Search Documents

By Klaus Schoenert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such subprocesses as: transportation of the particles to the zone where they are stressed; the stressing of particles to a level high enough for breakage; removal of the fragments that are smaller than the limit size from the grinding zone; and prevention of agglomeration of the fine fragments. Breakage phenomena of particles is the most difficult subprocess to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. Two important features of the "Science of Communition" are discussed: the fracture physics and crushing under controlled conditions with special reference to single particle crushing, packed bed crushing, measurement of energy needed for fracture, fragment size distribution, and new surface area produced. The important features of these aspects are detailed, namely, energy balance of a crack, influence of environment, specimen size problems, and energy utilization in single particle crushing.

Jan 1, 1973

By Nar S. Dala1, Xianglin Shi, Val Vallyathan

"Electron spin resonance (ESRJ and cytotoxicity measurements were made on newly fractured silica to examine specifically the role of the fracture-induced, silicon-based radicals (Si· and SiO·) and silica-generated hydroxyl (·OH) radicals in the mechanism of the cell membrane damage by silica. The concentration of the Si· and SiO · radicals was controlled through decay processes, thermal annealing, and boiling, while that of the ·OH radicals was varied by using catalase, superoxide dismutase, KMnO, Na;iSeO:y ascorbic acid, and metal ions, and monitored via ESR spectroscopy. The dust's cytotoxicity potential was evaluated by measuring the silica-induced hemolysis and also by determining lipid peroxidation (using linoleic acid). From the comparison of hemolysis and ESR results it is deduced that the radicals play little or no role in the silica-induced hemolysis. However, the lipid peroxidation data indicate that the radicals might be involved in the initiation of an oxidative chain reaction leading to the macrophage membrane damage through lipid peroxidation. INTRODUCTIONThe biochemical mechanism of quartz-related pneumoconiosis is still not fully understood. It is believed, nevertheless, that one event of primary importance is the perturbation of cell membranes by the dust particles (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Parazzi et al., 1968; Reiser and Last, 1979; Shi et al., 1989; Summerton et al., 1977). The ensuing cell: membrane damage unleashes certain lytic enzymes resulting in additional cell injury and eventual fibrosis (Nolan et al., 1981; Summerton et al., 1977). Thus considerable effort is currently being made toward the understanding of the processes by which quartz particles disrupt the membrane of a red blood cell (RBC) or a pulmonary alveolar macrophage (PAM). A simple but important method of evaluating the membrane damage potential of a dust is the hemolysis test (Harington et al., 1971). Even though this test is used routinely for screening dusts for their cytotoxicity potential, the biochemical mechanisms underlying the cell lysis by many dusts, including quartz, is still controversial (Kilroe-Smith, 1974; Singh and Rahman, 1987), and this provided us the impetus for the present undertaking."

Jan 1, 1990

By C. P. Mangelsdorf

The roof truss as a means of secondary or supplemental mine roof support has enjoyed increasing acceptance in recent years, particularly in bituminous coal mines. In those entries where long life is required or doubtful performance from other forms of support seems likely, trusses in many cases have provided the necessary protection for continuing operations. Although relatively expensive and time-consuming in their installation, trusses, particularly with the new resin point anchor system, appear to be justifying their higher premium. It seems inevitable that techniques and equipment for installing them within the cycle will soon be developed. The actual mechanism by which trusses contribute to the stability of a roof is, as yet, poorly understood, and it may be that more than a single mechanism is involved. There are, however, a number of useful observations which can be made concerning the structural behavior of the truss itself, based solely on the mechanics of rigid and deformable bodies. The purpose of this article is to present some of these observations, particularly relating to friction in the system. A few speculations concerning the roof must, of course, be made. From a knowledge of the structural behavior, some insight into the truss-roof interaction may be gained. The concept of the truss is quite simple. As shown in [Fig. 1], it consists of two inclined chords (usually at 45') anchored in holes drilled in the roof over the ribs. A horizontal chord is formed connecting the exposed ends of the inclined chords, either with a third piece or by bending extensions of the inclined chords until they meet in the middle. A distinction can be made between active and passive chords of a truss depending upon the manner of installation. If the inclined chords are fully grouted and the horizontal chord is merely attached to them, it may reasonably be assumed that no significant forces exist in the truss until the roof begins to work. Such would be a completely passive system. On the other hand, if the inclined chords are anchored only at their upper extremities and the horizontal chord is formed in such a way that all three chords can be pretensioned to a significant portion of their tensile strengths then the truss may be regarded as fully active. Combinations of active and passive chords are also possible. * The discussion here is confined to the fully active truss such as the Birmingham steel rod system or the Galis wire rope truss. In both cases, pretensioning is accomplished by tightening of the horizontal chord, some of which tension is transferred to the in-

