Search Documents

By W. L. Chen

In the United States hydraulic cyclones have been used for thickening, classification and cleaning in coal preparation plants for many years. The cleaning cyclones presently in use are based on using a "heavy medium", such as a fine magnetite and water pulp. The latest addition to cleaning cyclones is the one which uses ?water only?, or simply called "Hydrocyclone". Just as was the heavy medium cyclone, the hydrocyclones were originated in the Netherlands (1, 2). Plants using hydrocyclones were built in Europe (3) and test plants were erected in Canada (4, 5, 6) and India (7). Roberts and Schaefer Company has built four plants using hydrocyclone circuits. One additional plant is in the process of construction.

Jan 1, 1965

By R. D. Carpenter, R. R. Smith, E. E. Sougstad

The Union Carbide Nuclear Co., in treating low-grade tungsten and molybdenum-copper ores at the Pine Creek mill near Bishop, Calif., employs flotation for the initial extraction of the valuable mineral constituents. These minerals consist of scheelite, molybdenite, and several of the copper sulfides including chalcopyrite, bornite, and possibly chalcocite. They occur in a gangue consisting mainly of quartz, pyroxene, and garnet, with minor amounts of calcite and fluorite. This assemblage of minerals presents an unusual grinding problem because of their diverse physical characteristics. Feed for the circuit is prepared from -6-in. ore by screening on a rod deck screen to remove the -5/8 - in. material. The+5/8-in. fraction is crushed in open circuit with a 5 1/2-ft Symons shorthead crusher operated at a closed- side setting of approximately 3/8 in. The screen undersize and the conecrusher discharge are then combined to constitute the feed to the grinding circuit. The ore is ground in 6 by 5-ft grate discharge ball mills operated in closed circuit with 54-in. spiral classifiers. The classifier overflow goes directly to the flotation section of the plant. Studies of the flotation circuits have shown that the maximum recovery of the tungsten, molybdenum, and copper minerals occurs in the particle-sue range from 100 mesh to approximately 400 mesh. Further, practice has shown that the ore minerals are effectively reduced to this size range if the total ore is ground to -48 mesh. The general objective of the grinding circuit then is to reduce the feed to -48 mesh with the production of a minimum amount of slimes. The purpose of this investigation was to ascertain how well the grinding circuit was carrying out this objective. The method used was to sample the various products in the grinding section, size these products accurately, and analyze the resulting sue distributions. SAMPLE PREPARATION AND SIZING TECHNIQUES Representative samples of the different grinding circuit products, namely, new feed to the ball mill, ball mill discharge, classifier overflow, and classifier return, were taken over a 24-hr period. The samples were then dried without being filtered to avoid loss of slimes. The percentages of solids in the different products were the following: new ball-mill feed, 95%; ball mill discharge, 82%; classifier overflow, 52%; and classifier return, 84% solids. Particle sizes were determined on each product by wet-screening an

Jan 1, 1962

By Long Meng, Yaodong Yi, Kuiyuan Chen, Zhancheng Guo, Yu Li

Blast furnace slag is the main by-product discharged in the iron and steel industry and contains considerable waste heat at dischargeing temperature between 1450 and 1550 °C. To fully utilize waste heat and slag, this study directly converted high temperature liquid Ti-bearing blast furnace slag into glass-ceramics via the “Petrurgic” method. Samples at different crystallization temperature were prepared and its influence on crystal phases, pore structure, and compressive strength were investigated via SEM, XRD techniques, and compressive strength measurements. Results showed that all glass-ceramic samples contained main crystals of perovskite, diopside and gehlenite and had a qualified mechanical performance with compressive strength above 100 Mpa, which meets the requirement of Chinese national standard for natural granite stone. With increasing crystallization temperature, pore size decreased, while the size of the perovskite phase firstly decreased and then increased with decreasing crystallization temperature. Samples had an optimum crystallization temperature of 1215 °C, maximum grain size and a densified structure with minimal pore defect.

