Search Documents

By Ethan Steward, Kyle Perry

The study investigates the effects of high-velocity impacts of common mine materials on a reinforced mine seal rated to 120 psi. It found that materials propelled during an underground explosion could generate enough stress to crack or damage seals, even with little visible damage. This highlights the need for careful evaluation of mine seals after any impact or high-pressure event.

Aug 1, 2023

By Kyle A. Perry, Ethan A. Steward

The mining of underground coal presents several hazards for miners, including the risk of an explosion fueled by methane gas and coal dust. Methane gas, produced during coal formation, can continuously leak into old workings and build up through its lower explosive limit. Underground coal mines are required to maintain safe conditions, either by ventilating old workings or sealing them off using approved methods. Seals must be designed to withstand instantaneous pressures for a minimum of four seconds. A design strength of at least 50 pounds per square inch (psi) is required for atmospheres monitored and maintained inert, 120 psi for non-inert or not monitored, and greater than 120 psi for special cases. Due to the high cost and testing environment availability, most mine seals are designed through calculations and computer modeling and not subjected to full-scale testing in a representative environment. High pressure is not the only threat that mine seals may be exposed to. During an underground explosion, pressure waves and gas expansion may propel common mine items and objects to a high velocity, generating enough energy to damage mine seals and reduce their strength. Damaged mine seals may fail to contain their rated pressure, allow high pressure gas and fumes to vent through the seal during an explosion, or allow gasses to leak through the seal later after an explosion has occurred. This paper examines the effects of high velocity impacts of common mine materials and items on a reinforced mine seal rated to 120 psi.

Jun 2, 2023

By E. Iasillo, R. R. Carneiro

Independent of the method chosen to forecast production, an accurate method to project metal extraction is needed in order to accommodate leach cycles that exceed leach data on hand and thus be able to accurately forecast production. Metal extraction data must be developed for each ore type identified in the deposit in order to apply the correct rate of leaching when a specific ore is being treated. Curve fitting is used to model the rate of disengagement of metal into the pregnant solution. This paper provides a description of a curve fitting algorithm developed by Mr. John T. Bartlett, inventor of the METSIM™ process simulation program. A methodology is provided by which the metallurgical data developed is evaluated to determine if accurate projections may be made from the data. A criteria has been developed to help determine when a column experiment may be terminated.

Jan 1, 2001

By R. W. Shoenberger, J. D. Clendenin, W. L. McMorris, N. Schapiro, B. R. Kuchta, A. A. Terchick, R. J. Gray, J. G. Price

INTRODUCTION * The United States is fortunate in having enormous reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by palynology,** stratigraphy, paleontology and petrography are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining (1) the economic justification for mining the coal, (2) the optimum design of the preparation plant and (3) the most effective use of the coal. Fortunately, the cost of mining coal has remained stable because of better mine planning, more efficient operations and increased mechanization of mining operations. However, increased mechanization raises the amount of impurities in the coal mined, and this requires more and better coal beneficiation to meet the more stringent quality requirements set by the market. Besides, mechanical miners also produce relatively fine coal and, to ensure maximum liberation of impurities, much of the coal presently being used must be crushed to a finer size prior to preparation. The bulk of all coals presently used in this country is mechanically cleaned, much of it at a lower specific gravity than in the past. This necessitates the use of new and improved processes and equipment for coal washing and recovery, such as heavy-medium cyclones and vessels, and froth flotation cells. However, because wet-cleaning processes are pre- dominant in the United States and fine coal retains large amounts of moisture, the increased production of cleaned fine coal accentuates the need for new or improved methods and equipment for dewatering and drying this coal. The larger amounts of coal being beneficiated and the use of new and improved beneficiation processes will aid in controlling and ultimately eliminating sources of pollution. Modem coal markets demand coals that meet rigid specifications. Most coals are purchased under contracts that specify moisture, ash, and sulfur contents, or heating value, depending upon the end use. There has also been a growing trend toward specifying other properties, including particle size and coking capability. These specifications may include not only the * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. ** Palynology is the study of plant microfossils, especially spores, pollen, and other types of fossils not usually studied by paleontologists.

