Search Documents

By R. V. Ramani

In this paper, the application of the concepts of reliability engineering to the evaluation of longwall system performance is illustrated with data from an operating longwall face. A number of cases are analyzed to highlight the impacts of longwall equipment, geological conditions and outby haulage on systems reliability and availability.

Jan 1, 1988

By Fowke NC, Williams RJ, Hungerford F

In-seam, directional drilling has been implemented at Huntly West Mine, New Zealand as the most cost effective means of obtaining geological information at a level of detail and accuracy required for planning of longwall ("flexiwall") panels. No geological or geophysical technique tried at the mine prior to 1989 has been able to reduce geological risk to an acceptable level. Surface and in-seam seismic methods have not had adequate resolution. Obtaining the required knowledge via surface drilling would be prohibitively costly, and still not precisely locate or orient faults or the axes of seam "ridges and valleys".A total of 3543 m was drilled at an average of 67m/shift including setting up time. Unplanned delays totalled only 9.6 percent. Major re-interpretation of seam structure resulted from the drilling. Lateral and longitudinal panel grades have been defined. which should be negotiable with the Coalcorp longwall equipment.

Jan 1, 1991

By W. R. Bruce, R. W. Wittkopp, R. L. Parratt

Introduction The Relief Canyon gold deposit is about 24 km (15 miles) east of Lovelock at the south end of the Humboldt Range in northwestern Nevada. The deposit, is in the Relief-Antelope Springs mining district, which has historically produced silver, antimony, and mercury. There is, however, no mention in the literature of commercial gold production. Fluorite prospects at the gold deposit site have had no reported production. At Relief Canyon, the Late Triassic Grass Valley formation overlies and is in fault contact with the Late Triassic Natchez Pass formation. Epithermal disseminated gold mineralization is found within the various types of fault breccia between these two formations. Geology The Natchez Pass formation of Late Middle to Late Triassic age is composed of more than 300 m (985 ft) of massive gray to dark gray locally carbonaceous dolomitic limestone. Some minor beds of shale and siltstone up to 1 m (3 ft) thick are found in the project area. The limestone is locally silty or sandy. The color of this formation below the oxidation base ranges from gray to black and appears to be a function of carbon content. The Grass Valley formation of Late Triassic age is composed of more than 200 m (655 ft) of interbedded units of thinly parted argillite, hard gray to brown quartzite, siltstone, and shale. Within the oxidation zone, these units are olive gray. A few beds within this formation are slightly calcareous and a number of sections, especially those containing shale, are dolomitic. Below the oxidation zone, the quartzite beds are often slightly carbonaceous and the argillite, siltstone, and shale beds are often highly carbonaceous, giving them a black color. Two types of intrusive rocks have been recognized at the Relief Canyon deposit. Both appear to predate mineralization. Fine to moderately fine grained quartz monzonite dikes, up to 3 m (10 ft) thick, were encountered in several drill holes. In a number of intervals, these dikes have undergone either propylitic or argillic alteration. The age of these types of dikes is not known. It appears, however, that they are either Jurassic or Cretaceous. No gold mineralization has been found in this type of dike. Diabase dikes were also encountered in a number of drill holes. These dikes have almost always been propylitically altered. Although the exact age of the diabase dikes is not known, they are probably equivalent in age to the quartz monzonite dikes. Quaternary alluvium is found forming fans at the base of steep slopes and as recent fill in present day drainages. The alluvium is composed of either Natchez Pass limestone or Grass Valley quartzite and siltstone, depending on which unit served as the bedrock source. A significant portion of the Relief Canyon deposit is covered by Quaternary alluvium. Figure 1 shows a generalized geologic map of the Relief Canyon area. At the deposit's site, the Grass Valley formation appears to have been thrust over the Natchez Pass formation. The age of the thrust is probably correlatable with the Nevadan Orogeny, which gives it a Jurassic-Cretaceous age. The general strike of the thrust, referred to as the Relief Fault, is in a northwest direction. The strike of the bedding of both the Natchez Pass and Grass Valley formations roughly parallel the strike of the Relief Fault. The general dip of both the Natchez Pass and Grass Valley formations is in a southwest direction. The general dip of the Relief Fault, in the area of the Relief Canyon gold deposit, varies and has the appearance of a northeast-southeast striking anticline that plunges in a southwest direction. A small fold perpendicular to the plunge of this anticline forms a dome over the southerly portion of the Relief Canyon deposit. A number of northeast and northwest trending normal faults slightly offset the Relief Fault. Because of their small displacement, they are not shown on the generalized map. Gold Mineralization Gold mineralization occurs along the highly brecciated fault contact between the Natchez Pass and Grass Valley formations. Weak gold mineralization often occurs up to 2 m (6.5 ft) above the thrust in the Grass Valley formation. Most of the ore grade mineralization, however, is present below the Grass

