Search Documents

Pilot plant work has played a major role in the process development and design phase of the Iscor Heavy Minerals project. The pilot plant campaigns have been aimed at three process areas, namely primary beneficiation (wet gravity circuits), heavy mineral separation and ilmenite smelting. A process development structure was put in place, and the various pilot plants designed and built. A number of pilot campaigns were conducted during the project phase since 1995, and most of the key objectives were achieved. Various other valuable ælessonsÆ were learnt, and were incorporated in the full-scale plant designs, or used to change operating philosophies, equipment choices et cetera. The cost and durations of the pilot runs were significant, and an analysis indicated that the major risk and technology area of smelting has contributed more than 70 per cent of the total cost.

Jan 1, 2001

By Smith T. N, Wild M. B, Elliot B. J

The process of flash smelting of nickel sulphide ores, as practised at the Kalgoorlie Nickel Smelter, is described. The critical variables in the operation of this process are identified. The design of a pilot-scale, turbulent-jet flash reactor which models the essential features of the industrial smelter is described. A report of its operation and application to an investigation of the ignition of particles of sulphide species is given.

Jan 1, 1991

A pilot plant has been constructed for the low temperature carboni-zation of Wallarah (N,S,W6) coal at the rate of 300 pounds per hour. The plant was built and tested at Australian Mineral Development Laboratories for Broken Hill Pty, Ltd. Char product was required within the specifi-cation 15.5 `S' 1 per cent volatile matter. The design was based c atz an entrained state carbonizer developed by Parry and U.S. Bureau of Mines co-workers at Denver, U.S.A. The method involved the carbonizatioan of fine coal by entrainment with air in an externally heated reactor.. The heat required for carbonization of tits coal was supplied to the be, both through the reactor walls and also by internal cambustion of products .

Jan 1, 1963

A pilot plant was constructed for the low temperature carbonization of Wallarah (N.S.W.) coal at the rate of 300 lb/hr. The design was based on an entrained state carbonizer developed by Parry and D.S. Bureau of Mines co-workers. Prior to delivery to the client, the plant was successfully operated over periods of several days duration.INTRODUCTIONIn September 1961, the Australian Mineral Development Laboratories (A.M.D.L.) was engaged by the Broken Hill Pty. Co. Ltd. (B.H.P.) to design, construct and test an entrained state coal carbonizer with a capacity of 300 lb/hr of Wallarah (N.S.W.) coal. Char product was required within the specification 15·5 -I- 1 per cent volatile matter. The design was to be based on a pilot plant developed by Parry and others in the D.S. Bureau of Mines Coal Research Laboratory at Denver, D.S.A. The method involved the carbonization of fine coal by entrainment with air in an externally heated reactor. The heat required for the carbonization of the coal was to be supplied to the bed both through the reactor walls, and also by internal combustion of products in the bed. Several D.S. Bureau of Mines Reports of Investigations weFe used as the main guide to the physical layout and proportions of the plant. However, the individual units required detailed designing, before engineering drawings could be prepared and fabrication begun.A 10 ton sample of crushed Wallarah coal was used for preliminary testing of the plant. The first test run on the pilot plant was carried out in February, 1962. After some modification a second test of longer duration was conducted in August, 1962. These operations aimed at running in the plant and also at determining the operating temperature to produce specification char and the maximum capacity of the...

Jan 1, 1963

By D. P. Tao, J. G. Groppo, R. Killmeyer, W. W. Wen, B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 ~ 25 m) clean coal slurry produced by the `Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 165o cake formation angle, provided a filter cake with 23.6percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of `orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 -25 m) clean coal slurry produced by the 'Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 1650 cake formation angle, provided a filter cake with 23.6 percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only 65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23 percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8 percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of 'orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Mark E. Smith

To allow recovery of gold values from ore which cannot be economically processed by the mill, Pinson Mining Company has developed a run-of-mine heap leaching facility. In order to estimate production scale recovery rates, reagent consumption and percolation problems, a series of pilot scale tests were performed. These tests typically consisted of 3,630 metric tons (mt) (4,000 tons) leach ore at a grade of .94 to 1.56 grams Au per metric ton (g/mt) (.03 to .05 oz. Au/ton). Test heaps were loader stacked to approximately 4.3 meters (14 feet) high. Information from these pilot scale tests was employed in the design and construction of the production scale facility. Parameters such as spray rate, leach cycle, sprinkler placement, and barren solution chemistry were determined by the pilot tests.

