Search Documents

G. SHERBURNE ROGERS,* Washington, D. C. (written discussion?).- We are indebted to Captain Lucas for an interesting contribution to the literature of the salt-dome oil fields, and especially for his suggestion that a more aggressive method -of prospecting be adopted. The occasional discovery of new fields on, the Gulf Coast is in itself sufficient to show that the oil possibilities of the region are by no means exhausted, and those who have studied the area most thoroughly are the most optimistic regarding its future. Nevertheless, the search for new fields, according to present methods, involves the expenditure of great sums of money annually, for the proportion of dry holes to producing wells drilled yearly in the Gulf Coast region is much' greater than in most areas, even if all the wells drilled in what is commonly regarded as proved territory are included. Not only are the present methods of locating new domes very uncertain, but when a dome is discovered there is no assurance that it will be oil-bearing; or, if so, whether the oil occurs in the cap-rock, in the sands above it, or in some small isolated lens of sand far down on the flanks of the salt mass. As Captain Lucas points out, about all we positively know is that the domes are there and that some of them are oil-bearing; their origin is a matter of controversy and the original source of the oil is conjectural. Under these conditions, it is not surprising that the search for oil is conducted more or less blindly and that dry holes are common. Many wells are drilled each year in an endeavor to find oil at depths of 2000 or 3000 ft. (609 to 914 m.) or less, in locations which most geologists would condemn without hesitation. As Captain Lucas suggests, the money spent in this way might be used to far better advantage in, drilling one deep well in a carefully selected locality. Opinions may differ as to whether such a, well would find oil, and many geologists will probably believe that the chances are against it, yet all will agree that the boring, whether it finds oil or not, will probably throw light on the origin of the domes and on the source and mode of accumulation of the oil, and will therefore be of great interest, not only to the scientist, but to the oil operator.

Jan 10, 1918

By Anthony Lucas

THE discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has grown with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover, despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting, and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable

Jan 7, 1918

By S. Rajendran

The western continental margin comprises of the southwest coast (Cape Comorin-Mangalore), centralwest coast or Konkan coast (Mangalore-Bombay), northwest coast (Bombay-Gulf of Kutch) and the Laccadives area. Placer deposits of heavy minerals occur in discontinuous patches on the beaches along many parts of the west coast. The richest offshore placer deposits occur along the 25 km stretch of the southwest coast from Neendakara to Kayamkulam. The National Institute of Oceanography (NIO) surveys show that the sediments off the Konkan coast consist largely of silty sand, sandy silt and clay and the concentration of ilmenite is higher than the onshore. The heavy mineral concentration ranges up to 90% and has mainly ilmenite and magnetite with minor quantities of apatite, rutile, zircon, kyanite etc. The heavy mineral sands extend below the clays to water depth down to 20 m. The heavy minerals sands vary in thickness from 2-10 m. Offshore placers can be mined by using wire-line, bucket ladder and hydraulic dredges. Wire-line, bucket ladder and hydraulic dredges. Wire-line dredges may employ drag buckets or clamshell and hydraulic dredges suction or airlift principles. The dredges can be located on flat bottom or catamaran barges. Dredging of very near shore placers may be achieved by operating from land. The bucket ladder type of dredger has greater digging ability and hence can be deployed for mining placers which are partly consolidated or cemented or where the most valuable part of the deposit lies at the contact between the alluvium and the bedrock. This type operates very economically up to 45 m depth and needs minimum power requirement per unit dredged. Suction type hydraulic dredges can be operated very effectively up to 60 m water depths. This system is quite ideal for the inner shelf. The maximum practical economic working water depths for wire-line dredges are about 150 m. With the drag bucket modified into large net buckets, the method can be utilized to greater depths. They can be used in areas of high water currents and swells. The type of bucket can be changed readily with change in the nature of alluvium or substratum. The hydraulic suction dredge is the most suitable system for mining unconsolidated sediments. When the sediments are semi-unconsolidated, a cutter head can be mounted on the lower end of the suction pipe to agitate the seabed.

