Search Documents

By N. V. Peterson, R. S. Mason

Pumice, pumicite, and cinders are all products of explosive volcanic eruptions. Pumice and pumicite are produced by the violent expansion of dissolved gases in a viscous silicic lava such as rhyolite or dacite. Pumice is a light-colored, cellular, almost frothy rock made up of glass-walled bubble casts. It may occur as coherent, massive blocks composed of highly vesicular glassy lava in either a flow or vent filling, or it may be more or less fragmented by violent eruption. Pumicite has the same origin, chemical composition, and glassy structure as pumice differing only in particle size. Particles less than 4 mm in diam are designated pumicite. Pumice is usually found relatively close to the vent from which it was erupted while pumicite may be carried by winds for great distances before settling as an accumulation of fine-grained ash or tuffaceous sediment. Volcanic cinders are the reddish to black vesicular fragments that pile up during explosive eruptions of volcanoes of basaltic composition. Most deposits of cinders occur as cones or mounds of stratified fragments that range in size from a fraction of an inch to several inches in diameter. Individual cones or mounds of cinders may be several hundreds of feet in diameter and as much as 500 ft high. Properties The properties that make pumice and pumicite useful in industrial applications include: low-bulk density, good heat and sound insulating properties, and excellent abrasive capability. Cinders, even though less cellular and somewhat heavier, also have a variety of industrial uses. Uses The main use of pumice and cinders continues to be in the construction industry as road-surfacing material, railroad ballast, building block aggregate, in lightweight structural concrete, and as plaster aggregate. Both pumice and pumicite continue to be used as abrasives for polishing glass, metal, leather, stone, and wood. Some scouring powders and soaps also contain pumicite. Minor uses include fillers, absorbents, carriers for insecticides, catalyst carriers, filters, and soil conditioners. Pumicite is also used in sizable quantities as a pozzolanic additive in monolithic concrete where it increases the workability, strength, and durability of the concrete and reduces the heat of hydration. Volcanic cinders are generally denser and more coarsely cellular than most pumice. Markets for cinders include aggregate for road construction and surfacing and in lightweight concretes, particularly blocks. Some producers having access to both pumice and cinders offer a variety of blends of the two materials to block manufacturers. Most pumice deposits are unconsolidated and usually have a minimum of overburden. Mining is by open pit and can be easily carried out with conventional loading equipment. Sometimes air-drying precedes hauling to a crushing and screening plant which yields the size product desired. Multiple bins at railroad hauling facilities permit blending if desired. Pumice for abrasive use may require more sophisticated processing by fine grinding and air classification before being bagged for market. Block pumice in economic quantity and quality is limited to a few geologically young

Jan 1, 1975

By N. V. Peterson, R. S. Mason

The violent explosion of Mount St. Helens in the state of Washington on May 18, 1980 showered volcanic ash over vast areas of the Northwest. It was another eruptive episode in a long history of similar occurrences in the region, which extends from Canada to California and reaches several hundred miles inland from the Pacific Ocean. Pumice, pumicite, and cinders are products of explosive volcanic eruptions. Pumice and pumicite are produced by the violent expansion of dissolved gases in a viscous silicic lava such as rhyolite or dacite. Scoria is the mafic counterpart of pumice. Pumice is a light-colored, cellular, almost frothy rock made up of glass-walled bubble casts. It may occur as coherent, massive blocks composed of highly vesicular glassy lava in either a flow or vent filling, or it may be more or less fragmented by violent eruption. Pumicite, the diminutive of pumice, has the same origin, chemical composition, and glassy structure, differing only in particle size. Particles less than 0.16 in. in diam are designated pumicite. Pumice usually is found relatively close to the vent from which it was expelled, while pumicite may be carried by winds for great distances before settling as an accumulation of fine-grained ash or tuffaceous sediment. Mount St. Helens lofted an estimated 5 billion cu yd of ash and pumicite. The volcano, unlike most of the High Cascade peaks, is composed largely of dacitic material with only minor amounts of andesite and basalt. Volcanic cinders are the reddish to black vesicular fragments which pile up during explosive eruptions of volcanoes of basaltic composition. Most cinder deposits occur as cones or mounds of stratified fragments ranging from a fraction of an inch to several inches in diameter. Individual cones or mounds may be several hundred feet in diameter and up to 500 ft high. Properties and Uses Low bulk density, good heat and sound insulating properties, and excellent abrasive capabilities make pumice and pumicite useful in industrial applications. Cinders, though less cellular and somewhat heavier, also have a variety of industrial uses. The main use of pumice and cinders continues to be in the construction industry as road-surfacing material, railroad ballast, and building block aggregate. Pumicite is used in sizable quantities as a pozzolanic additive to monolithic concrete where it increases workability, strength, and durability of the concrete and reduces the heat of hydration. Volcanic cinders generally are denser and more coarsely cellular than most pumice. Markets for cinders include aggregate for road construction and surfacing and use in lightweight concretes, particularly blocks. Some producers having access to both pumice and cinders offer a variety of blends of the two materials to block manufacturers. Table I lists the principal applications of industrial pumice. Tables 2 and 3 show US sales and uses of volcanic products. Most pumice deposits are unconsolidated and usually have a minimum of overburden. Mining is by open pit and can be easily carried out with conventional loading equipment. Sometimes air drying precedes hauling to a crushing and screening plant which yields the size product desired. Multiple bins at railroad hauling facilities permit blending if desired. Pumice for abrasive use may require more sophisticated processing by fine grinding and air classification before being bagged for market.

