Search Documents

By J. H. M. Thomeer

A method is presented that provides a mathematical description of capillary pressure curves and, probably, of differences in pore geometry of samples. The technique is based on the observation that the location and shape of a capillary pressure curve reflect characteristics of the pore structure of the sample. INTRODUCTION It has been noted1-5 that the observed differences in shape and location of capillary pressure curves reflect some basic properties regarding the pore geometry of the samples. For example, according to basic concepts of capillarity, the following statements can be made regarding the location and shape of a capillary pressure curve.* The location of the curve with respect to the (Vb)pc and PC axes is a measure of the interconnected pore volume and of the cross-sectional area of the pore first entered by mercury, respectively. The shape of the curve depends on the interconnection of the pores and the sorting of the pore sizes. It has been the object of this study to use this information as a starting point in an attempt to find a unique mathematical description of the PC — (Vv)p, relations of different samples. It may be expected that parameters in such a relation can then be used to describe differences in pore geometry of these samples. For a practical description of the PC — (Vb)p, relation, however, it appears desirable to describe each curve (i.e., each sample) by a limited number of parameters so that the curves taken from all samples form a family, each member of which is uniquely determined by one single combination of values of all parameters.

By W. F. Hower, W. Brown

Large-scale sand consolidation tests were conducted in an effort to determine the reasons for the successes and failures of this method of sand control. Several different consolidating materials were used in treating both clean and bentonitic sands that were packed in a chamber having a capacity of 3.3 cu ft. The results were essentially the same for all of the different consolidating materials, The data show that low-viscosity consolidating materials pumped at a relatively slow rate gave the best results. Where the formation has produced sand, the treating fluids can compress the formation, thus permitting the channeling of fluids to another horizon. Pressure-packing these zones before attempting to consolidate is recommended. Sands containing more than 4 per cent of water-swelling clays are not good candidates for consolidation. It is indicated that loose sand, particularly when it is bentonitic, can be fractured during the placement of the treating fluids. INTRODUCTION Sand production in oil and gas wells has plagued the industry for many years, and numerous cures for this problem have been suggested. Most methods have been successful to a certain degree, but the great variety of well conditions that exist in the different areas has magni- fied the problem and limited the successful use of the various systems. Four review papers1-4 present a wealth of information concerning the degrees of success that have been obtained by the different sand-control methods. The bridging of sand grains by the use of gravel packs and screens has been quite successful. However, these methods do not leave the casing clear for all types of multiple completions, and the cure does not last for the production life of the well in some instance:;. The control of loose sands by sand consolidation with resins has never been as successful as desired. It has always been hoped that such a treatment would eliminate all sand problems for the life of the well, but. initial applications, starting in the middle 1940's, were only moderately successful. Lott, et a1,3 reported a success ratio of approximately 50 per cent and made the following conclusions. The highest percentage of successes were obtained where: a. Consolidation of a zone was made at the time of initial completion or prior to the production of sand. b. The interval treated was less than 12 ft in length. c. Between 30 and 50 gill plastic/ft of producing interval was displaced through the perforations. REASONS FOR SAND CONSOLIDATION FAILURES Our own experiences in the field of sand consolidation point toward the following conditions as the major reasons for the failure of sand consolidation attempts. 1. Mud-plugged perforations and mud invasion of the formation. 2. Sand in the casing covering all or part of the perforations. This sand could be either formation sand or one of the coarser sands used as propping agents in hydraulic fracturing. 3. Holes in the casing. 4. Channels behind the casing. 5. Attempting to treat too long a perforated section. 6. Too high a percentage of water-swelling clays in the formation. 7. Formations that have produced sand. Recent attempts were made to treat perforated sections ranging from 10 to 30 ft, in wells that have produced sand, by using a straddle packer that was raised and lowered through the perforations as the consolidating material was being pumped. In most instances, the pressure required to pump fluid into the formation varied considerably as the tool was raised and lowered. This suggested the possibility that significant differences in permeability were present or that only part of the formation had produced sand. There were times when a sudden break in pressure indicated that a fracture was being formed. Research conducted several years ago concerning the problem of the control of water in air and gas drilling indicated that shale sections could be fractured quite easily. In addition, it was determined that it was easier to pump fluids into shale bodies by fracturing the shale itself, or the interface between the shale and sand, than to pump into a fluid-saturated formation. Formations that produce sand are usually adjacent to shale bodies and frequently have shale streaks of various thicknesses inter-bedded in the sand. Therefore, where shale is exposed to fluid pressure it

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson's ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young's modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott's work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger's single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966