Jan 1, 1996

By C M. Zammit, N Cook, F Reith, C L. Ciobanu, J Brugger

The role of biological agents in the gold mining industry is currently limited to the use of microorganisms in bioleaching and bioremediation. However, there is a variety of possibilities in which biotechnology could aid the mining industry in the future. In this article we discuss the potential for the development of these novel biotechnologies and the role they can play in the exploration for new gold deposits, the processing of ores and the post-mining remediation of sites. The development of these biotechnologies has been enabled by rapid advances in our molecular-level understanding of the role microorganisms play in the solubilisation, dispersion and precipitation of gold. An understanding of the distribution of microbial species in soils overlying mineralisation can be utilised to develop bioindicator systems that assist with gold exploration. An in-depth knowledge of how microorganisms interact with gold complexes is being used to develop in-field biosensors, supporting exploration. Processing technologies may be improved based on advances in our understanding of the interactions between microorganisms, ore minerals, cyanide and gold. For instance, cyanide-producing microorganisms are being investigated for use in in situ leaching of gold. In turn, the use of cyanide-utilising microorganisms for the degradation of cyanide is being explored. Combined, the implementation of these biotechnologies in the gold mining sector may revolutionise the industry, leading to greener, more efficient exploration for and extraction of gold.CITATION:Zammit, C M, Cook, N, Ciobanu, C L, Brugger, J and Reith, F, 2013. Possible future applications of biotechnologies in the gold industry - a prospective approach, in Proceedings World Gold 2013 , pp 233-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By W. Everett Smith

Factors that have influenced mineralization in the Valley and Ridge and Piedmont provinces in Alabama are not clearly understood. Lithology and structure are recognizable factors in the Valley and Ridge province, where barite, lead, and zinc sulfides occur in structurally complex areas of Cambrian and Ordiovician carbonate rocks. Metal mineralization in the Piedmont province indicates a complex relationship with factors such as favorable host rock, proximity to intrusive or high-grade metamorphic rocks, several metamorphic events and separate or related structural events. Lineaments, as used herein, refer to naturally occurring linear features consisting of topographic, vegetative or soil tonal alignments that are at least partially continuous for distances greater than a mile (Lattman, 1958). Lineaments in Alabama were first recognized by J. G. Newton in 1970, using Apollo 9 series photographs. Subsequent studies delineated the features (Powell and others, 1970) and suggested relationships to structural and hydrologic factors. More recent work has explored relationships to mineralization, environmental geology and the tectonic framework of the Appalachians (Drahovzal and Copeland, 1970; Drahovzal and Neathery, in press). The lineaments recognizable on Apollo 9 photography probably represent fractures, some of which may reflect geofractures that bound major basement blocks. The lineaments defined in Alabama range from about 4 miles to nearly 200 miles in length. Most of the lineaments are straight, but some are arcuate; some appear to terminate at the intersections with other lineaments but most cross each other with no offset. Some lineaments pass through areas of structural disruption such as terminations, offsets and changes in structural style, but others show no such relationships. Most of the lineaments appear to cross topographic features with little or no obvious disruption. Orientation analyses of the lineaments divide them into three directional groupings

Jan 1, 1972

By Wetzeil N

High ambient temperatures combined with high surface humidity in the north of Australia and, in particular, the northern areas of the Northern Territory can make underground workplaces relatively inhospitable at certain times of the year. . Woodcutters' silver/lead/zinc mine, situated some 80 km south of Darwin, would be the most northerly underground operation of any significance in Australia. As such, during the build up to the wet season, it has a particular problem of ventilating a deep underground mine with already high dry and wet bulb temperatures at the surface. The Mine Management Act and Regulations mention only that workplaces shall be 'in a fit state for a person to work in or occupy'. Woodcutters therefore set in progress a Heat Stress Program to endeavour to set standards which would be more measurable and justifiable. The aim of the program was to compile a record of ambient atmospheric conditions in the working areas such that areas and/or work activities generating high ambient temperatures and humidities could be identified, quantified and qualified. Once the analysis stage of this program was completed, Woodcutters compiled a set of recommendations for the continued monitoring for, and control of, heat stress conditions to ensure that no underground employee was placed at risk from 'heat stress'. These recommendations are discussed in this paper.

Jan 1, 1994

By Stephen H. Stow

Economically important heavy minerals have been studied in the sediments of offshore Alabama and Mississippi. Sandy samples have been collected from a 200 square mile area from Dauphin to Horn Islands. The minerals concentrate in sediments under 10-35 feet of water and may reach 2.4% by weight. The distribution of total heavies is related to the hydrodynamics of offshore Alabama-Mississippi; the greatest concentrations are in the Gulf where the longshore current is diverted from its westerly flow. Preliminary observations indicate that the distribution of individual minerals can be correlated with wave energy, particle size, specific gravity, and morphology of the mineral grains. The coarser, lighter minerals--kyanite, sillimanite and staurolite--are concentrated in relatively low energy areas in the Mississippi Sound and at the end of Dauphin Island in the Gulf; maximum concentration for each is 34.5%, 6.0% and 43.2%, respectively, of the heavy minerals. The smaller, more denseminerals--ilmenite, rutile, leucoxene, zircon and monazite--are concentrated in high energy areas in the Gulf; maximum concentration for each, respectively, is 42.0%, 5.9%, 9.652, 10.7% and 1.3% of the heavy minerals. On the basis of a minimum concentration of 1% heavy minerals, two areas have been identified and the total amounts of different minerals have been calculated to a depth of 25 feet of sediment. The data are preliminary and in no way indicate recoverable reserves, but they do show that on the order of 20 million tons of heavies exist. These deposits should be termed "indicated resources".

