Search Documents

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

By Vladyslav M. Sokolov

The cost effective and environmentally friendly recycling technology was developed and tested. It enables utilization of the fine nickel-base superalloy scrap in a form of heavily oxidized scarfing granulates. The process of granulates generation was discussed in details. Their properties were investigated. The results of literature search showed anticipated sufficient improvement of the properties of cast iron by its alloying with the elements from the scarfing granulates. The novel alloying approach is based on the two stage reduction operation. Firstly thegranulates were partially reduced in a solid state by their exposure with powdery carbon at the range of 1550 ? 1700°C. Then the gotten product was efficiently introduced into liquid iron since it has a form of fine natural agglomerates for arranging the optimal conditions for reduction of the granulates. The thermodynamic evaluation demonstrates higher reduction efficiency of carbon and silicon dissolved in iron than of the same elements in a form of the separate phases. The considered process partially provides itself by energy since the reaction of reduction of the chromium oxide by silicon dissolved in liquid iron has exothermal character. The mostly complete extraction of Ni was received. The sufficient reclamation of Cr was gotten at the same time.

Jan 1, 2006

By J. L. Holman

In conjunction with its research program on separation, recovery, and recycling of metal, mineral, and energy-based materials in urban refuse, the U.S. Bureau of Mines is developing means to reuse and recycle plastics discarded in raw municipal waste. Experimental work on plastic waste from a community collection has produced some guidelines for systematic methods of processing, including air classification, cleaning, separation, and use or disposal. Sink-float methods are a practical means of separation into types. Methods for final disposition of the plastic waste include refabrication, thermal decomposition, and incineration.

Jan 1, 1972

By Z. F. Dai

The Thompson Nickel Belt, located in Northern Manitoba, Canada, contains more than 400 million tonnes of ultramafic low-grade nickel mineralization in 9 deposits. One of these, the Pipe deposit, was mined between 1971 and 1983 producing a Ni concentrate of 9% to 11% grade at 73% recovery. The operation was terminated because the poor recovery, low Ni grade and high MgO con-tent of the concentrate made processing this ore uneconomical at the metal prices prevailing at that time. Vale Inco is now re-evaluating these deposits with the intent of providing a new source of concentrate for its Thompson integrated processing facility. It is known that serpentine slimes coating on the sulphide surfaces are responsible for the poor metallurgy. Various desliming methods were tested including settling, elutriating, tabling and hydrocycloning. Hydrocycloning has proven to be the most effective means of desliming. With a feed assaying 0.70% Ni and 33% MgO, a rougher flotation concentrate assaying 22.7% Ni and 4.8% MgO was produced at a Ni recovery of 62.5% (relative to the feed to grinding), with no utilization of slimes dispersants. Another 16.6% Ni recovery was achieved in scavenger flotation resulting in a total Ni recovery of 79.1%. Batch flotation tests using various flowsheet configurations to optimize the grinding, desliming, reagentizing and flotation conditions are in progress.

Jan 1, 2014

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for over three years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1996

By Patrick P. M. Afenya

"The paper point out the mineralogical aspects about metals processing volcano-related gold, silver and copper ores. The copper group of metals comprises gold, cooper and silver. These metals have been considered together here because of similarities in their chemical properties. Consequently, these metals commonly form minerals with the same elements or group of elements. It is realized that the formation of minerals and final physicaland chemical states of any mineral may depend on many factors such as temperature, pressure, activity of species and pH of the fluid, mode of formation, paragenesis, geological age and post crystallization events. For the purpose of this discussion, attention will be focused on temperature as the principal factor influencing mineral formation."

Jul 31, 2003

By C. Richard Tinsley

As discussed in the economics section of this article, the main processing consideration is whether manganese will be recovered, as this has major implications for reagent consumption. Nodule processing can be classified into three sections; smelting, roasting, and leaching. Many patents have been issued for various stages of these techniques. Since extensive laboratory and pilot plant testing is continuing, it is certain that some companies are close to full-scale commercial processes. Published data does not include all of the possible concepts for nodule treatment. In fact, one may suspect that published flowsheets are those that have been rejected or have since been extensively modified.

Jan 4, 1975

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

Declining metal prices over the last few years have reduced the number of new metallurgical plants being built and limited opportunities for introducing new processes. However, technological advances are still being made. With increasing economic pressures, the emphasis is now on reducing unit costs by making equipment larger and through use of technologies with lower operating costs. This trend can be seen in the increasing size of grinding mills and flotation cells used in recent plant designs and in the adoption of HPGR crushing as an alternative to SAG milling. Few new technologies achieve widespread introduction until there are clear economic or operational drivers. These might currently include: ò          increasingly stringent environmental standards; ò          availability of exotic materials for equipment construction; ò          increasingly sophisticated instrumentation and control systems; ò          the need to treat increasingly refractory oretypes; and ò          the length of supply routes to many new plants. As a result of these drivers, a number of new and revitalised technologies will get increasing prominence in the design of new operations, such as: ò          use of ultrafine milling equipment such as MIM's Isamill for treatment of refractory gold ore concentrates; ò          use of thiourea as an alternative for cyanide in sensitive locations; ò          novel hydrometallurgical routes for treating base metal ores in remote locations; ò          paste thickening for tailings deposition; and intensive cyanidation of gravity concentrate

Jan 1, 2000

By Eduardo de Oliveira Cabral

O trabalho apresenta uma comparação entre os principais tipos de processo de aglomeração mecânica de pós e lamas, com foco nas tecnologias de tambor e prato rotativo, misturador horizontal e misturador intensivo vertical, destacando as vantagens e desvantagens de cada processo de acordo com o objetivo final.