Jan 11, 1984

By L. W. Kempf, K. R. VanHorn

PLASTIC deformation of most commercial metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful estimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. DETERMINATION OF RESIDUAL STRESSES The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.1 Fig. I reproduces some of the data

Jan 1, 1941

By Manuel Candia

El presente trabajo describe el sistema de relleno hidroneumático realizado en el centro minero de Carahuara. La aplicación de este sistema consiste en enviar material chancado y mezclarlo con cemento y agua. Posteriormente esta carga se vierte en una tubería de alta presión, que se conecta a una bomba neumática y así enviar la carga a los tajeos que se desea rellenar. De otro lado, la ejecución de este sistema data desde 1975 a la actualidad, teniendo como antecedente la experiencia desarrollada en la mina Yauricocha de Centro Min- Perú y posibilitando su extensión a otras minas, cuyas condiciones se asemejan a la de Carahuara.

Oct 14, 1980

By Óscar Alberto Cantorín Vílchez

El relleno en pasta es un técnica que permite reestablecer la estabilidad del macizo rocoso a través del relleno tajos vacíos, de forma que se recuperen los pilares y se continúe con la explotación en niveles inferiores. En este sentido, el presente texto describe las características del relleno en pasta, descripción del proceso, y costos de operación.

Apr 1, 2013

As a result of high fuel prices and substantial haul distances or vertical lift from pits, the development of large inpit crushing and conveying systems at many open pit operations has occurred over the last decade.The basic criteria that has to be met is that the material is reduced in size to be conveyable. Generally this requires a top size of less than 300 mm.

Jan 1, 1992

By T Graham

Traditional iron ore wet beneficiation plants are large multilevel structures, often integrated into centralised processing plants. They are characterised by sizeable footprints, substantial water and power consumption, inflexible design and low scalability. Significant design changes that address these issues need to be made before relocatable modular plants become feasible. Firstly, large amounts of processing water are required in standard wet plants, so it is vital that water consumption is reduced to an absolute minimum. Secondly, the process of depositing tailings into tailings storage facilities (TSFs) is environmentally destructive, consumes significant power and requires lengthy approvals to be completed. Thirdly, modules need to be easily and quickly relocatable.The solution to reducing water usage and eliminating TSF requirements is accomplished by providing a tailings dewatering and dry-stacking capability into a separate module. This equipment needs to dewater tailings to a point (typically below 20 per cent moisture) where dry stacking becomes possible – design is mainly driven by material rheology and particle size distribution (PSD). In this respect, a flexible and scalable strategy is employed to dewatering modules, allowing a variety of components such as dewatering cyclone clusters, paste thickeners, fine mesh vibrating screens and filter presses to be used to achieve the necessary moisture level, enabling the final dry stacking to be accomplished by a simple telescopic stacking system. Plant relocatability also requires modules to comply with mass and dimensional constraints, as well as ‘plug and play’ ease-of-use features.For coarse particle upgrade, jigs provide a low-cost and effective solution, whereas fine and ultra-fine Fe units can be recovered using Wet High Intensity Magnetic Separation (WHIMS). Recently, sensor sorting – a dry process using X-ray fluorescence, X-ray transmission, laser or other sensors – has begun to make an impact in coarse particle separation, although capacities are still low. The overall objective of a plant is to provide an Fe upgrade of four to five per cent with a feed of up to 4 Mt/a and a recovery of approximately 50 per cent.CITATION:Graham, T, 2017. Relocatable modular beneficiation creates value from waste, in Proceedings Iron Ore 2017, pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

