Search Documents

By P Krauss, S Harpalani

Methane emitted from underground coal mines, along with ventilation air and known as ventilation air methane (VAM), constitutes the largest component of coal mine methane (CMM) emissions. Atmospheric methane, on the other hand, is a potent greenhouse gas with a significant adverse impact on the atmosphere. This has led to the development of various technological alternatives for its use as an energy fuel. Techniques involving oxidation of VAM, usually consisting of very low concentrations of methane, have been validated in the past. Prominent among these technologies are the thermal and catalytic flow reversal reactors, ancillary fuel technologies, lean fuel gas turbines, and concentrators and gasifiers. However, the efficiency of any VAM utilisation technique depends on the amount and concentration of methane in the ventilation exhaust air. Therefore, quantification of VAM emission from a coal mine is the first step towards identifying the most suitable technology for its utilisation for energy production. This paper presents an evaluation of the efficacy of VAM as an energy source. It provides details of a case study aimed at developing a technique to accurately quantify VAM emission from a coal mine. It further discusses the various VAM utilisation techniques available, and presents an economic evaluation of the alternatives. Based on the findings of the study, the most feasible method for VAM utilisation is identified for the mine. The paper summarises the procedure for quantifying VAM emissions and selecting the most suitable utilisation technique.

Jan 1, 2005

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By Samanta Neves da Silva

Depósitos estratiformes são característicos por apresentarem irregularidades nos contatos entre minério e estéril, motivo que requer especial atenção no planejamento de lavra. No depósito de Bauxita em estudo, a definição da geometria da camada de minério é realizada por interpretação dos furos de sondagens com espaçamento médio de 200 metros. O modelo gerado dos contatos litológicos, comumente, não incorpora as oscilações em curtas distâncias das elevações (Z) entre furos, o que influencia na fase de modelamento geológico, logo, na previsão dos fatores de diluição e perdas de minério. Este trabalho propõe agregar dados de curta distância, aumentando as informações entre furos de sondagens e, a partir das medidas de cota no topo e base da camada de minério, melhor refletir a geometria do corpo de minério. Assim a metodologia se divide em: criar modelos de superfícies interpoladas irregulares de topo (SIT) e base (SIB), considerando as informações de curta distância; analisar elevações médias em cada superfície, a fim de pressupor superfícies planas de lavra no topo (SPT) e na base (SPB); verificar a amplitude entre essas superfícies - SITxSPT e SIBxSPB, mensurando os fatores de perdas e diluições de minério a partir da diferença entre as elevações. O produto final deste trabalho consistiu da quantificação dos fatores de diluição e perdas de minério, aplicadas ao planejamento de lavra de curto prazo, otimizando o aproveitamento dos recursos e, consequentemente, aumentando a vida útil da mina.

Aug 8, 2018

By Vitor Manoel de Araújo Silva

Os aços inoxidáveis austeníticos são materiais utilizadas nos ramos petroquímico, nuclear e aeroespacial cujas demandas se resumem essencialmente à: boa resistência mecânica, excelente soldabilidade e elevada resistência à corrosão. Apesar destes metais atenderem a estes requisitos, não raro são submetidos a etapas de conformação para elaboração de peças, o que pode modificar as suas propriedades originais. Basicamente, a causa desta mudança são alterações metalúrgicas induzidas por deformação, como a transformação da austenita (paramagnética) em martensita-a’ (ferromagnética). Tendo em vista que tais mudanças são acompanhadas de variações nas propriedades elétricas/ magnéticas destes aços, uma maneira de monitorá-los de maneira não destrutiva é através da técnica de correntes parasitas. Para este estudo, diversas amostras de aço inoxidável AISI 321 foram solubilizadas e deformadas por laminação a fim de produzirem diferentes frações volumétricas de martensita. Em seguida, submetidas à microscopia ótica, magnetômetro de amostra vibrante e correntes parasitas. De acordo com os resultados, percebe-se que toda a transformação martensítica se passa no intervalo entre 0,10 e 0,55 de deformação verdadeira. Além disso, com os dados de magnetização de saturação, foi possível estabelecer uma curva de calibração de comportamento exponencial, permitindo a quantificação da martensita de maneira não destrutiva.