Jan 1, 1983

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By Robert E. McIvor

"The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out.The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, “Circuit Classification System Efficiency” (CSE), is the fraction of “coarse” material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of “fines” or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable target CSE for any given circuit can be estimated, for example, by referring to a plant data base of CSE’s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE.This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “Circuit Classification System Efficiency” (or CSE, McIvor, 1988a), and subsequently the discovery of the Functional Performance Equation (McIvor, 1988b; McIvor et al, 1992). The CSE is the fraction or percentage of “coarse” (usually in reference to the plus P80) size material inside the mill, versus “fines” or product size material finer than the circuit P80. It can be readily calculated by taking the average of the percentage of said coarse material in the mill feed and mill discharge streams. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, for which the derivation has often been presented (e.g. McIvor, 2006)."

Jan 1, 2011

A pilot pump rehabilitation programme commenced at Isa Mine in the late 1960ts. Over the years, it has now been developed into a full scale repair programme resulting in large operating cost savings. This paper will examine various materials used as wear media in the rehabilitation of pump parts for recycling, the use of other materials in manufactured design and appli- cations of these principles to other process Equipment.

Jan 1, 1978

A 36-year-old A-S-H pump, manufactured to designs dating back to 1936, was recently presented to the Gold Mine Museum by Envirotech. The pump, a B-frame three-piece rubber-lined Hydroseal unit, was supplied by Envirotech's predecessor company, Denver Machinery, and was installed by South Roodepoort Main Reef Areas Limited on 22nd March, 1948. Metals, materials, manufacturing The 37th Annual Conference of the Australasian Institute of Metals will be held in Ballarat (Australia) from 13th to 17th May, 1985. 1985is the Sesquicentennial year of Victoria, and for the first time the historic City of Ballarat has been chosen as the venue for an Australasian Institute of Metals congress. Steel rolling Conferences on steel rolling, sponsored by The Iron and Steel Institute of Japan (ISH), and supported by iron and steel institutes in many countries of the world, have been held since 1980. The first conference was held in Tokyo in 1980, sponsored by The Iron and Steel Institute of Japan.

Jan 1, 1984

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By Tom Watts

This paper will focus on the design, manufacture and use of pump safety systems on MMUs (Mobile Manufacturing Units – Bulk Trucks) with progressive cavity pumps. The practice of pumping bulk blasting agents is highly regulated and the explosives manufactures have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping.

Jan 1, 2009

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be care&lIy considered and investigated. This is the background behind a series of pump tests carried out by NTTRO NOBEL.

Jan 1, 1996

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be carefully considered and investigated. This is the background behind a series of pump tests carried out by NITRO NOBEL.

Jan 1, 1996

By M. Keevy, K. Hackney

Centrifugal slurry pump station and deposition sites are a common feature of many mines and mineral processing plants. Yanacocha Mine has completed the design of a pump station consisting of two trains of four pumps each. A number of trade-off studies was conducted to optimize the pump station design. The most significant of these was determining the drive types for the slurry pumps. The pump station duty can vary considerably due to the number of deposition points round the disposal site. The standard solution to this problem on a multi-stage pump train is to install one pump with a variable speed drive to control the pump station output by varying the speed of this pump and stopping and starting other stages. However, there are a number of negative impacts associated with this approach. These include head losses through pumps that are stationary or ?wind-milling?, different wear life on pumps that are running and pumps that are stationary, and slower response to the control system with the possibility of hunting. The use of variable speed drives on all the pumps was considered as an alternative to the standard solution. The factors considered in comparing these options were the control and operational differences, the pump efficiencies and absorbed power, the expected pump wear life, the impact on pump maintenance and the cost of the drive options. For this project the option of using all variable speed drives was selected. The paper presents the following aspects of the study: ?Description of the various options investigated. This includes a discussion on the required duty and the drive options. ?Technical comparison between the options. ?Description of the factors influencing pump performance and life.

Jan 1, 2007

[ ]

Jan 1, 1938

[ ]

Jan 1, 1938

By Scott G. Britton

Traditionally, water removal has taken a backseat to many other coal mining functions. However, it is a vital part of the total mine support system. In many US coal mines, more tons of water are removed each year than tons of coal. An excellent discussion of general drainage characteristics can be found in Chapter 8 of Elements of Practical Coal Mining, published by SME-AIME. This chapter is organized into three major sections. These are: designing effective drainage systems; constructing the main mine pumping station (static system); and constructing a portable pumping station (dynamic system). Each topic presents a separate discussion of the elements a construction foreman or engineer should consider for effective installation and operation of the mine drainage system. In addition, a list of pumping equipment manufacturers is available to interested persons and follows these sections.

Jan 1, 1983

By J. L. Osiensky, R. E. Williams, J. Linehan

The hydrostratigraphy of uranium in situ leach sites consists typically of interbedded layers of sand, silt, clay and gravel deposited by fluvial processes. 'These layers usually form leaky multiple aquifer systems where sand and gravel aquifers are separated by silt or clay confining layers (aquitards). It is very important to evaluate the hydraulic properties of the ore zone aquifer and the confining layers by aquifer pump testing to ascertain the effects that in situ leach mining will have on the multiple aquifer system. The degree to which current methods of aquifer pump testing will provide the information necessary to adequately characterize the hydraulic properties of the ore zone aquifer and its confining layers is dependent upon the hydrostratigraphic conditions at the site and the limitations of the testing methods. The primary objectives of the aquifer testing program should be to evaluate the vertical hydraulic conductivity of the confining layers and to quantify leakage into or out of the ore zone under mining conditions.

Jan 1, 1984

By T. M. Barczak, S. C. Tadolini

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of “topping off” the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

By T. M. Barczak

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of ?topping off? the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

Jan 1, 2008

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986