Search Documents

By Gerard C. Gambs

The electric utility industry is the largest customer of the U.S. coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50[c] to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag.

Jan 1, 1967

By H. Kurama

In this paper, utilization of fly ash as a value added product in areas such as novel materials, waste management, fillers and agriculture is reviewed with the aim of helping the expand of the usage of fly ash and reduce the environmental and economic impacts of disposal. The used unburned carbon benefication/treatment methods such as low temperature combustion, froth flotation, partical size classification and electrostatic separations to remove unburned carbon particles from fly ash are also discussed.

Jan 1, 2006

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft. elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 lb. pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 ½ miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in. Fig. 3.

Jan 9, 1916

By C. Legrand

THE CHAIRMAN (B. B. GOTTSBERGER, Miami, Ariz.).-I think this experience of the Burro Mountain Copper Co. with oil engines as described by Mr. Legrand comes at a very opportune time. The fuel almost universally used in the mine power plants of the Southwest is oil. Additional economy in its use for power production is much to be desired. In the case of the Miami Copper Co., we have lately found it necessary to enlarge our power plant and, based on the experience of the Burro Mountain Copper Co., we have decided to install oil engines similar to those in their plant. I think it would be very interesting to have some discussion on this subject. Mr. Langton, did you tell me you had prepared some remarks?

Jan 12, 1916

By Richard E. Barrett

The relationship between coal characteristics and power plant performance has become a matter of increasing interest to utilities. This relationship can affect the value of coals, decisions as to coal washing, setting penalties for delivery of coal that fails to meet specifications, and justifying buying better coals (at higher costs) before public utility commissions. The study described in this paper was directed to identifying how coal characteristics impact on boilers and related coal and gas handling systems. TVA data for the period 1962-1980 was the basis for the study. Models were developed for boiler efficiency, boiler availability, and maintenance costs as a function of such coal characteristics as ash, sulfur, and moisture content and boiler age. Boiler load and maintenance efforts were considered as variables in some of the models, but were found not to be statistically significant. Although the results of this study are strictly applicable to only the TVA system, they can serve as guides or first approximations for other utilities.

Jan 1, 1983

By Napier-Munn TJ

The Whiten model of crushers is currently being refined and extended at the JKMRC, with particular reference to cone crushers. This paper describes the model as a predictor of crusher power draw, discusses the application of the model, and considers the relationship between power draw and crusher performance.

Jan 1, 1988

By Niklas Willemsen

Introduction to SVCs ? SVC = Static var Compensator ? Dynamic step-less control of reactive power without switching of passive components: ? Voltage control/stabilization ? Harmonics- and flicker mitigation ? Dip mitigation ? Main components: ? TCR (Thyristor Controlled Reactor) ? Tuned harmonic filters ? Control- and cooling systems ? Typical applications: ? Mine hoists ? Large mining complexes ? EAF, SAF, rolling mills, wind/solar farms etc..

Aug 1, 2013

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By R. Hogg, D. W. Fuerstenau

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation, and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most clearly met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80% of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50% of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1973

By W. Cholewa, T. S. Golosinski, J. Wedzicha

"Power requirements of belt conveyor drives are usually estimated based on the calculated belt tension which equals the sum of unit resistances to motion which the belt has to overcome. In most situations, the value of various unit resistances can be accurately predicted using published information (5,6,8,12). A simpler approach calls for use of standard formula and tabulated values of related factors which reflect various features of both the conveyor and the transported material (2,3,7) . None of these approaches is reliable when materials with unique properties are conveyed, nor if applied to conveyors working in extreme climatic conditions. Such is the case of oil sand mines in northern Alberta.There the bitumen content of oil sand causes it to behave in a unique manner. Furthermore the conveyors operate year around, with winter temperatures often lower than - 40°C. It was the objective of presented investigations to quantify the power requirements of conveyors, and related resistance to motion for the conveyors used in oil sand mines during winter operations.The other objective was to quantify the drive power requirements of oil sand conveyors during start-up. These requirements are usually much higher than those during norm al operation, and their quantification is of paramount importance for operation of large conveyors."

