNIPAM used at 50¦C also produced the highest hematite recoveries for very fine hematite particles (circa 1 ¦m). However this recovery was completely unselective. This lack of selectivity is partially attributed to the activation of quartz particles by PNIPAM, but is thought to mainly occur as a result of entrapment of quartz particles within the matrix of hematite aggregates.CITATION:Forbes, E and Franks, G V, 2013. Selective separation of hematite from quartz by flotation using a temperature responsive polymer, in Proceedings Iron Ore 2013, pp 381-390 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By A. René Silva

The separation of Fe(III) from simulated Ni(II) solutions using different ion exchange resins was studied. The resins tested included cation exchangers with sulfonic and carboxylic groups and chelating resins with iminodiacetic, aminophosphonic, and mixed sulfonic and phosphonic groups. The dosage of resins was varied from 0.1 to 0.5 g/mL to study the impact of resin type and dosage on iron separation from simulated nickel leach solution containing 25 g/L Ni(II) and 25 g/L Fe(III) at pH 1.5. Also, the effects of different metal ion concentrations, Fe (III):Ni(II) ratios in solution, pH, and adsorption times were investigated. Experimental results demonstrate that all the chelating resins selected favored the adsorption of Fe(III) over Ni(II) with high Fe(III) loading. Soft cation exchange resins also favored the adsorption of Fe(III) over Ni(II), but no significant Fe(III) loading was observed. In contrast, strong cation exchange resins did not show adsorption preferences. The most efficient separation was observed using resin with aminophosphonic groups at resin dosage of 0.2 g/mL, having a Fe(III) adsorption over 94% and Ni(II) adsorption below 5%.

By A. Güney

Currently, recycling technologies use relatively homogeneous plastics because hand-sorting waste feed is too expensive. Many promising technologies for separating mixed thermoplastics are being investigated, but they are still uneconomical and unreliable. Burning plastics for recycling is not used because of poisonous gases released when their burning. PET and PVC cannot be separated using conventional gravity separation techniques because their specific gravities overlap; PET density changes from 1.33 g/cc to 1.37 g/cc and PVC density is between 1.32 g/cc and 1.37 g/cc. For this reason, plastic recycling needs new techniques. Among these techniques froth flotation, also used in mineral processing, can be useful for its cost and simplicity. In this method, a plastic is selected from mixture, tried to regain its natural property, hydrophobicity. In this study the experiments were applied by using plasticizer reagents to make the selected plastics hydrophobic and us-ing NaOH to render the other hydrophilic. Post-consumed PET and PVC are evaluated by concerning the effects of selected parameters (particle size, concentration of plasticizer reagent, amount of NaOH, conditioning time and the effect of conditioning temperature). At the end of the experiments, optimum parameters for selective flotation of PET from PVC was found as particle size of -4.76 + 3.36 mm, NaOH amount of 30 kg/t, conditioning temperature of 75°C, conditioning time of 30 minutes, reagent amount of 300 mg/L. Consequently, PET was re-covered with 99.7% purity and 57% efficiency.

Jan 1, 2014

By Jannette L. Chorney, Katie J. Schumacher, Katelyn M. Lyons, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating a new method of extracting and refining rare earth elements (REEs) from mineral ores and concentrates. The relative stabilities of various REE compounds and differences in vapor pressures are exploited to selectively separate rare earth chlorides, with dysprosium and europium chlorides used as proof-of-concept experimental materials.