By V. J. Sikora, T. S. Hutchinson

This paper presents a method for making a water-rlrive ana1gsis without prior knowledge of aquifer geometry and uniformity using a standard desk calculator. Although it is necessary to know the initial oil in place to use this method, this is a minor limitation to the scope of (he method since in most reservoirs it is possible to obtain reasonably accurate volumetric oil-in-place estimates. An equation is developed which relates pressure at the water-oil contact to the water influx rate as a function of time by a factor called the resistance function. The resistance function introduces the composite effect of the aquifer geometry and flow resistance disrribution. It is pointed out that the characteristic shape of this function makes it possible to start with on approximation of the function and successively improve the approximation until the correct resistance function curve is obtained. In this fashion water-drive estimates can be made without the limitation of assuming simplifed aquifer shapes and flow distributions. This is the novel feature of this development. Methods are given for extrapolating the final curve to calculate future aquifer behavior. Equations are developed for adjusting the pressures and water influx rates where it appears that possible errors in these quantities make it difficult or impossible to obtain a useuble resistance function curve without this adjustment. Application of the pressure build-up analysis techiiique to estimate. some of the aquifer properties is also presented INTRODUCTION A great many oil pools are the result of oil accumulation in some type of trap in an otherwise large and continuous porous stratum. The void space of this stratum outside of the oil pool itself is filled with water or brine. In analyzing performance of the oil pool surrounded by this water aquifer, it is quite necessary. in most cases, to include behavior of the water. When the pressure at any point in a fluid system is lowered, such as by opening a well in an oil sand, fluids in the immediate neighborhood of this point will begin flowing towards this lower pressure sink. As pressure in this area drops due to flow towards the sink, fluids from farther out will start to flow towards the lower pressure. As more and more fluid is removed from the system, the distance from the sink or well within which flow is occurring will continually increase; that is, thc region of disturbance will grow. If some rigid boundary such as a fault is reached by the disturbance, this area will cease to grow; but if some movable boundary is reached, such as a water-oil contact, the area will grow on out into the water, although rate of growth may and almost always does change. The relation between amount of pressure drop and amount of fluid flowing at any point and at any time in an aquifer depends on such factors as compressibility and viscosity of the fluids, the porosity and permeability of the rock, geometry of the whole system and withdrawal rate or pressure drop. With these factors known, it is theoretically possible to calculate the pressure-flow behavior of the system, However, in practice true solutions to the problem are next to impossible due to complexity of reservoir systems. A number of approximate methods of solution have been developed based on various simplifying assumptions. One frequent assumption is that the water-oil contact can be located and equations defining oil reservoir and aquifer solved separately by assigning values to various parameters so as to match past pressure and production history. Usually the properties of the aquifer are not known, since few, if any, wells are drilled through the aquifer; but the water influx and the pressure at the reservoir boundary are known over some time. If it can now be assumed that the aquifer is circular, pie-shaped, or linear, and that it has uniform properties, it is possible to fit a theoretical dimensionless curve to the past aquifer performance history and therefore calculate future water drive. These theoretical curves are available in the literature,1,2,3 Of course, the assumption of uniform aquifer properties is almost always somewhat in error. Fortunately, however, moderate variations from the average have little effect on behavior of the system; and, hence, the best fit of a theoretical curve is frequently satisfactory. In other cases variations in aquifer properties and geometry are large enough that none of the available theoretical curves will give an acceptable fit of the data. In these cases, methods of fitting the data with various electrical analyzers have been developed.1,2' It is the purpose of this paper to present an approach

By F. L. Fayers, J. W. Sheldon

It has been a matter of concern to the petroleum industry to determine what effect the capillary term has on saturation profiles, since these profiles determine ultimate economic oil recovery. In their original solution of the non-capillary two-phase flow problem, Buckley and Leverett&apos; showed that solutions of the two-phase flow equations became multiple-valued in saturation. Since it is physically unrealistic for saturation to have more than one value at a given position, Buckley and Leverett resolved this difficulty by introducing a saturation discontinuity or "shock". They evaluated the strength and position of the shock from material balance considerations. Recently Sheldon, Zondek and Cardwell&apos; have demonstrated that the method of characteristics can be used to solve this and related problems. Owing to capillarity it is physically unlikely that saturation shocks occur in an oil reservoir. Buckley and Leverett suggested that the effects of interfacial tensions should be included in the fluid flow equations, if the solutions are to give continuous single-valued saturation distributions. An analogy to this problem is encountered in the theory of wpersonic compressible flow where the introduction of the viscous term eliminates shock behavior. However, the mathematical form of the capillary term in the porous medium fluid flow equations differs from the viscosity term in the Navier-Stokes equation. This paper demons~rates that capillarity does eliminate the triple-valued behavior and indicates the magnitude of capillary and gravity effects on the saturation profile for a variety of systems. DERIVATION OF LAGRANGIAN AND EULERIAN FORMS OF THE DISPLACEMENT EQUATION The equations representing capillary, two-phase flow are given by applying Darcy&apos;s law and a material balance condition for each phase. The familiar Darcy and material balance equations are as follows. ^U*^0......<3, ^^r=°......c« S is the saturation of the water phase, and B the inclination of the porous medium. Pressures in the oil and water phases differ by the capillary pressure associated with the interfacial tensions, P.-P.=pAS)..........(5) where p, is determined experimentally. The porous medium is said to be oil-wet if P, > Po and water-wet if P, < Po. If the fluids are incompressible and the total volumetric flow rate, q, is constant, then v, f v,, = q...........(6) By eliminating P.. /»,, and v, from Eqs. 1, 2, 5 and 6 it follows that It is convenient to normalize the variables in the problem after the manner of Handy and Hadley% so that Eqs. 3 and 7 become where j,, = —, the fractional flow of water; (F, is a capillary pressure normalizing constant.) Substitution of Eq. 9 into Eq. 8 gives In this partial differential equation for an initial value

By B. Wilhelmi, W. H. Somerton

Simultaneous measurement of pore and elastic properties of socks under a wide range of triaxial stress conditions may be made with equipment and methods developed in this paper. Tests were run on three outcrop sandstones at several confining pressures and axial stresses up to approximately 80 percent of failure stress. The greater reduction in porosities and permeabilities occurred in the hydrostatic loading portion of the stress cycle, but substantial reductions in both properties did occur upon application of deviator (triaxial) stress. Triaxial elastic moduli were calculated from strain gauge measurements. Both Young&apos;s moduli and shear moduli were found to increase with increasing confining pressure. Poisson&apos;s ratios increased with axial stress but showed no consistent change with confining pressure. Only very general relations were observed between pore and elastic properties. The lesser decrease in porosity and permeability at higher stress values is related to increase in rigidity of rocks at higher stresses. INTRODUCTION Many investigators have studied the effects of hydrostatic stress on the properties and behavior of rocks. A few have studied the effects of triaxial stress fields on individual physical properties of rocks. To our knowledge no one has measured simultaneously pore and elastic properties of rocks under a wide range of triaxial stress conditions. This is the purpose of this work. Rocks exist in the subsurface under what Jaegerl refers to as "polyaxial" stress conditions (all principal stresses unequal). When two of the three principal stresses are equal, this is referred to as triaxial loading. The triaxial method of loading is most commonly used in modern testing work because experimental difficulties in measuring physical properties of rocks are greatly reduced over polyaxial testing. Although triaxial loading may not reproduce subsurface conditions precisely, subsurface stress conditions are never known precisely anyway. Triaxial testing would seem to be more realistic than testing under hydrostatic loading (all principal stresses equal) for application of results to subsurface problems. The objectives of this work were threefold: (1) to develop methods of measuring simultaneously pore and elastic properties of rocks under triaxial stress conditions, (2) to determine whether changes in these properties are of sufficient magnitude to be considered in subsurface calculations and (3) to attempt to relate changes in pore properties and elastic properties since they will have been measured at the same time under identical loading conditions. REVIEW OF EARLIER WORK PORE PROPERTIES Several investigators have studied the effects of stress on the physical properties of rocks. Fatt and Davis2 showed the reduction of permeability of rock with hydrostatic loading. McLatchie et al.3 and Knutson and Bohor4 related permeability reduction to compessibility of reservoir rock, again under hydrostatic loading. Wble,5 and later Redmond,6 evaluated the effects of applied radial pressure on conductivity, porosity and permeability of sandstones. In this latter work, no axial stress was applied. Dobrynin7 reviewed much of the previous work done . on the effects of overburden pressure on physical properties of rocks. He concluded that changes in physical properties are controlled to a large extent by pore compressibility of the rock. Several sets of curves developed from empirical relations are presented. These curves permit estimation of change of properties with net overburden pressure, knowing the pore compressibility and porosity of the rock. Net overburden pressure is defined as (Pe - 0.85 Pi ) where Pe is the