Jan 1, 1992

By M. N. Brodie

The paper examines the requirements for electric power used in concentration and dewatering circuits, the effects of plant capacity and process type, the restraints imposed by the primary supply and applicable codes and outlines the procedure by which effective design is carried out.

Jan 1, 1986

The Tavua Power Proprietary Ltd. was created in 1936 for the purpose of supplying electric power, compressed air and water to the mining field.The original share capital was subscribed on a two-third:one-third basis by the Emperor Gold Mining Company Ltd. and Loloma (Fiji) Gold Mines, N.L. In 1940, Fiji Mines Development Ltd. (later changed to Dolphin Mines Ltd.) was admitted as a shareholder, and, in 1950, a further change occurred. The present shareholding in the Company is as follows:A central power station was decided upon to reticulate power and compressed air over the whole field and building commenced in May 1936.The original plant comprised three Belliss and Morcom diesel generating sets 770 b.h.p. 525 kW 3,300 V, 3 phase, 50 cycle; one Belliss and Morcom diesel compressor set 2,09'0 cu. ft. of free air per min. at 90 lb. gauge 300 r.p.m., and two small Ruston-Holman diesel compressor sets each of 525 cu. ft. capacity taken over from Loloma (Fiji) Gold Mines, N.L., and the then existing Koroere Gold Mining Company.BuildingThe original building was 130 ft. long by 47 ft. wide with an elevated switchgear annex on the west side from which a clear view of the engine room is available.

Jan 1, 1953

By A. Norholm

For grinding Portland Cement, the power consumption accounts for some 35 % of the total consumption of electrical energy for producing cement, counting right from the quarry to the packing plant. It is therefore for very good reason that great efforts during the past years have been put into making cement grinding more efficient, thereby saving power. In this paper three ways of reducing the consumption of electrical energy will be described, namely precrushing in the high pressure FLS-Köppern roller press, the introduction of a new design of COMBIDAN diaphragm in ball mills and the separation of mill discharge in the newly developed high efficient; separator SEPAX from F. L. Smidth.

Jan 1, 1987

By Adrian C. Dorenfeld

[Agitation and transport of slurries have been investigated intensively for the past twenty years. It has been shown (1) that slurries have the properties summarized in Figs. 1, 2, 3, 4, and S. For a detailed exposition the reader is referred to the above reference and the bibliography, which, in turn, have extensive references and bibliographies. An interesting problem with which the senior author has been concerned with is the scab up of power requirements for slurry agitators operating in the laminar region with pseudo plastic materials. Pulps of shaly ores, after various chemical reactions in aqueous leaching systems, are often difficult to settle and filter if agitation is violent. In these cases agitation must be at a minimum, yet prevent [tling] such as in copper uranium ores. This mild agitation is on the laminar region.]

Jan 1, 1967

By Bailey H. W

Power supply for remote mining developments is compared with supply to the general public with the conclusion that the private power plant operator has many opportunities to minimise his costs which are not open to public utilities. The main features of diesel, gas turbine and steam power plant and the limitation upon their application which may be imposed by the fuels available and the local conditions at remote sites are outlined. Reference is made to the value of joint examination by the mining engineer, metallurgist and power engineer to decide how to make best overall use of capital, labour and energy in co-ordinating the design of power and process plant and in setting no more than adequate standards of reliability and efficiency. Fluctuations in world markets make it difficult to plan mining operations to a firm time base. Suggestions are made to minimise the financial risk in forward expenditure upon power plant which in large sizes due to longer construction time may have to be ordered before a final decision is taken upon the mining development it is to serve.

Jan 1, 1973

The provision of electrical power is an important consideration in project develop- ment. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of taking a supply from a power authority or providing local generation can then be considered. This requires additional definition of the prob- able characteristics of the supply. The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was possible pre- viously. The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for a number of development projects illustrate some of the aspects which influence the decisions on power supply.

Jan 1, 1986

The provision of electrical power is an important consideration in project development. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of laking a supply from a power authority or providing local generation can then be considered. This requires additional defmition of the probable characteristics of the supply.The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was previously possible.The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for five recent Australian remote development projects indicate how some of these aspects influence the decision on power supply.

