Search Documents

By Catherine Aimone-Martin, Mary-Alena Martell

Whole-structure and mid-wall responses of 33 non-traditional structures to surface coal mine blasting were characterized. Eighty-nine blasts were conducted at 11 mine sites throughout the U.S. to measure blastgenerated dynamic response of structures typically found in the proximity of surface coal mining. Structures selected for this study include log-type, manufactured (single- and double-wide trailers), “mine camp”-type, adobe, and stone. Traditional acoustic microphones, t&axial (ground) and single component (structure) velocity transducers were used to record airblast, ground motions, and structures response time histories with a common time base. Wall crack displacement gages were used to record static and dynamic movement of existing drywall cracks. The relative responses of selected “atypical” structures to blast vibrations and nonblasting causes of structural stress, including natural forces, environmental effects, and human habitation, are compared. The purpose of this study is to document and compare vibration characteristics of structures that were not included in previous studies conducted by the U.S. Bureau of Mines and others in establishing the widely adopted safe level blast vibration criteria in the U.S. An important objective of this study is to outline an evaluation process including structure uniqueness relative to cracking susceptibility.

Jan 1, 2002

By N. Saeidi

"For a mine section comprising 100 different stoping activities, there are ~10158 different possible stoping sequences to explore in the mine schedule optimization search and this figure is indicative of the challenge posed in maximising profitability through mine schedule optimization. Any viable excavation timetable must satisfy all conditions that will constrain feasible sequences. In general, consideration of additional constraint will tend to reduce profitability. Geomechanical constraints on mine schedules, introduced with the aim of avoiding excavation instabilities, can be established for underground mine schedule optimization processes but, currently, this is done only rather crudely; precedence relations between excavation activities (stoping or development) are encoded to produce particular stope sequence patterns (e.g. ‘chevron’ or pyramidal sequences).The work reported aimed to investigate automated processes for formulation of such geomechanical constraints. The timetable optimization approach to the problem precipitated a fresh look at time dependent, and excavation sequence dependent, deformation. Abundant evidence emerged that supported the notion that any methodology developed that failed to account for such time and sequence dependencies was itself bound to failure. Yet, it was also recognised that any deviation at all from an assumption of linear elasticity for geomechanical numerical modeling, adopted to inform geomechanical constraint formulation, would rapidly lead to impractical levels of computational effort.Thus the approach presented here represents a compromise: the elastic stress fields induced by individual mining activities are computed for each activity, independently considered within a computational domain identical to that of all other activities. These are stored in a database. Instability risk for a specific sequence of mine activities can be assessed through superimposition of stress fields drawn from the pre-computed database. Time stamps allocated to events corresponding to the excavation processes permit the conversion of the sequence of elastic stress fields into a time table of stress fields. For specific locations within the computational domain, the aggregate effect of the sequence of mine activities leads to stress-time histories having a castellated appearance, a result of the near instantaneous response of an elastic medium to the excavation perturbations. Time dependent deformation responses are crudely allowed for through the re-profiling these castellated histories through graphical construction of curved responses, where the curve gradients are related to a viscous parameter. Such curves form the basis for a geomechanical constraint formulation to be adopted for mine schedule optimization."

Jan 1, 2015

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Mark S. Stagg, David E. Siskind

The mining industry occasionally blasts near pressurized transmission pipelines and has requested guidance of safe vibration levels and setback distances. the Bureau of Mines and the Indiana Department of Natural Resources cooperated with AMAX Coal Company on a study of coal mine overburden blasting. Five buried and pressurized 250-ft pipeline sections were specifically installed on the Minnehaha Mine highwall near Sullivan, IN for testing to failure. Four welded steel pipes ranging from 6- to 20- in diameter and one 8- PVC water supply pipe were monitored for vibration, strain, and internal pressure for a period of 6 months while production blasting advanced up to the pipeline field. In contrast to previous studies of small-scale blasting representing construction activities, these tests involved overburden blasts of up to 2100 lb per delay in 12-l/4-in diameter holes.

Jan 1, 1996

By Mark S. Stagg, Siskind David E

The mining industry occasionally blasts near pressurized transmission pipelines and has requested guidance on safe vibration levels and setback distances. The Bureau of Mines and the Indiana Department of Natural Resources cooperated with AMAX Coal Company on a study of coal mine overburden blasting. Five buried and pressurized 250-ft pipeline sections were specifically installed on the Minnehaha Mine highwall near Sullivan, IN for testing to failure. Four welded steel pipes ranging from 6- to 20-in diameter and one 8-in PVC water supply pipe were monitored for vibration, strain, and internal pressure for a period of 6 months while production blasting advanced up to the pipeline field. In contrast to previous studies of small-scale blasting representing construction activities, these tests involved overburden blasts of up to 2100 lb per delay in 12-1/4-in diameter holes.