By T. K. Perkins, L. E. Bartlett

Values of rock surface energy (i. e. energy required to form a unit area of new surface) are useful for interpretation of drilling and fracturing phenonema This paper describes the adaptation of a cleavage technique (splitting of large rocks under controlled conditions) for measuring surface energies. Values of surface energy obtained at room temperature and at low crack extension rates are reported for a variety of sandstones and limestones. Elastic moduli, tensile strengths and compressive strengths of the samples are also reported. The values of Young&apos;s moduli (measured in bending) are relatively low, probably because of the low stress levels imposed. Measured values of surface energy me generally higher than anticipated and probably reflect inelastic yielding near the extending tip of the crack. INTRODUCTION The technology of petroleum production includes many operations such as drilling and fracturing, which involve rock breakage. One of the fundamental properties of a rock needed to fully explain breaking and fracturing phenomena is the surface energy (i. e. the energy required to form a unit area of new surface). In this paper we describe an adaptation of the cleavage method (splitting of the rock under controlled conditions) to utilize large rock samples. Application of the theory of elastic cantilever beams and the Griffith concept of mechanical stability permits the calculation of surface energies from simple measurements. Values of surface energies obtained at room temperature on dry samples and at low crack extension rates are reported for a variety of sandstones and limestones. Measured values of Young&apos;s Moduli, compressive strengths and tensile strengths are also reported for the rocks. THE EXPERIMENTAL METHOD Equipment designed to cleave large rock samples is shown on Fig. 1. This equipment consists essentially of two steel blocks cemented to a rock sample and forced apart with a steel rod. A ball joint and a pivot prevent bending stresses in the rod. A differential thread arrangement permits the rod to advance only 0.012 in./revolution of the driving nut. The axial force in the rod is measured with type FA-50-12 Baldwin Lima Hamilton strain gauges and a BLH type 20 strain gauge reader. Separation of the blocks is measured with a Starrett 656617 dial gauge. The massive nature and design of the equipment minimize the amount of elastic energy stored in the steel parts as the stress in the rod is increased. This will permit the rock to split under controlled conditions as will become clear later. Fig. 2 shows a sketch of the rock sample during cleavage. Guide slots are cut longitudinally along the rock sample as suggested by Berry.1 An initiating slot is also cut across the top of the block to a depth of 1 to 2 in. During cleavage, elastic energy is stored in the flexed beams of rock of length C. If the length of steel rod L is held constant and the crack extends in length, then the elastic potential energy stored in the rock decreases. However, surface energy must be supplied as the crack extends in length. Griffith6 has proposed the following criteria for mechanical stability. The crack will extend as long as the potential energy available is greater than the surface energy required. However, the crack will stop extending when the change in potential energy with change in crack length is just equal to the change in surface energy with change in crack length. See Eq. 1.

By L. L. Handy

The development of a theory for miscible liquid displacement requires evaluation of the variables which affect growth of the mixing zone between solvent and displaced oil. Factors which appear to be important are individual fluid viscosities, viscosity ratios, flood rate, fluid densities, flow characteristics of the porous medium and molecular diffusion coefficients of the fluid components. The primary purpose of this paper is to evaluate diffusion effects. Theoretical treatments to date have been limited to floods for which the viscosity ratio is one. Two principal theories have been proposed. Von Rosenberg adapted for porous media a theory derived for capillary tubes by G. Taylor.&apos; ,&apos; In this theory molecular diffusion perpendicular to the direction of flow is a primary factor in sharpening the flood front. Slow floods give sharper fronts for a given distance traveled than fast floods. An alternative theory considers miscible liquid displacement as a statistical problem.3,4,5 Diffusion is not an important factor in this theory, but it leads to the same general type of equation as von Rosenberg&apos;s. Both theories predict S-shaped concentration profiles with the same dependence on distance traveled. The statistical or "dispersion" theory predicts rate independence, however. To supplement rate studies a direct measurement of a diffusion effect would be helpful in evaluating which of the two proposed mechanisms best describes miscible liquid displacement for one-to-one viscosity ratio systems. No quantitative theory has been proposed for floods in which a low-viscosity fluid displaces a high-viscosity fluid. It might be anticipated, however, that the extensive fingering observed in floods with adverse viscosity ratios would increase opportunities for an exchange of components between displaced and displacing liquids by a diffusional process. Even if molecular diffusion were not an important mixing mechanism for one-to-one viscosity ratio systems, it could be significant in systems with adverse viscosity ratios. METHOD FOR EVALUATING DIFFUSIONAL MIXING In solvent flooding the displacing liquid can become mixed with the displaced liquid by a number of processes; in general, either mechanical or diffusional in character. To evaluate the contribution of diffusion, a method was sought that would distinguish diffusional mixing from mechanical mixing. Suppose two soluble tracers are added to the displacing liquid and that one tracer has a diffusion coefficient much greater than the other. Then, if diffusion is important during miscible liquid displacement and if diffusional transport is primarily transverse to the direction of flow, substances with high diffusion coefficients will have sharper concentration profiles than those with comparatively low molecular diffusion coefficients. In order to have material balance the profiles for the two tracers must intersect. For one-to-one viscosity ratios the intersection would occur at the 50 per cent concentration point. It is generally assumed that diffusion in the direction of flow is negligible. This assumption appears reasonable because flow velocities are ordinarily orders of magnitude greater than diffusional velocities. If this is not a valid assumption, however, the shapes of the fronts will be further degraded by longitudinal diffusion. The effects of rate and molecular diffusion coefficients are the opposite for longitudinal diffusion to those for lateral diffusion. Higher rates or lower diffusion coefficients would tend to give sharper fronts. The double tracer method offers several unique advantages in evaluating effect of molecular diffusion. First, the method gives a direct measure of the effect of diffusion on mixing zone size. Second, the effect of a difference in diffusion coefficients is determined from a single experiment. Comparison of several experiments at different rates is not required. Third, the method is applicable for any viscosity ratio. Fourth, the method is unaffected by density differences between the two fluids which might result in rate dependent gravity effects. EXPERIMENTAL PROCEDURE Suitable tracers are substances whose diffusion coefficients differ as widely as possible, but whose adsorptions on rock surfaces is negligible. The two tracers selected were methanol and sucrose in water solutions. The approximate diffusion coefficients for methanol and sucrose, as given in the International Critical Tables, are 1.3 X 10-5 and 0.3 X 10-5 m2/sec, respectively. Concentrations in the water solutions were 200 gm/liter of solution for both methanol and sucrose. These high

