Search Documents

By T. W. Gonzales

The refractory performance of Peirce-Smith converters is considered to be mainly determined by effects of process control and refractory installation design. BHP Copper has shown that, over the last four years, considerable improvements in tuyere line life can be affected .by maintaining a uniform temperature in the operating converter and by ensuring sufficient and specific placement of expansion allowance in the construction of the refractory brickwork. A combination of optimized crane availability, rapid matte transfer, converter operating practices, new refractory installation techniques and applications has minimized out-of stack time. In addition, larger diameter tuyere pipes and hard piping have increased blowing rates and lowered cycle times, which has resulted in a tuyere line performance in excess of 62,500 tonnes of blister copper before maintenance is required. This paper discusses the refractory installation design changes that were made to increase tuyere line life.

Jan 1, 1999

By Charles E. Stack

There are several ways in which to classify refractories. The most suitable one is based on their general composition or raw material content. The categories are: 1. Aluminosilicate brick which include the fire clays and alumina and high alumina raw materials. 2. Basic brick which includes magnesia and chrome ore alone and in various combinations. 3. Silica brick which uses gannister or high purity gravels and sands. 4. Insulating brick are generally of the aluminosilicate type but may be most all refractory raw materials. 5. Special refractories are made from raw materials of zircon, zirconia, ultra high alumina, silicon carbide, fusion cast products, chromic oxide, carbon and graphite. The raw materials that make up these different categories are what we are briefly going to consider. Emphasis is placed more on the most important raw materials.

Jan 1, 1976

By M. DeLucia

"Over the past 15 years, technical innovations have improved the properties and performance of monolithic refractories. As these improvements have occurred, aluminum cast-house refractory selections have changed from brick to monolithic refractories supplied as either cast in place, or precast, ""Big-Block"" installations. A review of the properties of monolithic and brick refractories is presented, as well as the technical advantages of brick for highly demanding applications. Operating conditions and issues such as temperature, alloying, corundum growth and other variables are also reviewed."

Jan 1, 2004

By B. Drew, K. Budna, C. Wenzl, D. Gregurek, A. Spanring

"The metallurgy of nickel and cobalt and of copper is closely interlinked when processing sulfidic Ni-Co ores and Cu-Co ores. The respective furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear mode. This paper evaluates the common refractory wear mechanisms, namely infiltration, spalling and chemical attack by various slag systems, as well as sulfur attack, as observed when processing primary sulfidic ores. All these wear parameters, which are discussed in this paper, lead to a severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” is an important prerequisite for the refractory producer. Based on such research results, combined with specific process knowledge, appropriate brick lining solutions for nickel and cobalt processing furnaces can be recommended.INTRODUCTION The metallurgical production of cobalt and nickel and of copper is closely interlinked to the mineralogy of the respective ores: cobalt is found in African Cu-Co ores as well as in Co-rich nickel ores (laterites and sulfides). Also, Co-bearing secondary raw materials contain the mentioned elements in different contents. In pyrometallurgical processing of sulfidic ores, cobalt is generally recovered as a by-product during the production of copper and nickel, whereas it is normally not recovered separately during the processing of nickel laterites but remains in the FeNi product. Besides various hydrometallurgical production routes, the pyrometallurgical processes involved comprise smelting (i.e., production of a Cu-Ni-Co-Fe matte in electric or flash furnaces), converting and refining (i.e. removal of Fe and S as well as other elements from matte by oxidation). The ongoing trend to use higher oxygen enrichment in process air enables higher intensity processes but also increases the oxidation potential in the vessel. Therefore, during smelting and especially during the oxidative treatment in converting and refining, some amounts of valuable metals are also transferred to the slag in their oxides form. A subsequent slag treatment is then applied for recovering valuable metals from the slag, namely allowing an economic material stream handling and minimizing metal losses. This is often done in a slag reduction furnace. Additionally, copper and nickel are very good collectors for precious metals and platinum group metals (PGMs) - therefore, depending on the content of these metals, an additional refining process is used to recover these valuable metals from the matte or metal phase (Elvers et al., 1997; Davenport et al., 2002; Crundwell et al., 2011)."