Jan 1, 1968

By R. W. Shoenberger, J. E. McNulty, B. R. Kuchta, William Spackman, A. A. Terchick, M. E. Hopkins, Norman Schapiro, R. J. Gray, A. F. Duzy, M. P. Corriveau

INTRODUCTION * The United States is fortunate in having abundant reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most metallurgical-grade coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by petrography, paleontology, palynology, † physical stratigraphy, and geophysical methods are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining ( 1 ) the economic justification for mining the coal, (2) the optimum design of the preparation plant, and (3) the most effective use of the coal. Recent progress has been made in relating mineral matter, especially pyrite, in coal to geologic conditions and paleogeographic trends. l * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. † Palynology is the science concerned with plant microfossils, especially spores. pollen. and other fossils of microscopic size.

Jan 1, 1979

By R. R. Beebe

"Laboratory and pilot-scale tests are almost invariably required before metallurgical development can proceed. Difficulties with sampling, as well as with classical chemical and physical scaleups, are normally anticipated and relatively well-understood, but more subjective factors also come into play, including misunderstandings of the operating scheme chosen, wrong ""lessons"" learned from similar operations, failures to handle data appropriately, and even arbitrary intervention by management. The paper examines some of these subjective factors and suggests ways to guard against them. Several anecdotal case studies are used as examples, including when and where to heap leach or to mill specific types of gold ore.When the Romans first exploited the gold-rich gossans at Rio Tinto, they were guided by analyses and tests that delineated the ore deposits, identified the richer portions, and measured the gold recoveries achieved. There is little evidence, however, to suggest that test data were used to develop improved methods of metallurgical extraction. Indeed, it is likely that ores too difficult to treat were simply passed by, at least until improvements in full-scale operations could deal with them. For example, it is not difficult to imagine that an early metallurgist might test a tin ore by placing some in a fire; a smallscale emulation of the method actually used in practice."

Jan 1, 1997

Equity investments and loans are made in oil and gas and mining projects by the World Bank Group (WBG) as one piece of a multi-faceted quest to reduce poverty. The Bank mandate to reduce poverty through private sector investments has been contested by civil society organizations, so the Bank has established an independent review, entitled the Extractive Industries Review (EIR) www.eireview.org. The EIR is reviewing, from the perspective of affected stakeholders, the impacts and benefits of WBG development policy. In this paper, we review the indicators used by the WBG, academics and others to measure the effectiveness of investments. We argue that currently used frameworks and indicators do not capture local or regional data sets, and instead focus on available and easily aggregated information at the national level. A case review of the WBG?s International Finance Corporation (IFC) and Multilateral Insurance Guarantee Agency (MIGA) investments and loans in Sub-Saharan Africa provide material data buttressing the argument. Poverty studies in the extractive industries have a long way to go toward measuring and accounting for dollars spent and invested. The paper concludes with a call for project level and regional indicators to track poverty alleviation. Data gathered for this research was funded in part by the Extractive Industries Review.

Jan 1, 2003

By S. Viswanathan, Q. Han, A. S. Sabau

"In spite of recent advances in the mathematical modeling of fluid dynamics for materials processing applications, no significant advances have been made in the numerical discretization of these equations. In this work, the application of two-step projection methods for the numerical simulation of interdendritic flows is discussed. Unlike previous methods, the methods presented here are constructed for the exact equations which are characterized by variable density and volumetric fraction of the liquid. The drag terms, which describe the momentum loss due to the flow around and through the dendrite structures, are treated implicitly. Numerical examples for shrinkage-induced flow during solidification of an Al-4.5% Cu alloy bar is used to illustrate the effectiveness of the proposed algorithm.IntroductionLiquid contraction during solidification plays an important role in the formation of casting defects such as shrinkage voids, microporosity, and macrosegregation. Owing to their importance, the study of transport processes during solidification have received considerable attention during the past years [1, 2]. By the use of volume-averaging techniques, the mass and momentum equations for flow through a stationary dendritic structure were derived [3]. By using the volume-averaging techniques for multi-phase systems, two-phase transport equations for solidification problems were derived [4]."