By J. A. Putnam, A. D. K. Laird

In laboratory research on the behavior of oil, gas and water in porous materials, no direct method has been devised to measure saturation without disturbing the flow. Indirect methods involving various forms of radiation have been developed for measuring one or two components. The X-ray absorption method for two components has been described previously1-3. The possibility of three component measurement has also been mentioned1. Since two component measurement still requires considerable care to insure accuracy, the fact that three components can be measured satisfactorily is not generally appreciated. The fraction of the energy of an X-ray beam of one wavelength transmitted through a material is given by the transmission factor. in which 1 is the beam&apos;s path length through the fluid. p is the fluid density, and 1,. is its mass absorption coefficient. Eq. 1 implies that all parts of the beam pass through equal amounts of the fluid. Practical applications are, therefore, limited to systems in which the fluid is distributed so that I varies negligibly over the cross-section of the beam. Typical variations of the transmission factor with X-ray tube potential arc shown in Fig. 2 from which experimental points have been omitted for clarity. The X-ray absorption of low pressure gases in a core is practically zero so it cannot he distinguished from that a vacuum by instruments that will differentiate between liquids. The transmission factor of a gas in a core is. therefore, unity. Consequently, the saturation of only one gaseous component can be found. If two fluids completely fill a core, their two saturations add to unity and, therefore, only one value of the transmission factor, T, is needed to determine both of them. When two liquids do not completely fill the core, their saturations do not add to unity and transmission factors at two wavelengths must be measured. At one of these wavelengths, 7 for one liquid must be different from T or the other liquid. The change of T for one liquid us the wavelength is changed between the two values must be different from the corresponding change of T in the other liquid. The two values of fluid saturation will also give that of the gas because the three saturations must add to unity. In Fig. 2 it can be seen that there are many large differences of T between various oil solutions and water solutions at any one potential, and between potentials for any one solution. Consequently, conditions for optimum accuracy of measurement of the saturations of a gas and two liquids can be chosen. Once the operating potentials have been selected, however. it is more convenient to cross plot the data from Fig. 2 on transmission factor-solution concentration coordinates for the chosen potentials, as shown in Fig. 3. Fig. 3 was used to plan the experimental procedure for Core N-38-1. Since the voltage control at 45 kv was good, the slopes of the curves in Fig. 2 at this potential would cause little error. At low potentials, however, the voltage control was not good, so 33 kv was chosen because the small slopes of the curves made voltage control less critical. The lowest strength beam that could be measured reasonably at 33 kv corresponded to a minimum T factor of 0.385. Fig. 3 shows that both 4.80 weight per cent of cadmium chloride in water and 24.0 per cent of iodobenzene in crystal oil had this T value, and, consequently, were indistinguishable to the X-rays at 33 kv. Thus, at 33 kv, the liquid saturation was given by the same curve regardless of the relative amounts of oil and water solutions present. This simple calibration curve from which the gas and liquid saturation can be read, is shown in Fig. 4. Fig. 3 also shows that at 45 kv, T for the aqueous solution is 0.610. and that T for the oil solution is 0.220. These values were transferred to Fig. 4 to give the triangular calibration plot from which the brine and oil saturations can be found, after the gas saturation has been determined at 33 kv.