Jan 1, 2017

By John Bonar

A switch to refractory-type slurry pump linings has significantly reduced maintenance costs arising from liner failure at a Missouri lead mill. The pumps routinely handle a slurry consisting of 79 to 81% solids with occasional tramp iron, and are subjected to intense abrasion which previously wore out rubber liners in anywhere from three days to two months. Average liner life at the 1.5-million-t/y (1.6-million-stpy) operation was 30 days. Experimentation with mild steel liners and even manganese steel liners failed to extend liner life beyond two months.

Jan 3, 1978

By Roselaine Gonçalves Magalhães

São apresentados e discutidos os aspectos teóricos e práticos relativos às principais propriedades físicas, térmicas e mecânicas de três refratários comerciais de MgO Al2O3 C e Al2O3 MgO C para a zona de metal de panelas de aço. Normalmente, o desgaste do revestimento dessa região é governado pela propagação de trincas, penetração de aço e sucessivo destacamento das camadas superficiais deterioradas. A deformação irreversível na direção circunferencial do revestimento também tem despertado interesse. Os resultados da caracterização laboratorial mostraram que o projeto microestrutural exerceu influência significativa nas propriedades desses refratários. Os principais fatores que concorreram para modificar o desempenho dos tijolos foram a pureza das matérias-primas, a quantidade de antioxidantes metálicos e o comportamento dimensional dos refratários. Os tijolos denominados MAC2 (MgO Al2O3 C) e AMC (Al2O3-MgO-C) apresentaram melhor compromisso entre a variação linear dimensional, resistência ao creep e resistência à propagação de trincas, exibindo, assim, maior potencial para suportar as variáveis de processos e práticas metalúrgicas vigentes na Usiminas.

Oct 30, 2017

By Roger S. Dewey

1.1. INTRODUCTION Despite indications of a general economic recovery in the U.S. during the mid-19801s, mine operators have not generally shared in the benefits of these reported better times. Budgets have not rebounded, borrowing is tougher, parent companies' pockets are not as deep as in previous years, and margins are not any better -- if there is any left over at all. Managing capital equipment budgets is always a challenge, and the last five years of stretched equipment lives make these decisions more tenuous. Delays and avoidance of replacements due to tough times inevitably makes those decisions increasingly difficult and usually more expensive The purposes of this paper are to present. a brief refresher outline of the fundamentals of equipment replacement analysis, to suggest a number of papers where analysis methods are explained in greater detail. and to recommend the use of a widespread microcomputer software capability (1-2-3) as the easiest path to a much-needed solution for a very difficult, and usually under-supported management decision problem 2. REPLACEMENT DECISION POLICY Investments in equipment replacements must compete for capital with all other investment alternatives. Capital for replacements of ten represents a greater commitment than do the new projects which a company might handle in a given year. But. sadly, formal policies for standardized analysis of replacements rarely exist, even in major companies. Yet this policy can be very significant in determining the competitiveness of a firm. Whereas many replacement decisions are based on cost minimization, economists and financial analysts agree that wealth maximization or return on investment is the superior criterion. Though the difference may seem slight, agreement on a firm's financial objective is vital. Replacement policy should be straight- forward. have a logical basis, and a proper level of sophistication. There are several reasons to develop a policy for replacement decision-making: [I] 1 - equipment's optimal economic life is nearly always shorter than its physical life; 2 - mine life often exceeds equipment life, so management must face these decisions routinly 3 - replacement capital costs, on an undiscounted basis, can run 25 to 75% of original capital 4 - technological changes may result in a newer machine or system which can operate more efficiently, more safely. or less expensively 5 - estimates should be made consistently in the fundamental areas of life expectancy, availability, utilization. price escalation, taxes 6 - long-term and short-term budgeting without decent data and analytical capability is nearly impossible, or at least ineffective Policy development assumptions which must be considered include: the planning horizon, cost patterns, interest rates, availability of capital, replacement vs. expansion, technology advances.