Jan 1, 1984

By Mark E. Smith

To allow recovery of gold values from ore which cannot be economically processed by the mill, Pinson Mining Company has developed a run-of-mine heap leaching facility. In order to estimate production scale recovery rates, reagent consumption and percolation problems, a series of pilot scale tests were performed. These tests typically consisted of 3,630 metric tons (mt) (4,000 tons) leach ore at a grade of .94 to 1.56 grams per metric ton (g/mt) (.03 to .05 oz.) Au/Ton. Test heaps were loader stacked to approximately 4.3 meters (14 feet) high. Information from these pilot scale tests was employed in the design and construction of the production scale facility. Parameters such as spray rate, leach cycle, sprinkler placement, and barren solution chemistry were determined by the pilot tests.

Jan 1, 1983

By Nils Eivind Kamfjord, Halvard Tveit, Ingeborg Solheim

"Because of its negative environmental effect the attention towards NO emissions increases. This again leads to new demands from the authorities for better surveillance and control of emissions. Earlier and recent industrial measurements towards FeSi- and Si-metal furnaces reveal quite high NO-emission. The NO is believed to be produced in the combustion zone above the furnace surface, mainly as thermal NO.In order to expand the knowledge on NO-formation in silicon metal production, a pilot scale experiment in a 440 kVA silicon furnace has been carried out. The experimental set-up was designed with a view to be able to copy and manipulate the formation mechanisms for NO by controlling the flow of false air into the off-gas system.The resulting NO-values corresponding to the different air inlet to the furnace top, show significantly differences between the different air inlet geometries.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2). Since combustion of fuels, such as gasoline, diesel, bio diesel, propane, coal, and ethanol, forms NOx the dominating contributors to NOx emissions are the on-/offshore transportation industry and power generation based on fossil fuels [1]."

Jan 1, 2012

In an earlier paper(l) details of a laboratory method of extracting and separating tantalum and columbium oxides from tantalite have been given. In view of the fact that Australia may have need to be self sufficient in this field it was decided to erect a pilot plant for the production of tantalum oxide in the Metallurgy School, University of Melbourne. The plant was designed for treating about 40 lb. of ore in a batch over a period of two weeks, although; because of the sectionalized nature of the process, the capacity of the plant was 40 lb. ore per week.Australia is fortunate in possessing some very rich tantalite and columbite deposits, particularly in the Pilbara District in Western Australia. The ore used in this work was obtained from a small but high grade deposit near Greenbushes, Western Australia, and consisted of lumps, weighing up to 8 lb. each, of almost pure ferro-tantalite with occasional thin veins of the very' rare' mineral stibiotantalite.The main constituents were:

Jan 1, 1946

By C. Wieckert

Concentrated solar energy can be used as heat source for the production of metals. One of the most promising respective processes, the solar carbothermic production of Zn from ZnO, is investigated within the European research project SOLZINC, a cooperation of institutes and industries from France, Germany, Israel, Sweden and Switzerland. The solar produced Zn can be used as commodity or as an energy carrier for further processing on demand to electricity in Zn-air fuel cells/batteries or to generate hydrogen by reaction with steam. In both cases the Zn is oxidized to form ZnO, which can be recycled back to the solar plant. In these cyclic processes Zn acts as a means to store and eventually transport solar energy. Second product of the solar process step is a CO-rich offgas, which may e.g. drive a gas engine or may be shifted to hydrogen in a conventional reaction with steam. A pilot plant using 300kW concentrated solar power input has been constructed and operated successfully. 86mass-% of ZnO mixed with 14mass-% of charcoal are reacted to produce Zn and CO at a temperature of about 1200°C, yielding about 50 kg gaseous Zn per hour. Zn-dust with 95% purity is recovered from the offgas system that was designed to produce Zn for Zn-air fuel cells. Based on the results and findings from the pilot plant, a two tons Zn/h solar demonstration plant has been designed conceptually. Cost studies have been performed and scenarios for producing electricity or H2 via these ZnO/Zn-cyclic processes are evaluated.

Jan 1, 2006

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By PDF

Previous work has shown that significant, free milling gold values exist in the Ryan Lode ore. This project used pilot scale equipment to estimate the percentage of gold recoverable by gravity methods from the circulating load of a conventional, closed-circuit, grinding mill. The pilot scale flowsheet employed three stages of gravity concentration, hydraulic classification and batch grinding to simulate a full scale milling circuit. 172 kg (379 lbs) of Ryan Lode ore were processed, having a head grade of 4.8 g/metric ton (0.14 oz/ton). Results showed that simple gravity methods are capable of recovering 45-50% of the gold values in a concentrate grading in excess of 3430 g/metric ton (100 oz/ton). Of the remaining gold values reporting to the classifier overflow solids (80% passing 70 microns, 3.1 g/metric ton (0.09 oz/ton)) 89% were recovered from 48 hour bottle roll tests.