Mar 1, 2018

By Eun Duck Park

The gold catalyst supported on iron oxide was prepared from gold dissolved in aqua regia by a deposition-precipitation method and applied to CO oxidation in the absence and presence of hydrogen. Some characterization methods such as X-ray diffraction (XRD), nitrogen adsorption, transmission electron microscopy (TEM), temperature programmed reduction (TPR), temperature programmed oxidation (TPO), and the pulsed CO chemisorption with temperature programmed desorption (TPD) were conducted to explain different catalytic activities of Au/Fe2O3 catalyst pretreated at different conditions. The particle size of gold was about 10 nm for Au/Fe2O3 calcined in air at 373 and 573 K. For complete CO oxidation, the decreasing CO conversion with a reaction time was observed at low temperatures but its initial catalytic activity can be restored by a heat treatment at high temperatures. This catalyst was quite active for the selective CO oxidation in the presence of hydrogen especially at low temperatures. In the presence of hydrogen, the deactivation was significantly diminished.

Jan 1, 2006

By J. L. Rodda

THE desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwilt1 has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier's method, described by Goerens,2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for as given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest proce-dure. The largest particle in a given portion is. then determined by Stokes' law:3

Jan 1, 1931

By Jeong-Hwan Kim

The liquid-liquid reactive process (solution process) is often adopted as a synthetic method for precipitated calcium carbonate (PCC) in laboratory studies for its simplicity in operation or ease in controlling process variables. Still, PCC are produced commercially by passing carbon dioxide through a milk of lime, i.e., by a gas-liquid reacting method (carbonation process). Few studies on the carbonation process have been conducted, since the process variables are interrelated and difficult to control compared to the solution process. In this study, both carbonation and solution processes were employed to study the polymorphs of calcium carbonate and growth rate of PCC crystals. The effects of the characteristics of limestone ores as a raw material in the synthetic system of PCC on the synthetic characteristics of PCC were also investigated. To control the nucleation rate in the synthetic systems, the shape factor was considered most important. Single-phase aragonite PCC could be synthesized under a variety of controlled experimental conditions such as ionic strength, solution composition, concentrations of additive ions, and temperature.

Jan 1, 2006

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By Juan Estrada, Mirtha Frómeta, Rubén Alcalá, Emilio Montejo, José Castellanos, Juan Berto, María Rivas

"The oxidized nickel ores from San Felipe deposit are composed mainly Smectites which gives to the pulps very unfavorable rheological .properties (cinematic viscosity and high shearing strength) for transportation processes (pumping), very low settling velocities and very low thickened pulps. These properties do not allow the preparation of high % solids, which affects the economic efficiency if a high pressure acid leach (HPAL) process is used. Pulps of close to 30% solids have very high BYS making pumping impossible. CIPIMM developed three technologies to solve these problems and to substantially increase the % solids in the pulps to be leached without a thickening step. These technologies are: • CIPIMM 2. At Preparation of pulps using additives. This method is based on the effect of some additives (inorganic salts) to improve the pulp’s properties. The use of this method allows increasing the % solids in the pulp up to 40% with good rheological properties • CIPIMM 2B. Preparation of pulps by thermal treatment of the ore previous to the preparation of the pulps. This method is based on the thermal destruction of the clays structure. Its use allows to obtain pulps with 50 - 60 % solids with excellent rheological characteristics. As a collateral effect, the Ni and Co grades increases by 10 - 15%. • CIPIMM 2C. Pulp preparation by chemical treatment. This method is based on the chemical transformation of clays, to obtain without thickening, pulps with 43- 45% solids and excellent rheological properties. The use of one of the three technologies depends on the chemical and mineralogical composition of the ores and the results of technical-economical evaluations to determine which one is the best alternative before running higher scale tests."

Jan 1, 2014

By Georges J. Kipouros

Anhydrous neodymium trichlorids (NdCl3), containing ~1 weight percent neodymium oxychloride (NdOCI) was prepared by the dehydration of neodymium trichioride hexahydrate (NdC13.6H2O). Dehydration of the hexahydrate was conducted in three steps. First, the hexahydrate was slowly heated in air to about 250 °C until all the low temperature water of crystallization was removed. In the second stop, the neodymium hydroxychloride (Nd(OH)2C1) fanned in the first step was decomposed by heating under argon to 430 ° C. Finally the salt was ground and then treated with HCl gas at 330 °C until practically all of the NdOCl was converted to NdCl3.