Jan 1, 1990

By Lars A. Bergstrom

High-voltage direct -current transmission is a relatively new technology. The successful development and operation of AC/DC converters, capable of handling large power blocks, have made HVDC transmission generally accepted by utility engineer s and planners around the world. HVDC technology still has significant development potential and, as a result, it is expected that equipment costs will escalate at a substantially slower rate than those of conventional AC equipment. This development will also result in still more compact terminal stations. This paper reviews two modern HVDC installations. In Zaire in Africa. a 1700-km overhead DC line rated at 500 kv, will supply power to the copper mining district in the Shaba region. Another HVDC link connects Norway and Denmark through a submarine cable rated at 250 kv. This is the longest HVDC cable in the world, 127 km, and the water depth , maximum 530 m, is also much greater than for any previous similar cable. The reasons for selecting HVDC are discussed, and the design and layouts are presented.

Jan 1, 1978

By William S. Gilmer

INTRODUCTION As man moved through the ages into the era of metals, he became increas¬ingly dependent on the extraction and beneficiation of various ore types. His progression has required more material, new sources, and inevitably, a need to extract the values from ores of much lower yield. Inherently welded to this need to extract has been the attendant requisite of power and water to carry out these tasks. With the richness of these deposits diminished, and the in¬crease of demand, mining has become so intimately tied with the needs of these auxiliary systems that the modern day milling operation can ill afford to ignore them. In the times of Agricola 16th century methods of milling required little thought for power or water consumption. Reduction was accomplished by hand¬sorting and hammer and grinding done with stamps and millstones. Medieval concentration was carried out by the "Jigging sieve" with agitation supplied by the sleeveless arm of the operator (The Mines Magazine,_ March 1933). Little consideration was likely given to the power source unless it became apparent that he had insufficient means to meet the demands of a dawn to dusk operation. Fuel for power production was also probably of little consequence unless sustained drought or warring neighbors burned the miners fields. Water was available from any adjacent stream with recycle, potable, tailings and mill consumption all going and coming from the same source. By the end of the 18th century and the early 19th century the requirements of larger throughputs and better re¬covery were forcing the miner to the need for greater sources of power and water. Arrastras, capable of accepting several hundred pounds of charge, con¬sisted of a clay bottom, a "liner of rocks harder than the substance to be crushed" and a revolving center post in which the ore was ground and amalga¬mated. Used in conjunction with a slucing system, this formed the primary recovery method of the time. Power was supplied by horse or oxen or, if terrain was amenable, by use of a horizontal or overshot water wheel. A typical system required 4.5 kw (6 hp) and needed to run in the vicinity of 15 rpm (Pre¬ston, 1895).

Jan 1, 1986

OUTSTANDING symbol of the machine age, the steam shovel needs no introduction. Few individuals there are, in the United States at least, that have not watched with fascination the almost human motion, the more than human strength, the rhythm of the whole steam-shovel cycle of crowding, digging, swinging, dumping, swinging, and crowding again. A mass of steel with some copper and other metals, fed with water and coal, guided by a single alert and dexterous operator, or perhaps two, does the work that would require 50 to 500 men or even more. The largest shovels working in the copper mines have loaded into waiting railway cars as much as 10,000 tons of ore in a single 8-hour shift. With no equipment but hand shovels, it would, in fact, be impossible to duplicate the work with any number of men; first, because they would be in each other's way, and second, because the steam shovel can lift single pieces of rock weighing 5 or 10 tons with effortless ease. Of recent years, internal-combustion engines and electric motors have displaced steam as a motive power in many instances; and of course the detailed design of the shovels has been improved immensely. Whereas the largest dippers used 30 years ago had a capacity of 3 ½ to 4 cu. yd., today the 350-ton shovel used at Chino has an 8-yd. dipper, as has the 320-ton shovel at Chuquicamata. Incidentally, for stripping at coal mines a shovel having an 18-yd. dipper is in use. However, the principle of operation of the modern shovel, regardless of the size and type of motive power, is essentially the same as that of the earlier shovels. It is fair to say that the indispensable of open-cut mining is the steam shovel, or, to be more precise, if perhaps less picturesque, the power shovel. Somehow the electric shovel seems to lack the glamour that

Jan 1, 1933