Jan 1, 1995

By Jeffiey B. Austin, Maurice Tagami

"The ores of the Iberian Pynte Belt are typically massive sulphide ores with very fine grained mineral textures. EuroZinc Mining Corporation is currently evaluating one of the massive sulphide deposits located near the town of Aljustrel, in South Central Portugal. The deposit contains significant grades of lead, zinc and silver. The ores are comprised solely of sulphide mineralization consisting of pyrite, sphalerite, galena and some secondary copper minerals. Liberation requirements for these ores are typically 22 to 25 microns. A selective flotation process has been utilized to produce separate lead and zinc concentrates for sale to off-site contract smelters.This paper outlines the process test results and describes the process parameters required to optimize the process parameters. Ths test program has been conducted in support of the re-opening of the facilities in Aljustrel. The 3500 tpd mining and milling facility was commissioned in 1990 and operated for 18 months before closing. The previous facility was designed to produce three products using a selective copper-lead-zinc flotation process. EuroZinc Mining Corporation is proposing to re-open the operation, selectively mining from a lead-zinc phase of the massive sulphide deposit and produce only lead and zinc concentrates.Results are presented and discussed.PROJECT HISTORY AND CURRENT PROJECT OBJECTIVESThe EuroZinc Aljustrel Project is a potential major producer of lead, zinc and silver located in the Iberian Pyrite belt of south-central Portugal. The town of Aljustrel is historically associated with mining dating to the time of the Romans. The area is rich in pyrite deposits, and sections of the pyrite deposits contain significant zones of copper, lead, zinc and silver. Mining in Aljustrel during the last century (1900’s) included a major pyrite mining operation, which produced feed for sulphuric acid production. Pynte mining operated from the 1930’s to the early 1970’s and a short-lived base metal operation from 1989 to 199 1."

Jan 1, 2000

The pilot scale testing of Australian coals for their NO, emissions was carried out at the ACTC to investigate the influence of coal properties, furnace conditions and different NO,, control strategies on NO,, emissions. The NOx emissions for the Australian coals tested were found to vary over a wide range and primarily depended on combustion temperature and excess oxygen conditions. These coals did not exhibit any fundamental difference in NOx levels to other world coals. Under similar combustion conditions, the conversion of coal nitrogen to NO. was found to be best correlated with coal rank parameter, R, max per centage. The use of staged combustion as a control strategy was shown to reduce their NOx levels by 56 - 77 per cent.

Jan 1, 1991

By J. G. Groppo

The Andritz Ruthner Inc. hyperbaric filter was evaluated at a pilot scale for dewatering fine coal cleaned by froth flotation. The pilot scale dewatering testing was conducted at a solid feed rate ranging from 100 lbs to 200 lbs/hr-ft2. Effect of hyperbaric operating parameters and addition of various surfactants and flocculants were evaluated on dewatering of fine coal. The tests data indicated that for the minus 100 mesh and minus 28 mesh clean coal product, the Andritz hyperbaric unit provided filter cake containing 23 percent and 14 percent moisture, respectively.

Jan 1, 1996

By M. Muinonen, A. R. Barnes, R. Pandher, M. J. Lavigne

Over the past three years, Ring of Fire chromite ores have been tested extensively at both the bench scale and pilot scale at XPS Consulting and Testwork Services. Following bench scale testwork, two smelting campaigns were completed using a 300 kW DC arc furnace on different chromite deposits from the Ring of Fire. A ChemSheet model was developed to aid in the design and optimization of the recipes, and its predictions were confirmed with both the bench scale and pilot scale tests. A total of 7.5 tonnes of chromite ore was smelted at XPS. The results of the testwork demonstrate excellent reducibility for the ores tested with good reduction kinetics when compared with South African chromites.

