Search Documents

By Vladimir M. Korolev

The field studies conducted at the experimental-production sites allowed to develop the technology of arranging drilling piles in loess subsiding grounds over 25 m deep and over 250 mm in diameter, to select optimal compositions of flush fluids, to assess the carrying capacity and field of use of the piles under test and to produce a special equipment. The dependence of the ultimate axial pressing-in load on pile driving into the non-subsiding section, its diameter and method of fulfillment, as well as the ground moisture dependence of the specific ground resistance along the piles' side surface within the limits of the subsiding section were determined. The study results allowed to reduce the length of the work piles and the number of bars in the reinforcement frames. The obtained experimental data enable to give a preliminary assessment of the piles' carrying capacity under complicated engineering-geological conditions of subsiding grounds.

Jan 1, 2002

By X. J. Guo, H. X. Li

The biological heap leaching at Zijin copper mine is currently the largest industrial application of biohydrometallurgy and one of the earliest mines to develop biological metallurgy technology in China. Since 2001, through demonstration plant and different expansion stages, it has been developed to produce 20,000 tons cathode copper annually. However the ore grade of heap leaching gradually decline year by year with copper grade average at around 0.23% now. The copper mineral is mainly the secondary copper sulfide, and symbiosis with higher content pyrite, the sulfur and iron contents is about 15 times as copper in the ore (S/Cu>15), so the acid and iron treatment of leachate, extractant and acid mine waste water is a great challenge. Combined with located in the rainy area of southern China, huge amounts of over 10 million cubic meters acid drainage need to be treated every year, so the recovery of copper from waste water as well as low grade ore is one of the characteristics of this process. This paper in general introduced the operation of heap leaching, solvent extraction, stripping and electrowinning process in Zijin mine, summarized the experience of production and technical practice, and discussed the methods of heap construction, leaching rate enhancement, third phase formation and treatment, mine effluent treatment, resource recovery and heap slope reclamation. INTRODUCTION The Zijinshan gold and copper mine is located in southeast China, Fujian province, and the typical distribution characteristics of gold and copper deposit are "upper gold and lower copper", both are large porphyry deposits. By the end of 2017, the accumulated proven reserves of available gold resources were 318 tons, copper are 2.15 million tons, and the prospective reserves of copper are more than 5 million tons. The gold mining is open pit while the copper mining is open pit and underground. The cut-off grade of gold mining is 0.15 g/t, and that of copper mining is 0.15%. A large number of very low-grade gold ores (grade <0.30 g/t) adopt a combined ore-dressing process of “partial crushing/ore washing/reprocessing/heap leaching (overlying)/ carbon slurry" independently developed, while flotation and bio-heap leaching are adopted for copper mine. Among them, copper ore with more than 0.25% copper content enters the flotation system to produce copper concentrate, while that of less than 0.25% copper content is processed by bio-heap leaching, solvent extraction and electrowinning. Zijin biological heap leaching plant is the first mine in China to achieve the scale of annual output of ten thousand tons of cathode copper since 2006. In 2008, the solvent extraction and electrowinning system were expanded, now with a daily processing capacity of 20,000 tons of ores, an annual output of 20,000 tons of cathode copper, the expanded plant is the largest biohydrometallurgy plant in China.

Jan 1, 2019

By Cen Guoji

The foundation of bored pouring concrete pile have been adopted in the bridge engineering of China since early in the sixties. They demonstrated tremendous technical advantage and achieved notable economic benefit. With improvement of bridge technique including construction technique work equipment, design theory, examination in quality and applicable range etc, the pile diameter became bigger and the foundation changed from shallow to deep-water. This paper examples Jiujiang Bridge of Guangdong in China, which is single-tower cable-staged bridge, total length of 1675m, and expouds adopted successfully the foundation of variable section large bored pile (upper part d=3m, central part d=2. 4m and lower part d=2m) on the conditions of complicated technique that the load is tremendous (it require specially to resist 12000 kN ship impact) and the piles have free length 30m. The paper will be to describle design project and construction practice of pile foundation with variable section, and to compare schemes of equal section pile and pile in sinking-well.

