Search Documents

By Christopher Gammons

In developing countries throughout the world, gold ores are being processed by mercury amal-gamation, a technique long banned in the U.S. - unless a retort operation is used for mercury recovery - due to mercury toxicity and its effects on the environment. Amalgamation is a simple process that involves contacting a ground, slurried concentrate or ore with mercury in a slightly agitated vessel, usually for several hours, The amalgamated mercury is separated by gravity and then filtered through a fine cloth to collect the gold amalgam as a sponge, which is then fired to remove the final remnants of mercury and produce high quality gold. However, in Peru and other developing countries in South America and throughout the world, tailings are simply discarded into uncontrolled drainages and ponds and the sponge is fired in the open air. Clearly, in this case, environmental friendly and, to make matters worse, is typically conducted by family members of all ages without proper protection. Furthermore, the technique is inefficient, yielding approximately 50% gold recovery. For the past two years, faculty members from Montana Tech in Butte, MT, USA and the Universidad Nactonal del Altiplano in Puno, Peru have teamed to study the La Rinconada Mine Complex located in southern Peru approximately 100 kilometers north of Lake Titicaca and 25 kilometers west of Bolivia. The mining complex is over 5,000 meters above sea level and exists at the foot of a receding glacier in the Andes Mountains. A suite of soil and water samples collected in 2001 documented extensive Hg contamination in the Rinconada area [1]. The present paper summa¬rizes a follow-up investigation in July-2002, in which water samples were collected at numerous locations along the 200 km length of the Rio Ramis, from the Rinconada mine com¬plex to Lake Titicaca, In addition, we report new results of Hg analyses of fish from Lake Titi¬caca, The results of this study have relevance to safety and health concerns for the miners as well as people in downstream communities.

Jan 1, 2003

By Edward C. Clukey

A deep mixing method (DMM) foundation was selected by the Project Team for a very largeLNG facility in West Africa. As described in a companion paper, this foundation consists of alarge number of columns installed by mixing cement with in-situ soils. The foundations arearrayed as a variety of honeycombed type configurations which, if installed to desiredspecifications, can provide a robust foundation alternative. The foundation is capable ofdistributing loads and limiting settlements even if some of the soil in the columns is not fullymixed during installation. An important part of the overall quality assessment program,therefore, involved developing a testing program to verify the methodology. In addition theimpact of potential defects in columns on the overall foundation integrity had to be assessed.This paper describes some of the preliminary work done to establish the requirements for thequality assurance program. A key component of this program involved the samplingfrequency used to assess potential defects in the columns. To verify the column integrity 104-mm samples were taken continuously at a selected frequency through the 23 m longcolumns. The preliminary work described in this paper demonstrated that the appropriatesampling frequency depends on both the desired reliability level as well as the number ofdefective columns encountered during testing. Initial finite element analyses were performed to assess the extent that defects could occur incolumns within the honeycombed structure without adversely affecting the overall foundationintegrity. The results from this work demonstrated that the spatial location of the defects wascritical to properly assessing the foundation integrity. In addition to column sampling a load test was performed as part of the foundationverification process. The methods used to apply appropriate loads so that loads at thebottom of the columns approached design values are discussed in the paper. The results obtained from this preliminary study were then used to help develop a morecomprehensive assessment program, described in a companion paper, to determine therobustness of the DMM foundations for both the LNG processing facilities and a condensatetank.

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003

At Hilton Mine, 18 kilometres north of Mount Isa, the silver-lead-zinc sulphide bodies have undergone strong deformation in the form of folding and later faulting and brecciation in the hangingwall region of the mine. Variation in grades and widths over compara- tively short distances causes problems regarding accurate sampling of orebody exposures in underground development, and in defining confidence limits for the extrapolation of ore intersections in ore reserve calculations. The paper gives a preliminary insight into the problem of obtaining representative samples for exposed orebodies and discusses the sampling techniques employed. Results gained from these sampling methods could not be verified due to lack of individual bulk samples for comparison but strong evidence for precision was provided. INTRODUCTION In a developing mine like Hilton, accurate grade information is of extreme importance. Original grade information for a potentially viable ore deposit is gained from surface drilling, and initial ore estimates are calculated from the resultant ore widths and grades. After underground development has proceeded, the opportunity arises for detailed examination of orebody exposures, and the resultant assay grades and widths from sampling of these exposures may, in the long term,