WaihiÆs Cornish Pumphouse is located on the edge of town in a dynamic and changeable area where history affects the future. As in any successful project, ingenuity and team work have been significant factors in the planning and implementation of the buildingÆs relocation.   Work around the Pumphouse site commenced circa 1900 with preparation to sink the No 5 shaft. Construction of the pumphouse and the steam driven C pump was completed by 1904 with hints of what was to come evident in 1905 as the No5 Shaft collar had sunk 350mm in four years. By 1907 surface cracking developed over the Milking Cow cave area and in 1913 200 mm was cut off the main pumping rod as the ground was sinking at a rate of 25 mm per year.   In 1913 ground around No 6 shaft had subsided 600 mm.It was also the end of an era as steam gave way to hydroelectricity and electric pumps replaced the C Pump. C Pump was maintained as a backup from 1913 to 1929 and then finally scrapped. 25 years of underground caving operations removed approximately 400 000 cubic metres of ore leaving a 7 ha collapse crater that eventually became known as the mine lake.   On the edge of town a tension zone over the Royal Lode began to develop 50 m diameter chimney collapses as large scale blocks relaxed into unfilled stopes in the old Martha underground mine. After the 1999 collapse part of the main street was closed and after the 2001 collapse Hazard Zones were declared, more streets closed and areas evacuated and retired from residential use.   By 1984 the Pumphouse has approximately one degree of tilt and in 2002 tilt on the Pumphouse accelerated briefly and then settled down. Tilt accelerated again late in 2004 and a scoping study was initiated to define protection options for the pumphouse. The Martha Mining Licence requires Newmont to 'Take whatever precautions are necessary to protect the old Cornish Pumphouse adjacent to No5 shaft' and viable solutions needed to found.   Any work on the Pumphouse comes standard with a wide range of stakeholders, governing agencies and legal framework to consider. Land Information New Zealand (LINZ) is owner and administrator of the pumphouse.

Jan 1, 2006

By Nora M. Hutt, Kevin A. Morin

One technique for controlling ongoing acidic drainage is to relocate and submerge net-acid-generating waste rock in a lake or water-retaining impoundment. This can lead to the overall improvement of water quality and the reduction In short-term environmental liabilities. A case study of this technique is the Eskay Creek Mine in northern British Columbia. Some findings of the study are: (1) the addition of lime to each truckload of rock, based on its rinse pH, neutralized the accumulated acidity and suppressed the accumulated-metal release, (2) only 10-20% of the dump's neutralization potential had been consumed when acidic drainage appeared, (3) water chemistry in the watershed recovered roughly three years after relocation, and (4) environmental liability was reduced due to the cessation of on-land acidic drainage with no degradation of lake chemistry.

Jan 1, 2000

By Steve Griles

Mr. Griles did not make his speech available for reprint. Looking Down the Road: The Environmental Side of the 1990s and Beyond Environmental Social Responsibility Love Canal, Buffalo Creek, Widow Combs, Bohpal and Three Mile Island are familiar names to all of us-names which evoke memories of environmental tragedies. These memories, as well as memories of other environmental disasters, lead us to pose this question: What is the nature of the environmental social contact between industry and society? The manner in which one answers this question will. in large measure, answer the question of where one thinks environmental issues will go, or should go, in the 1990s and beyond. The history of the evolution of the environmental movement will be helpful in defining and under- standing just what society's environmental responsibility is and, perhaps, what it will be. To Define the Future Start With the Past The common law, which most of the United States adopted from the English system of jurisprudence, traditionally considered pollution control and other environmental issues to be a matter of determining the relative rights of private property owners and of individuals. Legal and equitable theories, such as nuisance, negligence, trespass and the law of riparian rights, were utilized to allocate responsibilities between parties under the common law. The discharge of pollutants into streams and into the air was by and large considered acceptable, at least up to the point that another's "reasonable" use of the same air or waterway was significantly impeded. Further, the judicial decisions interpreting the applicability of the common law to the protection of the environment generally reflected the social and economic pressures of the age. During the Industrial Revolution, the decisions and policies had a marked tendency to favor industrial development. Jobs and industrial growth are deemed as important, and in some cases more important, than the protection of people and property. Additionally, the idea of a social responsibility, beyond that owed to a competing land or water user, was nearly alien to the early common law.' One could even go so far as to say that, had there been a social environmental contract under early common law (which, of course, there was not); but if there were, it would have been to promote actions which facilitated industrial development, even at the expense of the environment. Post-World War LI industrial expansion brought with it a growing awareness of limits on the environment's ability to absorb increasing levels of pollution. Thus evolved an era of social and political adjustment, as society began to shift away from supporting big business and industrial development and toward supporting domestic government programs and limits on industry. States gradually stepped in with efforts to address environmental issues. The Pennsylvania Clean Streams Law and the West Virginia Surface Mining Act of 1939, while lax in comparison to today's standards, nevertheless marked definitive efforts toward altering the balance between industrial development and environmental protection Pollution control continued to be viewed as a state responsibility through the 1950s, until Congress began, for the first time, to allocate funds for federal research on air and water pollution and to implement