Mar 1, 2017

By Ephraim Jeya Kumari

The demand for the titanium dioxide pigments and the shortage of higher-grade titaniferous ores with low radioactivity and zircon sands worldwide has encouraged the development of new techniques for the beneficiation of lesser grade titaniferous ores. The inferior quality ores are invariably richer in radio-active and lanthanide oxides, which severely interfere with the fluidized bed chlorination reaction (FBCR), in which ultra-high purity titanium tetrachloride is distilled off for pigment manufacture. However the present beneficiation techniques require high quality ilmenite ores and are not suitable for upgrading lower grade ilmenite ores which do posses trace metals in the form of lanthanides and actinides as Al-phosphates and zirconium silicates, respectively. The presence of mineral hosts, zircon sand and monazite in ilmenite and anatase also increase in chlorine gas consumption in the FBCR and contribute to a larger volume of hazardous waste production, which must be neutralised at a significant cost before being disposed off safely. In view of the problems described for lanthanide (Ce, Nd etc) and actinide (Th, U) trace impurities in titaniferous ores, an alternative route, which is flexible and more accommodating for processing difficult ores, is discussed. In the new process, which may be used for richer grades of ores too, the ore is roasted in air with sodium carbonate below 950°C to promote the formation of water-soluble sodium ferrite and insoluble sodium titanate phases. In this investigation, the high-temperature roasting process and the ensuing hydrometallurgical leaching steps have been analysed in the context of selective separation of lanthanide and actinide minerals from the main titaniferous mineral structures. Evidences for the selective separation are presented based on the chemical (XRD, XRF, AA) and microstructural analysis (SEM, EDX, EPMA) of roasted mass and the leached product. The efficiency of selective separation is also reported based on the chemicals analysis and the particle size of the materials derived after leaching. The paper highlights the various thermodynamic aspects of reaction equilibrium in the Fe-Ti-O-Na system, and the effect of Eh-pH diagram in the determination of pH required for the better control of the removal of iron and sodium. Two different types of Ti ores, namely ilmenite and anatase, their crystal structure and the phase transformation will also be explained on the basis of wet chemical analysis, XRF, XRD, EPMA and SEM-EDX studies. The method developed examines the technological feasibility of the selective separation process.

Jan 1, 2006

By R. L. Bruening, N. E. Izatt, S. R. Izatt

The need for selective metal separations has increased as the mining industry encounters more complex ore bodies and demand for higher performance end products expands. The Molecular Recognition Technology (MRT) process uses highly selective SuperLig® resins to remove desired metals from a variety of solutions in the mining and metals processing and recovery industries. MRT separation processes efficiently produce high purity metal products. In this paper, applications of MRT to metal recovery at mg/L to multiple g/L concentration levels are presented and discussed. Specific examples in the precious metal, nickel, cobalt, zinc, copper, and rare earth industries are given.

Jan 1, 2014

By R. L. Bruening, R. M. Izatt, N. E. Izatt, K. E. Krakowiak, S. R. Izatt

The need for selective metal separations has increased as the mining industry encounters more complex ore bodies and the demand for higher performance end products expands. Molecular Recognition Technology (MRT) is a green chemistry process that involves use of SuperLig® resins to selectively remove desired metals from a variety of solutions in mining and metals processing industries. Recoverable metal concentrations can range from multiple g/L to mg/L or less. The MRT separation process is based on green chemistry principles and can efficiently produce high purity metal products with minimal waste generation and energy usage. In this paper, applications of MRT to metal recovery and purification in the minor and specialty metals industry will be presented and discussed. Examples will be described involving cobalt, nickel, zinc, rhenium, iridium, indium, germanium, bismuth, and cadmium, as well as removal of lead and iron from process streams.

Jan 1, 2015

By R. L. Bruening, J. B. Dale, N. E. Izatt, S. R. Izatt

IBC Advanced Technologies' Molecular Recognition Technology (MRT) SuperLig® products selectively and rapidly bind with target metal ions to remove them from solution. The MRT process can produce a high purity separation product of maximum added value at low cost. This paper discusses applications for MRT in the gold industry, including recovery of gold and silver as well as metal contaminants from various process and recycle streams.