Oct 30, 2017

By Tiago Luis Anderson dos Santos Morais1 Oliveira

Em função da crise energética e do aquecimento global, faz-se necessário a utilização de novas fontes de energia como uso sustentável da matriz energética disponível. Do exposto, a CEMIG GT, a ONDATEC e a Universidade Federal de Ouro Preto, investiram em um projeto no âmbito do Programa (P&D) Cemig/Aneel para geração de energia. O objetivo deste trabalho foi efetuar a avaliação do potencial energético dos efluentes gasosos (gases não condensáveis – GNC) e líquidos (Gases Condensáveis) de uma planta de pirólise de biomassa via micro-ondas para a produção de carvão vegetal. Para tanto, a ONDATEC construiu uma unidade piloto de produção de carvão vegetal (pirólise) por micro-ondas com capacidade de produção de 150 kg por hora. O processo de pirólise ocorreu em modo contínuo e em dois estágios, a secagem da biomassa e a pirólise propriamente dita, com a produção de carvão vegetal, gás de pirólise (GNC) e bio-óleo (GC). Em face dos resultados obtidos para o GC e o GNC, foi verificado um potencial de geração de 2,24 MWh de energia elétrica por tonelada de carvão produzido, que pode ser uma boa alternativa para desonerar a cadeia produtiva do carvão vegetal e do ferro gusa.

Sep 25, 2017

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

By S. Kemball-Cook, D. Heinze, A. Kornberg, M. Harmon

Climate change presents risks to mine infrastructure, operations and long-term obligations to protect environmental conditions. Management strategies and design of infrastructure and containment systems based on past or current climate conditions may be inadequate in the future if changes in climate are not taken into account in planning for mine operations, decommissioning, closure and post-closure. Data-driven assessments using climate model projections of the future can be used to quantify: • Changes in site-specific risks to mine structures, access, containment facilities, operations and staff safety. • Changes in vegetation and water balance/chemistry, and potential for acid mine drainage, erosion and design failure. Climate- and weather-related risks are a serious threat to the mining industry, but risk transfer solutions can alleviate these vulnerabilities. Mining companies can protect themselves through bespoke solutions which provide operators, investors and buyers with protection against weather-related disruptions to operations by hedging to smooth revenues. Using risk transfer structures to mitigate climate risks is a mechanism that is available to all types of mining operations world-wide. In this paper, we describe methods for evaluating site-specific climate change impacts and developing risk transfer solutions to mitigate their effects. EVALUATING MINE RISKS FROM CLIMATE CHANGE The best available tool for understanding potential future changes to the earth’s climate system are global climate models (GCMs) (IPCC, 2014). GCMs are computer simulations of the climate system which include the atmosphere, ocean, land surface, cryosphere and biosphere. Because of the computational demands of running a global model for many decades, the spatial resolutions of the GCM grids are necessarily coarse, typically on the order of 100-300 km. GCM data are therefore suitable for evaluating future physical risks on global or continental scales, but may not be appropriate for evaluating location-specific risks (e.g. Kotamarthi et al., 2016). For site-specific, quantitative physical risk assessment, GCM projection data are “downscaled” or adapted for use at the local level using statistical techniques together with observed data (statistical downscaling) or using high-resolution regional climate models (RCMs) that focus on a single geographic region and have spatial resolutions of 10-50 km (dynamical downscaling). Downscaling bridges the gap between the GCM scale and regional/local scale. Through the downscaling process, new information is added to the GCM output from observations and/or RCMs, resulting in patterns for weather variables that are more consistent with local terrain and weather influences. Downscaled climate change projections for the mine site are selected considering mine location and geography, the availability of local observations, and the performance of the downscaling method and global/regional models used to develop the projection in simulating the variable under study. Where possible, we use projections from an ensemble of global and regional model runs spanning a range of future greenhouse gas (GHG) scenarios.

Jan 1, 2019

This paper concerns a pragmatic approach to a problem that is common to many operations in the mining industry: how, over the short-term, to grasp the extent and distribution of long-term financial risk from environmental causes and reduce these risks strategically, in order to maintain stability and flexibility in the operations. Surprisingly, many companies operate without an environmental master plan or tools that can help managers measure and reduce financial risks. Such companies may be subject to unknown unacceptable financial risks from environmental causes. While many companies have some kind of internal system of environmental standards, it is often the case that such systems have uneven or limited effect, and offer no opportunities for visualising, measuring or managing aggregate financial risks from environmental causes. `Aggregate risks' are defined here as the calculated total expected financial costs to a company, or a subdivision of a company, from environmental causes at nominated operations over a defined time period. Aggregate risks take into account the type and magnitude of an environmental problem set, the likelihood of occurrence, and the time frame during which the problems will develop or solutions are required. For the large corporation, the 'amount of' aggregate environmental risk is a statistic that can be managed, along with other financial parameters, at the corporate level to improve the stability and predictability of operations, and protect the interests of shareholders. This paper concerns development of a management framework and a tool for the large corporation that responds to the need for managing aggregate environmental financial risks. The logical framework proposed to overcome the need for strategic vision is the Environmental Master Plan, and this is described in the next section. The analytical tool proposed to measure aggregate risks and provide relevant data and insights to managers, is called an Environmental Risk Management Information System, and its mechanics are described in a subsequent section.

