Search Documents

By I. E. Lewis, W. R. Hopkins

Flowsheet improvements, such as series/parallel SX plant configurations, discontinuation of plant sumps and improved filter pumping concepts, the use of in-settler baffle systems, and the Krebs and combined mixer-settler designs offer opportunities to reduce SX plant cost. Today's plants employ permanent cathodes and mechanical stripping, and the increased capital cost can be offset by labor savings and higher current densities. The wider use of HDPE and new cell construction materials also reduce capital cost. The "Portelex" type of relocatable design embodies such new, cost-saving measures in a simple basic plant. Organic inventory and losses are reduced by new, fast-settling, hybrid organic reagents with improved kinetics and selectivity.

Jan 1, 1991

By W. R. Hopkins

Over 95 percent of the world's refined copper is now produced by electrolytic processes. The bulk of this electrolytic copper comes via the conventional route for sulfide ores of concentration, smelting and electro-refining. A rapidly increasing percentage of world production is now achieved using hydrometallurgical routes involving dissolution of the copper values from minerals, purification of the resultant leach solution by solvent extraction and finally deposition as cathodes by electrowinning. The technology can now be considered mature and this paper endeavors to summarize recent developments which, from the authors' perspectives, are important.

Jan 1, 1989

By L. W. Saperstein

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence-function-based computer program. Using an inverse application of the traditional influence-function technique, easily obtained surface displacements are used to analyze some of the complicated, expensive, and difficult-to- measure movements of the intermediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A secondary hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge-effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria, and in situ measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1988

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

The beach sand industry is the only Australian mineral industry which, so far, has used electrostatic separation on a full commercial scale. The main application of the process is for the separation of rutile from zircon. Laboratory work has demonstrated that electrostatic methods are effective for ilmenite-monazite and cassiterite-zircon separations, thus facilitating the production of high grade monazite and cassiterite products from top-strip table concentrates, but the commercial application of these processeshas been rather limited so far. Overseas, electrostatic methods are becoming more widely used for the treatment of granular material which is not amenable to flotation. The use of electrostatic separation for the treatment of ores other than beach sands has been investigated in this laboratory 1, 2, 3, and two pilot separators were built during i953 to carry out field tests. Of these, the first was an inclined feed plate separator for the removal of silica from granular lime-sand in Western Australia, the second a conductance roll separator for the removal of diamonds from alluvial gravel in New South Wales. In both cases the whole of the ore passed through the separator, not a gravity concentrate only as in beach sand practice. The two types of separator mentioned are shown diagramatically in Figs. 1 and 2.

Jan 1, 1954

By Palmer DJ, Bain JH, Pullen JB

Over the last ten years at Risdon, zinc production capacity has almost doubled. This has resulted in modifications, many of which have affected zinc deposition operating conditions in the cells. Some of these changes appeared to have affected average current efficiency to such an extent that a special investigation was initiated, using multiple regression analysis to assess historic cell unit operating para- meters. The study highlighted the importance of certain parameters in maintaining maximum current efficiency for zinc deposition from !Risdon purified solutions under conditions of !changing current density, acidity and zinc con- centrations. Maximum current efficiency was obtained only within a zinc to acid ratio in cell electrolyte of 0.45 - 0.55 and a residual zinc concentration greater than 48 g.1-1, irrespective of actual zinc concentration or The investigation also established: ieters giving minimum power consumption at termined current density; the effect of ntration changes in common impurities on nt efficiency; the existence of high s of some impurities in solids precipit- in the cells and pure solution tanks.

Jan 1, 1975

By Jonas Addai-Mensah

Despite the fact that nickel (Ni) laterites accounts for about 60 % of the world?s nickel mineralization, commercial processing of complex, low grade Ni laterite ores by conventional beneficiation (e.g. magnetic, electrostatic and flotation separation) still presents intractable challenges, particularly in heap leaching. Invariably, low grade laterite ores require aggressive hydrometallurgical techniques (e.g., highly acidic lixiviant leaching at ambient or elevated temperatures) for Ni and cobalt (Co) extraction. As a precursor to heap leaching, agglomeration of the multi-mineral phase feed particles into robust and porous granules of 4-10 m permeable bed, is essential. In the present work, several basic and applied studies of the agglomeration behavior of real Ni laterite ores and selected oxides and clay minerals (hematite, quartz smectite and kaolinite) which constitute the predominant host gangue phases of typical laterite ores are performed. Isothermal, batch agglomeration tests involving sulphuric acid solution as a binder were carried out to produce coarse, narrow-sized (5 ? 40 mm) granules which were well characterized. The influential role of feed ore characteristics (e.g., mineralogy/chemistry and primary particle size distribution) and binder composition (30 vs. 44% w/w H2SO4) and dosage (15-25 wt.%) in agglomeration behavior and granule properties were examined through several characterization techniques including granule size, compressive strength, bed percolation and re-wetting stability and 3-dimensional micro-structure analyses. Links between feed mineralogy/chemistry and size, binder formulation, agglomeration behavior, curing conditions and final granule properties and structural characteristics are established. The implications of the findings to Ni laterite plant agglomeration for enhanced heap leaching are discussed. Keywords: nickel laterite, complex low-grade ores, agglomeration, heap leaching, micro-structure