Jan 1, 1991

By John H. Melvin

THE Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. GEOLOGY Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its uncemented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable - slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1947

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) technique is widely known as soil mitigation technique with small ground displacement during installation comparing with other techniques. Some projects involving sensitive structures, however, require smaller impact than in conventional technique. In order to reduce ground displacement during DJM installation, this paper introduces systematic mixing technique, RD-DJM (Reducing Displacement – Dry Jet Mixing). RD-DJM is characterized by injection nozzle on the rim of mixing blade and fin plate on mixing shaft. These devices contribute efficient collection of injected air toward mixing shaft and result in reduction of ground displacement. The authors demonstrate successful performance of RD-DJM indicating difference between conventional installation and RD-DJM technique.INTRODUCTIONThe Dry Jet Mixing (DJM) method is one of the most common techniques in Japanese deep soil mixing field and characterized mechanical mixing of powdery binder with in-situ ground (dry-mixing technique). It is widely believed that DJM Method has great advantages in less quantity of binder to achieve the desired strength and less waste generation during installation.DJM method can meet the required strength with less binder content than wet mixing. And volume of binder of dry mixing is absolutely less than wet-mixing injecting considerable volume of binder slurry. This means that dry mixing causes less ground displacement compared with wet mixing.As the medium for forced feeding of the binder, the DJM method uses compressed air, which is blown from the mixing blade nozzles to scatter the binder and then recovered through the periphery of the mixing shaft to the ground surface. Because the binder is injected outward from the injection orifice at the root of the mixing shaft, a part of the air may escape to untreated areas due to the blockage of air recovery path around the mixing shaft. Figure 1 illustrates possible escaped air and leakage around installation location."

Jan 1, 2015

By W. Carter, P. Chaubal, K. Spaleck, M. Schoeman, J. Bobek, W. Seegers

Keywords: Pyrometallurgy, steel, hearth, blast furnace The Mittal Steel Company operates about 36 blast furnaces on four continents. Furnaces range from 1100 m3 to 4800 m3 inner volume. The focus of the group is to push for increasing productivity and increasing campaign life. This has been especially challenging, as many of these furnaces were not equipped for long campaigns during their prior rebuilds. Monitoring and operating practices have to be modified to match the new philosophy. Mid-campaign hearth repair strategies and hearth design philosophies have had to be reconsidered. The paper describes experiences with the current hearth designs and measures taken for hearth life extension. Additionally, the philosophy of recent hearth re-designs is discussed.

Jan 1, 2006

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By G. B. Shea

Among the many engineering problems directly related to conservation in the petroleum industry, that of crude-oil emulsions continues to be important. Emulsions of water and oil always have constituted one of the most serious forms of waste in the oil fields, and the necessity of dehydrating emulsified crude petroleum to obtain marketable or pipe-line oil confronts operators in many fields with a major operating problem. In 1926 the Bureau of Mines published a comprehensive treatise s on oil-field emulsions dealing with field conditions, practical methods of dehydration, and physicochemical characteristics of the formation and resolution of emulsions. Although this bulletin is still available and may be obtained from the Superintendent of Documents, Washington, D. C., and although its contents are a valuable reference on the subject of emulsions, knowledge regarding the physical properties of emulsions and the phenomena of dehydration has increased greatly within the last decade. With the information gained through continued scientific research, substantial improvements have been made in the art of resolving petroleum emulsions. Moreover, in recent years there has been a growing realization of the importance of emulsion-preventive measures that has led to more critical examination of the causes of emulsions and methods of eliminating or at least reducing the degree of emulsification. Conditions causing agitation and commingling of oil and water and the formation of "cut oil" often are within the control of the producer, thereby making it possible to utilize preventive or remedial measures by which emulsification may be minimized or avoided. In fact, many companies have materially reduced their treating costs as a result of careful studies in emulsion prevention and proper handling of "wet" production. Of course, in many instances preventive measures or the correction of conditions causing emulsification cannot be achieved practically or economically, and the emulsions that form must be treated regardless of the care exercised or the money spent in attempting to prevent their formation.

Jan 1, 1939

By Hu Weibei

This paper describes the development and implementation of the control system in the flotation plants of China. The control system can be categorized as: Control in the crushing circuits: Automatic control of the flow rate of the crusher. Control in the grinding circuits: Control of the feed rate of the grinding mill and circulating load. PSM-200, an indigenous particle size monitor, and gamma-ray density gauges are utilized. Control in the flotation circuits: pH control, flotation reagent dosage estimation and control, pulp level control, aeration control, etc. Complete grinding-flotation circuits control is based on minicomputer operations. Some typical control systems which have been applied in copper flotation plants are summarized and specific problems discussed.

Jan 1, 1984

By Paul H. Rydlund

The wide use of bulk ANFO in surface coal mines is questionable in our energy conscious environment. At many locations, bulk ANFO is not the proper economic selection. Water conditions, energy requirements, waste and spillage, and vibration control are factors too often overlooked in the proper choice of blasting agents. Cost savings over 20% have been realized by converting bulk ANFO to packaged blasting agents. Future trends suggest greater concern for energy conservation in blasting will limit bulk ANFO applications and promote packaged products where quality can be maximized, waste and spillage eliminated, and water compatibility in wet areas assured.