Jan 1, 1975

The future of the United States (US) mining industry will be affected greatly by recent coal mining disasters. These have resulted in new legislation which will have an impact on mining economic costs as well safety and health of miners. This paper discusses the changes that new legislation and regulations are making to the industry and current research that is producing technologies to make mining safer and will likely impact the future of mining.

Jan 1, 2008

By R. G. Gürtunca

The future of the United States (US) mining industry will be affected greatly by recent coal mining disasters. These have resulted in new legislation which will have an impact on mining economic costs as well safety and health of miners. This paper discusses the changes that new legislation and regulations are making to the industry and current research that is producing technologies to make mining safer and will likely impact the future of mining.

Jan 1, 2009

By Jürgen Lotze

Previously (1981), it was shown that the fiscal policy practised by some IBA-member countries is mainly responsible for a significant shift of known bauxite resources into higher processing-cost categories. The possible impact of politically imposed fiscal costs on the competitiveness of relevant bauxite resources is investigated in detail by means of a model calculation procedure.

Jan 1, 1984

By E. J. Magri, D. M. Hawkins

This paper deals with an experimental programme carried out with a gold analyser in the period June to September 1979 at Loraine Gold Mines. The results were found to be reproducible, with no overall or conditional bias when the measurements were compared with those obtained from chip samples. The standard error of estimation of a 3 m reef exposure, which was the sampling interval, can be reduced by a factor of 2,5 if the complete stretch is scanned, rather than the taking of one chip sample in its centre. Complete statistical and computational procedures were developed for the fitting of the normal-Iognormal model to observed analyser data and for the determination of the most likely gold grade for a particular analyser measurement. (This corection procedure is necessary since a significant number of negative analyser measurements can be observed.) Panel averages of uncorrected scans showed a small conditional bias relative to those of corrected scans. However, uncorrected panel averages can be used for on-the-spot decisions regarding whole panels. For standard calculations of ore reserves, use should be made of corrected scans. Under reasonable assumptions, the use of the detector in the selective mining of low-grade narrow reefs such as the Basal Reef at Loraine Gold Mines, when compared with the conventional chip-sampling method, can result in a saving of as high as R40 million in present-money terms over the life of a project. The difference could be even larger in a highly variable reef like the B Reef at Loraine Gold Mines.

Jan 1, 1987

By R Lau

The fire safety design for road tunnels includes the following aspects: active systems, passive provisions and operational procedures. The active systems include the smoke control system, fire suppression system, detection system and fire fighter’s assistance systems. Passive provisions include escape passages, fire separation and fire resistance systems. The operational procedures refer to fire fighter access, reporting and alerts, evacuation processes and crowd control.Currently, these systems are typically designed by different designers or teams. These systems are intended to work together in a coordinated manner to provide the desired safety outcome. However, in practice, this is not always happening. The fire engineering process is supposed to bring together all these aspects and arrive at an integrated safety system. The fi re engineering process in practice is not integrating the design with the practice or reality and is thus arriving at less than desirably efficient safety systems.The example of design inputs shows how disconnected each system design basis is. The smoke control system design is based on the design fire size. The performance of the smoke control system is to achieve a smoke free environment for a defined space for a particular fire size – the design fire. The fire suppression system – most commonly sprinklers or deluge systems, is designed according to codes and to achieve a certain water discharge rate. The fire detection system is designed to detect temperature rise/rate of rise and perhaps density of smoke. Fire separation is determined to provide a certain period of service – mostly for structural elements. Escape route size and location is determined mostly by code compliance. Evacuation procedures are determined by Authority operational requirements rather than human behaviour.To arrive at an integrated fire safety system, the design basis and performances must be coordinated. An approach using fire scenarios would ensure all systems are designed to a common performance requirement. This paper will discuss how the current design approach outcomes compared with a fire scenario approach. More effective and efficient fire safety systems would require the stake holders to understand the implication of this approach and to embrace this through the fire engineering process.