Jan 1, 1992

By Zefang ChenLi, Laijun Ma, Lei Mao, Fang Lian

"In our work, the preparation technique of high pure manganese sulfate directly from low-grade rhodochrosite ore (MnCO3) was studied and improved intensively, including the effective leaching process and the short purifying process. Based on the same ion effect, the repeated leaching of rhodochrosite with sulfuric acid is proposed to improve the solubility of Mn2+ and inhibit the dissolution of the impurities Ca2+ and Mg2+. Moreover, the repeated leaching process could make full use of rhodochrosite and lower the dosage of sulfuric acidas raw material. With the aid of theoretical calculation, Ba(OH)2 was chose to adjust the pH value of manganese sulfate solution, and BaF2 to remove Ca2+ and Mg2+completely in the process of purifying. The results demonstrate that the extraction ratio and the recovery ratio of manganese reached 94.3% and 92.7%, respectively, which shows the prospect of industrial application. In manganese sulfate production, the heavy metal impurities have been decreased to less than 1ppm. Moreover, the content of calcium, magnesium and sodium has been decreased to less than 20ppm, which meets the standards of high pure reagent for energy and electronic materials. Our study enlightens an approach to the sustainable application of low-grade rhodochrosite.Introduction Low-grade manganese carbonate ores (=14%) becomes gradually the main resources for exploitation and applications in China according to national mineral resources survey (Tan et al 2004 and Singh et al 2017). Therefore, the electrolytic deposition technique of rhodochrosite faces great challenges including low electrolysis efficiency, high-resource input and high-pollution discharge (Fu et al 2010, Michelis et al 2009, Zhang et al 2013). Recently, more and more amount of manganese series with high or super high purity such as MnSO4, MnO2, Mn3O4 and MnO is demanded with the development of energy and electronic materials. Due to low-grade ores containing multiple elements such as iron, silicon, calcium and magnesium, conventional preparation of manganese sulphate with high purity from electrolytic product is characterized by long production-cycle and high-energy consumption (Subrat et al 2011, Mpho et al 2013). By contrast, hydrometallurgical method combined with thermal decomposition, hydrothermal synthesis and sol-gel processes has been widely studied because of its high efficiency, low consumption and low cost (Chen et al 2008). But the key problem in direct preparation of manganese series form low-grade rhodochrosite is to remove completely the multiple impurities such as iron, silicon, calcium and magnesium (Liu et al 2014). So it is urgent to develop a sustainable alternative approach with character of short process, high efficiency and environmental friendly."

Jan 1, 2017

By Guo Gongyi

An extraction chromatography by which 99.99 % pure scandium oxide can be prepared from the starting materiel containing about 70% scandium oxide has been developed by taking advantage of some peculiar properties of the complex chemistry and extraction chemistry of scandium. The purification of scandium was performed at room temperature with relatively fast rates in two chromatographic columns. The preliminary separation of scandium from impurities was done by extraction chromatography using tri-butyl phosphate as the stationery phase in the presence of citric acid, and the nearly complete separation in the presence of perchloric acid. The scandium recovery was greater than 90 %.

Jan 1, 1989

By Katsumi Ogi, Hiroto Uchida, Masamitsu Sato, Atsushi Itsuki

"(BTMSE)Ag(hfac) (BTMSE = trans-bis(trimethylsilyl)ethene) was chosen as a suitable precursor for the XeCl laser (308nm) MOCVD of Ag. Iso-propanol solution of (BTMSE)Ag(hfac) was used as a liquid source for the liquid delivery method, high deposition rate 9nm/min at substrate temperatures of 100°C and 120°C were obtained at the vaporizer temperature of 90°C. This deposition rate is three times faster than by conventional bubbling method and life of the source and reproducibility of the deposition were also improved. Electric resistivities of the laser deposited film shows significantly low resistivity of 10-6Q-cm compared to 1 o-3Q-cm of thermal MOCVD film. These results indicates that the laser MOCVD is one of the effective method for the preparation of the high quality silver film.IntroductionSilver films are a potentially important metallization material in electronic and photonic devises due to their lowest resistivity (1.6µ0-cm) among the metals, high optical reflectance and chemical stability. The MOCVD technique has advantages to sputtering or evaporation in the point of conformal growth and better coverage on sharp steps and narrow gaps[l-2]. For MOCVD application, silver precursors must have sufficient vapor pressure without decomposition at their evaporation temperature. To achieve stable precursor gas supply, liquid delivery of precursor material is promising[3-4] especially for materials that have not enough heat stability and high vapor pressure like silver complexes[S-10]. Several new silver complexes for MOCVD and UV irradiation effect to their MOCVD silver film quality were reported by same authors[5]. In this paper new solvent system for liquid delivery system of silver MOCVD were investigated to suite XeCl(308nm) laser MOCVD application."