By W. van der Knapp

A theoretical and experimental ana1ysis is given of the change in volume of a porous medium due to changes in external and internal pressures. The result enable one to deduce directly the effect of large increlents in stresses. It is shown that the three-dimensional representation of the volume of a nonlinear porous system is a cylindrical rules surface, the generating lines of Which have a slope according to the solid rock compressibility. Analytical expression for such a ,surface is very simple. It follows that the bulk and pore compressihilities depend only on the difference between pore fluid and external hydrostatic pressure, i.e., the effective rock frame pressure. From measurements on a number of sandstones as well as limestones it can be conduded that for practical values of this effective frame pressure the pore compressibility falls in the range between the compressibility of water and that of undersaturated crude oil. In general, pore compressibility is found to be higher the lower the porosity. For a particular limestone reservoir pore compressibility and porosity could he related by means of a simple empirical formula. Results from the described study find a direct applicxtion in material balance calculations and in prob1ems of liquid flow through porous media. Since the elastic constants of the rock bulk material enter into equatiorls for velocity of acoustic waves, the results are also of importance for calculating rates of wave propagation in these media. It is shown for sandstones with 1.5 to -10 prr cent porosity that laboratory measured porosities may differ from those lender reservoir conditions by about I per cent of their value. The difference for low porosity limestotnes can be of the order of 10 per cent. The subsidence caused by elastic deformation of reservoir rock is shown to he very small. General formulas relating pore and bulk volume to external and internal pressure can be derived, as has been shown by Biot1, Gassmann2 and Geertsma.2 Their theories describe the differential change in volume caused by a variation in pore fluid tension and external hydrostatic tension. It has been known for a long timei that the stress-strain relations of a packing of spheres are essentially noninear. Our experiments show that for almost all reservoir rocks which arc elastically deformable the relation between volume and loading is also a nonlinear one, resembling that of a packing of spheres very closely. The behavior of these media is often described by using the linear stress-strain relations for small incremental stresses and strains in the vicinity of a pre-stressed condition." The present study differs from these considerations in that it enables one to deduce the effect of large increments in the stresses directly. In analogy to the stress tensor for a homogeneous body the stress tensor for a porous body can be written in the conventional way: where the tensor components, o, and t, represent the total forces acting on the faces of a unit cube of porous material. This tensor can be split into two parts. a hydrostatic and a deviatoric part, as follows2,3,1 where the component of the hydrostatic stress system, a. equals The hydrostatic stress causes a change in volume whereas the deviatoric stress system gives rise to a change in shape only. One of the difficulties in describing changes of volume occurring in reservoir rocks is that the relations connecting these volume changes with external and internal stresses are essentially non-linear. A complete description requires the bulk volume, V,,, as well as the pore volume,V,,. to be known as a function of both the changes in pore fluid tension (v) and the hydrostatic tension on the outer boundary.

By R. R. Harvey

Recent evidence has indicated that the films forming at crude oil-water interfaces are the result of naturally occurring su,rface-active components in the crude oil rather than oxidation products resulting from exposure of the oil to air. Since the presence of such films may strongly affect the displacement of oil from porous media, a knowledge of their composition and formatiorz is of fundamental importance. In this study, without the assumption of a specific mechanism, film formation is considered to involve the transfer of a weakly surface-active species in solution in the oil to the oil-water interface. The film gas law and the Gibbs adsorption equation may thus he applied to the system. The rigid films which form upon decrease of the oil-water interfacial area are considered a result of the very slow rate of re-solution of the film material into the oil. When the shrinkage of the interface is very rapid, the amount of film material leaving the interface is negligible, and the system may then be treated in the same manner as an insoluble film. The combination of these treatments leads to a new concept of the film factor in which it may he quantitatively related to the concentration of film-forming material at the interface. Suitable experiments can then yield the following information. 1. Original concentration of surface-active species in the oil. 2. The change of concentration with time. 3. Concentration of surface active species at the interface. 4. The change of this concentration with time. 5. Interfacial tension of the system at any time and its variation with time. 6. Equilibriunz concentrations for a given set of conditions. 7. Concentration requirements for solid film formation. 8. Molecular diameter of the adrorbed species. These calculations may be made solely from data taken from measurements on the original oil. While using the pendant drop method of interfacial tension measurement of crude oil-water systems, Bartell and Niederhauser&apos; remarked on the thin, transparent, pliable, solid films or membranes which were often formed at the interface between crude oil and water. As a result of their observations of these films, Bar-tell and Niederhauser concluded: 1. The films are formed by material from the oil adsorbed at the interface rather than by a reaction at the interface. 2. The adsorption of the film-forming material is a rather slow process. 3. There are good indications that the process is reversible; i.e., the film constituents may re-dissolve into the oil. 4. The film will spontaneously spread over any new surface formed. 5. The process of adsorption at the interface is accompanied by a decrease in the interfacial tension of the system. Although they had proved that film formation was not due to a reaction at the interface, Bartell and Niederhauser were unable to demonstrate conclusively whether these film-forming constituents were present in the original reservoir oil or whether they were formed as oxidation products after exposure of the oil to air. Recent evidence seems to point to their presence in the original oil. Although the true nature of the film-forming constituents is still uncertain, these conditions would be fulfilled by the assumption of the presence of a slightly soluble surface-active component in the original oil. This component would migrate to a freshly formed interface because it would thereby lower the free energy of the system. The component at the surface constitutes an expanded monolayer which would become compressed, upon retraction of drop, due to the slow rate of re-solution of the film components into the bulk of the oil. It is possible, by involved extraction processes, to separate or at least concentrate this film-forming fraction. However, using the assumptions made above, the technique of monolayer film study may be applied to reveal much of the nature of the adsorbing material without resorting to an actual separation of the film-forming constituents.

By G. D. Boozer, W. H. Somerton

RESEARCH CORP., LA HABRA, CALIF. Thermal diffusivities of some typical sedimentary rocks have been measured by a rapid unsteady-state technique. Thermal data including diffusivity and conductivity are presented for the temperature range of 200" to 1,800°F. Diffusivities calculated from steady-state conductivity rneasurernents compared favorably with unsteady-state data at the lower temperatures. Unsteady-state data are less reliable at higher temperatures; reported values may be as much as 20 per cent high at temperatures in excess of 1,500°F. This is caused partly by the simplified method used in calculating diffusivity from experimental data and partly by the many thermal reactions which occur at the higher temperatures. The marked decrease in thermal diffusivity and conductivity at elevated temperatures indicates the importance of considering the temperature dependence of thermal properties in subsurface heat-transfer calculntions. Knowledge of the effects of liquid saturation, overburden and pore pressures, and heats of reaction of reservoir materials will be required before complete subsurface thermal analyses may be made. INTRODUCTION Heat-transfer calculations are becoming increasingly important in the analysis of in situ combustion and underground nuclear explosions. Thermal data for natural rock materials at elevated temperatures are generally unavailable. Calculations at high temperatures may be grossly inaccurate if temperature-dependent thermal properties of rocks are not considered. It is known that the heat capacities of rocks increase with temperature. Heat capacities may be calculated from chemical or mineralogica1 analyses of the rock system. Thermal bulk expansion of rocks is believed to be small, although few data are available. Thermal conductivities of most natural rock materials decrease with increased temperature. Thermal diffusivity, defined as the thermal conductivity divided by the product of the heat capacity and the bulk density of the material, is used in unsteadv-state heat-transfer calculations. It is apparent that thermal diffusivity decreases markedly with increased temperature. A new method, which gives a nearly continuous record of thermal diffusivity within the temperature range of 200° to 1,800°F and requires less than 1.5 hours for the run,&apos; was used to measure the diffusivity of several sedimentary rocks. Thermal conductivities were calculated from measured bulk densities, heat capacities calculated from chemical analysis and the measured diffusivity values. Thermal conductivities were measured at lower temperatures by a steady-state technique1 to test the agreement of data obtained by the two methods.

