Search Documents

By P. C. Thurston, T. Setterfield, D. H. Watkinson

"The Maybrun copper deposit IS In a succession of pillowed basaltic flows in the Wabigoon sub-province, northwestern Ontario. The rocks have primary flow morphologies and remarkably well-preserved crystallization textures, including quench-textured plagioclase, in spite of metamorphism to the amphibolite facies. The sulphide assemblage chalcopyrite-pyrrhotite-cubanite with minor sphalerite and pyrite is primarily in interpillow spaces and is stratabound. Basaltic rocks immediately enclosing the copper sulphide minerals have an enrichment in Fe, Mg and K and depletion in Ca and Na relative to surrounding flows. The Maybrun deposit is interpreted to have formed contemporaneously with volcanism and alteration, and was subsequently metamorphosed with the enclosing basalts.IntroductionThe association o f significant base metal accumulations with mafic submarine flows in the Archean is as yet poorly documented. Such deposits, where noted, have typically been small, and are therefore commonly over looked. The Maybrun Mine, a 2.6 x 106-tonne copper deposit in pillowed basalt, has many similarities with large, well-documented volcanogenic deposits. Given the interpretation of the Maybrun Mine to be volcanogenic in origin, there is n o reason why similar processes could not produce large deposit s. This is an important realization in an area where Archean submarine mafic rock s are very common, but frequently are examined only superficially. As gold commonly occurs in deposits such as Maybrun, even modest-sized deposits may be economic. The basalts at Maybrun are remarkable for amphibolite-facies rocks because of their extremely well-preserved delicate volcanic textures, including quench textures.The Maybrun Mine is one kilometre south of Atikwa Lake, in the Wabigoon sub-province of the Superior structural province, 75 km southeast of Kenora, northwestern Ontario, at longitude 93°35'W, latitude 49°25'N (Davies, 1973). Archean metavolcanic and metasedimentary rocks and intrusions underlie the area. Goodwin (1970) concluded that the mafic and minor felsic metavolcanic rocks, as well as the overlying metasedimentary rock s, were an eastward extension of the lower cycle of the Keewatin type section for the Lake of the Woods area. He estimated that the stratigraphic thickness of Keewatin rock s in this area is about 6900 m, of which 87% is basalt. The flows contain numerous interlayered sills, predominantly of basaltic composition; they have been extensively folded, faulted, metamorphosed to amphibolite facies and intruded by numerous felsic bodies, most importantly the Atikwa Batholith."

Jan 1, 1983

By W. L. Fink, L. A. Willey

DURING the war there was introduced a new higher strength aircraft alloy designated 75S.1,2.3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75S alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75S alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. PROCEDURE Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75S "as rolled" sheet (0.064 in. thick). The composition° was as follows: Weight Percentage Cu Mn Mg Zn Cr Al with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16 in. i.d. by ¼ -in. o.d. by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064 in. thickness over the junction and adjacent lead wires for a distance of 1 ½ in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3 in. by 9 in. by 0.064 in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75S extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of ¾ in., 2 in., 3 in. and 4 in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 ½ in. Thermocouples were peened into the bottoms of 1/8 in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1947

By Horace Knerr

IT has been shown1 that the resistance to corrosion of duralumin sheet is greatly influenced by the quenching medium used in heat treatment, or, more specifically, by the rate of cooling during quenching. The severity of corrosive attack after exposure to salt-water spray increases in the following order: DEGREE OF CORROSION, BY INSPECTION, QUENCHING MEDIUM AFTER 30 DAYS OF SALT-WATER SPRAY TEST; Water, cold (60° F.) Very slight. Water boiling Slight, but more than with cold water. Oil (70° F.) Slight, but more than with cold water. Air, fan blast, 65° F Severe, scaled. Air, still, 65° F Deeply scaled. The tensile strength, yield point and elongation are only slightly affected by the quenching medium, as shown in Table 1.