Jan 1, 1993

Opportunities to monitor and control primary grinding mill performance are strongly sought after in the mineral processing industry. Currently, limited on-line information about mill charge motion and content is available to mill operations for control purposes, leading to periods of lower throughput, instability, variable product size and accelerated mill liner and lifter wear. In response to this need, CSIRO has developed an on-line surface vibration monitor for primary grinding mills which produces data that has been shown to provide new information about the mill charge in terms of toe and shoulder position, as well as potentially key features such as the overall charge level, the distribution between rock and balls in the mill, and the impact of the charge on the mill liners and lifters. This paper outlines the key features of the on-line monitor system, particularly those relating to data transmission, data analysis, and the design of the monitor and its independent power supply. It describes the coupling of single vibration sensor data from the CSIRO on-line monitor to the actual operating conditions of a SAG mill and how the vibration response and hence mill operating conditions vary as a function of time, including during mill equipment failures such as a broken discharge grate. Opportunities for improved mill control based on the data from the on-line monitor are also discussed, as well as the implications in terms of mill processing and maintenance performance. Recently a CSIRO monitor was also installed on a ROM ball mill and analysis of the vibration sensor data from this installation is currently underway. Preliminary findings from this installation will be presented along with comparisons of generic information, such as toe position (measurement precision and operation variability) and vibration signal (intensity, sensitivity and operation variability), between this type of primary grinding mill and AG/SAG mills.

Sep 1, 2012

By Steven V. Crum, David E. Siskind

In response to its own concerns and those of the public, industry and regulatory agencies, the Bureau of Mines is studying the impacts of low-frequency blast vibrations on structures. Previous research has identified potential problems associated with low-frequency ground vibrations and also found that their existence was not particularly rare, given large surface mine blasts and certain geologic conditions. Only a limited amount of data existed in the blast vibration literature on structure response to ground-vibration frequencies below 6 Hz.

Jan 1, 1993

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Xuezhong Wang, Hao Guo, Tao Tu, Qingsheng Liu

The scheelite concentrate was leached with a mixture of sulfuric and oxalic acids. Chemical compositions, mineral phases, and morphology were characterized by XRF, XRD, and SEM–EDS. Based on the results of the single-factor experiments, the response surface methodology (RSM) was chosen to optimize the leaching parameters: temperature, time, and concentrations of sulfuric and oxalic acids. The RSM results indicate that the optimum values for those parameters are as follows: temperature 72 ℃, sulfuric acid concentration 1.48 mol/L, oxalic acid concentration 0.96 mol/L, and reaction time 2 h. Under the optimal leaching conditions, the model predicts a maximum leaching yield of 99.5%, compared to the value of 99.1% obtained experimentally, that is, a discrepancy of only 0.04%. This good correlation shows that the quadratic polynomial equation obtained by the RSM optimization is reliable. The importance on leaching parameters of scheelite is, in decreasing order, temperature, time, sulfuric acid concentration, and oxalic acid concentration.

Oct 11, 2021

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By Jian Liu

The study aims to leach copper from a low-grade flotation middling by optimizing the leaching process using response surface methodology. The effect of key parameters, i.e., sulfuric acid concentration, nitric acid concentration and leaching time, on the leaching efficiency was investigated and a quadratic model was suggested by the methodology to correlate the variables to the efficiency. The results indicate that the model is in good agreement with the experimental data at a correlation coefficient (R2) of 0.97 and the most influential parameter on efficiency was identified as sulfuric acid concentration. The optimum conditions for copper leaching from the middling were identified as sulfuric acid concentration at 103.74 g/L, nitric acid concentration at 12.50 g/L and leaching time of 30.98 min; under such a condition, an average leaching efficiency of 93.16% was achieved from the middling.

