Search Documents

By W. Rostoker

Packing Experiments The porosity and most of the other physical properties of a coherent mass of any material built up by the packing together of discrete particles will obviously vary with, and be governed by, the manner of association of the particles. The relation of packing to powder metallurgy has been discussed in some detail by at least two authors. Packing Theory Theories of particle packing have been put forward by C. C. Furnas and A. E. R. Westman. Although their approach to the problem is not the same, their conclusions are similar. In the process of packing, they visualize the voids of a uniformly sized material becoming filled with particles of a smaller size, and the voids between these being filled in turn with still finer particles. Obviously, if this process is carried ad infinitum, the resultant mass will have the same density as the constituent particles. In practice, of course, such a density of packing is never attained. In addition, the premise is made that successive particle sizes must fit into the voids left by the immediately larger particles- an assumption requiring definite size gradations and also particle shapes. It remained, then, for theory to correlate relative diameter ratios, and proportions and numbers of sizes of particles, for requisite packed densities. Briefly, the following principles were postulated: (a) For an infinite diameter ratio between largest and smallest sizes, an infinite number of particle sizes in proper proportion is required to give natural density. (b) For a given diameter ratio, there is a maximum number of permissible particle sizes for maximum packed density (Furnas). (c) Provided the particle shape is spherical, or approximately so, the proportions o particle sizes can be calculated. (d) The ratios of successive diameters of particles are in geometric progression.

Jan 1, 1947

By Claus G. Goetzel

PRESSING of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal [ ] friction. As long as curved surfaces, recesses, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more difficult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB). Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. VARIABLE FACTORS IN MOLDING POWDERED METAL PARTS Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2 : I would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only I.5, a compression ratio of 5:I would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1945

Pressing-Drill Method - A Representative Method for Taking Analysis Samples from Recycled Materials

Sep 13, 2010

Until recently, nickel laterite projects have been largely ignored, due to their supposedly higher treatment costs compared with sulphides, and to their perceived processing difficulties. A number of laterite projects in the 1970s were abandoned because of high capital and operating costs, while others experienced severe technical difficulties. Conventional wisdom had it that laterites would not be exploited until most of the sulphide orebodies had been depleted. Why then, have Australian mining and exploration companies started a resurgence of interest in the treatment of nickel laterites? It all began with the Bulong project, which has been under study since 1987, while more recently two further projects, Murrin Murrin and Cawse, have been initiated and are being fast-tracked to take advantage of the current high nickel and cobalt prices. A further project in NSW, Syerston, has also been investigated at bench-scale, but no further development has yet been announced. All these projects have the following advantages: 1. Good location near a major mining centre and,reasonably close to power, water, roads, accommodation and a developed service industry. 2. Straightforward, low cost mining. 3. Low cost of acid or sulphur. 4. Good to very good cobalt credits. In addition, there have been significant technological developments in the design and operation of high pressure autoclaves and high rate thickeners, as well as solvent extraction and electrowinning technology. This has helped to decrease capital costs and technical risks, and has allowed the development of alternative flowsheets to the existing laterite operations (Taylor, 1996).

Jan 1, 1996

By W. Curlook, V. G. Papangelakis, M. Baghalha

A pressure acid leaching process has been developed for the extraction of metal values, nickel, copper, cobalt and zinc, from base metal smelter slags. The basic concept contemplates cooling the smelter slags through solidification sufficiently slowly to induce a good measure of crystallization; and subsequently, after fine grinding, to pressure leach such slags at around 250°C while applying oxygen overpressure, utilizing smelter byproduct sulphuric acid. High levels of extraction of the slags' metal values are thereby achieved. It has been shown that if the same slags are quenched thereby producing an amorphous structure, the resulting metal extractions are very low. The process is applicable to smelting furnace throwaway/discard/dump slags, as well as to in-process converter slags. By extracting the bulk of the residual base metal values in the throwaway/discard/dump slags, the resulting leached residues are rendered virtually benign vis-à-vis the external environment.

Jan 1, 2004

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification such as nickel (Ni), cobalt (Co), copper (Cu) and manganese (Mn) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte; ammoniacal leaching (gas reduction or Cuprion); and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered the pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stem from the 1970s and 1980s, and are not always easily accessible. This article details the series of tests conducted and provides updated results obtained — high Ni/Co/Cu recovery with limited manganese/iron (Mn/Fe) — as well as comments on the potential treatment options on the product solution and residue.

Sep 1, 2025

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification (nickel, cobalt, copper, and manganese) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte, ammoniacal leaching (gas reduction or Cuprion), and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stems from the 1970s and 1980s and is not always easily accessible. This paper will detail the series of tests conducted and provide updated results obtained (high Ni/Co/Cu recovery with limited Mn/Fe), as well as comment on the potential treatment options on the product solution and residue.