By J. M. Smith, D. Kunii

Effective thermal conductivities of sandstones filled with stagnant fluids were measured using a steady-state technique. Data were obtained for seven sandstone samples, taken from four different locations and ranging in permeability from 18 to 590 md. The measurements with gases (helium, nitrogen, air and carbon dioxide) covered a pressure range from 0.039 psia to 400 psig. Data were taken for four liquids — n-heptane, methyl alcohol, 79.8 weight per cent glycerol-water solution and pure water at atmospheric pressure. The experimental results were used to evaluate the theoretical equations for predicting stagnant conductivities developed earlier 4 The low-pressure measurements permitted evaluation of the consolidation parameter bpDp/ks (necessary to utilize the theory) for the various types of sandstones. Using these characteristic values, the tbeoretical equations correlated well with the experimental conductivity data for the several fluids and rock samples. INTRODUCTION An aspect of heat transfer in solid-fluid systems of considerable current interest is the effective thermal conductivity of porous media. The stimulus for study of the subject arises from the need for sound procedures for designing thermal methods of petroleum production. The general system occurs when there exists a flow of fluid through the pores of the solid material. However, a logical starting point in developing a theory for predicting the effective thermal conductivity in the general system is to attack the special case when the porous solid is filled with stagnant fluid. Since the flow rates anticipated in thermal production processes are very low, such stagnant conductivities k,O are also of practical significance. Kunii and Smith4 recently reviewed the existing data for stagnant conductivities and proposed a theory for heat transfer in porous rocks. This leads to equations for predicting the stagnant conductivity as a function of the properties of the fluid and solid phases. The existing experimental information1-3,5,7,8 covered a range of porosities and agreed well with the theory. However, the available data were insufficient to examine critically the effects of two important properties on koe, — the thermal conductivity of the fluid and the pressure. The objectives of the present study are twofold: (1) to measure the effect on koe of (a) the pressure for gases, and (L) the thermal conductivity of the fluid kg for bloth gases and liquids; and (2) to determine for rocks of different porosities and permeabilities the apparent solid conductivity ks and the consolidation parameter bpDp/ks required in applying the theoletical equations. Measurements extrapolated to zero pressure are helpful in evaluating ks and the consolidation parameter. However, the extrapolations must be based upon data obtained at low pressures because in small pores the molecular conductivity of the fluid may be unusually depressed. This occurs when the mean free path of the molecules is of the same order of magnitude as the pore diameter, that is, in small-diameter pores at low pressures. The phenomenon has been studied recently by Schotte6in beds of unconsolidated fine particles. With particles in the size range of 45 to 200 microns, a significant reduction of kg with pressure was found even at absolute pressures greater than 1 atm. In the sandstones employed in the present investigation, pore diameters lower than those experienced by Schotte are likely, so that the effect would presumably be greater. SCOPE OF MEASUREMENTS Stagnant conductivities were measured for four types of sandstones using a total of seven samples. The characteristics of the samples, including porosity and permeability values, are given in Table

By R. A. Salathiel, A. D. Kaiser, P. H. Monaghan, B. E. Morgan

The productivities of many hydrocarbon-bearing for-rnntions appear to be reduced during drilling, completing and repairing operations. The reason for these othcarwise unexplainable low productivities may be a drastic reduction of formation permeability immediately surrounding the borehole. A possible cause of the reduced permeability is swelling and dispersion of clays present in porous media when contacted by fresh water or mud filtrates. Hence, the invasion of fresh water or mud filtrate into hydrocarbon-bearing formations that contain clays may cause low productivities as a result of formation damage. Present laboratory investigations have yielded results which supplement existing literature on formation damage. An expanded-type clay, montmorillonite, way found in hydrocarbon-bearing formations not previously analyzed. When sand columns and formation cores containing montmorillonite were contacted by fresh water, their oil permeabilities were reduced. This reduction in oil permeability way restored partially but not completely by a repair procedure, i.e., flooding with kerosene containing organic agents or flooding with water containing electrolytes. Hence, where montmorillonite is present in formations, prevention of formation danzage was indicated to be the only complete solution to the problem. To prevernt formation damage, results suggested use of an approximately 1 per cent solution of calcium chloride or stronger solutions of sodium or potassium chloride. In conventional rotary drilling operations the wall of the hole is exposed to drilling mud for days, weeks, and in some instances for as long as several months. During this time, drilling mud filtrate seeps slowly into formations surrounding the hole. The permeability and stability of many formations, especially those containing clayey materials, are impaired by the mud filtrate. Often interaction between the mud filtrate and the formation causes drilling and production difficulties. Serious reduction in productivity of oil and gas formations during drilling, completing and repairing wells has been noted often in recent years. Cases are known of development wells which produced only small volumes of fluid upon completion. However, after a period had elapsed, they began to produce oil or gas in commercial quantities. In other cases, results of drill-stem tests taken during the drilling of deep wells have indicated good production should be obtained from shallow formations. Later difficulty has been experienced in obtaining production from these shallow formations which had remained in contact with drilling muds for an extended time. In yet other cases wells have failed to attain the productivities expected from previous performance after the use of drilling mud as a circulating fluid during workover operations. It is evident from the field behavior cited that the productivities of certain oil- and gas-bearing formations have been damaged by exposure to drilling muds. This reduction in well productivity, called "formation damage", causes serious consequences. In development wells, expensive remedial operations are incurred. In wildcat wells, good formations may appear to be marginal or even non-productive. The importance of formation damage has been recognized by a number of investigators1-s who have considered the effects of fresh water, saline solutions and aqueous mud filtrates on the permeabilities of formations. A general conclusion from such studies is that interaction between water and formation clays reduces permeability of reservoir rock and that the permeability decreases as salinity of the water decreases. Data in these references, however, concern the permeability change with only a single fluid present. A more pertinent and direct consideration in the production of oil and gas from wells is the permeability change when two fluids, oil and water, are present. Recognizing this, Nowak and Kreuger2 and Bertness1" considered several ways in which mud filtrates and saline solutions caused reductions in the oil permeability of formation cores. Investigations discussed here were designed to supplement information in the literature on changes in oil