Jan 1, 1930

By R. M. Brick, Arthur Phillips, A. J. Smith

A PREVIOUS publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuA12. A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation. to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic deformation or cracking has been considered in relation to the physical properties of the alloy. On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degree of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. STRAIN IN SOLID-SOLUTION ALLOYS A 10 per cent magnesium alloy in the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using aluminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl2, CaC12, NaCl. Chill-cast rods were sealed under vacuum

Jan 1, 1935

By R. M. Brick

A PREVIOUS publication 1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuAl2. A similar study has been made of the aluminum-rich aluminum-mag-nesium alloys. Attention has been directed in the present investigation to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic deformation or cracking has been considered in relation to the physical properties of the alloy. On reheating alloys in the two-phase field, the time required for pre-cipitation to occur has been observed in connection with the degree of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys.

Jan 1, 1935

By Halet. R. A.

"The Quesabe Mine, owned by Brunston Mines Limited, is a gold deposit in the south central part of Duprat Township, northwestern Quebec, about 10 miles northwest of Noranda.It is one of the few gold mines in Canada developed since World War II. The occurrence of gold in the Quesabe fault structure has been known for many years, but serious exploration did not begin until 1945. By 1949, 15,000 feet of diamond drilling had been completed and a shaft sunk to a depth of 635 feet, with lateral development on the 450 and 600 foot levels. In 1949 and 1950 a new shaft was sunk to 1,050 feet, new levels were established at 800 and 1,000 feet, and ore was mined and shipped to the Noranda smelter. After November 1950 the ore mined was treated in the company's own mill. The grade of ore was marginal under existing economic conditions, and production was suspended in April 1952. The mine produced about 100,000 tons of ore with an average grade of approximately 0.25 ounces of gold per ton.GeologyThe bedrock formations are all Precambrian, and the general geology of the area has been described by W. G. Robinson (1). The rocks in the vicinity of the mine are acidic and basic volcanics of the Keewatin series (andesite, rhyolite, agglomerates, tuffs) invaded by the Flavrian Lake granite stock, and by dykes and irregular masses of intrusive felsite, quartz porphyry, syenite-porphyry, diorite, and lamprophyre.The mine workings are in andesite and felsite, about 2,500 feet west of the western margin of the Flavrian Lake stock.The principal structural feature of the area, from an economic point of view, is the Quesabe fault. This steeply-dipping fault cuts all the rock formations of the area, and has been traced for about 11 miles along a strike of north 65 degrees east from Lake Arnoux in the northeast corner of Dasserat Township to Duprat Lake near the east boundary of Duprat Township."

Jan 1, 1949

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By Robert B. Parsons

"In all likelihood, Canada's mining industry would be adversely affected by corporate tax reform proposals actively being considered by the Department of Finance in Ottawa. When the next set of proposals for lax reform is released later this year as promised by Finance, the mining industry had better be prepared 10 take a hard look.IntroductionTwo federal budgets ago, in May 1985, Finance Minister Wilson tabled budget papers that were more massive in terms of volume than most federal budgets. Buried in this mass of documentation is a discussion paper entitled ""The Corporate Income Tax System-A Direction For Change"". When the discussion paper was tabled over one year ago, reaction from the business sector was almost nonexistent. By and large, the paper was regarded as nothing more than one more federal publication of mild academic interest.But, recent events suggest that this discussion paper for corporate tax reform could be the cornerstone for a series of changes to the tax laws which would have more profound and widespread effects for all sectors of the economy than any reform since 1971 . No industry in Canada can afford to ignore the movement afoot in Ottawa for corporate tax reform."