Sep 1, 2012

By I Zulkarnain, H Permana, R A. Binns

Through an ambitious but relatively low-cost program of marine fieldwork, laboratory investigations and technology-transfer and training activities, three Indonesia-Australia-led marine expeditions were undertaken aboard KR Baruna Jaya VIII between 2001 and 2003. These IASSHA (Indonesia-Australia Survey for Submarine Hydrothermal Activity) cruises have sought to discover and investigate a variety of potential ore forming hydrothermal systems in a range of tectonic settings. All cruises have been successful, both scientifically and from the point of view of training, creation of capabilities and capacity building for such research in Indonesia. Over 60 scientists and technicians from Indonesian and Australian institutions and agencies have been involved. Three new sites and a possible fourth site of hydrothermal activity were discovered in the Sangihe arc in northern Sulawesi. Surveys in the Tomini basin tested a hypothesis based on previous data which suggested this might be an isolated anoxic, brine-filled basin over 2000 m deep where igneous heat sources existed to generate hydrothermal mineralisation. The bay, however, was found to be open to adjacent deep ocean circulation, and there was no evidence of massive base metal sulfides. Subdued evidence of hydrothermal activity was found in the Sunda Strait associated with the famous Krakatau volcano and the extension of the seismically active Semangko Fault. The BANDAMIN program (Indonesia-Germany) covered a portion of the Banda arc in eastern Indonesia, and also found evidence of recent hydrothermal activity and epithermal sulfide mineralisation.

Jan 1, 2004

By T. W. H. Parker, S. B. Sadleir

ABSTRACT A comprehensive program of air flush core and reverse circulation drilling, trial mining and beneficiation test work was carried out in 1980-1982 to re-assess the potential of the Mitchell Plateau bauxite deposit. The results generally confirm previous work by Amax Corporation. The bauxite is a medium available alumina and reactive silica deposit which responds well to wet screen beneficiation. High grade pockets have developed locally, with the potential for refractory grade extraction. A major feasibility study of the Mitchell Plateau bauxite deposit was completed in 1983. Due to the unexpected severity of the downturn in the alumina market, development of the project has been deferred.

Jan 1, 1984

By R. E. Gilmore

Introduction The Sydney coal-field extends for a distance of thirty miles along the northeastern coast of Cape Breton island. At a central focal point at the tip of the south arm of Sydney harbour, seven miles or so in from the Atlantic ocean, is the city of Sydney, with Port Morien to the southeast and Sydney Mines to the north . Mining centres along the ocean coast between these points include Birchgrove, Reserve, Glace Bay, and Waterford. The field is divided into three districts or 'basins', namely, Morien basin to the south, Glace Bay in the centre, and the Lingan-Sydney Mines basin to the northeast. The eastern and western portions of the latter are known as the Lingan and the Sydney Mines basins, respectively. Six distinct coal seams are described as existing in the Morien basin, nine in the Glace Bay basin, and six in both the Lingan and the Sydney Mines basin. Although known by different names in the several basins, a definite continuity of the seams has been established.

Jan 1, 1933

By N Takamatsu

The environments surrounding the iron and steel industry have changed greatly in recent years. Reported in this paper are the technologies adopted by the Japanese iron and steel industry to fititself to change in global steel demands, degradation of iron ore and coal, prolonging service life of the facilities and requirements of energy saving. In addition, innovative technologies for CO2 emission control in iron making processes are also discussed.

Jul 11, 2011

The Court rejected the suggestion that CRAE had actively misled DMR concerning the worth of its tenements. The Court agreed that CRAE remained silent about certain significant information concerning CRAE's own tenement area. It was a significant question as to what duties CRAE'was under, given that it was in joint venture with DMR in respect of one of the tenement areas. Did that joint venture create an obligation on CRAE to disclose everything it knew? The Court said no. The Court said that the fiduciary duties were defined by the terms of the farm-in agreement between DMR and CRAE. When the Court examined the disclosure obligations within the confines of the contract, it held that CRAE had not breached those terms.

