Search Documents

By R. J. Fruehan

The oxygen activity and concentration were measured in Fe-Cr-0 melts in equilibrium with an oxide phase at 1600°C (2912°F). The activity was determined by ,use of the following solid oxide -electrolyte galvanic cell CY-Cr8,(s) I ZrOz(CaO) I Fe-CY-G(saturated)(l) The oxygen concentration decreases with increasing Cr concentration to about 270 ppm 0 at about 7pct CY and then increases gradually. The activity coefficient of oxygen (fo) decreases with increasing Cr. In melts containing up to about 20 pct Cr, log f is approximately a linear function of wt pct Cr with a slope (e q 2) of —0.037. The activity of chromium was calculated and found to exhibit a small negative deviation from Raoult's law. From the activity and solubility data for low chromium melts, the free energy of formation of chromite, FeCr204, was found to be -79.8kcal per mole where pure liquid chromium and oxygen at I wt pct in Fe are the standard states. ThE effect of chromium on the chemical behavior of dissolved oxygen in liquid iron is of great importance in controlling the deoxidation of steels containing a significant amount of chromium. Chen and chipman' equilibrated Fe-Cr melts in the presence and absence of slag with hydrogen-water vapor mixtures. They concluded that at 1595°C chromite was the oxide phase in equilibrium with Fe-Cr alloys containing less than 5.5 pct Cr while at higher chromium concentration Cr,O, was the stable phase. In the composition range 0 to 10 pct Cr they found that the interaction coefficient, was equal to -0.041. Turk-dogan,' Schenck and Steinmetz,, and pargeter4 measured egr) in a similar manner and found the value to be -0.064,-0.04, and -0.052, respectively. McLean and Be11 evaluated egr) from their data on the equilibrium of Fe-Cr-Al-0 alloys with H2/H20 mixtures and found it to be -0.058. However, McLean and Bell's value should only be considered an estimate because the effect of aluminum on the activity coefficient of oxygen is about a hundred times greater than that of chromium. Consequently, an error in the value of egl) used, which at the present time is not well-known, or an error in aluminum analysis, which is present in very small quantities, will result in a significant error in egr). Fischer et a1.6 determined the interaction coefficient (eEr) in Fe-Cr-0 melts not in equilibrium with an oxide phase and containing less than 18 wt pct Cr at 1600°C electrochemically. They determined a value of -0.031 for egr). Hilty et aL7 measured the oxygen content of Fe-Cr melts in equilibrium with an oxide phase containing up to 50 pct Cr. They found that the solubility of oxygen decreased as the chromium content increased to about 6 pct Cr and then increased gradually. They concluded that the equilibrium oxide phase was chromite below 3 pct Cr, distorted spinel from 3 to 9 pct Cr, and Cr,04 above 9 pct Cr. Adachi and lwamotoa also investigated this system, but did not find Cr30,. They X-rayed the equilibrium oxide phases and did not find the presence of Cr,O,. They also X-rayed the oxide phase extracted from a 65 pct Cr melt which was heat treated and did not find metallic chromium as would be expected if Cr3O4 were the equilibrium oxide phase as indicated by the reaction : 3Cr3O4 — 4Cr2O:, + Cr [lj It was the purpose of the present investigation to determine the effect of chromium on the activity coefficient of oxygen in Fe-Cr melts by measuring the activity and solubility of oxygen equilibrated with an oxide phase in the composition range 0.18 to 50.5 wt pct Cr at 1600°C (2912°F). The activity of oxygen in the melts was determined by use of the following galvanic cell: The relationship between the partial pressure of oxygen in equilibrium with the melt and the reversible electromotive force of the cell (E) is where 11 = 4, F is the Faraday constant, pb, is the oxygen pressure in equilibrium with the meit and is the oxygen pressure in equilibrium with Cr203 as determined from the free energy data compiled by Elliott et al? The oxide phase in equilibrium with pure chromium was assumed to be Cr If Cr30, were the equilibrium phase the activities derived would be approximately the same, since the best estimated free energy of formation of Cr,O,, if it does exist, is approximately % the free energy of formation of The activity of chromium in Fe-Cr alloys at 1600° C was also determined from the measured electromotive force. The activity of chromium (aCr) is related to the electromotive force as follows: , The oxide phase in equilibrium with pure chromium and Fe-Cr melts from 10 to 52 pct is assumed to be Cr203 so that n equals three. If future work proves the existence of Crs04 in equilibrium with Fe-Cr melts and pure chromium, the experimental results can be reevaluated using a value of $ for n in Eq. 141. A value of ^ for n will make the activities about 10 pct higher. In order for Eqs. 131 and [4J to be valid the electrolyte, ZrOa(CaO), must exhibit predominantly ionic conduction at the temperature and oxygen partial pressure of its use. Previous work1' has demonstrated that ZrOz(Ca0) is predonlinantly an ionic conductor