Jan 1, 1998

Domestic production of pyrite cinder reached 15.95 million tons in 2006. The pyrite cinder used in cement industry accounts for about 30% production. The remaining 70%, 11.17 million tons, was thrown away as waste, which brought serious environmental and resource problems. A new technology of composite pellet reduction-roasting and magnetic-separation (CPRM) has been developed to utilize pyrite cinder. Pyrite cinder sample, containing 45.56% Fe, 0.19% Cu and 1.45% S, was pelletized with addition of 5% composite agent in balling disc. Green balls after drying were reduced at 700~800 ? for 20min with 300kg/t pulverized coal injection in rotary kiln. After two stages of ball-grinding and four stages of magnetic separation, high grade magnetite concentrate with 66.23% Fe was produced, meanwhile impurities Cu and S was decreased to 0.048% and 0.053%, respectively. And iron recovery of 73.32%, desulphurization of 96.34% and decoppering degree of 74.73% were achieved. Key technique is that composite agent can accelerate reduction of Fe2O3 and transfer copper and sulphur into water-soluble inorganic salts, which can be removed during wet magnetic concentration. This new technology can be used to fully utilize pyrite cinder and produce high quality magnetite concentrates as feed for steel industry, which will help tackle the pollution problem of pyrite cinder and extend iron-bearing raw material sourcing for Chinese steel industry.

Jan 1, 2014

By Fuqiang Zheng, Feng Chen, Wenting Duan, Yufeng Guo, Tao Jiang

High-quality titanium-rich material is of significance in the development of titanium industry as it is the main raw material to produce sponge titanium and titanium white using chloride process. Activation roasting of titanium slag with high Ca and Mg contents as adding H3PO4 followed by acid leaching was investigated to prepare titanium-rich material. The effects of H3PO4 dosage, roasting temperature and time, hydrochloric acid quantity, acid leaching temperature and time on TiO2 grade and removal of impurities were studied. The results show that after the finely ground titanium slag roasted with 8% H3PO4 at 1000 for 2h, most Mg impurities in anosovite solid solution structure were converted into simple acid–soluble compounds. The impurities such as Ca and Mg obviously decreased when the hydrochloric acid concentration was 20%, leaching at 100 °C for 2h, from which a titanium-rich material containing 82.56% TiO2 and 1.15% (CaO+MgO) was obtained.

Jan 1, 2016

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great aggregates-preparation plant of the Six Companies, Inc. to supply. construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con¬tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great, aggregates-preparation plant of the Six Companies, Inc. to supply construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con-tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

By C. Barnett

"A description of the Geco orebody has been given by W .L. Brown and R.C.E. Bray (1). The mill flowsheet and equipment were described by M.J.S. Bennett, D. Wild and C. Lawton (2). Mill capacity is now 4, 150 tons per operating day of copper, silver, zinc and lead ore. A recent flowsheet has been published in the - Canadian Mining Manual (1966).Soon after the start of production in September 1957, it became apparent that large tonnages of sand would be required by the mine for backfill pruposes. Initial experimental work on the preparation of sand fill from the flotation tailings was begun in late 19 59. Cyclones of local manufacture, in a variety of sizes, were tested quite successfully. There were, however, several obvious advantages with some of the custom-built cyclones and a recommendation was obtained from the Techniquip Company. A single Krebs D-10-B cyclone was tested experimentally in 1960.INITIAL TESTWORKExperimental results showed that with our relatively coarse grind (in the order of 53 % minus 200 mesh) 75 - 80% of the flotation tailings could be recovered as backfill sand with one stage of treatment. Percolation rates of four inches per hour were obtained with cyclone inlet pressures in the range of 20 - 25 psi and feed densities of 20 - 23% solids."