Jan 1, 1994

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By Mustafa Kumral

Monte ? Carlo simulation is often used to assess the risks associated with uncertain variables in mining operations. The success of Monte-Carlo simulations depends upon reproducing the dependencies among variables to some extent. However, some variables may exhibit different dependency patterns. In these cases, classical techniques for dependency quantification cannot capture dependencies. As an alternative, the copulas allow modeling nonlinear dependencies. Furthermore, any choice of marginal distributions can be used. Especially, for the data, which is sensitive to extreme case such as financial crisis, the copulas arise as a means to reproduce the correlations among variables. In this paper, the copulas are introduced to mining practitioners using Monte-Carlo simulations for risk assessment. Then, a case study is given to show the superiority of the copulas over classical techniques using ModelRisk Software. In conclusion, it was observed that the copulas enhance the quality of Monte-Carlo simulations by capturing variable dependencies.

Aug 1, 2013

By A Jewbali, J Phillips, C Boyle

Normal practice in the mining industry is the creation of a single geological model. These models provide a single interpretation of the geological and mineralisation domains. These interpretations infer the exact behaviour of ore domain contacts at shorter scales when resource definition drilling is done on wider scales and are thus locally highly uncertain. The interpreted geological model provides a single number for the volume and tonnes of mineralised material enclosed by the mineralisation envelope. It is on this single number for volume and tonnage that capital intensive mine development decisions (mine design and scheduling, stockpile strategy, waste management, closure planning, dewatering strategy, product quality, etc) are based. Some of these decisions require knowledge of grade variability for small volumes of material such as quarterly production periods. It is generally recognised that this information cannot be derived from single kriged geological models, but can potentially be modelled by conditional simulation techniques. Uncertainty in the extent and continuity of the mineralised envelope and its effect on grade variability for shorter production periods is thus recognised as a major source of uncertainty in new mine development.CITATION:Jewbali, A, Boyle, C and Phillips, J, 2013. Quantifying domain uncertainty for an iron ore deposit, in Proceedings Iron Ore 2013 , pp 157-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By E Amini, M Scott

Grade Engineering® involves the planning, integration and operation of coarse preconcentration techniques to reject uneconomic material as early as possible in the mining value chain to improve the quality of ore delivered to mineral processing activities. These preconcentration techniques include screening for natural and induced deportment of grade to finer size fractions during blasting and coarse breakage, sensor-based measurements of grade and mechanised sorting at particle or bulk scales and coarse gravity separation. Over the last decade, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE), with the support of its participants, has developed a framework for the holistic evaluation of economic and production impacts attributable to these preconcentration techniques. The framework combines the characterisation of preconcentration responses, geostatistical modelling, process modelling and simulation of downstream and upstream production impacts and the optimisation of strategic mine plans to quantify changes in net present value due to different preconcentration strategies. This framework has been applied to evaluate preconcentration techniques at numerous metalliferous operations and can also be used to quantify changes in the environmental metrics for energy, water and steel consumption and emission, tailings and waste rock production. This paper collates the results of these Grade Engineering® studies to show the range and magnitude of economic and environmental impacts attributable to preconcentration. The studies have shown that rejection of uneconomic material prior to mineral processing activities can have a pronounced improvement in energy, water and comminution steel productivity, emission intensity and the profitability of metalliferous mining.

Nov 10, 2020

By Robert L. Runkel, Kenneth E. Bencala, Briant A. Kimball

Thousands of abandoned and inactive mines are located in environmentally sensitive mountain watersheds. Cost-effective remediation of mining sites in these watersheds requires knowledge of the most significant sources of metals to surface waters. The significance of a given source not only depends upon the concentrations of a toxic metal, but also on the total mass, or load of metal added to the stream. To determine loads, we combined tracer-injection methods, to provide reliable discharge measurements on a watershed scale, with synoptic sampling, to provide spatially detailed concentration data. The resulting load profiles indicate which sources have the greatest effect on streams, where natural attenuation of metal loads occurs, and where ground-water inflows are located. This is part of the information needed for planning remediation of mine-drainage effects. The approach is illustrated by comparing zinc loading curves from three watersheds affected by mine drainage.

Jan 1, 2000

By R. Zhang, S. Azam, S. Liu, J. H. Golbeck, V. Kurashov, S. Bhattacharyya

Free radicals (FRs) present in coal dust directly influence the interaction behavior between lung cells and dust particles. FRs are atoms or groups containing unpaired electrons, with strong chemical reactivity and a short lifespan. FRs which are quite persistent in natural environments, termed environmentally persistent free radicals (EPFRs), have recently received much attention as new environmentally hazardous substances. EPFRs present on coal dust serves as an active intermediary to catalyze reactive oxygen species (ROS) production by oxygen molecules endangering mine workers’ health. Many EPFR species may be bonded to the particle surface or trapped within the particle during coalification and can be modified with progressive size reduction through cutting at the mining face or crushing/pulverization in the plant. This study measured EPFRs for lignite, sub-bituminous, and anthracite coal dust at various sizes. We especially focused on EPFRs for submicron coal dust prepared by cryogenic methods. The outcome of this study will directly improve the free radical-dependent toxicity quantification and ultimately contribute to the size-dependent coal dust toxicity quantification.