Feb 1, 2025

By M. J. Collins

Pressure leaching of zinc sulphide concentrates has been practiced commercially for nearly two decades. The process, which includes direct leaching of concentrate with spent electrolyte in an autoclave, has been commercialized at four separate locations to date. In pilot studies carried out in the Dynatec lab in Fort Saskatchewan, dozens of additional zinc concentrates have been shown to be amenable to pressure leaching. This paper highlights recent improvements in zinc pressure leaching that have been identified through process development studies, and how the experience gained in these studies has been utilized in the development of a new copper pressure leach process.

Jan 1, 2000

By Wolfgang Pietsch

Pressure agglomeration using tableting machines, roll presses, punch presses, isostatic pressing equipment, extrusion presses, and other less common equipment, represents a large share among commercial applications of size enlargement by agglomeration. The paper attempts to classify and describe the equipment and technology, their development and state of the art, as well as their respective applications, advantages, and disadvantages.

Jan 1, 1977

By Lloyd M. English

Accurate knowledge of the gas content of coal seams has always been important, according to the work of W. P. Diamond and J. R. Levine, 1981, but is becoming increasingly important for several reasons: Excessive gas emissions in the mine can create explosion hazards. Depletion of shallower coal reserves is forcing underground operations to greater depths where coal gas content is often greater. Natural gas prices and the need for new energy sources make naturally occurring coal gas a potential resource of economic interest. Information on coal gas content will impact mine designs, mine ventilation system specifications, and the effectiveness of methane control procedures used. Accurate resource assessment is needed for projecting and designing potential gas utilization enterprises. The emphasis upon methane hazards in mining operations, and upon potential methane utilization, has led us to improve upon the procedures used to determine coalbed methane levels.

Jan 1, 1984

By R. Lee Wooten, Marco D. Boscardin, James M. Taylor

An earth pressure balance (EPB) tunnel boring machine (TBM) and pipe jacking were used to construct a 430-meter-long segment of sanitary sewer force main. The force main was constructed by first jacking a 2045-mm-outside-diameter, reinforced concrete cylinder pipe (RCCP) casing through alluvial sands and gravels. Later, a 1220-mm-diameter, ductile iron carrier pipe was installed within the casing pipe. The main concern affecting the construction method selection was the elimination of the need for dewatering, which could cause groundwater flow from deeper, contaminated sands up across a silt aquitard into cleaner, shallower sands. In addition, the method selected reduced the volume of soil to be handled and, consequentially, the potential amount of contaminated soil to be managed. Items discussed in the paper include provisions for handling boulders and controlling ground movements as excavation and jacking occurred approximately 300 mm beneath an active,4800 kPa, 254-mm-diameter natural gas transmission pipeline.

Jan 1, 1997

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Karoly (Charles) Kocsis, Jeff Johnson, Felipe Calizaya, Tulio Dias, Natanna Nunes

Two pressure balancing chambers were constructed at a Colorado coal mine to reduce the risk of spontaneous combustion. Each chamber was established by installing a Kennedy stopping at about 10 ft (3 m) in front of an isolation seal, and equipped with two safety doors, a nitrogen injection system, and a set of environmental monitors. Several pressure balancing tests for different ventilation conditions were conducted in these chambers. During each test, pressurized nitrogen was injected into the chamber and the pressure differentials across the stoppings and seals monitored. This study presents a summary of the results achieved, lessons learned, and the basic requirements to operate a pressure chamber effectively.

Feb 1, 2024

By R. R. Brandenthaler

CONTROLLING -the pressure under which a well produces crude oil has advantages that are ap¬parently not entirely realized by many operators in the Mid-Continent district. The possibilities of utilizing well pressures are indicated by a series of ex-periments recently completed by the Bureau of Mines in which pressure control was successfully applied to 20 wells in, the Davenport field. The flowing period of all of .the wells was lengthened in some instances it was. more than doubled. The daily oil production from approximately one-half of the tested wells was in-creased. The amount of gas produced per barrel of oil was decreased, and this, in addition to a slower rate of decline in production, indicated that the ultimate re-covery had been increased. The successful application of pressure control to flow-ing oil wells must take into consideration the relation-ships existing between pressures in the different parts of the system which, though not equal, are nevertheless more or less interrelated. These relationships, which have such an important bearing on the results obtained by applying pressure control, are as follows: A change in rock pressure will affect the tubing pressure, casing pressure, and differential pressure, but it will not affect the trap pressure. A change in tubing pressure will affect the differential pressure and casing pressure; also, a change in casing pressure will affect the tubing pressure and differential pressure. Trap pressures are not affected by rock pressure, casing pressure, tubing pressure, or differential pressure, unless the traps are required to handle gas and oil beyond their capacity. Trap pressures will affect the differential pressure, tubing pressure, and casing pressure and any changes at the well-head, whether differential pressure, tubing pres-sure or casing pressure, will affect the pressures in the well. Any change in rock pressure results in a change in the tubing pressure, casing pressure, and differential pressure. When any sudden or unusual change in well-head pres-sures occurs (for example, an erratic tubing pressure), and when a sudden decrease in oil or gas takes place, it is al-ways advisable to note whether the trap pressure has changed. If the trap pressure has not changed, note whether the oil line from the trap to the flow-tank has become clogged, as would be evidenced by a rise in the oil level in, the trap. If the oil line is functioning properly, and if the trap pressure has not changed, the flow-line from the well to the trap should be inspected. If it is free from obstructions, then changes in the differential pressure, tubing pressure, and casing pressure must be due to changed well conditions.