Jan 1, 1980

By H. N. McLeod, B. C. Butler, S. R. Rice

Tius paper describes the key considerations for design of impoundments for gold mine tailings. Design options available for construction are presented. The key considerations for design of a safe, economic and environmentally sensitive design are discussed. The dam design must also balance these conventional considerations with the pragmatic aspects of construction and operations and the risk of system upsets. Case examples of tailings facilities in Canada and Papua New Guinea are discussed.

Jan 1, 1991

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran, J. Zoric

A methodology for building pragmatic physics-based models is here adapted to predict the erosion of ladle linings in the steel industry, in order to support operators when deciding whether the lining can be used safely for another heat. A defective lining may allow 140 t of molten steel to spill, with disastrous consequences for workers and plant. The adopted work flow for the development, challenges faced, and some model results are presented. One key learning outcome is that model development should allow time for maturing the process understanding, as well as for many iterations by ‘questions-responses and actions’ at various stages in the model development. Good interaction between the development team and industry case owner is an important success factor. Combining or extending the model with the use of machine learning and cognition-related methods, such as knowledge graphs and self-adaptive algorithms, is discussed.

Apr 16, 2024

DM&E PRB Project [ ] DM&E HISTORICAL MILESTONES ?Start-up in 1986 (former C&NW). ?Colony Line acquisition in 1996 (from UP). ?PRB Project Announcement in 1997 ?IC&E Acquisition in 2002 (former CP/IMRL). ?FRA Federal Refinancing in 2003 (RRIF-1).

Jan 1, 2006

By Terry M. Hertel

Zortman Mining has spent approximately three years evaluating the metallurgy of the sulfide ores from the mining area of the possible expansion project. As the test program proceeded, an interesting series of events took place which changed the scope of the work. During the agglomeration work, one of the control columns was inadvertently set up without the addition of lime to the material prior to loading and subsequent leaching. The gold recovery from this column was comparable to those columns that had a lime addition of 10 pounds per ton of ore. In fact, the gold recovery curve had a much steeper slope than those of the other columns. Furthermore, the pH of the pregnant liquor from the "no lime" column recovered to typical levels as fast as the solutions from the "lime" columns. These observations led to the concept that rinsing the ore with water prior to cyanide leaching could be advantageous to the heap-leach process.

Jan 1, 1992

There are a number a stages in a project at which an audit must, or should, be undertaken. An independent audit may be necessary for the comfort of directors and/or financiers before the major finance is committed, but an internal pre-development audit is the opportunity for the management team to take stock of the project and reaffirm their confidence and commitment. Maxims for project success are given and a check list for pre-development audits is presented. The need of mid-development audits may arise and their brief will depend on the circumstances arising. A game theory approach to decision-making is demonstrated in which the alternative of fast-tracking a development is considered. At the conclusion of the project, before the team is disbanded, a post-development audit should be made. Valuable learning can come from this process which could give important guidelines for future projects and a check list is presented.

Jan 1, 1997

Every 12 minutes, a cable operated skip car appears from beneath the desert surface of Arizona&apos;s Papago Indian Reservation. The Papagos have become quite used to the car, particularly those whose paychecks depend upon its regular appearance. The 24-ton capacity skip or tramcar hauls copper ore out of the North Decline of Hecla Mining Company&apos;s new mine about 30 mi south of Casa Grande. While there&apos;s nothing particularly glamorous about the skip itself, the railroad system upon which it travels is interesting because of the unconventional way it was built.

Jan 6, 1974

By Gungor Tuncer, Ali Kahriman, Umit Ozer, Abdul Karadogan, Mehmet Aksoy, Ertugrul Kaya, Deniz Adiguzel

This research was performed on the quarry that will be opened to produce aggregates and rock filling material at Catalagzi region at Zonguldak providence. Excavations will be done by drilling and blasting. However, there are some structures which can be adversely affected by blasting at the quarry. These structures are a methane exploration drill hole and a house at the distances of 340 m and 390 m, respectively. The one of the main goals of this study is to perform a preliminary assessment of possible damage effect of ground vibrations induced by blasting on these structures by risk analysis based on ground vibration measurements.

Jan 1, 2009

By Sandra Penttinen

To assist blasting professionals with the creation, documentation, and appropriate methodology to standardize the data collection of the pre and post blast investigation process. Penttinen Associates will present a logical non-technical presentation focusing on: Why pre-blast surveys SAVE How to prepare for pre-blast inspections What to do in preparation of pre-blast inspections The creation of an industry standard all-inclusive pre-blast document Establishing pre-blast inspection operational standards Preserving the data.

Jan 1, 2001