Jan 1, 1976

By L. J. Hoover

The objective of this study was to assess the health and environmental impacts of fluidized-bed combustion (FBC) of coal, specifically as applied to baseload generation of electrical energy by utilities. The study* was a short-term effort that based its analyses on information derived from the experience of the group or quickly obtained from the literature. The approach was to compare Atmospheric Fluidized-Bed Combustion (AFBC) and Pressurized Fluidized-Bed Combustion (PFBC) with two current technologies: low-sulfur coal combustion (LSC) and flue gas desulfurization (FGD) used with high-sulfur coals. A wet-limestone process was selected as the FGD technology. The impacts compared involved not only health and environment but also sociology, resource use, and dollar cost. Conditions for comparison were centered around a nominal date of 1988, when initial operation of commercial AFBC plants may occur. The PFBC has a later introductory date, a nominal 1995 (its impacts relative to other competitive technologies now in the R&D stages were not compared.)

Jan 1, 1978

By C. Newman, R. C. Ray

Originated and developed in the civil tunneling industry, the Ground Reaction Curve (GRC) has provided a robust methodology for evaluating and designing ground support in both tunnels and underground mining scenarios. This paper presents a preliminary assessment in the utilization of the GRC concept for the evaluation and design of the pillar-support system with respect to overburden stress and displacement. This initial assessment will be based on and backed by past research on this topic. Underground mine instrumentation is planned for a longwall mine in the Appalachian coal field based on the research and findings in this paper to support the postulated hypothesis. INTRODUCTION Since the early 1970’s, the mining industry has evaluated the structural stability of a pillar by dividing an approximated pillar load by an approximated pillar strength. While this design methodology has served the industry well in the past, as modern mining operations continue to develop in more complex geological and geometric conditions coupled with market economics, industry professionals are in dire need of a modified stability assessment approach which considers both the stress condition and material displacements. Within the civil tunneling industry, the GRC approach has been successfully utilized in designing underground support measures that enhance the stability of an underground excavation. Through the incorporation of current industry knowledge and understanding of ground and support behaviors this paper looks to investigate into preliminary assessment for the development of a Modified Support Response Method (MSRM) to further improve the analysis of local and global underground stability. CURRENT PILLAR DESIGN METHODS AND THEIR LIMITATIONS Globally, multiple pillar design methods have been utilized in the design of underground excavations. Each of these methods approaches the calculation of pillar stability a little differently with respect to material properties, underground geometries and stress conditions. Analytical solutions can be used to determine the strength of homogeneous materials like concrete, but not in case of non-homogeneous and non-isotropic mineral deposits in a mine. These equations are often derived using empirical methods. Pillar strength is defined as the maximum resistance of a pillar to axial loading (Brady & Brown, 1985). The strength of mine pillars is typically estimated through indirect methods. In the past, researchers have correlated the strength of a given size and width of a rock specimen to the strength of a mine pillar. The first study on the effect of geometry on rock strength was done by (Bauschiger, 1876) on Swiss sandstone samples. Since then several empirical equations to determine pillar strength had been published by many researchers like (Bunting, 1911), (Griffith & Conner, 1912), (Greenwald, Howarth, & Hartmann, 1939), (Holland & Gaddy, 1957), (Evana, Pomeroy, & Berenbaum, 1961) and (Holland C. , 1964).

Jan 1, 2019

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

By T. A. A. Quarm

The concept of a continuous zinc smelting process which employs submerged combustion of coal char for both heating and reduction is described. An estimate of the results of smelting a marmatitic zinc concentrate indicates that both the operating and construction costs would be lower than those incurred in processes now in commercial operation. The results of smelting a complex zinc-copper concentrate are also estimated, but no simple commercial process exists with which they can be compared

Dec 1, 1971

By Guerry H. McCullen, Bruno Despujol

Quartz and phosphate grains from concentrates and ores from Atlantic Coastal Plain sediments often are wholly or partially coated by humates. Coatings were studied in situ using infrared microscopy, by transmission Fourier transform infrared of extracts, and scanning electron microscopy. The 14C age of the coatings is about 20,000 years, much younger than the mineral substrates. Coatings on double flotation concentrates indicate that the conditioning pH may be too low, allowing coated quartz grains to follow phosphate grains through beneficiation. Organic matter from coatings may contribute to processing problems as well as affect final product quality.