Jan 1, 1986

By Robert Isaac Williams

The Questa mine is located in northern New Mexico on the western flank of the Sangre de Cristo Mountains about 75 miles north of Santa Fe and ranges in elevation from 6,800 to 10,000 ft. GEOLOGY The rocks of the area are Precambrian metamorphic rocks covered by Tertiary extrusive andesites and rhyolites and intruded by Tertiary granitic rocks. These Tertiary intrusives are localized in an east-west belt about 20 miles long and 2 miles wide, extending from Questa to Red River. The Questa orebody is associated with a north-trending aplite intrusive about 3/4 mile wide and 1 3/4 miles long. In the area of mineralization, the metasomatism of aplite has produced a mottled porphyritic rock. This hybrid rock has caused much of the controversy about the Questa mine intrusive. The orebody is essentially monomineralic and consists of numerous closely spaced molybdenite veins varying in thickness from ' 'paint" to 3 in. and occurring in both the andesites and the intrusive. In the intrusive the veins are often siliceous. Common alteration minerals associated with the molybdenite ore vary with the original composition of the rock. The alteration of the aplite has produced phenocrysts of orthoclase, albite, oligoclase and biotite; veins of quartz, orthoclase, and biotite; and graphic myrmekitic intergrowths of feldspars and quartz. In many places near the contact, the andesite is indistinguishable from the metasomatized aplite. The dominant alteration in andesite, however, is the development of fine-grained biotite with apatite, rutile, and sphene.

Jan 1, 1969

By G. S. Rice

IT is evident from Professor Louis' remarks that he holds a different opinion on certain phenomena connected with a specific type of surface subsidence from mining than is held by many engineers in the United States. The question which appears to be at issue is whether or not the line or plane of "draw" produced in ground movement resulting from extraction of pillars may, under certain conditions, be vertical or even inclined toward the workings rather than inclined for- ward over the unworked mineral, as it is universally agreed occurs in mining by the longwall advancing method. In discussing this case it is well to take the simplest condition, such as specified by Professor Louis, of a flat bed, whether it be coal, iron or other mineral, where the overburden is stratified rock and where there is no overlying quicksand. Professor Louis says in effect that his experience is that the ultimate angle of draw is always positive and inclined 5" to 15" from the perpendicular over the unwrought mineral. My experience under Illinois coal-mining conditions is that .'where longwall advancing is used the draw is always positive as Professor Louis describes it, but that in extracting of panels by withdrawal of pillars, the ground movement is manifested, after the first roof' beam break, by the forming of an unstable dome over the goave. Then subsequently, by the falling of individual slabs from the under side, the dome gets larger and higher until it breaks through to the surface of the rock., Up to this time, arch stresses buttress the rocks above the solid coal or mineral. When, however, after. the dome breaks through and the central hole - #enlarges so the arch is no longer sufficiently supported -the stratified rocks cantilever out .from over the solid unworked mineral and tend to break off in masses triangular in vertical cross-section, until the broken loose material, sliding down against the solid rock, .has such a thrust that it balances the tendency ,for the solid stratified rock to break away and slide toward the excavation.

Jan 1, 1929

By Neville G. W. Cook

The ultimate goal in rock mechanics is to make quantitative predictions of the response of rock to changes. Measured and calculated values of changes in displacements or temperatures in the rock for six different field experiments are compared using linear regression. When values of the mean compressive stresses are large compared with the values of the deviatorial stresses, linear elasticity, using values for Young's modulus from laboratory tests, provides a good predictive model. However, if the values of the mean compressive stresses are small compared with those of the deviatorial stresses the behavior and response of the rock, though systematic, is not linear. Linear heat conduction provides good predictions of changes in rock temperatures but thermal displacements are not predicted well by linear thermoelasticity.