Oct 30, 2017

By Bruna Silva de Almeida

Este trabalho apresenta o desenvolvimento do tratamento térmico de austêmpera em escala industrial do aço microligado ao Boro 22MnB5 da Companhia Siderúrgica Nacional – CSN, fornecido em bobina para o cliente Panatlântica para beneficiamento e posteriormente austemperado e testado em seu cliente Metal Mecânica Itália – MMI. Assim, descreve-se as etapas do processo de fabricação e caracterização do comportamento do material na aplicação em tiras austemperadas de aço na confecção de lâminas rotativas, que é um item importante na indústria de transformação de papel ondulado. O diferencial está na versatilidade desse aço, pois, apresenta boas propriedades de tenacidade, alta faixa de dureza e resistência ao desgaste, aliada a boa estampabilidade. Tal sucesso se deve a microestrutura bainítica e sua excelente ductilidade capaz de suportar as operações de estampagem após tratamento térmico.

Oct 30, 2017

By Robson Leandro Silva

O processo de descarburação de aço inoxidável contendo alto teor de carbono inicial via processo VOD foi estudado utilizando o aço AISI 304. Devido a questões operacionais, o carbono inicial aplicado no processo VOD da Villares Metals é próximo a 1% e a pressão de trabalho de 600mbar. O objetivo do trabalho foi encontrar o instante em que se torna possível a redução da pressão do sistema de acordo com o carbono inicial do processo. Para isso foram realizados testes em corridas industriais de 25 t interrompendo o sopro de oxigênio e realizando análise química em diferentes tempos de sopro. O resultado dos testes mostrou que após 11min de sopro de oxigênio é possível reduzir a pressão do sistema levando em consideração as limitações operacionais, podendo assim reduzir a oxidação de elementos de liga durante essa etapa.

Oct 30, 2017

By João Carmo Vendramim

A oxidação da superfície de peças, ferramentas, moldes ou matrizes construídas em ligas ferrosas tem larga utilização na indústria. As aplicações podem ser as mais diversas, tais como simplesmente atender às questões estéticas, proteção da superfície contra a corrosão, ou proteção contra a interação química com outros metais. Dentre as técnicas industriais utilizadas há o processo conhecido como “Oxidação Negra” que é realizado em baixas temperaturas, com imersão do aço da peça em óleo quente, ou banho de sal especial, ou mesmo a frio (soluções especiais). Outros processos utilizam fornos industriais com atmosfera de ar para aquecer a liga ferrosa até temperaturas da ordem de 500ºC e acrescentar (“pingar”) água como fonte de oxigênio. E em outros, aplicação ceras hidrocarbonetadas e ácidos inorgânicos e posterior oxidação [1] com aquecimento a temperaturas da ordem de 500ºC. Nesses processos, o objetivo é formar uma camada de óxidos tipos Magnetita e Hematita cujas características de menor coeficiente de atrito e determinadas propriedades físicas e químicas serviriam de barreira à interação química com outros metais em contato. A camada de óxido obtida nas condições descritas acima é bastante útil para determinadas aplicações industriais, tais como moldes de injeção de alumínio. Esse texto descreve o processo de oxidação desenvolvido utilizando a tecnologia de plasma.

Jul 30, 2018

By Edmilson Renato de Castro

Apresentam-se o processo e o protótipo de forno para a produção de ferro gusa por redução carbotérmica estimulada por micro-ondas de minério de ferro, na forma de pelotas auto-redutoras. O forno de redução com potência regulável de até 15 kW de micro-ondas de 2.45 GHz foi especialmente projetado e construído para este processo. A estrutura do forno é em aço inoxidável e utiliza três geradores de micro-ondas focados para o centro de um aplicador cilíndrico. Com esta configuração conseguiu-se produzir um campo eletromagnético de alta densidade energética. A carga de pelotas auto-redutoras, com massa em torno de 20 g foi reduzida em um cadinho de carbeto de silício. A montagem do forno dispõe de uma balança elétrica adaptada para suportar o cadinho de redução. O presente forno dispõe de controle e medida da potência fornecida e refletida, permitindo medir a energia de micro-ondas efetivamente aplicada à carga. Esta característica permitiu realizar balanços de massa e de energia além de determinar a evolução da taxa de reação através da medida contínua da massa das pelotas sob redução, ao longo do tempo de processamento. Obtiveram-se curvas cinéticas de redução carbotérmica de minério de ferro incentivada por micro-ondas e de seu consumo de energia durante o processo.

