Search Documents

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

By Bratt G. C, Horsham T. R, Langlois D. R

Mercury is precipitated from weakly acidic sulphuric acid plant waste liquor at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited. Factors determining the choice of process and reagent, as well as details of process development including scale- up, and the time scale of implementation are outlined. The plant is designed for a maximum flow of 120 m3/h.of liquor containing mercury and saturated with sulphur dioxide. Mercury is precipitated by fluidised beds of aluminium pellets contained in lead columns. Liquor is then clarified with plate and frame presses. Experimental work on the mercury precip- itation reaction was conducted in three phases involving a scale-up of 100 times in equipment size. Extensive pilot filtration work was carried out on a 1 m2 press. Scale-up of 120 times was required for specification of plant filters. The basis of scale-up is outlined.

Jan 1, 1977

By F. A. Schaufelberger

Early work on chemical precipitation of metals from metal salt solutions is reviewed. The chemistry and thermodynamics of precipitating copper, nickel, cobalt, and cadmium metals by reaction with hydrogen are discussed. Mechanisms of metal precipitation, nucleation, growth, and agglomeration are reviewed, as well as some solubility phenomena of gases and solids at elevated temperatures. Experimental data presented deal mainly with the reaction of copper sulfate solution with Hz.

May 1, 1956

By C. Lottering

Copper sulphate solutions are produced during the pressure leaching of first-stage leach residue in a typical base metal refinery process. Apart from impurities such as selenium and tellurium, this leach solution also contains other precious metals (Rh, Ru, and it) due to dissolution in the pressure leaching stage. Selenium and tellurium are removed from the leach solution by precipitation with sulphurous acid, since these elements negatively affect electrowinning. This study investigates the feasibility of modifying the Se/Te precipitation process step to achieve significant rhodium precipitation in addition to selenium and tellurium precipitation, in order to reduce the rhodium inventory of the process. Thiourea, S02, formaldehyde, formic acid, and sodium thiosulphate were evaluated to determine which of these reagents would achieve the highest Rh precipitation. Based on these screening tests, SO2 and thiourea were selected to be used as precipitation reagents in optimization tests. During these optimization tests, the operating temperature (80 to 150°C) and the amount of reagent added (80 to 140 per cent excess) were varied to evaluate the effects that these operating conditions have on the precipitation behaviour of Rh as well as Se, Te, Cu, and Ni, and to propose appropriate operating conditions. It was found that thiourea resulted in good Rh and Se precipitation (typically in excess of 90 per cent), but precipitated noticeably more copper and nickel from the solution than when SO2 was used. In addition, thiourea had poor Te removal characteristics. SO2 achieved a maximum of 70 per cent precipitation of the rhodium. Faster kinetics and a larger extent of Te precipitation were, however, observed when using SO2 compared to thiourea.

Jan 1, 2012

By N. Geoffroy, E. Benguerel, G. P. Demopoulos

In the late 1990s, a chemical process to remove mercury and selenium from weak sulphuric acid solutions was patented and implemented in the CEZinc refinery in Valleyfield, Quebec. The CEZinc process comprises two stages. In the first one, sodium sulphide is added to the weak acid solution in order to precipitate the soluble mercury. The solution is then treated with sodium dithionite in order to reduce the selenium to elemental form. Because of recent changes in the composition of the industrial solution, a project to study the background chemical reactions was started. In this paper, a review of the background chemistry is presented on the basis of several eh-pH diagrams on one hand, while on the other experimental results are reported dealing with the reaction of selenium (IV) species with either dithionite, sulphide or a combination of the two. According to this work, elemental selenium enjoys a wide pH-eh range stability with selenium sulphide being metastable. Selenium (IV) in single metal synthetic solutions was found to be reduced - to elemental state - at ambient temperature down to ppb range with dithionite as long as the stoichiometric ratio (dithionite/selenium) was in excess of two and the pH < 1.7. Under these conditions the reaction was very fast reaching completion within one minute. Sodium sulphide proved equally effective in reducing selenium (this time as selenium sulphide) to ppb range from single metal solutions. However, in mixed Se-Hg solutions deviations from this "ideal" behaviour was observed resulting in higher levels of residual soluble selenium left in solution.