Mar 8, 2011

By D. Krawczykowski, D. Saramak, T. Gawenda

"Annual world zinc consumption is as high as nearly 14 millions of tonnes. Approximately 50% share of zinc is used for corrosion protection in processes of continuous galvanization and the hot dip processes. In the latter, two zinc containing residues are produced: zinc ash and hard zinc, which constitute around 10% each. Paper concerns the method of possible separation of metallic zinc from the non-metallic zinc compounds from the zinc ashes – the waste product of hot dip galvanization process. The investigative programme covered the comminution tests of the feed (zinc ash) in selected crushers: jaw crusher, roller crusher and impactor. Results of investigations show that application of individual crushing device results in various breakage of the feed sample. Impact force caused the highest increase in finest particles size fractions of the product, while metallic and non-metallic fractions were comminuted differently. The compression force, in turn, caused the selective comminution, i.e. the breakage of metallic zinc was observed in a higher degree. The presented approach appears to be an economical supplementary method of initial recovery of metallic zinc from metallurgical zinc waste. For the high demands for the zinc in the world and the need of corrosion protection, the method presented in the paper helps in more effective zinc recovery and environmental protection.INTRODUCTION AND METHODOLOGY World production of metallic zinc during last decade shows a slight increase and in recent years its consumptions reach 14 millions of tonnes. Figure 1 shows world production of zinc in the time period 2009 – 2016. Main directions of zinc utilization include: - Galvanization - Production of zinc alloys - Brass and bronze production - Semi-manufactures of zinc - Chemicals The major share in global zinc consumption constitute galvanization process (Bright 2007). Two main types of zinc galvanization are: hot-dip galvanizing (HDG) and electro-galvanizing."

Jan 1, 2018

By J. M. Harrison

FIELD PARTIES of the Geological Survey of Canada have, in recent years, mapped several areas east and northeast of Flin Flon (9, 10, 12, 13, 14, 15, 118) (1). In all these areas the mineral deposits show a close geographical relation to faults although the immediate control of most of the known ore deposits appears to be folded structures in the rocks (8, 11, 18, 19). Air photographs and published geological maps were studied in order to ascertain whether or not the mineral deposits in the Flin Flon-Snow Lake mineral belt as a whole show any spatial relationship to faults. It was found that most of them do show a distinct geographical association with faults, or with topographic features that may be faults. It is further apparent on air photographs that a major lineament, for composite of lineaments, follows approximately the contact between gneisses and schists of the Kisseynew complex on the north, and Amisk volcanic rocks on the south. However, this Kisseynew lineament is not continuous and, especially in the eastern half of the district, it is exceedingly irregular in plan. Parts of this lineament have been mapped as faults (9, 10, 12, 14), other parts have been shown as stratigraphic contacts (1, 2, 21, 27), and still other parts have not been studied except by reconnaissance methods. It is suggested that the Kisseynew lineament may be due to a deformed fault that extends easterly from a point about 25 miles west-northwest of Flin Flon to a point at least 10 miles northeast of Wekusko lake and that the mineral deposits.

Jan 1, 1951

By Anthony Iannacchione, Christopher Mark

Residents of Maxwell Hill, a suburb of Beckley, West Virginia, reported from January until March of 1988 a series of earth tremors. The tremors rattled dishes, and the noises associated with tremors were sometimes loud enough to wake people at night. These events were puzzling because Beckley is in an area of low seismic activity. Maxwell Hill is located above abandoned coal mines, though no direct subsidence damage to surface structures has been documented. A research program was initiated to determine whether subsurface ground movements associated with the abandoned mines could be responsible for the seismic activity experienced at the surface. A hypothesis is proposed which states that seismic disturbances can be caused by abandoned mine failure when two conditions are met. First, some instability must exist at the mine level. The most likely cause of instability is the failure of pillars of coal that were left for support at the time of mining. Second, subsurface movements can result in significant seismic activity only when the rock above the mine contains at least one very strong and brittle layer that is prone to fail violently through rupture or fault slip movement. Analysis of the data indicates that both hypothesized conditions for mine-related seismicity appear to have been satisfied in the case of Maxwell Hill. It has therefore been concluded that the earth tremors experienced by Maxwell Hill residents probably are related to the abandoned mines. Analysis of the potential magnitude of these events indicates that they are unlikely to cause significant surface danlage. The probability that future events will disturb the residence of Maxwell Hill should be quite low based on the identified mechanism.