By R. J. Wygal, J. Naar

An equation for three-phase (water, oil, gas) imbibition oil permeability is developed, assuming the water to be the dominant wetting fluid. Oil isoperms are obtained for consolidated sandstones characterized by 1/pc2 = CS*. The evolution of an oil-gas system imbibing water from Swi to(Sw,imb )max is shown to proceed along a line of constant oil saturation with increasing oil permeability and decreasing gas saturation. When the gas satuation cannot be reduced further, the system evolves along a line of constant Sg with decreasing oil saturation and permeability. The initial gas saturation is shown to reduce markedly the effect of complete wetting by either oil or water on flow performance. INTRODUCTION Imbibition oil isoperms are required for performance prediction when a well is producing water, oil and gas. This situation occurs in multiphase displacements such as underground combustion, steam injection and the water flooding of highly depleted reservoirs. In a recent paper,1 a model was presented for the prediction of two-phase imbibition characteristics. This paper extends the imbibition model to the case of three phases by assuming that the water is the dominant wetting fluid. The following results were obtained from the model: (1) an analytical expression of oil isoperms; (2) oil isoperrns as functions of reduced water, oil and gas saturations, valid for all sandstones having a capillary pressure curve which can be approximated by 1/PC = CS*; and (3) evaluation of the three-phase flow performance as dictated by complete wetting by either oil or water. The agreement between predicted and observed oil recovery in the presence of a gas phase, reported in Ref. 1, is a partial support for the present development. However, experimental data are not available at this time to check fully the model predictions. Perhaps this paper will stimulate the collection of such data. The imbibition model of a porous medium has been described previously, and the reader is referred to the paper of Naar and Henderson1 for details. In brief, the model is formed by the random interconnection of straight capillaries, with a provision for the blocking of the non-wetting phase by the invading wetting fluid. The following expressions were derived from the model. 1. The amount of oil blocked by the invading water is

By A. S. Odeh

ABSTRACT A simplified model was employed to develop mathematically equations that describe the unsteady-state behavior of naturally fractured reservoirs. The analysis resulted in an equation of flow of radial symmetry whose solution, for the infinite case, is identical in form and function to that describing the unsteady-state behavior of homogeneous reservoirs. Accepting the assumed model, for all practical purposes one cannot distinguish between fractured and homogeneous reservoirs fram pressure build-up and/or drawdown plots. INTRODUCTION The bulk of reservoir engineering research and techniques has been directed toward homogeneous reservoirs, whose physical characteristics, such as porosity and permeability, are considered, on the average, to be constant. However, many prolific reservoirs, especially in the Middle East, are naturally fractured. These reservoirs consist of two distinct elements, namely fractures and matrix, each of which contains its characteristic porosity and permeability. Because of this, the extension of conventional methods of reservoir engineering analysis to fractured reservoirs without mathematical justification could lead to results of uncertain value. The early reported work on artificially and naturally fractured reservoirs consists mainly of papers by Pollard,l Freeman and Natanson,2 and Samara.3 The most familiar method is that of Pollard. A more recent paper by Warren and Root showed how the Pollard method could lead to erroneous results,4 Warren and Root analyzed a plausible two-dimensional model of fractured reservoirs. They concluded that a Horner-type pressure build-up plot of a well producing from a fractured reservoir may be characterized by two parallel linear segments. These segments form the early and the late portions of the build-up plot and are connected by a transitional curve. In our analysis of pressure build-up and drawdown data obtained on several wells from various fractured reservoirs, two parallel straight lines were not observed. In fact, the build-up and drawdown plots were similar in shape to those obtained on homogeneous reservoirs. Fractured reservoirs, due to their complexity, could be represented by various mathematical models, none of which may be completely descriptive and satisfactory for all systems. This is so because the fractures and matrix blocks can be diverse in pattern, size, and geometry not only between one reservoir and another but also within a single reservoir. Therefore, one mathematical model may lead to a satisfactory solution in one case and fail in another. TO understand the behavior of the pressure buildup and drawdown data that were studied, and to explain the shape of the resulting plots, a fractured reservoir model was employed and analyzed mathematically. The model is based on the following assumptions: 1. The matrix blocks act like sources which feed the fractures with fluid; 2. The net fluid movement toward the wellbore obtains only in the fractures; and 3. The fractures&apos; flow capacity and the degree of fracturing of the reservoir are uniform. By the degree of fracturing is meant the fractures&apos; bulk volume per unit reservoir bulk volume. Assumption 3 does not stipulate that either the fractures or the matrix blocks should possess certain size, uniformity, geometric pattern, spacing, or direction. Moreover, this assumption of uniform flow capacity and degree of fracturing should be taken in the same general sense as one accepts uniform permeability and porosity assumptions in a homogeneous reservoir when deriving the unsteady -state fluid flow equation. Thus, the assumption may not be unreasonable, especially if one considers the evidence obtained from examining samples of fractured outcrops and reservoirs. Such samples show that the matrix usually consists of numerous blocks, all of which are small compared to the reservoir dimensions and well spacings. Therefore, the model could be described to represent a "homogeneously" fractured reservoir. la this paper, the fundamental equation of flow