Jan 1, 2008

By J. A. du Plessis, C. Dorfling

Selenium, tellurium and other precious metals (OPMs, namely Rh, Ru and Ir) dissolve in the final leaching stage of base metal refineries. Se and Te are typically removed from the copper sulphate leach solution by precipitation with sulphurous acid. Recovery of dissolved OPMs is desirable because it will reduce OPM inventory and losses. Thiourea is an effective OPM precipitation reagent, but yields insufficient Te removal. Copper is known to enhance Te precipitation when using sulphurous acid as precipitation reagent. The primary objective of this project was to evaluate whether simultaneous precipitation of Se, Te and OPMs using thiourea with metallic copper as precipitation reagents is possible. Batch precipitation tests were performed to evaluate the effect of temperature (50 – 70°C), thiourea addition (160 – 430% excess) and copper addition (2 – 8 g/L) on Se, Te and OPM precipitation. Increasing the temperature from 50°C to 70°C resulted in an average increase of 55.6 percentage points for Se precipitation and 13.5 – 23.5 percentage points for OPM precipitation. The copper addition did not have a significant impact on the precipitation behaviour. Increasing the thiourea addition increased the precipitation of Se and Te, especially when the copper addition was low; Rh and Ru precipitation also increased with up to 10 and 12 percentage points, respectively. Despite these observations, the precipitation of Se was significantly faster when no thiourea was added. It is not currently clear why thiourea appears to inhibit the Se precipitation by reaction with metallic copper. In general, Te precipitation was low (less than 30%) at the conditions investigated. Simultaneous precipitation of Se, Te and OPMs at temperatures below 80°C does not appear to be a viable option; a multiple stage operation for sequential removal of Se and Te with copper followed by OPM precipitation with thiourea would be required.

Jan 1, 2016

By Jae-Chun Lee

Di-2-ethylhexyl phosphoric acid (D2EHPA) is widely used for separating rare-earth elements. In commercial plants, rare-earths are usually stripped from loaded extractant streams using mineral acid, then precipitated as oxalates. Many rare-earth uses demand specific powder characteristics, which are obtained by secondary processing. This paper demonstrates the feasibility of combining the stripping, precipitation and powder processing stages, thereby achieving considerable savings. MEHPA solutions were loaded with yttrium, then emulsified with oxalic acid-HC1 solutions to precipitate yttrium oxalate, which was readily calcined to yttrium oxide. The precipitation kinetics and yield were sensitive to process conditions. The morphology and size of the yttrium oxalate powders varied with the concentrations of D2EHPA and oxalic acid, and the presence of SPAN 60, which affected nucleation, growth, and the emulsion characteristics.

Jan 1, 1992

By María Cristina Ruiz

Hematite precipitation is a convenient alternative for the removal of iron from leaching circuits because of its chemical stability, high density and high iron content. The precipitation of hematite from ferrous sulfate solutions was studied in a batch reactor. The precipitation occurs by two sequential steps: oxidation of the ferrous to ferric ions followed by hydrolysis of the ferric to hematite. The main objective of this study was to determine the effect of the main operating variables on the rate of two steps of hematite precipitation. The variables studied included: stirring speed (100 to 600 rpm), temperature (160 to 200 ºC), concentration of sulfuric acid (1 to 10 g/L), initial iron concentration (1 to 15 g/L), and partial pressure of oxygen (1 to 6 atm). The sulfur content and the particle size of the solids that precipitated under various conditions were also determined. The results showed that at low temperature and high acid concentration the rate of Fe3+ hydrolysis is the step that controls the overall process. The variable that affects most the rate of Fe2+ to Fe3+ oxidation and the rate of hematite precipitation is the temperature.