Jan 1, 1970

By Shiro Ban-ya, John F. Elliott, John Chipman

The activity of carbon in Fe-C austenite at 1150°C has been determined for concentrations up to about 2.1 pct C using the equilibrium: C + COz = 2CO; equations have been derived expessing the activity as a function of carbon content on the basis of twelve mathematical models. Several of these represent the data satisfactorily. ACCURATE information on the thermodynamic properties of austenite in the binary system Fe-C is needed as a basis for studies of transformation and precipitation in steels of all sorts, alloy as well as plain carbon. The many attempts to approach this problem through statistical thermodynamics require sound and dependable experimental data in order to evaluate the several models which have been suggested. In this paper we are concerned with the experimental determination of the activity-composition relation in austenite at the temperature of its widest range of stability, approximately the eutectic temperature (1153°C). Accurate investigation of the activity of carbon in austenite may be said to have begun with the work of Dunwald and wagner.' A more detailed study was carried out by R. P. smith2 on the two equilibria: More recent work on these two equilibria has been reviewed by Chipman,3 who pointed out the experimental hazards associated with studies of Eq. [I]. Studies of this reaction involve rather small values of the ratio these are susceptible to errors due to traces of moisture in the apparatus according to the reaction: Ellis, Davidson, and Bodsworth4 evaluated K, for their experimental temperatures and used desiccants to control water vapor pressure. While they were able in this way to obtain consistent values for K1 it cannot be said that all of the uncertainties of the method have been overcome. Results by both methods reported by Schurmann, Schmidt, and wagener5 appear to be consistent except at very low carbon content. Reaction [2] was employed in the experimental work reported here. It is to be recognized, however, that it is not applicable to projected studies of certain alloy steel compositions involving stable oxide-formers.

Jan 1, 1970

By C. S. Samis, J. C. Mitchell

Sodion activity data have been obtained for the Na-A1 system for sodium concentrations in aluminum between NN, = 25 . 10-and 300 x 10'. This concentration intert-a2 encompasses those sodium concentrations nor1)zally encountered in aluminum reduction cell operation. The sodium activity data were measured by a two-phase equilibration of sodium between a lead and an aluminam rich phase. The Na-Pb system was emplojed as a reference for the determination of the actiz7itj 0.f sodium. The activity of sodiin in aluminuwz exhibits large positi2.e deviations frorn ideality and a strong dependence, on concentration below NN, = 100 x 1K6. The inteated data indicate that the activity of aluminium is equal to its mole fraction over the range of miscibility of the Na-A1 sgstem. The data on the Na-A1 binary have been combined with experimental data on the cryolite-A1 system at 1025°C to obtain the activities of Na F and AlF, in liquid cryolite oz2er the cornposition 1-ange encountered in aluminum cell operation. The results are in agreement with activities calculated from the NaF-AlF, phase diagram. ALUMINUM is produced commercially by the electrolytic reduction of aluminum oxide dissolved in molten cryolite. There is considerable controversy over the actual mechanism of the discharge processes, but sodium potentials in the systems appear to play an important role in the reduction mechanism. The metal-salt reaction involving NaF and aluminum to produce A1F3 and sodium is responsible for the presence of sodium in the aluminum metal phase. Additional sodium may be produced from the simultaneous deposition of sodium and aluminum at the cathode as a result of a cathodic overvoltage. runert' has suggested that sodium gas at atmospheric pressure would be the result of reaction between cryolite and aluminum at 1000°C. Subsequent investigations have shown that production of sodium at atmospheric pressure does not occur. These later investigations can be conveniently separated into two categories. The first involves sodium, aluminum, and cryolite, in which the sodium activity was measured. The second includes a lead phase for sodium activity measurement. Jander and errmann,' studied the reaction: at 1090°C in alumina crucibles under an atmosphere of dry, oxygen-free nitrogen. The equilibrium constant for the reaction was expressed in terms of concentration. Their results in Fig. 1 show an increase in sodium content of the aluminum with increasing NaF/A1F3 weight ratio. Pearson and waddington3 performed similar experiments at 1000°C. Their results are included in Fig. 1. Dewing and ollinshead have measured the sodium content of aluminum as a function of the NF/AF, ratio at 1025"C, Fig. 1, and ewin' measured the sodium content of the aluminum in a system involving the solid reactants NaF, cryolite, and liquid aluminum. This reaction is different from those discussed above. Two solid phases, NaF and Na3A1F6, and a liquid aluminum phase were present. The sodium concentration in the aluminum was determined by the temperature. Dewing's measurements covered the temperature range 679" to 896°C. Omo, Matsushima, and 1t02" investigated the equilibrium 6NaF ential thermal analysis. Stokes and Frank6 determined sodium activities by