Jan 1, 1982

THE PENNSYLVANIA STATE UNIVERSITY, 101 MINERAL SCIENCES BUILDING UNIVERSITY PARK. PENNSYLVANIA 16803 To the Editor: With respect to the Fenvessy and Schwab article, I offer the following: As thorough as the study may be, it still has a glaring weakness. The presumption of constant supply in face of falling demand - their "low growth" case - is just wrong. It does not allow for the rapid migration, by transfer and change of major, from former high-demand programs, such as mining, to programs that have more recently obtained the cachet of job security. The figures that are shown for rapid growth in mining engineering enrollments in the period 1970-1981 are, no doubt, correct and reflect a rapid inmigration of students into mining. A similar out-migration, which began in 1982, from mining to other engineering and science disciplines is not factored into their study. Given 1983-84 enrollments, which can already be documented, it is clear that the low-growth case will, by 1985, be 50% or less of 1981. I wish students would pick their majors on the basis of their own individual abilities and interests rather than rushing lemming-like to programs that are reputed to have jobs. In the end, students will have better jobs and careers if their college majors match their talents and we, in the academic side of things, will have a livelier and more dedicated student. Lee W. Saperstein Professor and Chairman of Mining Engineering UNIVERSITY OF MISSOURI-ROLLA To the Editor: I write concerning the recent article on future demand for graduates in the mining industry. The article is, unfortunately, inaccurate because of the erroneous assumptions it makes in its basic premises. To cite but two of these, class sizes will not continue at their current level, but will, in fact, alter dramatically as a function of the perceived immediate job market rather than the future trend, so that enrollments are already below those predicted. Secondly, it is patently wrong to assume that everyone who gets a degree in the mining field will continue until retirement to work in that field. People who do not have a job in the industry will get work elsewhere and often do not come back. Others will later move to different areas. My major argument, however, deals with the underlying assumptions and methodology of the survey itself, with the concomitant challenge to the subsequent conclusions. It is no great secret that the technological world is undergoing a dramatic revolution. Computer use is rapidly spreading to the point where the microcomputer will be an integral part of every mine engineer's desk. Such a tool, which for optimal benefit must be operated by knowledgeable mining engineers, will make mining much more of a science than the current level. To remain competitive, mines will increasingly rely on higher level deci-

Jan 1, 1984

By T. Alan O'Hara

"Annual mining revenue can be computed by formulae relating metal prices, smelting schedules, concentrate grade and recovery to known ore grade and an assessment of core samples. Operating costs at different daily tonnages are related to orebody shape, mining method, milling process and general plant services. Capital costs are related to sizing of mining equipment, mine development, plant-site topography, climate and accessibility, plant services and personnel housing. IntroductionA crude guide to the average 1978 cost of mine projects is shown in Figure 1, but the costs of many mine projects have differed widely from the graphed average costs of $800,000 T0.6 for underground mine/mill projects and $400,000 T 0.6 for low-grade open-pit mine/mill projects.High mine project costs and high operating costs are characteristic of open-pit mines with high stripping ratios, underground mines with thin orebodies, mills with complex metallurgy, and projects located in isolated regions with severe climate, mountainous topography, and lacking access to existing roads, towns and electric power. When none of these adverse conditions prevailed, the mine project cost was typically much less than the graphed average cost. Virtually all the conditions likely to cause high capital and operating costs are known from knowledge of the local topography, climate or accessibility, or can be assessed by tests on core samples, as soon as the orebody has been outlined by drilling .A more accurate estimate of over-all project capital cost and operating cost can be made from a summation of items of cost after judging the effect of specific local conditions on each item of capital and operating cost. This paper offers guides in judging the effect of local conditions on the sizing and 1978 cost of specific items of capital cost and operating cost and operating cost of mine projects. When the specific items of capital cost and operating cost are totaled and measured against expected net revenue and taxes over the life of the mine using the net-present-value or discount-cash-flow methods, the result should show whether the mine project development is clearly feasible, doubtfully feasible or clearly uneconomic. If the development of the mine project is clearly feasible, or probably feasible, a detailed feasibility study by experienced consulting engineers should be commissioned before any financial commitments are made; but if project development appears to be uneconomic, the time and cost of a detailed feasibility study is not warranted."

Jan 1, 1980

In high-volume mining operations, preventive maintenance programs that include standardized replacement wear parts can boost equipment availability and lower unit costs. Meeting the daily production targets depends heavily on keeping equipment working as close to full time as possible. This is the case at one medium-sized western surface coal operation producing approximately 2.7 million t/y (3 million stpy). The mine, located in western Wyoming, removes in excess of 8 million m3 (10.5 million cu yd) of highly abrasive overburden each year. According to the mine superintendent, "Abrasion at this mine is some of the worst I've ever seen. Shovel points can wear out in little more than one shift. Dozer blades some- times last two weeks, but can wear out sooner. And ripper points really take a beating. If we can replace this fast-wearing iron with small pieces that go on quickly, we think that's the way to go."