Jan 1, 2008

By Taiping Lou

The effects of slag composition, additive agents, and heat treatment conditions on the perovskite (CaO ? TiO2) crystal morphology, the precipitation behavior, the crystal growth and the volume fraction (VF) in the Ti-bearing blast furnace slags were investigated. The morphology of perovskite is dispersed dendriform in molten slags. The crystal growth mechanism of the remelting of fine dendrites and the coarsening of larger grains exists throughout the solidification of molten slags. With the temperature decrease, the VF was increased and Perovskite transformed from fine dendrites to coarsening ones or equiaxed grains. The lower cooling rate can increase the VF and coarsen the grain obviously, while higher cooling rate will decrease the VF and reduce the average equivalent diameter (AED) of Perovskite. When .increasing the content of CaO and Fe20}, the VF can increase obviosly. However, high basicity will give rise to the increasing of viscosity of slag, which result in the reducing of the AED. The experimental results showed that additive CaF2 and MnO can efficiently decreased the viscosity of the slags, and obviously improved the morphology of perovskite and promote growth.

Jan 1, 2000

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

By J. W. Halley

COPPER has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is diffi-cult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile" steels. They were designed for use in the "hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels."

Jan 1, 1940

By Vernon Read

Among the technical problems in AEC&apos;s Project Plowshare is the necessity of determining the precise effects of nuclear blasts in all kinds of ground formations. This calls for extensive in-situ sampling with full core recovery. In the exploration drilling that often precedes a new test detonation, the AEC and its contractors have applied both novel and established sampling techniques in many new ways, giving improved core recovery and reduced costs in all subsurface sampling and testing. Unique among these new techniques is one that achieved full recovery and virtually undisturbed samples from near-surface layers of unconsolidated boulder-strewn alluvium. This approach involves a combination of oilfield and mining core drilling equipment. Oilfield heavy drill collars, rotary stabilizers and thick, vibration-reducing oil emulsion drilling mud were used in combination with the precise hydraulic feed control, fast (over 300 rpm) bit rotation, light drilling weight, hard rock core barrels and multi-step diamond bits that are common in mining industry diamond drilling.

Jan 8, 1963

By C. Partouche, T. Bernard

Blasting engineers are mainly concerned about fragmentation issues. Even further, this is the final goal of using explosives. A lot of models have been developed for controlling fragmentation distribution, but most of the time, they are based on physical phenomena using field data as input for rock characteristics. Fragmentation is a result of two phenomena: waves from the borehole, damaging and cracking the rock, and gas pressure, widening those cracks and spreading out rock fragments. This model simulates the P wave escaping from boreholes and the cracks created by these P waves. It takes into account rock characteristics, provided by digital imaging, and explosive characteristics coming from VOD measurements. What we need to focus on, is the interaction of P waves coming from each borehole related to different timing sequences. This paper presents several simulations that show the influence of the timing and the sequence accuracy on the fragmentation distribution.

Jan 1, 2002

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: " &apos; What device does he bear on his shield?&apos; asked Ivanhoe. &apos;Something resembling a bar of iron, and a padlock painted blue on a black shield.&apos; &apos;A fetterlock and shacklebolt azure&apos;, said Ivanhoe"-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By T. A. Rickard

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: "&apos; What device does he bear on his shield?&apos; asked Ivanhoe. &apos;Something resembling a bar of iron, and a padlock painted blue on a black shield.&apos; &apos;A fetterlock and shacklebolt azure&apos;, said Ivanhoe "-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be\ proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