Jan 1, 1987

By D. Noort, M. Dawborn, D. O. del Castillo

This paper was originally presented at the North American/9th US Ventilation Symposium, June 2002, Kingston, Ontario, Canada. Reprinted with permission of the publishers, A.A. Balkema Publishers, Rotterdam, Netherlands. This paper is a study of the ventilation, cooling and refrigeration system design of the Mindola copper mine in Zambia. The challenges that were addressed varied from the restrictions imposed by an ageing infrastructure to the requirement for increasing the annual production rate, coupled to the introduction of a higher level of mechanization while maintaining acceptable conditions and limiting total ownership costs. A description of how the ventilation, refrigeration and cooling systems were modelled in order to obtain the projected heat loads associated with two different mining methods over the life of the project. The methodology included a number of iterations to optimise the design and include aspects such as the expected inrush of hot fissure water, the operation of diesel machinery at depths in excess of 1500m below surface, developing a cost-efficient cooling strategy and selection of the refrigeration machinery to meet the requirements imposed by the cooling strategy. This paper demonstrates the successful implementation of an integrated design approach.

Jan 1, 2005

By John R. Marks

The recent trend in the ventilation of deep under- ground metal mines in the United States is to rely more and more on refrigeration for air cooling. This paper describes the layout and the economics of the refrigeration method used by Hecla Mining Company at the Star Mine. An economic analysis must compare the benefits of an engineering system against the costs. The benefits of refrigeration, for example, are increased production rates, a better safety record, improved employee moral, and generally lower airflow requirements. Air-conditioning costs include capital expenditures for equipment, labor and supply costs for maintenance, and power costs for machine operation. A study of whether or not to install refrigeration becomes academic when a mine reaches the critical ventilation depth1 (the depth at which adiabatic compression alone produces station temperatures equal to the desired stope temperatures). Ventilation planning alternatives for such mines, including the Star Mine, are limited to the different methods of refrigeration usage. In this case study of the Star Mine, the refrigeration layout is described in detail. After the system performance is discussed, air-conditioning costs are calculated. The paper then concludes with a cost- benefit analysis of the Star Mine refrigeration system.

Jan 1, 1980

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"The U.S. National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. RAs typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The U.S. Mine Safety and Health Administration requires that these valves vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer, above mine atmospheric pressure in the RA. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: (1) a modified polyvinyl chloride check valve, (2) an off-the-shelf brass/cast-iron butterfly check valve and (3) a commercially available valve that was designed specifically for one manufacturer’s steel prefabricated RAs and had been adapted for use in one mine operator’s built-in-place RA. PRVs used in tent-style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with Title 30 Code of Federal Regulations, or 30 CFR, regulations. The commercially available relief valve did not meet the 30 CFR relief pressure specification but may meet the manufacturer’s specification. Alternative valve designs were modified to meet the 30 CFR relief pressure specification, but all valve designs will need further design research to examine survivability in the event of a 103 kPa (15.0 psi) impulse overpressure during a disaster. BackgroundThe Mine Improvement and New Emergency Response Act of 2006, known as the Miner Act (U.S. Department of Labor, 2006), was enacted in the wake of three mine accidents involving explosions or fire that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the Miner Act includes provisions that target mine safety issues in areas such as emergency response planning; adoption of new technology; training and education; and mine safety standards enforcement. Section 13 of the Miner Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines, and the U.S. Department of Labor to act on the results of such research, as appropriate. These mandates culminated in the 2009 adoption of changes to the Title 30 Code of Federal Regulations, or 30 CFR, mining health and safety regulations (U.S. Department of Labor, 2008), requiring underground coal mines to supply mine emergency RAs and associated components so as to provide a life-sustaining environment for persons trapped underground. Such RAs can be either selfcontained mobile units or built-in-place facilities. The regulatory changes also include provisions establishing requirements for the approval of RAs and their components by the U.S. Mine Safety and Health Administration (MSHA), among which are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One criterion for maintaining a safe RA atmosphere is the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (specified as 0.18 psi, or approximately 5.0 in. H2O), or as specified by the RA manufacturer, above mine atmospheric pressure in the RA (U.S. Department of Labor, 2008)."

Oct 1, 2016

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"The National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. Refuge alternatives typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The Mine Safety and Health Administration (MSHA) requires that the PRVs vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: a modified PVC check valve, an off-the-shelf brass/cast iron butterfly check valve, and a commercially available valve that was designed specifically for one manufacturer’s steel pre-fabricated RA and has been adapted for use in built-in-place (BIP) RAs located at one mine. PRVs used in tent style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with 30 CFR regulations. BACKGROUND The Mine Improvement and New Emergency Response Act of 2006 (Miner Act) (1) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement. Section 13 of the MINER Act specifically directed the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines, and the Department of Labor to act on the results of such research as appropriate. These mandates culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for the Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (specified as 0.18 psi, or approximately 5.0 in H2O), or at a pressure as specified by the RA manufacturer, above mine atmospheric pressure in the RA (2)."