Aug 1, 2018

By K. J. Fair, G. Van Weert, J. E. Schneider

"IntroductionCyanidation is the principal process for extracting gold from ores . Many primary gold ores, however, are partially or totally refractory in the conventional cyanidation process.Considerable success has been achieved with new gold leaching techniques, such as intensive cyanidation, pressure cyanidation, carbon-in-leach cyanidation, etc. These techniques however, do not offer substantial gains in gold extraction from refractory pyrites.The more drastic pretreatment processes such as roasting, chemical oxidation, autoclave oxidation, and bacterial oxidation all utilize oxidation to break down the structures of pyrite and arsenopyrite. This generally renders the gold amenable to cyanidation.Comparative cost studies indicate that the oldest commercial pretreatment method, i.e. high temperature roasting, is currently the least expensive option if the sulphuric acid can be sold. It operates with air at atmospheric pressure and is characterized by fast reaction rates. For an alternative hydrometallurgical con centrate treatment method to be competitive, it too should operate with air at atmospheric pressure and with fast reaction rates. The NITROX process meets these conditions."

Jan 1, 1986

By William W. Edgerton, Moussa Wone, David H. Corkum, Carlton M. Ray

"The DC Clean Rivers (DCCR) Project is a 25 year, $2.6 Billion court ordered project to reduce combined sewer overflows (CSOs) discharging into the Potomac and Anacostia Rivers and Rock Creek, and also reduce flooding in the northern areas of the District of Columbia. Like all massive infrastructure programs, DCCR faced technical challenges, management challenges, risks of cost and schedule overruns, procurement challenges, and financing challenges. While DC Water is no stranger to large capital improvement projects (CIP), this CSO Program represents a once in a lifetime event for the Owner requiring the assembly of a single purpose team to implement. Some of the DCCR Project team’s most successful accomplishments to date are attributable to its introduction of early contractor involvement (ECI) to thoroughly vet the work from the perspective of the future constructors, development of functional baselines to share risks that are difficult to price and reduce reliance on geotechnical baseline interpretation during tunnel excavation, and attainment of financing through Municipal Century Green Bonds based on using design criteria of a minimum of 100 year life for the structures to establish intergenerational equity and fairness. This paper will discuss these innovations in detail and provide some sets of recommendations for the underground industry on when and how to use different approaches to better manage projects of this magnitude. INTRODUCTION The District of Columbia Water and Sewer Authority (DC Water) is an independent multi-jurisdictional authority that was established in 1996. Its primary mission is to provide water distribution services to more than 640,000 residents in the District of Columbia (District), and sewer treatment and disposal to 1.6 million residents of the District, Montgomery and Prince George’s counties in Maryland and Fairfax and Loudoun counties in Virginia."

Jan 1, 2016

By G M. Taylor

The application of high technology to monitor and control fire life safety, critical functionality in tunnels and underground spaces generally has progressed at an ever accelerating rate over the past decade. Today these systems comprise some of the most complex and little understood aspects of the tunnel/underground facility construction industry, with this area being perceived as high risk comprising impenetrably complex ‘black box’ technology covered in blinking LEDs. This paper will seek to explode some urban myths and common misconceptions associated with such systems, providing its intended audience with a review of what all this technology comprises and where the real risks lie in its delivery lie.The author contends (and looks to support such contention via this paper) that by applying baseline project and risk management processes to the procurement of this widely misunderstood black box technology, the quality of the final outcome can be much improved, driving innovation, reducing both cost and significantly mitigating delivery risk.CITATION:Taylor, G M, 2014. Procuring control and intelligent traffic systems for major new build projects – avoiding pitfalls and maximising value, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Alan Foley

The Portable Remote Operated Drill was developed in Sydney, Australia in the 1990’s. The device is a platform for many in-situ seabed sampling and coring tasks. The range of tools developed for use in PROD’s magazine now includes gas detectors, vane testers, penetrometers and corers. This paper presents aspects of the soils testing undertaken in deepwater since 2005, focusing on testing of methane hydrates and reefal accumulations. The varied selection of tools carried in PROD’s magazines allow the unit to perform several functions from the seafloor in one deployment.

Sep 24, 2006

By Alfredo Ramos Castro

La Cerro de Pasco Corporation se encarga de la producción de minerales como el cobre, plomo, zinc, plata, bismuto y algunos subproductos entre los que está en el cadmio, selenio y telurio. Entorno a esta panorama, surge la creación de la planta de cadmio que busca obtener dicho producto refinado en los precipitadores Cottrell y el residuo de purificación de la Planta de zinc, a partir de las materias primas el polvo de los hornos de plomo recuperado. En este sentido, el texto describe los procesos de producción de cadmio refinado que van desde la obtención de la materia prima hasta el moldeo del cadmio refinado para la venta.

Aug 20, 1963

By Marco Ojeda, Caio Moreira, Edelink Tinoco

Este documento técnico analiza la viabilidad del uso de un relave minero de la empresa Nexa Resources, cómo componente principal para la producción de cemento. El proyecto contempla dos etapas, en la primera etapa se acondicionan las proporciones de los componentes del relave mediante la flotación para en una segunda etapa hacer el tratamiento térmico del relave acondicionado y así producir el Clinker, que es la materia prima base que se usa para fabricar el cemento.

Sep 29, 2023