Mar 2, 2022

By S M. Mousavi

The issue of estimating evaporation in soils is central to the design of engineered soil caps for mine waste and landfill applications. In general, because evaporation from the soil is difficult to measure in the field, laboratory experiments and empirical methods have been used. Much of the earlier work has been conducted in soil science, although in recent years, geotechnical and geoenvironmental engineers have given great deal effort to this work. The result of this increased interest is the development of numerical models, such as UNSATH and SoilCover for estimating evaporation. In this study laboratory-measured evaporation from soil columns was compared with evaporation predicted using the computer program SoilCover, and the analytical method proposed by Gardner and Hillel. Good agreement among the results was observed. Also the sensitivity of the predicted evaporation to soil hydraulic and geotechnical properties, such as saturated hydraulic conductivity and coefficient of volume change was discussed and the practical implication of the sensitivity were highlighted. The work has application in the design and construction of soil covers over sulfide-bearing mine waste and landfills.

Jan 1, 2003

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

By E. Ghali

"Corrosion of support system components (e.g., bolts, mesh, plates) is a safety and economic concern in underground mines. This paper reports the results of a five-year study wherein corrosion coupons were installed at select locations in participating mines, recovered at regular intervals, analyzed for signs of corrosion, and tested to quantify loss in capacity. Complementary tests were conducted on recovered mesh and friction bolt specimens. The data provide insights into contributing factors for support systems corrosion, which aid in the selection of appropriate support strategies and reliable assessment of the useful life and need for rehabilitation of a support system.RÉSUMÉ La corrosion des composantes des systèmes de soutien (p. ex. boulons, grillages et plaques) est une préoccupation économique et de sécurité dans les mines souterraines. Cet article présente les résultats d’une étude de cinq ans pendant laquelle des coupons de corrosion ont été installés à des endroits spécifiques dans les mines participantes; ces coupons ont été retirés à des intervalles réguliers, analysés pour des signes de corrosion et mis à l’épreuve pour quantifier la perte de capacité. Des essais complémentaires ont été effectués sur les grillages récupérés et sur les échantillons de boulons d’ancrage. Les données aident à comprendre les facteurs qui contribuent à la corrosion des systèmes de soutien, ce qui est utile dans le choix de stratégies appropriées de soutien et pour une évaluation fiable de la durée de vie utile et du besoin de remise en état d’un système de soutien."

Jan 1, 2015

By S. J. Neethling

"Liberation is a key driver in all mineral separation processes as it limits the maximum possible grade for a given recovery. In flotation, this is further complicated by the fact that it is surface exposure of the floatable minerals that determines the ultimate performance. Liberation, grade and surface exposure are commonly quantified using Scanning Electron Microscopy coupled to Energy Dispersive X-ray spectroscopy (SEM/EDX) analysis of polished sections. The intrinsically 2D nature of this technique can result in significant sampling errors and stereological effects that can affect the quantification of the ore’s textural characteristics. X-ray micro-Tomography (XMT) is an imaging method that can non-invasively and non-destructively delineate ore fragments in 3D, thus providing an alternative method that eliminates the need for stereological corrections and readily provides surface exposure. A methodology and automated algorithm were designed for extracting this information from images of closely packed particles, thus allowing samples containing a large number of particles to be assessed.The main drawback of XMT is that, unlike SEM/EDX, it cannot directly measure the mineralogy of the sample, instead producing a 3D X-ray attenuation map. We therefore also present an algorithm for calibrating the thresholding of the XMT images based on SEM/EDX images of sections through the same sample, thus allowing the liberation analysis to be carried out on a 3D mineral map in which the uncertainty in the mineral assignment is small and statistically quantified.The methodology was tested on low grade porphyry copper ore as this is both an industrially relevant and traditionally difficult system to quantify using XMT due to the similarity in the X-ray attenuation of the sulphide species, especially the pyrite and chalcopyrite. As each 3D volume imaged contain 100-1000s of grains, large data sets can be readily produced. By dividing these particles into classes based on both their surface exposure and grade, the extent to which there is preferential breakage of the particles can be assessed—an important consideration if sufficient surface liberation for good flotation performance is to be achieved at coarser particle sizes. It is also shown that erroneous conclusions can be drawn when basing the analysis on 2D sections through the particles."

Jan 1, 2018