Jan 1, 2016

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives require an air source to supply breathable air to the occupants. This requires pressure relief valves to prevent unsafe pressures from building up within the refuge alternative. The U.S. Mine Safety and Health Administration (MSHA) mandates that pressure relief valves prevent pressure from exceeding 1.25 kPa (0.18 psi), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. The U.S. National Institute for Occupational Safety and Health (NIOSH) tested a variety of pressure relief valves using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork and various sensors to determine if the subject pressure relief valves meet the MSHA requirement. Relief pressures and flow characteristics, including opening pressure and flow rate, were measured for five different pressure relief valves under a variety of conditions. The subject pressure relief valves included two off-theshelf modified check valves, two check valves used in MSHA-approved built-in-place refuge alternatives, and a commercially available valve that was designed for a steel refuge alternative and is currently being used in some built-in-place refuge alternatives. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.03 to 0.22 psi) and flow rates up to 19.3 m3/ min (683 scfm). As tested, some of the pressure relief valves did not meet the 1.25 kPa (0.18 psi) relief specification.IntroductionThe Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the United States in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement (U.S. Mine Safety and Health Administration, MSHA, 2006). Section 13 of the MINER Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives for underground coal mines. This mandate culminated in the 2009 adoption of changes to Title 30 of the Code of Federal Regulations (30 CFR) mining health and safety regulations, requiring underground coal mines to provide mine emergency refuge alternatives and associated components, to provide a life-sustaining environment for persons trapped underground. Such refuge alternatives can be either self-contained mobile units or built-inplace facilities. The regulatory changes also include provisions establishing requirements for MSHA approval of refuge alternatives and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the refuge alternatives. One specific criterion for maintaining a safe refuge alternative atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi), or at a pressure above mine atmospheric pressure, in the refuge alternative, as specified by the manufacturer when the breathable air is supplied by a fan or compressor (MSHA, 2008)."

Jan 3, 2018

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

8. Refuge Chambers 8.1 Refuge Chambers - Technical Discussion 8.1.1 Introduction As a part of the overall escape system, refuge chambers can provide a last resort when existing escapeways are blocked. These chambers are intended to provide both protection from toxic gases and a life supporting environment for a period of time before external rescue or further escape efforts can be carried out Escapeways may be blocked physically (due to cave-ins, etc), by fire, or by the presence of a toxic or oxygen deficient atmosphere. In the first two cases, the trapped miners would most likely await external rescue efforts, and hence the design of the chamber will have to consider the time durations that such efforts may take, It is also possible, in the second case, for fire fighting and fire protective equipment to be stored in the chamber so that miners may attempt their own escape. In the third case, it should be recognized that a compact, beltmounted 1-hour self-contained breathing apparatus has been developed(9), and that other, less compact equipment is available for up to 4 hours of self-contained breathing supply. If such equipment were stored in the chambers, then miners could escape by travelling from chamber to chamber, taking temporary refuge in each before proceeding to the next. 8.1.2 Background The concept of "barricading" has long been recommended for those emergencies where miners are trapped inby a fire. Barricading, which is the construction of a makeshift shelter in a crosscut or deadend, protects the entrapped miners from toxic gases and enables them to conserve a supply of air. In this manner, they can survive two or three days--hopefully enough time for them to be reached by rescue teams. In the past, many lives have been saved with this technique.

Jan 1, 1976

The process of refurbishment is not a precisely defined one. It is under- stood to mean an upgrading of a plant which is normally performed only once. The application of refurbishment in the field of materials hand- ling equipment poses particular problems because complex plants con- sist of individual components having quite different remaining service lives. For this reason, a systematic, proven procedure is proposed for the refurbishment of large materials handling equipment, designed to ensure economic implementation in accordance with the company goals. Rheinbraun2 has been using materials handling equipment since 1900, the largest units today being bucket-wheel excavators with a daily capacity of 240,000 bank cubic metres of overburden and a service weight of up to 13,500 t (metric tons). Since 1975, more than 50 large-scale refurbish- ment projects have been carried out in the company. In the process, refur- bishment has turned out to be the proven alternative to replacement of large materials handling equipment. Rheinbraun Engineering,3 a Rhein- braun subsidiary, carries out planning, consulting, and supervising work in the implementation of refurbishment projects in Germany and abroad. The most recent example is the refurbishment of Dredger 11 of the State Electricity Commission of Victoria in cooperation with Krupp-Australia, Melbourne.