Jan 1, 1999

By L B. Zhou, Q Wang

The present discussion focuses on the developmental directions of eco-restoration of acid mine waste rock dump, by using acid mine waste rock of Shuilong Mountain as an example. Based on the analysis of site factors, the current slope ecological restoration technologies of domestic and international and local practices have been integrated into the eco-restoration of acid mine waste rock in Shuilong Mountain. A set of suitable slope Eco-restoration technologies have been formulated locally for acid mine waste rock of Shuilong Mountain, which include establishing green barrier, implementing ecology buffer zones, selecting suitable plant species and combined seeding and tube-stock planting. It aims to restore the plant ecosystem to a near natural state, in couple with slope stabilisation and soil remediation.CITATION :Wang, Q and Zhou, L B, 2012. Projection of ecological restoration of acid mine waste rock of Shuilong Mountain at Dexing Copper Mine, in Proceedings Life-of-Mine 2012 , pp 305-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Francis Perron

The Directive 019 on mineral industry, which was officially adopted in 1989, is the main tool used by the Quebec Ministry of Environment for the environmental evaluation and control of mineral exploitation projects presented for approval. This document contain the environmental guidelines which must be met by all the mineral companies during and after exploitation. The Directive 019 also contain all the information required by the Quebec Ministry of Environment in order to fully analyse the environmental impacts caused by the mineral projects proposed to the Ministry for approval. The proposed modifications of the Directive 019 cover many new topics that were not addressed in prior editions, these include : water recirculation, groundwater protection, tailings management and post exploitation environmental controls.

Nov 1, 2002

? Introduction ? Partenariat MRNF - MAE ? Goldex ? Manitou : - Ré-aménagement du bassin versant - Accès aux zones problématiques - Filtration du ruisseau pour les travaux - Nettoyage près de la rivière - Régulation du débit et bassin - Digues et bassins - Déposition résidus Goldex ? Chemins d?accès Goldex-Manitou ? Pipelines: Goldex ? Retour Goldex ? Manitou ? Station de pompage ? Résumé

Feb 1, 2008

By René Dufour

Jusqu?à son acquisition par MM René Dufour et Alain Robin en 1994, les claims miniers et les droits de surface de la propriété étaient détenus depuis 1953 par la société Québec Columbium, une filiale de la socité américaine Kennecott Copper qui y a réalisé d?importants travaux miniers. En 1995 la compagnie NIOCAN inc. fut incorporée; ses actions furent inscrites à la bourse de Montréal en 1997, et à la bourse de Toronto en décembre 1999. Jusqu?à maintenant, NIOCAN a investi plus de 7 millions de dollars dans le développement de sa propriété minière de niobium située à quelques 40 kilomètres au nord-ouest de Montréal. Le haut rendement économique des deux gisements principaux que compte exploiter la compagnie, le S-60 et le HWM-2, a été établie par des études de faisabilité effectuées par le consortium Met-Chem/SNC-Lavalin. La mission que s?est donnée NIOCAN inc. consiste à mettre en production ses deux gisements et à devenir ainsi productrice de ferroniobium dans les plus brefs délais. Figure 2 Le projet est présentement à un stade avancé d?obtention du certificat d?autorisation du ministère de l?Environnement. À plus long terme, la compagnie compte aussi exploiter les sous-produits de ses gisements (apatite, forsterite, magnétite, calcaire et terres rares).