Jan 1, 2011

By E. S. Peterson

The selective separations of trace metals- and organics from water are processes of importance to industry. The application of a new metals capture technology coupled with polymer membrane technology has proven to be one avenue to accomplish such selective separations. The polymers used in these studies are polyphosphazenes. Polyphosphazene polymers consist of an alternating backbone of nitrogen and phosphorus atoms. The polymers have high thermal and chemical stabilities. Experiments at the Idaho National Engineering Laboratory demonstrate that polyphosphazene membranes coupled with Chromato Chem,"Chelation Chromatography" process are capable of removing both chlorinated hydrocarbons and metal ions from process streams. These results point to a wide range of potential industrial and environmental applications for such systems. Data will be presented which show the efficiency and selectivity of separations, postulated separation mechanisms, and the initial designs of industrial demonstration units which are currently under construction. Parts of this work have been performed under a Cooperative Research and Development Agreement (CRADA) between ChromatoChem, Inc. and Idaho National Engineering Laboratory (INEL). The work at INEL was been sponsored by the United States Department of Energy's Office of Industrial Technologies

Jan 1, 1995

By Ximena Diaz

Mercury is one of the most undesirable contaminants in gold bearing ores. During cyanidation mercury cyanide compounds accompany gold in all the extraction and recovery processes. Of course mercury in the carbon eluates creates environmental problems in subsequent refining steps. One possible process alternative for the separation of gold from mercury in such concentrated alkaline cyanide solutions is the selective solvent extraction of gold by undiluted Dibutyl Butyl Phosphonate (DBBP). In order to describe the behavior of mercury during extraction by DBBP, the results from a preliminary research program are presented. In this study, temperature and cyanide concentration have been found to be the most significant variables which influence the separation of gold from mercury by solvent extraction using DBBP. It was found, using plant eluate from a carbon strip, that excellent separation of gold from mercury can be obtained at 60' C with 98% gold recovery and complete mercury rejection in a single stage of extraction. The influence of pH is also discussed in terms of the extraction chemistry. These results complement previous research which described the DBBP solvation extraction of an aurocyanide ion pair. In addition, these results extend our understanding of the alkyl phosphorous ester extraction systems by illustrating that neutral ionic species such as Hg(cN)02sq, can be extracted at low cyanide concentrations, a phenomenon which had not been observed previously for other cyanoanions.

Jan 1, 1993

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin.The use of selective ion exchange to recover metals from sulphuric acid liquors has been studied for a long time. Companhia Vale do Rio Doce (CVRD) has been actively involved in hydrometallurgical applications of IX and has researched in selecting the optimum resin for nickel and cobalt selective removal and the design of a suitable IX circuit. When an IX operation is contemplated for a specific application, it is followed a screening process which generally involves consideration of the solution composition and pH, speciation of the metals in the liquor to be treated and other possible techniques that can be applied to achieve the desired specifications or recoveries. Once a decision has been made to use IX for a specific application, relevant testwork should be done to select the most cost-effective resin and design the IX circuit to achieve the desired criteria. The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to-solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment"

Jan 1, 2003

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin. The Rohm & Haas chelating resin, Amberlite IRC 748, with its weakly acidic groups, did not work in acidic solution but exhibited good results at pH 4 and above. The resin that efficiently removed metals from high acidic solutions was the bis-picolylamine resin. Maximum nickel uptake values ranged between 85 g and 112 g Ni per Kg of resin.The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to- solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment."

Jan 1, 2003

By L. H. Michaud

A mining company plans to extend its surface coal-mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accountings for the site shows an overall Neutralization Potential to Maximum Potential Acidity Ratio (NP:MPA) of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to be mined. If traditional dragline-mining methods are used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of acid mine drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. To prevent the formation of AMD, the company has proposed to mine the area using truck-shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, amine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil to achieve an overall net alkalinity in all spoil areas. Therefore, mining this site should not result in the formation of AMD.

Jan 1, 1996

By L. H. Michaud

An existing mining company plans to extend their surface coal mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accounting for the site show an overall NP:MPA ratio of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to? be mined. If traditional dragline mining methods were used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of Acid Mine Drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. In order to prevent the formation of AMD, the company has proposed to mine the area using Truck/Shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, a mine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil in order to achieve an overall net alkalinity in all spoil areas. Mining of this site should therefore not result in the formation of AMD.

Jan 1, 1994