Jan 1, 1989

By Eric Sturel, Ove Arup, Henry Tayler

One Triton Square was originally a six­storey commercial building with a single level basement located within the Regents Place development near Euston, London. The building was a concrete frame, with steel cores at each corner. The floorplate was approximately 72 x 72 m (236 x 236 ft) with a 36 m (118 ft} wide octagonal central atrium. The original building was well suited for extension due to relatively recent construction standards, high original live load allowances, its large central atrium, generous escape stairs provision and extensive record information. Plant space requirements at basement and rooflevel were maintained. The preferred scheme was the addition of three storeys to the existing six-storey structure and an eight-storey partial infill in the central atrium area, with a further allowance for completely filling in one or two of the lower atrium levels. This allowance was included in the design to offer enhanced flexibility to future tenants. It was clear from an early stage that the foundation load demand would increase to serve the enlarged building area, which increased the existing building floorplate by 70% or 130,000 sq ft (12,100 m2) of commercial space. Maintaining the basement headroom and accessibility for servicing plant would also be important.

Jan 1, 2024

By Henry H. Tayler, Eric Sturel

1 Triton Square was originally a six-storey building with a one-level basement located within a commercial development near Euston, London. It was designed and constructed in the 1990s and the foundation scheme comprised straight shafted London Clay piles arranged singly beneath columns. The scheme added three storeys and a five-storey infill in the central atrium area to increase the building floorplate by 70% and maintained the usability of the basement space. As the loads to support the additional floorplate area were greater than the capacity of the existing foundations, an optimised strengthening scheme of small diameter piles installed within the existing basement and a slender retro-fitted raft was installed to augment the existing piles. The re-use and strengthening of almost all of the existing foundations enabled re-use of a very high proportion of the superstructure and in approximately 35,000 tonnes of concrete and 1,900 tonnes of reinforcement and structural steelwork being re-used. The structural embodied carbon for the refurbished building scheme is estimated at an average of 136 kgCO2e/m2, achieving a Structural Carbon Rating Scheme (SCORS) “A” rating with components detailed in the paper.

May 1, 2022

By Fejes G

An integral part of the Brisbane Suburban Railway Electrification involved the relining, refurbishment and track lowering in the Roma Street, Brunswick Street and Gloucester Street double track tunnels. The design and the construction procedures had to satisfy the Queensland Railways electrification clearance and track standards and the requirements of maintaining track services through the tunnels during work. Refurbishing of the tunnel linings was carried out to extend the life of the tunnels.

Jan 1, 1981

By Aalbers J. P A

The State Electricity Commission of Victoria (SECV) operates 13 excavators, 3 travelling stackers and 4 mobile slew conveyors in their three open cuts in the Latrobe Valley. The majority of these machines have been designed and constructed to a German design code current at the date of order. The SECV has always ensured that the machines were manufactured and erected to the appropriate standards. The SECV has a policy of having all machines inspected by an independent inspector every two years. These inspections are based on those carried out in Germany. The inspections have been carried out by inspectors from Germany who have the necessary experience to do similar work in German open cuts. Major faults found during the inspections have been repaired, however,the gradual breakdown of corrosion protection system has continued. The structures on some machines have areas of bad corrosion. This, coupled with wear on major mechanical equipment, would require an extensive outage to overhaul the machines. Refurbishment of Hazelwood Power Station will result in higher levels of production and extended life for the station. This will require improvement in the total output from Morwell Open Cut (MOC). To meet this increased coal demand, the open cut equipment will need to operate more efficiently and for a longer period of life.

Jan 1, 1989

By Thomas J. Sawarynski

This paper discusses current trends of coarse and fine coal refuse disposal techniques. Emphasis is on site-specific engineering used by coal companies to tailor safe, cost effective, and environmentally sound refuse disposal system to the needs of a particular mine. Geotechnical design considerations will be discussed in relation to system performance, regulatory acceptance, and industry use.

Jan 1, 1982