Jan 1, 2011

By Mario Terceros H., Bengt H. Fellenius

"ABSTRACTFour strain-gage instrumented bored piles were constructed in a sedimentary, dense to very dense, fine to medium sand in Santa Cruz, Bolivia. Two of the test piles were the normally used bored pile constructed with bentonite slurry and two piles were Bauer Full Displacement Pile (FDP). One of each pair was equipped with the Expander Body, an inflatable steel cylinder that on pressure-grouting provides an enlarged pile toe. Head-down static loading test were performed on three of the piles and a bidirectional test was performed on the fourth pile, a standard pile with Expander Body and a bidirectional cell placed immediately above the EB. The latter pile was tested in 3 phases. First by activating the cell, second, by a head-down test, and, third, by a repeat bidirectional cell test. The static loading tests proved the shaft resistance of the FDP pile to be about twice that of the standard bored pile and that the Expander Body more than doubled the toe stiffness. The strain-gage records showed that the standard bored piles had multiple bulges and neckings, which affected the evaluation of the axial stiffness and load distribution of the piles. The testing programme was used for a prediction event with 60 persons, ahead of the tests, submitting predictions of the load-movement curves for the test piles and also a capacity appraised from the curves.1. INTRODUCTIONOn April 23 - 26, 2013, the First International Conference and Seminar on Deep Foundations was held in Santa Cruz, Bolivia under the auspices of INCOTEC SRL, the UAGRM University, and the Bolivian Association of Civil Engineers and Chamber of Construction. To coincide with the conference, a research study on construction and static and dynamic testing of four instrumented bored piles was undertaken. To ""add spice"" to the conference, a prediction event was organized on the test programme. This paper presents the soil conditions at the site, the type and construction of the test piles, the outcome of the prediction event, and the results of the static tests.2. SOIL CONDITIONSGeotechnical studies comprising SPT and CPT tests with routine laboratory analysis were performed on recovered soil samples. Three SPT boreholes were put down at three of the locations of Pile TP1, TP2, and TP3, at 5.0 m distance from each other. The SPT procedure consisted of manual hoisting of the weight by three crew members pulling on ropes over a pulley supported by a tripod and letting the weight fall by gravity. The groundwater table lies at 3.5 m depth.Figure 1 shows diagrams of the SPT N-indices and the distribution of water content in the three boreholes. The SPT-indices show the soil density to be compact. The average water content is about 15 %, plus-minus a few percent."

Jan 1, 2014

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By John A. Herbst

At the last Comminution Symposium a challenge (Meloy and Williams, 1992) was issued to "predict the typical straight-line, self similar" tumbling mill product size distributions using a population balance model (PBM). Implicit in this challenge is the assumption that the PBM is inadequate for predicting real world grinding performance. This response is presented in three parts: I. Theoretical analysis of the general PBM and its appropriateness for comminution system modeling. II. Examination of the accuracy of prediction of real world milling behavior using linear and nonlinear PBMs. III. Evidence from recent microscale comminution research. This paper concludes with recommendations concerning future research which will: 1. further elucidate mechanisms of particle destruction and creation as well as attrition and 2. increase the accuracy of model predictions in highly nonlinear situations

Jan 1, 1997

By R. J. Lytle

Geophysical exploration for engineering purposes is conducted to decrease the risk in encountering site uncertainties. Such studies are needed in construction of underground facilities. Current responsibilities, opportunities and challenges for those with geophysical expertise are defined. These include: replacing the squiggly line format, developing verification sites for method evaluations, applying knowledge engineering and assuming responsibility for crucial national problems involving rock mechanics expertise.

Jan 1, 1982

Owner?s Team and EPCM ?Teams rolesmay vary to suit the skills available, however the tasksremain the same ?Ensure adequate level of capability in the team ?Large owner?s teams vssmall owner?s teams ?size of owner?s teams can reflect not only the individual level of capability but also the type ofrelationship with the EPCM contractor ?Wholly owned projects vsjoint ventures projects ?Both cases require clear accountabilities and authorities ?Project sponsor should be a senior executive with commercial andtechnical accountability of project outcome ?Project leader should be experienced and have solid leadership capabilities ?Attention should be paid to balancing personality types in an owner?s team

May 1, 2010

By Andreas Rubo, Stephen Gos

In the days of increasing environmental and safety awareness many efforts have been made to prevent losses of both an evident economic nature and also less obvious losses. These losses could be associated with damages due to negative impact on the environment and also people coming into contact in a broader sense with any toxic chemical. This paper deals with how cyanide can be applied in a responsible manner at a modern gold mine. Responsible application is achieved by minimizing losses of reagent and avoiding negative impact on the environment as well as adopting a Responsible Care philosophy to the application of cyanide. It becomes evident that this is quite a complex system with a greater commitment than avoiding reagent losses for economic purposes.

Jan 1, 1997

By César Ugaz, Jorge Cardenas

Mitigating the vibrations resulting from a blasting rocks is one of the most common challenges that Peruvian mining has, since if this impact is not mitigated it can generate discomfort and altercations with neighboring communities and also puts the continuity of the mining project at risk. In that sense, we must establish control parameters to mitigate these effects as much as possible. As a starting point we must establish areas of interest that in this context would be the communities near the mine; first stage to carry out constant monitoring at these points, the registration of vibrations and noise is vital for the success of this control, with this information we can establish predictive models, the registration of elemental waves and the evaluation of human perception. In a second stage, this information allows us to make decisions in engineering such as the selection of delay times, elaboration of detonation sequence schemes, maximum amount of operating load per delay window, as well as the use of special load designs (Decks). There is a fear that these controls generate negative impacts to the process, referring to fragmentation, dig rate, throughput, etc. Since we limit the explosive load necessary for the results we need. To avoid this we use "Decks" type load designs under a sequencing between these under time calculations by elemental waves, which generate a reduction in vibrations up to 50%, also complying with strict regulations without affecting the power factors to comply with our performance indicators. Finally, in a third stage we must carry out a constant evaluation of results according to the progress of the mine.

Jan 26, 2026