Jan 1, 1999

By Ramiro Escudero

Michoacan?s beach sands with interesting concentrations of ilmenite were studied to produce titanium by hydrometallurgical techniques. Nevertheless, among titanium species, there are different additional components of Michoacan?s beach sands which could be of interesting applications. Some of them are likely to be applied for the manufacture of nanocrystalline ceramics. Although, the most applied mineral dressing to treat these kind of sands, that contain magnetic species (i.e., ilmenite, magnetite), is a combination of gravity separation and magnetic separation, it could be of a great deal of benefit to apply the information regarding the surface characteristics of the sands? components, in order to study the application of flotation technologies to separate selectively those species with commercial value.

Jan 1, 2006

By George R. Huebner

The White Pine Copper Company, subsidiary of Copper Range Company, is located in the Upper Peninsula of Michigan. The offices, plant, and mine are six miles south of Lake Superior in Ontonagon County. Employing 1700 people, White Pine is the largest single industry in the Upper Peninsula. 970 underground employees produce 16, 700, tons of ore daily. From this tonnage 363,400 pounds of refined Lake Copper are produced in various shapes as specified by the customer. The following paper explains the geology of the ore body and briefly outlines present mining methods. It enumerates the reasons for considering longwall mining of a hardrock* ore body and the preliminary investigations leading to the decision to undertake the initial test panel. Selection of the initial test panel location is covered in detail. Equipment choice and reasons for that choice are described as well as selection and training of personnel.

Jan 1, 1964

By J. P. Savely, D. E. Nicholas, R. D. Call

Progress in the technology of slope design over the past 15 years now permits the selection of rational slope angles if suitable data on geology, hydrology, and rock properties are available for a specified project. Although a full-scale slope design study remains the best course of action, there are situations where an extensive study is not feasible due to time or budget constraints. Two typical examples are: (a) selecting pit slope angles for a preliminary feasibility study at the exploration stage; and (b) coping with a slope failure in an operating mine. In both instances, slope angles must often be chosen on the basis of data that are currently available or can be readily obtained. All too often during exploration programs, a feasibility study is initiated shortly before the decision deadline to drop the property or proceed to purchase. If the only existing data at this point are a few cross-sections at odd angles showing ore and waste contacts or a dog-eared map of the surface geology, there may not be time to collect and organize sufficient information for the design of slope angles. On the other hand, if during the drilling program geologic cross-sections were constructed and the structural data compiled in tabular form, rational slope angles could be computed within the allotted time.

Jan 4, 1977

By R. D. Call

During the past fifteen years considerable progress has been made in the technology of slope design. It is possible to design rational slope angles if suitable data on geology, hydrology, and rock properties are available. It is of course preferable to conduct a full scale slope design study, but there are those situations where a full scale study is not feasible because of time and budget constraints. In this paper we will treat two situations: (1) choosing slope angles for a preliminary feasibility study at the exploration stage; and (2) dealing with a slope failure in an operating pit. In these instances slope angles must often be chosen on the basis of available or readily obtained data. In an exploration program all too often a feasibility study is initiates just a few months prior to the decision deadline to drop the property or to exercise an expensive purchase option. If all that is available at this point are a few cross sections at odd angles showing ore and waste contacts and a dog-earred map of the surface geology there may not be time to collect and organize enough information for design of slope angles. On the other hand if during the drilling program geologic cross sections are constructed and the structural data is presented in tabular form, rational slope angles can be determined within the allotted time. Certain types of data can be collected only at specific times during a project. Two prime examples are logging fracture intensity and collecting samples for rock testing before the core is split. It is particularly disheartening to ask to see the core and to be shown a tattered cardboard box filled with plastic bags of sample pulps.

Jan 1, 1976

By Vi-Duong Dang

Lithium requirements in the next few decades for batteries and controlled thermonuclear fusion reactors (CTR) may exceed the availability of the current mineral and brine reserves. It is thus prudent to search for new reserves and resources to satisfy these and future lithium applications. The lithium content of the waters from the Smackover oil field. located in the Gulf Coast region of the United States, ranges from 100 to 500 mp/l and could represent a substantial new reserve. Experimental evidence described in the literature indicates that a specific chelating agent dipivaloylmethane (DPM), of the diketone type, has a specific selectivity toward lithium in the presence of other metal ions in aqueous solutions. Based in part on this unique property of dipivaloylmethane, a conceptual design of a full-size plant to extract lithium from the Smackover brine is presented in this paper. This study includes alternate flow-sheet development, design information on the major units of the process, energy requirements, and an economic analysis of a facility capable of producing 106 kg of lithium per year. The economics of three different process concepts depend primarily on the amount of water needing to be evaporated from the initial oil-field feed waters in concentrating the brine. The results, as a function of production rates, are indicated only in a general manner.