Jan 1, 1968

By R. J. McLeod

"A new backfill plant was constructed in 1966 adjacent to the mill of Giant Yellowknife Mines. The reasons for the addition were to increase the storage capacity for sand fill, provide facilities for mixing cement with the fill for mine stope floors and provide a system for pumping fill to B -3 raise, a horizontal distance of 4700 feet from the mill. At the same time it was hoped to increase the density of the fill pumped underground.The plant consists of two only steel storage tanks of approximately 400 tons capacity of sand fill each. They are 17 feet in diameter and have conical bottoms. The cylindrical section is 28 feet high and the conical section 14 feet high. Each tank is fitted with water nozzles around the conical sections to remove solids at the required density. The water pressure on the nozzles is 150 lbs per square inch. The cyclones used to produce the sand back fill are located on top of the storage tanks. Five model Dl0B Kreb cyclones are used for this purpose. The vortex finders are 2 1/ 4 inch and the apex 1 1/4 inch. The cement silo or storage tank is located in the same building. It is a steel tank 17 feet diameter by 41 feet high with a conical bottom. The silo holds 250 tons of bulk cement, which is unloaded by air from a bulk highway carrier using 12 to 15 lbs air pressure. The cement is conveyed to the top of the silo, a distance of 70 feet from the ground by 450 lbs. of air.The mixing tank is a rubber lined steel tank 14 feet in diameter by 14 feet high. It is equipped with a Lightning Mixer supplied by Greey Mixing Equipment Ltd. The mechanism is driven by a 40 HP motor. The lower shaft is unsupported and is equipped with two 36 inch diameter axial flow turbine type rubber covered impellers. The backfill is discharged from the storage tank into the mixing tank by a 5"" x 4"" SRL-C pump powered by a 20 HP motor. A level control in the mixing tank regulates the rate of discharge of this pump through a Grinnell-Saunders automatic control valve. The cement silo is situated at such a height above the mixing tank to allow for a Rota-Lock, a small hopper and a cement feeder. The feeder is an Omega gravimetric belt type dry feeder with a Sensogram controller. The capacity of the cement feeder is 20 tons of cement per hour. The cement and backfill are mixed in the mixing tank at whatever ratio is required for the mine stope floors."

Jan 1, 1968

By Arthur S. Maynard

There was a tendency several years ago for the average coal producer to more or less sit back satisfied with the big utility and metallurgical mar¬kets with long term contracts, not realizing, or possibly not evaluating correctly the importance of the growing industrial market Even the companies which were producing coal for the industrial market were primarily interested in the larger industrial customer, not fully realizing that a large percent of the industrial coal sold was to plants using less than 15,000 tons per year. As a result, possibly, the greatest inroad made by competitive fuel was made in this group. The situation mentioned previously cannot be blamed entirely on the fact that the coal markets were not evaluated in their proper perspective. Some of the responsibility would have to be due to the situation that existed during the last war' and the period immediately following, when most of the coal was put to markets of higher realization, leaving the relatively small -industrial user-to get his fuel wherever he could. This usually would mean coal from some 'gopher hole" with fluxuating quality and supply. Therefore, it was not uncommon for some industrial customers to go to competitive fuels as soon as equipment and fuel were available. Fortunately, before this situation got completely out of control, the coal producers, realizing the seriousness of the problem, made available, usually through their sales department, combustion engineers and other specialists, to help the industrial user with his problems; The engineers usually found several problems, old equipment, use of incorrect size con¬sist, ash and fusion coals, lack of automation, fly ash and dust problems which increased cost and jeopardized the customer's relations with his employees and the public.

Jan 1, 1959

By Donald W. Scott

This paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the *preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizeis and organic dyes, and 35 parts of water are added to 100 parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the over-spray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1948