Jan 1, 1988

By G G. Suffel

T HESE remarks on the occurrence of strata-bound massive sulphide deposits are submitted be-cause the writer recently visited the principal Cyprus deposits (in January, 1965) and has also a back-ground of many years spent largely in detailed observation and map-ping of the Horne and Amulet ore-bodies, now largely inaccessible. They are particularly related to the Symposium papers (September Bulletin) by Hutchinson and by Roscoe. Some comments are offered on the cupriferous pyrite deposits of Cyprus. As the writer is currently reviewing the published literature on the related deposits in Turkey, a brief account of some characteristic Anatolian sulphide occurrences is given. The discussion is closed with some thoughts on the relationship between these Mediterranean sulphide deposits and those of northwestern Quebec and the Superior province in general. The geology of Cyprus, as it relates to the sulphide deposits, is well summarized by Hutchinson (1965). After visiting Mavrovouni, Skouriotissa and Limni and after much thought on the possible ge-nesis of these ores, it seems quite logical to me that he is right. They are indeed closely related to late-stage submarine volcanism.

Jan 1, 1965

By George W. Maynard

IN the course of an examination of some of the California hydraulie mines in November last, I visited the property of the Gold Run Ditch and Mining Company, near Dutch Flat, Placer County. This is one of the most important and extensively worked mines in the district. The gold occurs in the characteristic blue gravel, which averages 175 feet in thickness, the lower 40-60 feet being made tip of cement gravel, which resists the action of water, and can only be loosened by blasting. The specimen which I have the pleasure of laying before the members was presented to me by Mr. I. L. Gould, the intelligent superintendent of the mines, who informs me that he found it in the old river channel, about twelve feet above the bedrock. The flattened water-worn nugget of gold, about the size of a kidney-bean, is imbedded in blue cement gravel, around which quartz has crystallized. When found the projecting portion of the nugget was enveloped in quartz, the core of gravel and gold having only been discovered after breaking the lump of quartz. On the quartz there is a shell of cement. The specimen is a remarkable confirmation of the theory of the deposition of quartz from solution. DISCUSSION. DR. T. STERRY HUNT, in commenting upon this occurrence, remarked that it is in accordance with what we already know of the recency of some of the quartz of this region, and cited the microscopic

Jan 1, 1880

By R. W. Raymond

HAVING had recently the opportunity of examining a transit and a plummet-lamp, manufactured by Messrs. Heller & Brightly, of Philadelphia, and intended for the use of mining engineers in under-

Jan 1, 1873

By J. Henry Harden

I DESIRE to call the attention of the Institute to a new form of drawing-board trestle. With the ordinary four-legged trestle, commonly used, one has not the means of adjusting the height of the board to the draughtsman. To obviate this inconvenience, and at the same time to enable one to incline the board, I have devised an arrangement of curved and straight slots and thumb-screws, by means of which the board can be raised three or more inches, and placed at any desired angle of inclination on either side. Figures 2, 3 (Plate I) show side and end elevations of the trestle for a single board, and Figure 4 for two boards. The latter form is adapted for use in schools, or where it is desired to economize space.