Solid. dense, air-cooled slag can fulfil most, if not all, the functions of natural stone for civil engineering purposes. The value of pumice, also, has long been appreciated, and processes for the manufacture of similar synthetic material for light-weight concretes and insulating fills have been developed in past years.Foamed slag is, in effect, blast furnace pumice and is often referred to on the European continent as metallurgical pumice. It is made by the treatment of molten blast furnace slags with a critical quantity of water during which process the slag cools and expands into a sponge-like mass. The connection between foamed slag and air-cooled slag is also considered and a basis for density control given.All blast furnace slag cannot be foamed to give a product which would comply with B.S.S.877; 1939 Foamed Blast Furnace Slag. A large proportion of the total output of molten slag lacks the necessary inherent properties. This investigation attempts to discover the conditions necessary for the production of foamed slag capable of meeting the British specification.EARLIER WORKIt was generally accepted (Parker, 1951; Gallai-Hatchard, 1955) that the spongy structure of foamed slag was caused mechanically by steam trapped in the slag when it was poured into water. It was assumed that slags which would not foam would not trap steam, because their viscosities and surface tensions were unsatisfactory, on account of temperature and/or composition. The earliest systematic investigation was made by Frisak (1923) who attempted to establish a limiting chemical composition for foamable slags. He decided that foamable slags covered most blast furnace slag compositions on the basis of silica, alumina, and lime, and further "that the replacement of lime by magnesia up to 15 per cent has no noteworthy effect on foamability, that moderate quantities of alkalis are not deleterious, that sulphur raises the foamability and that MnO is only deleterious in the presence of 1...

Jan 1, 1963

The epizonal Ag-Pb-Zn vein deposit at San Bartolome is characterised by a base-metal sulphide assemblage containing the spectacular development of interpenetrating, bladed networks of pyrrhotite which have been replaced by marcasite and pyrite. A similar assemblage displaying the same crystal habits and textures are also a diagnostic feature of the Sn and SnAg deposits ofBolivia. On this basis, it is reasonable to conclude that both deposits were formed from fluids of similar nature and origin. Although no economic accumulation of Sn is known in San Bartolome, further comparison of the geologic setting, age, mineralogy, fluid inclusion data and magmatic association of this deposit with the Bolivian systems has highlighted additional similarities consistent with a hypothesis that more extensive Sn mineralisation might exist in the San Bartolome area.

Jan 1, 1995

The epizonal Ag-Pb-Zn vein deposit at San Bartolome is characterised by a base-metal sulphide assemblage containing the spectacular development of interpenetrating, bladed networks of pyrrhotite which have been replaced by marcasite and pyrite. A similar assemblage displaying the same crystal habits and textures are also a diagnostic feature of the Sn and Sn- Ag deposits of Bolivia. On this basis, it is reasonable to conclude that both deposits were formed from fluids of similar nature and origin. Although no economic accumulation of Sn is known in San Bartolomr, further comparison of the geologic setting, age, mineralogy, fluid inclusion data and magmatic association of this deposit with the Bolivian systems has highlighted additional similarities consistent with a hypothesis that more extensive Sn mineralisation might exist in the San Bartolomd area.

Jan 1, 1995

By A. Galibois, A. Dubé, H. Monette, J. L. Collins

"The start of mining operations often raises serious financial problems. In marginal cases promoters frequently demand financial aid from governments.In the past, the financial assistance has taken the form of gifts, procurement contracts, etc., but aid in such form has been severely criticized. A new formula has been developed to provide a more equitable distribution of the revenues accruing to the government and to private capital.The benefits to these two parties have been evaluated in an hypothetical case and compared in terms of internal rates of return on their investment, their shares of the undiscounted cash flows and their primary profits.The method based on the non-zero sum game theory provides a means for suggesting the lowest feasible annual production and the optimal sum contributed by the government in the form of outright gift, equity capital and convertible bonds. Other financial hypotheses can also be optimized by the computerized analysis."

Jan 1, 2014

By George W. Pawel

OWING largely to its value as a toughener and strengthener of steel for both industrial and military purposes, nickel is playing, an important role in the current war. It is fine of the metals in which the Allies enjoy a definite edge over the Axis nations and this time there is no place to which the Germans may send another submarine "Deutsehland" and expect to pick up a cargo of nickel to replenish their exhausted supplies. Total world nickel production thanks almost entirely to the expanded operation of the International Nickel Co. of Canada at Sudbury must now be at the rate of around 175,000 tons a year scarcely more than 5 per cent of which is accounted for by Germany, Italy and Japan. This represents more than four times the world output at the end of the first World War.

Jan 1, 1943