Jan 4, 1927

By Rowe P, Rogers D, Warren M

Pressure cyanidation of the minus 10 micron slimes fraction of the Fimiston flotation concentrates for the recovery of gold values has been evaluated as an alternative processing route to the roasting and atmospheric cyanide leaching of the calcine. Laboratory and pilot trials have demonstrated that gold extractions of greater than 94 per cent can be achieved at cyanide consumptions of 12-24 kg/t and oxygen consumptions of 0.1-0.3 Nm3/t with total pressures of 1000-2000 kPa. Economic and operational assessment of several reactor configurations suggests autoclaves may be preferred over pipe reactors at treatment rates of 10 t concentrate/h.

Jan 1, 1996

By Shulin Nie

The detonability of a chemically gassed emulsion explosive has been studied in recent tests, after the study of three micro-balloon sensitized emulsion explosives. Blasting experiments in steel pipes and computer simulation have been carried out. This study showed that the gassed emulsion explosive and the micro-balloon sensitized emulsion explosives have different desensitization features. Namely, the gassed emulsion explosive can recover its detonability very rapidly after the pressure vanishes, in contrary to the micro-balloon sensitized explosives.

Jan 1, 1997

To more rapidly and economically prepare solutions for chemical analysis, of a wide range of ores, slags, minerals, and metals. Approach A Simple pressure-dissolution system was devised using an inexpensive, heavy wall plastic bottle containing a sample in an acid medium. Using the technique, a complex silicate sample can be dissolved in less than 1 hour. How It Works A weighed portion of a sample, ground to minus 100-mesh, is placed into a polycarbonate or polysulfone plastic bottle. A mixture of hydrochloric acid, nitric acid, and hydrofluoric acid then is added. The bottle threads are wrapped with a layer of Teflon tape to prevent leakage, and the bottle cap is screwed on tightly. The sealed bottle is placed in a balling water bath. In the hot water, the plastic bottle acts as a pressure vessel to contain the pressure generated inside it. This technique should only be used by trained experienced people who are familiar with the hazards of hot acids under pressure. After being cooled in cold water, the resulting solution is brought to the final volume by adding 1.5 weight-percent boric acid solution to the bottle. The cap is replaced, and the bottle and solution is reheated. Precipitated fluorides, as well as any residue, are dissolved by the fluoride-boric acid reaction. The resulting clear solution then is suitable for spectro-photometric examination or other analysis.

Jan 1, 1980

By Frank Miller

THE lower cost of producing oil from naturally flowing wells compared with pro-duction costs accruing from artificial lifting methods has stimulated much research, with the joint purpose of extending the natural flowing life of wells and of increas-ing the productivity of small wells. The laboratory investigation described herein was made to determine the effect of a slotted liner on the pressure gradient in the vicinity of the wall of a flowing well. Flow restrictions caused by the liner induce energy losses between the oil-bearing for-mation and the inside of the liner, which may be reduced by improved liner design, and thereby the flow capacity of wells may be increased. These losses have been evalu-ated for rectangular slots of different sizes, and means are suggested for reducing them. The dearth of information concerning the nature of the flow of fluids from uncon-solidated sands through small openings in the walls of pipes-as represented by the flow of oil from an oil sand into a slotted liner-is acknowledged. Although the bene-fits to be realized by operators through the use of optimum liners is just beginning to be recognized generally, Coberly1 in 1937 pointed out that the functioning of screen casing is an important factor in the pro-duction of oil. From his study on the selection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string de-serves continued study, especially with respect to the selection of perforations. The growing use of gravel packing result-ing from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded.

Jan 1, 1940

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016

By Aaron Miles

THE pressure distribution in a producing oil or gas reservoir has been obtained mathematically in a limited number of special cases where the boundary of the reservoirs are simple geometric figures with the wells conveniently located within them. Using some of the previous work as a basis, it can be proved that a number of additional problems of pressure distribution can be solved by use of soap film. This method is particu-larly applicable to a reservoir drained by a number of wells, or to a reservoir of irregular shape, or to both. Since this method obtains the pressure distribution, it also establishes the drainage boundaries of the wells. This paper derives the analogy between the equation representing the pressure distribution in a reservoir and the equation of the deflected membrane. It also describes the apparatus and the method of operation. The experimental method is employed to solve a problem whose mathe-matical solution is known and the results compared. These are found to be in good agreement. The method is applicable to any homogeneous liquid, compressible or incompressible, or to a gas, flowing in a reservoir of uniform thickness, permeability and porosity. The flow state may be either the steady state or the transient state wherein the density or pressure of the fluid in the reservoir declines at a constant rate.

Jan 1, 1938