Jan 1, 1978

By Donovan F. Symonds

INTRODUCTION The selection of the optimum coal preparation plant flowsheet is a vital part of the development of a new plant or the expansion of an existing facility. Selection of an inappropriate flowsheet or individual equipment items can result in costly production losses, or needless expenditures or redundant or oversized equipment. The accuracy of the flowsheet selection process is, like most decisions, heavily dependent upon the amount, reliability, and quality of the database. A flowsheet which is based on simple borehole information from an area that has experienced little or no previous mining activity must necessarily include significant allowances for uncertainties. However, a plant which is to be built at an existing mine with good information on run-of-mine (ROM) coal quality, as well as bulk washability data and accurate projections of future quality, can be optimized. The following chapter will describe the processes which should be followed to select the most appropriate flowsheet for each unique operation. They include: 1. Examining and adjusting the washability database to reflect the ROM feed. 2. An evaluation of clean coal specifications. 3. Selection of the level of washing required. This includes no washing, if the coal is already at the desired specification, all the way through to complex total washing circuits for metallurgical grade coals. 4. Selection of the appropriate circuit such as dense medium bath vs. Baum jig. The most appropriate circuit is generally determined on the basis of economics. An approach for performing the evaluation will be desired. 5. The steps that need to be followed to develop a balanced plant flowsheet. ADJUSTING WASHABILITY DATA It is not unusual to have as many as 10 to 20 sets of washability information available for a particular mining property. These may be a combination of core and bulk samples or all bulk samples. In the latter case, they may also be face and/or ROM samples. It is necessary to reduce all of this information to a single set of washability data that is representative of the mean feed to the proposed preparation plant. This set is used to compare the clean coal yield and quality characteristics of the various flowsheet options. The term "representative" has some serious negative connotations. It is recognized that ROM coal quality will vary throughout a mine. However, over a period of 250 to 350 days per year, certain trends can be established. If possible, this "representative" sample should be close to the coal quality of the mean daily sample in terms of raw ash and sulfur contents, clean coal yield, and clean coal ash and sulfur content. If possible, this sample should be within the

Jan 1, 1991

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By C. M. Chang, H Gu, J. A. Barrera-Godínez, T. J. O’Keefe

The inability to economically separate Fe3+(aq) from a variety of liquid effluents is a major Concern for the primary metals industry. A unique solvent extraction process, galvanic stripping, has been developed to address this problem. The galvanic stripping of iron from D2EHPA using only a 5~10 g/L H2SO4 solution is achieved after Fe3+ is directly reduced to Fee, in the organic phase using zinc metal additions. To date, the primary focus of the laboratory research has been on optimizing the parameters that control iron removal. The results from these studies have now been, used to make a preliminary design for a continuous flow process that is envisioned for zinc industrial applications. Specific quantitative data are shown for the use of a Zn-Ph cellos° in the iron-reams al process. Some introductory results on electrochemical potential measurements and impurity distribution with solution cycling are also giiven.

Jan 1, 2000

By Gordon T. Clark

The preliminary design of four mined stations and 7.2 km (4.5 miles) of tunnels for Seattle’s light rail transit system is described. Constraints that influenced the design and options that were studied are discussed. The hilly post-glacial soft-ground geology of the Puget Sound Region pushed the alignment deep. Mined underground stations at depths up to 75 m (250 ft) and shafts with excavated diameters of 20-m (65-ft) are required. A 460 m (1,500 ft) sub-aqueous crossing of Portage Bay and undercrossing of an active 12-lane multi-level freeway were two of the more significant design constraints.

Jan 1, 2001

By Larry D. Wayland

Almost 100 sedimentation ponds were conceptually designed for a large surface mining study area in northeast Texas. An approximate procedure was developed to economically estimate construction quantities in order to predict surface water control costs. This procedure utilized site-specific empirical relationships developed from detailed analyses on a representative number of proposed sedimentation ponds. Use of these equations provided earthwork volumes, and spillway pipe lengths. The procedure developed for this study is presented along with the results of a verification analysis.

Jan 1, 1983