Jan 1, 2014

By M Miller

Operators of nickel laterite pressure acid leach and gold pressure oxidation technology frequently employ a series of steam condensing heaters to preheat the leach feed slurry. The heaters are an economic pinch point û although the thermal performance of the heaters is critical to overall process viability and operating cost minimisation, they are also a significant capital item and must be sized accordingly. Despite this, discussions of the factors underlying heater design are conspicuously absent from technical literature, and existing operations feature a conflicting range of heater sizes and configurations. This variety would suggest that at least some of the chosen heater designs are oversized. As part of its detailed design stage, the Ravensthorpe Nickel Project (RNP) constructed and tested a pilot plant heater to develop an understanding of the heating process and to ensure that the RNP heaters were appropriately sized. This testwork used RNP slurry at design density and viscosity on a 450 mm diameter, 6500 mm high column. The pilot plant testwork demonstrated the intrinsic efficiency of the direct steam condensation heating process, which was essentially independent of slurry density and viscosity. Presence of non-condensable gases in the steam phase decreased the heat transferred in certain circumstances, but heater performance remained consistent with thermodynamic limitations. Stagewise heat transfer within the column was rapid, and suggested either a very high slurry surface area or excellent heat transfer within the slurry phase. While the testwork did not set out to distinguish between these effects, physical evidence pointed to droplet formation in the inter-tray shower zone, giving a high heat transfer area. For scale-up purposes, the key facts were that the heat transfer rate was not limited by using high viscosity slurries and heaters could be designed using the principles applied to the smaller of those in existing operations. This paper discusses existing slurry heater designs, the current understanding from open literature, the pilot plant testwork, results and analysis, and scale-up to commercial sized equipment.

Jan 1, 2005

By F Mwijage

"The benefits of measuring blast movement to reduce ore loss and dilution have been recognised by many people for many years and various methods have been used with limited success. Geita Gold Mine is running the pilot study on the blast movement monitoring (BMM) system which is a revolutionary method developed and patented by the University of Queensland and Blast Movement Technology (BMT). The system consists of directional transmitters placed within the shot prior to blasting, which are then located after the blast with a special detector and then the data is processed with purpose-designed software.As part of continuous improvement on grade control, Geita Gold Mine is running a research project in all operating pits with the objective of: quantifying the three-dimensional blast muck pile movement and finally utilise the movement data to define post-blast ore polygons and incorporate the movement dynamics during block modelling,quantify the potential savings for ore loss and dilution,improve mine geologists knowledge of blast dynamics, andstimulate greater co-operation between drill and blast engineers and geologists to achieve optimum blast designs.To any operation with selective mining, it is critical to the economics of an operation to control ore loss and dilution; getting it wrong will result in significant lost revenue. Implementation of ongoing pilot study on electronic balls as determinant on blast movement dynamics on ore would be of longer term solution and big investment pay back.CITATION:Mwijage, F, 2012. Pilot study on blast movement monitoring at Geita gold mine, in Proceedings Narrow Vein Mining 2012 , pp 49-58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By D. Jacobson

There are many different machine setup parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the eccentric speed at which the cone gyrates. In June 2012, pilot tests were conducted on a 200 hp high speed cone crusher to determine the production and operating conditions over a wide spectrum of eccentric speed. Every plant will have variations in the ore characteristics and feed rates throughout the life of the mine, and at times throughout a single shift of operation, which result in non-optimal use of the crushing energy and inconsistent process control. For high speed cone crushers, the crusher will exhibit a different capacity, power required, and discharge size distribution as the speed ranges over the design limits of the machine. This study documents the measured variation in production and energy efficiency both when the crusher was ran at full capacity as well as when the feed to the crusher was not sufficient to run at full capacity. Overall, the results match theory and the capacity and power fluctuated by 25% and 17%, respectively, over the speed range when operated full while there was an overall trend of slightly coarser discharge size distribution as the speed decreased. The results with the fixed feed rate were more telling, as the crushers had 4-14% higher production when making a theoretical minus 12.5 mm product when operating at the optimal speed as compared to the worst speed in the ?typical? speed range for this application. Secondary analysis of the fixed tonnage testing also showed that the power draw was more consistent with lower magnitude spikes at the higher speeds (higher cavity level), as on average the standard deviation of the power draw increased from 7% to 18% and the peak power spikes from 20% to 48% over the speed range tested. The findings lay groundwork for more efficient plant design. Varying the speed of the crusher can be used to tune the crusher speed during commissioning, adapt to changing ore conditions over long periods of time, or be used as a dynamic input into an advanced control system. Each action above would serve to make the crusher(s) more productive and more energy efficient, and would also have mechanical benefits for the machine. Key Words: cone crusher, ore reduction, process control, crushing efficiency

Feb 27, 2013