Jan 1, 1990

By C. O. Brawner

INTRODUCTION My first major involvement on a rock mine slope stability project was in 1966 after I had become a principal of Golder Brawner & Associates in Vancouver, Canada. I received a request from Kennecott to evaluate two serious rock slope failures adjacent to the concentrator on their British Columbia molybdenum property near Alice Arm, BC, which was under construction. A rock slope up to 200 ft* high had been excavated at a design angle of 700. The inspection indicated that several large blocks of about 1000 cu yd each had failed on steeply inclined joint surfaces. Stability was reduced by extensive seepage caused by heavy rainfall. In addition, considerable overbreak had occurred, indicating excessive blasting had been used to excavate the slope. A program was developed to rock bolt potentially unstable blocks that could slide on dipping discontinuities. Some rock was scaled back to the inclined joints, and drain holes were drilled to reduce water pressures. The project was completed successfully and within reasonable economics. As a result of this success, enquiries were received regarding other mining projects. This indicated the potential demand for rock slope engineering. As a result, I took one month off to meet and discuss rock mechanics and slope stability with various people internationally. These included D. Coates in Canada, E. Hoek in England, K. John and L. Mueller in Germany, M. Rocha in Portugal, and the US Bureau of Mines in Denver, CO. Early misconceptions Based on involvement in projects during the next few years, it was concluded that there were a considerable number of misconceptions that existed among some geologists and mining engineers dealing with surface rock mechanics. Some of these included: • Water is a lubricant. This is incorrect. Water reduces the shear strength along discontinuities due to buoyancy, which reduces frictional strength. It also reduces the cohesion of clayey-type rocks. • The optimum pit slope angle in rock is 45°. The optimum slope angle for safety and economics is variable and is influenced particularly by structural geology, water pressures, mine blasting practices, and the depth and degree of weathering. • The flattest angle for slope stability is dictated by the angle of repose of broken rock, about 370. Where clayey-type rocks or clayey infill in discontinuities exists, failure can occur at much flatter angles, requiring flatter slopes or artificial stabilization. • Uniaxial and triaxial tests provide the necessary shear strength parameters to design rock slopes. Most failures in rock slopes are controlled by directional discontinuities. Therefore, the direct shear test is the correct test to evaluate strength parameters for most problems.

Jan 1, 1987

By Kim Lapakko

As part of a project funded by the US EPA, through the Western Governors' Association, the recent literature on the prediction of acid drainage from metal mine wastes was reviewed. Static tests such as Acid Base Accounting, Modified Acid Base Accounting, B. C. Research Initial Test, and APP:S Test attempt to quantify the total capacities for a mine waste to produce and consume acid. In kinetic tests (e.g. humidity cells, soxhlet extraction, elevated temperature oxidation, column tests, batch reactor tests, B. C. Research Confirmation Test) mine waste samples are subjected to oxidation and the resultant drainage pH is assumed to reflect that of mine wastes dissolving in the field. This paper summarizes information presented in the recent literature on static tests.

Jan 1, 1992

Indonesia remains relatively unexplored by modern methods. The great expectations created by the rush of companies taking up Contracts of Work over large areas during the epithermal gold/ring-of-fire boom (1985-7) have not been fulfilled. This is not necessarily a reflection on the prospectivity of Indonesia; on the contrary, many of the hopeful companies were,, under-staffed and under-financed to overcome the physical and logistic problems of exploring virgin jungle.After the stock market crash of 19th October, 1987, many of the weaker companies were unable to sustain their programs or to arrange farm-outs, and they have subsequently relinquished their tenements. In some cases, little or no field work has been carried out so that many areas remain untested. This poor performance will ensure much more rigorous scrutiny of future applications by the Indonesian authorities.

Jan 1, 1990

This paper discusses the impacts that advances in metallurgy and process engineering have on minerals project execution. Ausenco's business is focused on integrating minerals processing technology and the delivery of cost effective processing plants that exceed client performance expectations. The metallurgical development is a small but critical part of this process. Metallurgical development and innovation outcomes need to be transformed into an engineered solution and that solution converted into an operating plant in a cost conscious and competitive environment. Including new or innovative processes in a project flow sheet increases a project's technical and commercial risk. However, it also gives the project, and/or the engineering company, a potential advantage over projects using mainline practices. Managing the balance between risk and opportunity has been a cornerstone of Ausenco's success in recent years. Some advances in "technology" that are discussed in the paper include: larger capacity equipment new flow sheet concepts simplification of process interfaces, and more effective project strategies The common theme is that having a new idea can be the easy bit, putting it into operation effectively involves numerous people, many interfaces and strong project management.

Sep 13, 2010

By F. L. Wilke

The use of operations research techniques and computer models has become entrenched in the mining industry, particularly in the area of mine planning. The paper considers three major areas where increasing efforts are likely to be directed in the future: the integration of multiple disciplines in a single model; the decentralization of computing capacity within a structured network; and the incorporation of sophisticated techniques such as computer aided design and artificial intelligence.

Jan 1, 1987

By J. Urosek

Since the promulgation of the Mine Safety and Heath Administration?s (MSHA?s) Final Rule on mine seals (30 CFR § 75.335(b)), which became effective on October 20, 2008, many seal designs have been approved by MSHA and constructed by the mining industry. Since the effective date of the Final Rule, several issues on the design, construction, and/or inspection of seals have been brought to the attention of MSHA. Several such issues discussed in this paper include; the directional, design-load criteria required by MSHA for 50-psi seals, 120-psi seals, and greater-than-120-psi seals; the presence of fireclay in the surrounding strata where a mine seal is to be built; the measurement of convergence of the mine opening in which a seal has been constructed; where gob-isolation seals can be used; and the importance of periodic inspection of seals.

Jan 1, 2010

By Anthony G. Grice

This paper discusses the contribution that backfill is making to the Australian mining industry and provides some information on the largest operations together with some novel applications. Each of the three major backfill types; hydraulic, rock and paste are discussed in turn with a focus on new ideas and advances in understanding, technology and operating practices.

Jan 1, 2001