May 1, 2003

By Robson Jacinto Coelho

A equipe da Coqueria identificou a possibilidade de reduzir o Burn Loss, que é a perda de material por queima durante o processo de coqueificação. Após uma série de estudos, utilizando a metodologia Seis Sigma, identificou-se oportunidades de melhorias operacionais que trariam mais eficiência, estabilidade operacional e consequente aumento na produção de coque e vapor, tais como: maior controle na admissão de ar, controle das perdas de coque e carvão, vedação dos fornos de coque e execução de paradas programadas específicas para Preservação Refratária, com foco na redução do back log e consequente prolongamento da vida útil das baterias de fornos de coque. A redução Burn Loss aumenta o rendimento coque/ carvão, com consequente redução do consumo específico de carvão e aumento na produção de coque e vapor. A implantação desse projeto permitiu a redução de 2,5 dólares por tonelada de aço produzida no Fiscal Year 16/17.

Oct 30, 2017

By Filipe Sathler

O projeto CR298 se iniciou no final do segundo semestre de 2014 quando o Coque Rate (CR) médio era de 351,0 kg/t. A meta definida foi de atingir média mensal de CR de 298 kg/t em dezembro de 2016, permitindo aumento de produção com alta taxa de injeção de carvão PCI, porém, com baixo Fuel Rate, garantindo competitividade de mercado. Sendo assim, foi desenvolvido e divulgado um novo modelo mental de operação, processo, manutenção e gestão, envolvendo toda a área de Redução, Utilidades e Aciaria. Várias premissas técnicas foram estabelecidas com um plano de ação detalhado para garantir estabilidade no processo dos altos fornos de forma a obter este resultado. A meta foi atingida antes mesmo do planejado: CR 291,3 kg/t em Maio de 2016 e em 2016 a média anual foi de 297,0 kg/t, com Fuel Rate de 484,4 kg/t.

Oct 30, 2017

By Jael Moutinho dos Santos

Em função do elevado consumo de corpos moedores de alto Cromo e do alto custo de sua fabricação com matéria prima nobre, busca-se o desenvolvimento de novas ligas de corpos moedores na busca de um melhor custo benefício. Devido ao efeito sinérgico do perfil de desgaste envolvendo fenômenos corrosivos e abrasivos em bolas de moinho, o desenvolvimento de novas ligas de ferro fundido branco alto cromo tem sido uma alternativa para suportar o desgaste precoce provocado por tais fenômenos. As amostras de corpos moedores, analisados mediante ensaio de análise química, dureza, análise micrográfica e seguidos de ensaios de moagem (úmido e seco), servirão a um desempenho comparativo para se designar a melhor liga a ser aplicada nos processos de moagem secundária de minério de ferro a úmido.

Oct 30, 2017

By Wesley Alves Quintão

O projeto criado e aqui apresentado teve por objetivo atender as necessidades da empresa em relação às metas de economia de energia e adequação ao mercado atual e para isso foi estudada uma maneira de gerar economia de gás com o desligamento de pilotos de ignição e também eliminar atrasos mecânicos no processo de acendimento, purga e estanqueidade do forno de reaquecimento Stein, através do uso de recursos da automação, eliminando dispositivos eletromecânicos garantindo velocidade de informação, economia comprovada de gás e maior confiabilidade no sistema de monitoramento do processo.

Aug 17, 2017

By André Pereira Barbosa

Este projeto tem como objetivo desenvolver o uso do transporte multimodal nas operações de entrega de produtos via cabotagem, para as regiões Norte e Nordeste, em sinergia de todas as usinas da ArcelorMittal no Brasil. O trabalho visa demonstrar os principais dificuldades e benefícios da utilização da cabotagem. O projeto foi subdividido em etapas de implantação, que se iniciou com um processo de contratação, envolvendo os fornecedores de cabotagem e serviços de ovação para as operações das unidades de Longos (Cariacica, Sabará, Itaúna, Juiz de Fora e Piracicaba) e de Planos (Tubarão) de forma conjunta buscando uma melhor condição comercial e contratos sólidos de atendimento, com foco na utilização das mesmas estruturas de terminais, portos, fornecedores e até containers. Foi estimada uma redução significante dos impactos socioambientais e dos custos de fretes para organização.