Jan 1, 1966

By J. Geertsma

The relationship between porosity and the speed of propagation of acoustic waves in fluid-saturated porous rocks as measured by the Sonic log and by ultrasonic tecbniques is analyzed. Biot&apos;s continuum theory 1 is used to explain the difference in acoustic wave propagation between a dry and a liquid-saturated porous material. The porosity is a variable in this theory. However, the acoustic wave propagation in the dry rock depends too on porosity, and this dependence is not predicted by the theory. Frequently in dry sandstones, a nearly linear relationship between reciprocal acoustic wave velocity and porosity is observed in the low-porosity range. The physics behind this behavior is outlined. An empirical relationship of the form, 1/v = A + F, applies accordingly for many porous dry rocks, provided the porosity is the only variable. The presence of a liquid in the pores changes the value of B, and this change is found to be in agreement with the Biot theory. The time-average relation introduced some years ago2 results in an equation of the same type — 1/V = F/Vf + (1 - F)/Vr — but is not based on a sound physical picture. Still, this relation sometimes predicts approximately correct A and B values. Carbonate rocks with their complicated pore structures sometimes show a different relationship between wave velocity and porosity, unfavorable for log interpretation. Examples are presented. The simultaneous presence of calcite, dolomite and anhydrite, with their different grain densities and matrix compressibilities, complicates acoustic-log interpretation in carbonate rocks still further. Other complicating effects of acoustic-log interpretation are discussed. They are related to the influence of shale streaks and natural fractures on the average wave velocity observed by the logging tool and to the effect of adsorption phenomena on wave propagation in unstressed rocks particularly in sandstones. INTRODUCTION The velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity loggers of various d-sign may be used, for which velocity is defined as the. distance between a wave generator and a wave detector (one-receiver system) or the distance between two wave detectors (two-receiver system), divided by the shortest time required for a vibrational pulse to cross this distance. Velocity loggers ale used to assist in seismic prospecting, to differentiate between the various types of sedimentary rock layers, and also to determine rock porosity and pore fluid content. This paper is especially concerned with the relation between velocity and porosity and the effect of the pore fluid. Most velocity-log interpretation in terms of porosity is based on a formula advocated by Wyllie, et al,2 suggested earlier by Hughes and Jones,3 and known as the "time-average relation". This formula app1ies for a model consisting of a layered system of parallel alternating slices of a solid and a liquid, crossed by the wave path perpendicular to the interfacrbs. This must be an unsuitable model for the derivation of wave propagation properties of liquid-saturated porous media. It suggests that only rock matrix and fluid properties influence the wave velocity. The surprising fact, nevertheless, is that applications of this formula to clean sandstones under specific conditions (sufficient effective stress) results in porosity predictions which are close to reality. Other authors, such as Gassmann,4 White and Sengbush,5 Brandt,6 and Hicks and Berry,7 make use of more realistic models to arrive at a wave velocity formula for porous sediments. Their models consist of various liquid-saturated packings of frictionless spherical grains and are, therefore, also highly idealized. A number of experimental results obtained in the laboratory can be better explained with these model theories than by the time-average relation. A study of a general character, not depending a priori on a special model of the porous structure, was still lacking.

By C. Özgen Karacan

The methane emission rate into an underground mine environment from overburden strata during longwall mining is impacted by reservoir and geomechanical characteristics of the coal measure rocks in the overlying strata, as well as the presence of any coal seam. The reservoir characteristics and how they change during mining potentially affect the performance of gob gas ventholes, which consequently impacts the efficiency of methane control in the mining environment. This study presents reservoir and elastic properties of coal measure rocks in the Lower Monongahela Group in Greene County, southwestern Pennsylvania, of the Northern Appalachian Basin. Since the source of methane in this region from underground mining is located between the Sewickley coal and the Pittsburgh coal, a specific emphasis was given to this interval. Core analyses were performed in the laboratory to determine rock porosity and permeability. Geophysical logging data (gamma, density, sonic) obtained from two exploration boreholes were used for evaluating formation boundaries, shale contents, log porosities, and geomechanical properties of formations. Permeability was also calculated using density-log data and empirical equations and compared with laboratory measurements and slug tests performed in isolated intervals of boreholes. The results presented in this study can be used as data sources for reservoir studies related to the production and control of methane.

Jan 1, 2009

By S. J. Schatzel, W. P. Diamond

Longwall mining alters the fluid-flow-related reservoir properties of the rocks overlying and underlying an extracted panel due to fracturing and relaxation of the strata. These mining-related disturbances create new pressure depletion zones and new flow paths for gas migration and may cause unexpected or uncontrolled migration of gas into the underground workplace. One common technique to control methane emissions in longwall mines is to drill vertical gob gas vent holes into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important to optimize the well parameters, e.g., the borehole diameter, and the length and position of the slotted casing interval relative to the fractured gas-bearing zones. This paper presents the development and results of a comprehensive, "dynamic," three-dimensional reservoir model of a typical multipanel Pittsburgh coalbed longwall mine. The alteration of permeability fields in and above the panels as a result of the mining- induced disturbances has been estimated from mechanical modeling of the overlying rock mass. Model calibration was performed through history matching the gas production from gob gas ventholes in the study area. Results presented in this paper include a simulation of gas flow patterns from the gas-bearing zones in the overlying strata to the mine environment, as well as the influence of completion practices on optimizing gas production from gob gas ventholes.

By Luis Campos

A mediados del 2005 la empresa minera Yanacocha evaluó la posibilidad de convertir el tajo abierto de San José en un reservorio de agua que permita almacenar agua tratada durante la época de lluvias, para brindarla durante la época seca a varios canales de irrigación ubicados en las inmediaciones de nuestras operaciones, y así beneficiar a la comunidad. En ese sentido, el presente texto describe el aporte de este proyecto -en tanto representa el cambio de visión del proceso de cierre de minas, innovando a través de ideas y hechos que no han sido implementados aún por la minería de nuestro país, y aportando de esta forma a la sostenibilidad de las comunidades, luego que la minería haya culminado sus operaciones.

Sep 9, 2007