Jan 3, 1978

By JÖRG DEHNERT, PETER WINDISCH, Bernd Schönherrt, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposures of miners in Germany, especially during remediation work in old mines. The QESS is a light-weight, modular, and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil, and expanding foam. It is designed to seal off radon-rich parts of galleries within only a few minutes. Originally, the QESS was developed to protect miners against radon exposures. Then, the QESS found the attention of several mine rescue teams at a German mining conference. The Student Mine Rescue of the Technical University Bergakademie Freiberg and the Wismut Mine Rescue carried out firstmine rescue drills in Freiberg and Schlema. Additionally, a mine rescue drill was carried out by the Front Range Mine Rescue in the Edgar Experimental Mine of the Colorado School of Mines. These drills helped to improve the systemand highlighted its potential for mine rescue operations. Now, the QESS is wellsuited for small-scale mining. The QESS can be used to seal off galleries in only a few minutes to both protect miners fromradon exposures and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

Jul 23, 2020

By BERND SCHÖNHERR, JÖRG DEHNERT, PETER WINDISCH, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposure of miners in Germany, especially during remediation work in old mines. The QESS is a lightweight, modular and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil and expanding foam. It is designed to seal off radon-rich parts of galleries within minutes. Originally, the QESS was developed to protect miners against radon exposure. Then, the QESS found the attention of several mine rescue teams at a German mining conference. Some mine rescue drills by The Student Mine Rescue of the Technical University Bergakademie Freiberg, Wismut Mine Rescue and Front Range Mine Rescue helped to improve the system and highlighted its potential for mine rescue operations. Now, the QESS is well-suited for small-scale mining. The QESS can be used to both protect miners from radon exposure and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

By Edward D. Thimons

The Bureau of Mines developed a stopping design that allows the stopping to be blown down by strong blast forces without incurring any permanent damage. Trials with the new stopping, dubbed the quick-fix blowout stopping, have been conducted in the Bureau's Safety Research Coal Mine at Bruceton, Pa., and in two New Mexico uranium mines. Results have been favorable in all cases. Compared with conventional brattice stoppings or wood bulkheads, the quick-fix blowout stopping is easier and less time consuming to install, is easier to maintain, and in most cases is just as efficient an air barrier. There is same indication that the shape of the stopping makes it more resistant to blast fore s than the fabric stoppings now in use.

Jan 1, 1976

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By C. N. Schuette

THE producers of this liquid metal call it quicksilver, while the consumer generally refers to it as mercury. It is one of he seven metals that were known to the ancients. These seven were gold, silver, iron, copper, quicksilver, lead, and tin. Other metals were sometimes accidentally alloyed with some of these, but it was not until 1490 that antimony, for example, was discovered and identified as a separate metal. It is not surprising that quicksilver should have been known in ancient or even in prehistoric times, as globules of the native metal often occur in the outcrops of the ore. Furthermore, the first man to build a fire on an outcropping of quicksilver ore would probably have found globules of quicksilver in the cold ashes of his fire after it burned out. The inability to pick up the globules with the fingers would excite interest and an attempt to gather it in shells or gourds to be exhibited and traded. The ore of quicksilver is the red sulfide, cinnabar, which has been mined and used as the pigment vermilion since before the beginning of written history. In recorded history, quicksilver is first mentioned in documents by Aristotle, 384-322 B.C. Theophrastus, in 315 B.C., credited the Athenian, Callias, with the invention of methods to beneficiate cinnabar in 415 B.C. In China also there are records antedating Christ which mention both vermilion paint and the fluid metal. From these early records, it seems certain that not only was cinnabar used as a pigment in those days but also that the metal was reduced from the ore and was used for amalgamation, for gilding, and for medicinal purposes. Quicksilver mining and metal-

Jan 1, 1953

By J. C. Reed

CINNABAR was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigel1 by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County-across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done con-siderable exploration work and has retorted the high-grade ore so .obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district.

Jan 1, 1935