Jan 1, 1874

By T. Sterry Hunt

I HAVE already referred to this interesting locality in the opening address, but at the request of some of the members of the Institute, brought before them specimens of the ore and the accompanying rock. The ore, which is cassiterite, is also met with elsewhere in Maine, at Paris and Hebron, but it there occurs associated with orthoclase, quartz, tourmaline, and beryl, in concretionary granite veins, which cut the micaceous gneisses of the White Mountain series. At Winslow the veins traverse an impure gray micaceous limestone, which is found in many parts of this region, and is subordinate to the same gneissic series. The veins, which are seldom more than an inch or two in thickness, are abundant through a considerable breadth of the rock, and are interlaminated with it, occupying places between the sedimentary layers, which are distinctly marked by different shades of color. Occasionally, however, they cut across the stratification for a little distance, showing that the disrupting action was not always confined to tearing the layers apart. The vein-stone consists of purple fluor-spar, and silvery white mica with quartz. In this gangue the cassiterite, nearly black in color, is disseminated in small crystalline masses, sometimes one-half an inch in diameter, and is associated with a little mispickel. I have only seen the veins as exposed at a single point, but was informed that similar veins holding the ore are met with at a distance of several thousand feet.

Jan 1, 1873

By G. W. Brooks

This short article is quite different to the general run of papers that are presented to the Institute, but no apology is offered because I consider that first-aid and mine-rescue work are of equal importance to many other subjects that are dealt with in our Transactions. Members of the Institute should be as much interested in the safety of persons engaged in the mining industry as they are in the practical methods of modern mining. We must not only do our best to conserve life and property by adopting every known device to that end, but we must also prepare ourselves so that we may take prompt and effective action when life is in danger, or when property is subject to loss. The need for such preparation in Alberta is perhaps greater than in most places where mining is carried on, and we must spare no effort to assemble at every mine men who are well trained in first-aid and mine-rescue work. The large area over which the mines are distributed renders central training stations out of the question, hence the need for local rescue-teams. Hospitals with skilled staffs, close enough to the mines to be convenient, also seem to be out of the question; therefore the greater need of a high standard of first-aid training for the people in our mining camps. The Government mine-rescue cars are supplied with the equipment necessary for training persons in this essential work and also for dealing with disasters should they occur. The question then arises: are there a sufficient number of men who are trained ? If so we can rest assured that what is possible to be done will be done. But if a sufficient number of trained men are not available much loss of life and damage to property is likely to result.

Jan 1, 1925

The district specially referred to in this paper comprises the very gently sloping country extending from the western shores of Port Phillip from the mouth of the Yarra to Footscray along the Bacchus Marsh railway to near that town thence in a southerly direction to the Little River, and along that river to the coast, 1 as may be seen on the accompanying map. Almost the whole of this area is covered by volcanic rocks, consisting of pumerous sheets of basalt, which have been poured out of various volcanic hills in the districts, such as Mts. Atkinson and Cotteril, near Melton; Mt. Maryand Bald Hill, 12 and 16 miles respectively N.W. of Werribee; and vents in different parts of the parishes of Tarneit, Mouyong, Mooradoranook, Pyweitjorrk, and Derrimut. These volcanoes were in an active state of eruption during a late period of the earth's historyprobably the late Pliocenll, or still younger Pleistocene.Occupying a narrow strip of country, for most of the distance along the coast from Williamstown to past the mouth of the Little River, there occur deposits of still younger age, belonging to the Recent period. These lie on the basalt, and extend for distances varying from a few chains to more than a mile back from the beach. They comprise superficial deposits of blown sand, and raised beaches, composed of marine sands...

Jan 1, 1902

By T. Sterry Hunt

I HAVE lately had occasion to examine sulphuretted ores of bismuth both from Tudor, Ontario, and Latete, New Brunswick. The former consisted chiefly of bismuth-glance, carbonated at the outcrop, and within associated with some metallic bismuth, iron-pyrites and graphite, in a quartz gangue. In the second locality, where it appears to be present in considerable quantity, the veinstone is also quartz, but the associates of the bismuth-glance are chalcopyrite and galena. The treatment of such mixed ores in the furnace for the extraction of the bismuth could yield only a very impure product, and in view of the high price of the metal I tried with success a wet method for the treatment of the ore, which is based on well-known chemical reactions, and may, in some cases, be advantageously used. The pulverized ore is dissolved by heat in commercial nitric acid, and the remaining gangue washed by displacement, first with a little strong acid (which is used to attack a fresh portion of ore) and then with a moderate quantity of water, which is added to the first solution. This, if the excess of acid be considerable, may be partially

Jan 1, 1873