At Cliffs Natural Resources Ltd (CNR) crushing and shipping sample stations, precisions are estimated for the sampling, preparation and measurement stages of iron ore sampling in accordance with ISO 3085 (2002). In this Standard, gross duplicate samples are prepared at each of the three stages, yielding eight measurement assays. Appropriate calculations of the differences between assay pairs are then made to estimate precision of each stage of sampling. The International Standard for checking precision in iron ore sampling, ISO 3085 (2002) prescribes a method for identifying outliers that is ambiguous and possibly inappropriate. The procedure also makes an unnecessary implicit assumption, that the differences between assay pairs are normally distributed. The Anderson-Darling statistic is used to demonstrate that in some cases the assay pair differences have distributions significantly different from normal. When applied at CNR as specified, the Standard leads to precision estimates well below the expected values, thus overestimating the sampling method&apos;s capability and limiting the opportunity for real process improvement. This paper suggests an improved method of estimating sampling, preparation and measurement precision. A bootstrap procedure is used to estimate confidence limits for the calculated precision estimates. The proposed method would be suitable for testing blasthole precision. The discussion is supported by extensive simulation modelling of realistic data.

Mar 1, 2010

By Jan W. Merks

"The settlements between mines and smelters are based on the mass of metal contained in concentrate lots. The mass of contained metal is a function of the wet mass of a lot, and its moisture content and metal grade while the variance of the mass of contained metal is a function of the same variables and their variances. Uncertainties in the measurement procedure applied to estimate each variable are quantified in terms of precision and bias. The absence of bias and an acceptable degree of precision are the keys to effective risk analysis and loss control.ISO Technical Committee 183-Copper, Lead and Zinc Sulfide Concentrates, has developed standard methods for sampling and weighing, estimating precision and testing for bias, the determination of mass loss on drying, the calculation of the mass of contained metal and its variance, and various analytical methods for major and minor metals. The variance for wet mass is calculated from the precision of the scale while the total variances of moisture and grade are estimated from pairs of interpenetrating primary samples. The variance of contained metal can be calculated either from mine data or from smelter data but the risk associated with the settlement is largely determined by the absence or presence of bias and the variance of differences between exchange assays.ISO/TC 183 does not deal with precision and bias for exchange assays but is developing guidelines to determine realistic splitting limits. Given that the exchange of assays between mines and smelters accounts for a large part of the risk associated with the settlement, precision and bias for exchange assays should be measured and monitored. The need for umpire services can be reduced by applying statistical quality control (SQC).Calibrating static scales, moisture balances and analytical balances, bias testing of sampling methods and sample preparation procedures, estimating the variance of a single variable or the variance of a function that a set of variables defines, and monitoring precision and bias for exchange assays, are the quintessence of metrology, the science of measurement, when applied in mining and metallurgy."

Jan 1, 1995

By Bill Rose, Alan Foster

This paper will outline blasting as undertaken at the Flour Mill project in the Georgetown area of Washington, D.C. It will discuss the vibration and blasting problems found in blasting in high risk and highly populated areas, and the day to day methods used to minimize damage potential and still maintain adequate fragmentation.

Jan 1, 1979

By B Mohanty, M Alam, F Gauthuer

A series of eleven full-scale production blasts has been earned out in a limestone quarry to study the effect of delay interval and its precision on overall blasting performance. The quarry employed ANFO and cartridged aluminized emulsion in 75 mm diameter boreholes with 2.6 m burden and 2.9 m spacing on a 6.7 m bench. Both V-cut and echelon designs were studied. The types of detonators tested were regular short period electric detonators with expanding delay intervals, a more precise pyrotechnic-based electric detonator (EXADET) with a fixed (25 ms) delay interval, and the ultra-high precision electronic delay detonator (EDD) with constant (but site-selectable) delay interval. The various techniques employed to assess the blast results are described, and the performance of the three types of detonators compared. The use of both EXADET and EDD lead to improved blast results in echelon design. Of the three delay intervals (25 ms, 38 ms, and 50 ms) studied, the best results were obtained with EDD with a 38 ms delay interval, which translates into a delay of 38 ms/m of effective burden. The results also show the need for modification of current V-cut delay designs to derive full benefits from these high precision detonators.

Jan 1, 1991