Aug 17, 2017

By Henrique de Araújo Resende

Em função do aumento constante da produtividade nos laminadores e linhas de processo de usinas siderúrgicas e de alumínio, está cada vez mais evidente a necessidade de aumentar as campanhas de produção dos mandris de bobinadeiras e desbobinadeiras, reduzir as paradas de manutenção das linhas além de minimizar ao máximo os custos com reparo e fabricação. Para isso, é importante conhecer os diversos projetos de mandris utilizados nos últimos anos, os maquinários envolvidos na fabricação e reparo desses equipamentos além de estar atualizado quanto às novas tecnologias que poderão ser aplicadas. Para possibilitar o entendimento descrito acima, este material será divido em 3 partes: Projetos SMS de mandris no Brasil; Condições de fabricação e reparo; Novas tecnologias. A SMS possui 58 mandris em operação hoje no Brasil estratificados entre os seus principais clientes, desde linhas de decapagem e laminação a quente até a saída do produto final após os laminadores a frio na galvanização e linhas de pintura e corte. Com isso, é possível estabelecer uma análise técnica do desempenho de cada equipamento e sobressalente de forma bem estruturada. Esse é o principal objetivo desse trabalho.

Aug 16, 2017

By José Geraldo da Silveira, Luiz José Gonçalves, André Mendes Carneiro Lyrio, Raylander Rocha Pessoa, Péricles Guimarães Oliveira Aguiar, Guilherme Ribeiro do Espírito Santo, Filipe Soares Pontes

Este trabalho tem como objetivo apresentar a origem do projeto inovador do cadinho do Alto-forno 2 além do planejamento, a implantação e os resultados obtidos no Alto-forno 2 da Aperam South America após a reforma. O trabalho de pesquisa e desenvolvimento teve início em 2012 após a primeira marcha fria com conseqüente redução das temperaturas da soleira. Foram realizadas diversas reuniões, discussões e seminário sobre alto-forno com especialistas de diversas empresas. A mudança de redutor carvão vegetal para coque por seis meses serviu para comprovar parte da teoria construída pelo time da redução. Para, por fim, culminar no conceito por trás do problema do AF2 e então o novo design do cadinho que foi proposto e implantado na reforma iniciada em dezembro de 2017. Após sua implantação, conforme teorizado pelo time, uma nova gama de resultados e patamar de operação foram atingidos, comprovando diversas das teorias formuladas.

Oct 1, 2019

By Eustaquio Vieira Junior

O Alto-Forno 2 da thyssenkrupp CSA, no Rio de Janeiro, iniciou sua primeira campanha em 16 de dezembro de 2010. No decorrer de sua campanha, verificou-se problemas de deslocamento de staves de ferro fundido, deformação dos staves de cobre e desgaste acentuado do refratário do top cone. Na análise dos eventos adotou-se a inspeção por vídeo endoscopia e em seguida foram tomadas algumas ações para recuperação e preservação do Alto-Forno 2, sendo estendidas também do Alto-Forno 1. Dentre as ações de preservação dos Altos-Fornos destaca-se a projeção robotizada de material refratário, shotcrete, visando reduzir o desgaste acentuado dos staves e deterioração de suas tubulações de refrigeração. O trabalho apresenta o detalhamento das técnicas utilizadas e seleção de materiais assim como os preparativos operacionais que garantiram o bom desempenho do Alto-Forno 2 nos momentos que antecederam a parada e após seu retorno à operação, mostrando que a atividade é viável do ponto de vista técnico e financeiro.

Oct 30, 2017