Jan 1, 1981

By Brij M. Moudgil

Lack of understanding the major process parameters and inadequate scale-up factors have led to the belief that fundamental knowledge is not important for successful flotation plant operations. Flotation of simple and easy to process ores may not require a strong fundamental knowledge base for day to day operations. However, as low grade complex ores are mined and process control is integrated into flotation schemes, it is imperative for a plant operator to acquire a strong background in the basics of the flotation process at hand and/or have access to such a knowledge base at short notice. In order to meet the challenges of unexpected changes in the feed, reagent quality, water chemistry, physical, mechanical and hydrodynamic conditions, the flotation plant superintendent/chief metallurgist must have a strong background in the flotation fundamentals.

Jan 1, 1993

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By J. Stachurski, N. A. Abdel-Khalek

Laboratory Potation tests were carried out on six Polish coal samples of different rank. Each coal sample was screened into seven size fractions. The floatability of size- by-size for various size ranges for different samples was investigated as well as for the original samples. The results showed that in flotation of size-by-size, the intermediate sizes varied with the rank of the coal. Entrainment was shown to be an important mechanism in the recovery of fine particles in flotation of the original samples.

Jan 1, 1991

By E. Paransky, M. Rigaud, G. Paschek, S. Palco

Some of the negative impacts of carbon addition on the strength of castables are yet to be overcome in order to fulfill its potential benefits for oxidation resistance. This paper reports the results of recent studies conducted at CIREP on the effects of different types of carbon additives on the thermo-mechanical properties of magnesia-based castables. Experimental techniques included measurements of the hot modulus of rupture (HMOR), hot modulus of elasticity (HMOE), as well as the wedge-splitting test (WST). The comparison of evolving microstructures was carried out employing scanning electron microscopy with microanalysis attachment (SEM/EDS) and X-ray diffraction (XRD). HMOR values of 12 MPa at 1300°C have been reached in MgO-Si02-C castables containing up to 7% carbon.

Jan 1, 2004

By Robert L. Bates

In this paper I use the term "industrial minerals" in its broad general sense, and I distinguish two main groups. The first consists of the bulk materials, characterized by low unit price, nearness of deposits to markets, relatively simple methods of extraction and processing, and a tendency to be closely related to the construction industries. The second group includes those materials valued for exceptional purity, or for some special property such as hardness, immunity to acids, or dielectric strength. These materials are produced in smaller amounts, at high unit values, from deposits notably restricted in. distribution; and they require more or less sophisticated methods of production and beneficiation. The applications of this second group are not closely tied to any particular part of the economy. From the way in which the commodity committees of the Industrial Minerals Division are set up, I take it that the chief interest of most members is with the first group of materials mentioned above. Hence this paper will deal mainly, though not exclusively, with such bulk commodities as sand and gravel, clay, and stone. The first word in the title of the paper also requires brief explanation. It is here given a threefold interpretation. First is the role of the industrial minerals themselves in industry; this would probably be taken as the conventional meaning of the title* The second is the role of the industrial-mineral producers as citizens of the community. The third is what may be called the scientific role of these producers.

Jan 1, 1964

By V. I. Lakshmanan

Wastes when produced can be reused or recycled prior to disposal. Industries that cause environmental concerns during manufacturing include primary materials and primary metals. Pollution prevention mechanisms to achieve waste reduction require new separation, reclamation, control and process simulation technologies. Substituting recyclables for virgin resources will reduce energy use, water pollution, air pollution, water use and mining wastes. Shrinking landfill space will spur new technologies for waste treatment and recycling. These situations hence offer opportunities for innovative flowsheets with appropriate separation technologies. Development of innovative flowsheets to treat recyclables offer unique opportunities for process/product development, obtain green products and hence market advantage. The paper will illustrate with selected innovative flowsheets to treat recyclables.

Jan 1, 1996

By V. I. Lakshmanan

"Historically flowsheets are developed for efficient separation of metals for economic recovery. With increasing emphasis on reduction, reuse and recycle (3Rs) efficient methods are sought to recover values from a variety of feeds where cost of collection, transportation, local consumer behaviour and regulatory guidelines dictate the development of economically viable flowsheets. Innovative understanding of potential market applications can provide means to develop value added end products. The paper with examples will discuss the use of innovative-separation technologies to obtain value added end use materials from secondary sources.IntroductionFlowsheets are developed for the efficient separation of materials of value for economic recovery. However with increasing societal pressures and regulatory initiatives for stricter environmental guidelines, there is strong need to provide focus to recover materials efficiently and economically in an environmentally accepted manner. North American industries are increasingly caught between demands for high technology value added products and responsibility for environment. An aspect that is receiving increasing attention is Design for Environment'. This incorporates a system wide approach for product design and incorporates environmentally preferable features such as recyclability, disassembly, maintainability, reusability and use of safe materials as part of a product's design objectives.The present paper with case histories will address innovative flowsheet development to convert wastes into recyclables value added products or for minimising generation of waste materials. Case HistoriesProcess for Separating Fibres from Composite Materials 1In the automotive industry, sheet molded compound (SMC) is used to produce panels, bumpers and the like. During the manufacture and at the end of life, considerable waste materials are generated which are potentially recyclable. Fibre reinforced plastics where fibre substrate impregnated with thermosetting resin, find applications in several manufacturing processes and are potentially recyclable at the end of life."

Jan 1, 1996

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association four distinct facies (oxide, carbonate, silicate, and sulfide) were identified in an Algoma type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and CO2. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1981

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association, four distinct facies (oxide, carbonate, silicate and sulfide) were identified in an Algoma-type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and Cop. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1982

By X. Cao, X. -G. Chen, K. Liu

As is well known, the standard Al-Cu 206 cast alloys have extremely low iron contents, usually less than 0.15 wt. %. Recently it is found that the iron contents of the 206 cast alloys can be extended up to 0.5 wt. % through the precise control of the iron-rich intermetallic phases. In the present work, the tensile fracture surfaces of the 206 cast alloys with various iron contents are systematically analyzed to understand the failure mechanisms. Results show that higher iron contents can reduce the tensile properties (especially the ductility) of the alloys mainly due to the increasing volume percent and size of the iron-rich intermetallics. Tensile failure mainly occurs at the iron-rich intermetallics/matrix interfaces for the platelet ß-Fe, but by the self-disassociation for the Chinese script a-Fe and Alm(FeMn). Cracking is easier to initiate and propagate along the longitudinal axis of the platelet intermetallics, but it can be deflected along the branches/arms of the Chinese script iron-rich phases, making the alloy more resistant to the propagation of the cracks, and thus the Chinese script iron-rich intermetallics are less harmful than platelet ß-Fe. In addition, it was also found that the Chinese script a-Fe has even a less damaging effect compared to the Chinese script Alm(FeMn) due to the relatively small size and compact morphology.

Jan 1, 2014

By J. Iannicelli

Kaolin tailings ponds play an important role in reclamation of land and water. Discharges impounded from kaolin plants include oversize fractions consisting of coarse kaolin, mica, quartz as well as magnetically extracted contaminents, acid filtrates, and plant washdown streams. Tailing ponds perform an essential function in sedimentation of particulates, blending and reoxygenation of liquid waste, and neutralization and clarification of discharge water. During the past fifteen years, most kaolin firms have segregated their coarse filler waste to allow for possible reclamation for production of delaminated coating clay. This excess coarse filler fraction constitutes a reserve for future coating clay production.

Jan 1, 1985

By S. C. Tennant, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Immobile-element lithogeochemistry is providing a detailed chemostratigraphy of the submarine Ordo-Silurian volcano-sedimentary sequence. Primary lithologies and magmatic affinities of the sericitised and silicified volcanics are determined from binary plots of Nb, Zr, Y, TiO2 and Al2O3, while mass-change calculations using immobile-element anchors can identify and quantify zones of significant hydrothermal alteration. Stratiform polymetallic mineralisation at the western margin of Parys Mountain, around the Penymynydd fault zone, has been shown to have a distinct hanging-wall and footwall stratigraphy. These ore zones are probably part of a homoclinal, north-younging volcano-sedimentary sequence. The apparent stratigraphic complexity results from primary lithofacies variations and pervasive alteration, with the modifying role of the Caledonian orogeny much less than previously suggested

Jun 19, 1905

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By Steven D. Scott

The source of ore metals for base and precious metal volcanogenic massive sulfide (vms) deposits has been debated for decades. Metals can be obtained from high-temperature sea water-rock reactions in subseafloor circulatory hydrothermal systems, or provided by the magmatic fluids that are degassed from magma. The magmatic signatures are largely erased in the hydrothermal system by the overwhelming, long-term circulation of seawater. Melt inclusions in phenocrysts (plagioclase, olivine, pyroxene) of volcanic rocks provide an effective means of understanding the potential for a magmatic contribution to the ore-forming fluids. We present results of a melt inclusion study on the volcanic rocks that host active seafloor hydrothermal fields in the eastern Manus immature back-arc pull-apart basin of Papua New Guinea and an Ordovician-age back arc in New Brunswick, Canada that hosts the ?giant? (330 mmt) Brunswick #12 vms ore deposit. A fluid phase is typically observed in cavities within melt inclusions, indicating that the magma was saturated with volatiles prior to its eruption. The fluid is CO2-dominated with lesser H2O and CH4 in melt inclusions of mafic volcanics and is H2O-rich in felsic volcanics. Tiny crystals and amorphous precipitates (recrystallized at Brunswick #12) of Fe, Ni, Zn, Cu and Mn chlorides, sulfides and oxides coat the walls of the vapor cavities. The crystals include magnetite, magnesite, calcite, anhydrite, gypsum, barite, pyrite, chalcopyrite, halite, silicates and apatite. At Manus, the compositions of the precipitates on the bubble walls of melt inclusions are similar to those found in the vesicles in the matrix glass of the same sample. The ore metals in the volatile phases changed from Ni+Zn+Cu+Fe ? Cu+Zn+Fe ?Fe+Zn (+Pb?) as the magma evolved from basalt, basaltic andesite ? andesite, dacite ? rhyodacite, rhyolite. Glass of the melt inclusions compared to that of the matrix of the rocks from Manus have significantly higher concentrations of H2O (av. 1.64 vs 0.7wt%), Cl (av. 2500 vs1300 ppm) and S (av. 900 vs 100 ppm) suggesting that these volatiles were extensively exsolved from the magma. A minimum of 1.0 to 1.7wt% of magmatic volatiles is estimated to have been degassed before and during the eruptions. The focused discharge of a magmatic fluid as a result of pre-eruptive degassing could be responsible for the metals in the sulfide deposits on the seafloor. If 1 km3 of magma were emplaced in a shallow chamber, then the associated magmatic fluid would be 35.1 million tonnes. If this fluid contained 2.3 wt% Zn and 7.2 wt% Cu (Yang and Scott, 1996, Nature), a total of 0.8 million tonnes of Zn and 2.5 million tonnes of Cu would be to the hydrothermal system.

Jan 1, 2005

By Donald Leroux, Simon Gariépy, Luc Lachance

"Quantitative information about the quality of metal balance results is often overlooked when making important plant production planning decisions. Not only is this common omission made in a context where many measurements taken in and around mineral processing plants carry significant errors, but it also conflicts with the AMIRA P754 Code of Practice for Metal Accounting. The fact that metal balances are typically published without any indication of data quality may give the wrong impression that the measurements are unquestionably accurate. While it is true that statistical data reconciliation can improve the confidence intervals of redundant variables, there is no data processing technique that brings them down to zero at a finite cost. In this paper, we review the entire data flow, starting from field instruments to metal accounting-based decision-making to show how measurement errors are transmuted into business risks associated with production planning. Necessary conditions for first exposing then quantifying such business risks are stated. Pitfalls to be avoided are also discussed. Finally, a simplified risk assessment and management procedure which considers the quality of metal balance results are applied to a polymetallic mineral processing plant. INTRODUCTION Each and every mineral processing plant has production reporting obligations. In this paper, we are concerned with metal accounting reports (Morrison, 2008) where saleable metal flows and inventories are estimated and published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimisation, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that spotless metal accounting is instrumental to high-quality corporate governance (Gaylard et al., 2014) of mining and metallurgical companies. To this extent, one would have expected industry-endorsed standards to have emerged a long time ago. However, the lack of an accepted set of standard procedures for metallurgical accounting was explicitly recognized as an industry-wide problem only in August 2001 during an SAIMM workshop held in Cape Town, South Africa. Discussions that followed this workshop led to the initiation of the AMIRA Project P754, “Metal Accounting and Reconciliation”, in 2003."

Jan 1, 2015

PAGE Problems of American Railroads Early in 1936, by J. J. Pelley 3 The Heavier Nonferrous Metals in Transportation, by C. H. Mathewson... 9 Light-weight Metals in the Transportation Industry, by Zay Jeffries 21 Trends in the Metallurgy of Low-alloy, High-yield-strength Structural Steels, by H. W. Gillett 40 Structural Steels and Light-weight Metals in the Transportation Industry, by Horace C. Knerr 62 Proposed Use of Alloys in Merchant Shipbuilding, by Edgar P. Trask 66 Mutual Effects of Metallurgy and Speed in the Automotive Industry, by Merrill C. Horine 84 The Railroads and Light-weight Equipment, by W. W. Colpitts 93

Jan 1, 1936