Jan 1, 1970

By C. D. Williams, C. E. Ells

The susceptibility of quenched and aged Zr-2.5 wt pct Nb alloy to embritt2ement during irradiation has been examined for a number of solution temperatures and aging times. Material quenched from temperatures approximately 40°C below the transus has high tensile ductility, and this ductility is insensitive to aging at 500°C or to irradiation. If, however, the material is quenched from temperatures above the transus it becomes highly susceptible to loss of ductility either from aging at 500 or from irradiation. Inter granular failure is characteristic of the materials having low ductility. The distribution of the equilibrium phase is found to control the susceptibility to embrittlement by restricting 6 grain growth during heat treatment and thus influencing crack propagation. IN zirconium, as in titanium, -stabilizing alloy additions are used to obtain high strengths via quench and age heat treatments, and the Zr-2.5 pct Nb alloy has been developed1 because of its strength advantage over the Zircaloys. Early in the development of the Zr-2.5 pct Nb alloy the problem of 13 embrittlement was appreciated, and for this reason the solution temperature was chosen below the p transus.' In the course of irradiation studies on quenched and aged Zr-2.5 wt pct Nb alloy it was found' that irradiation introduced an important aspect of p embrittlement, riz., material quenched from the phase and aged 24 hr at 500°C was severely embrittled by moderate doses of neutron irradiation. This effect had not been studied in titanium alloys. In titanium the metallurgical features leading to 0 ernbrittlement were found to be structures with: a) coarse a platelets at the grain bondaries, b) finely dispersed a uniformly distributed throughout the (0) matrix,6 c) Widmanstatten a-13 with more than 50 pct P, d) the presence of some metastable p transformation products,3 and e) large prior -phase grain size.5 Alternatively, the presence of a uniform distribution of coarse a was conducive to high ductility and a structure largely of equiaxed a was very dctile. The detailed mechanisms of the embrittlement have not been worked out for all of these conditions, although weakness at either a-matrix boundaries or prior p grain boundaries have been prominent in the eculation. It was proposed that acicular a might act as a mild notch, and low ductility has been associated with easy fracture along its boundary.' There have been two opposing suggestions for the source of the high ductility associated with equiaxed a phase. JaffeeB proposed that this a would accept a large por- tion of the oxygen, thus increasing the ductility of the matrix, whereas after study of a Zr-Nb-Cu alloy Weinstein and oltz proposed that the a phase, softer than the martensitic matrix, acted to blunt cracks formed in the matrix. In the present work we have studied the effect of neutron irradiation on the ductility, particularly the P embrittlement, of the Zr-2.5 wt pct Nb alloy. By a variation of solution temperature and aging time a variety of metallurgical conditions have been examined, and a range of resultant ductilities obtained. The ductility has been related to the material microstructure and mode of fracture. EXPERIMENTAL The alloy used in the present work came from two separate ingots fabricated into rod of 3/8 or i in. diam, Table I. For both batches the P transus temperature was approximately 890° C. Most of the heat treatments were done directly on lengths of the j} in. diam rod, after which the tensile test specimens were machined. Quenching was achieved by dropping rods from a dynamic vacuum into water, the cooling rate estimated to be 2 100°C per sec. For aging the rods were encapsulated in evacuated silica tubes. Round tensile test specimens, with gage diam and length 0.160 and 1.0 in., respectively, were used throughout and pulled at room temperature or 300°C on Instron tensile machines, at a crosshead speed of 0.05 ipm. Specimens were irradiated in the NRX and NRU reactors, in facilities described in previous publications.'0 The metallurgical conditions examined have been: All tensile test specimens were machined with axes in the axial direction of the swaged rod. Although the specimen had a degree of preferred crystallo-graphic orientation with basal plane normals both parallel with and perpendicular to the tensile axis, the material was comparatively isotropic." The techniques of thin foil examination in the electron micro-

Jan 1, 1970

By Mark J. Klein

The creep of 043 was studied over the temperature range 1650" to 3200°F and over the stress range 3000 to 44,000 psi. The steady-state creep rate over this range of stress and temperature can be expressed by the equation where A is a constant, is the stress, and is -0.8 x 103 psi-'. Over a narrow range of stress variations c0 a and for this proportionality n varies from 3 to 30 in accordance with the relation n = aB. Above about 2400° F, H, the apparent activation energy for creep, is 110,000 cal per mole, a value about equal to that estimated for self-diffusion in this alloy. Below 2400°F, H increases with decreasing temperature reaching a value of -125,000 cal per mole at 1700° F. In this temperature region, H appears to be a function of the interstitial concentration of the alloy. MOST of the detailed creep studies of dispersion strengthened metals have been concerned with metals having fcc structures. However, there are a number of important refractory alloys with bcc structures that derive part of their high temperature strength from an interstitial phase and whose creep behavior has not been well defined. This paper describes the creep behavior of the bcc alloy, D43, over the temperature range 1650" to 3200°F (0.4 to 0.7 Thm) and over the stress range 3000 to 44,000 psi. In addition to colum-bium, this alloy contains 10 pct W. 1 pct Zr, and sufficient carbon (-0.1 pct) to form a carbide dispersion throughout the matrix of the alloy. The effects of variations in temperature and stress on the steady-state creep rate of this alloy are presented in this paper. EXPERIMENTAL PROCEDURES Creep tests were made in a vacuum of 106 torr under constant tensile stress conditions using a Full-man-type lever arm.' Creep specimens were machined from 0.020-in. D43 sheet (grain size -5 x l0-4 in.) processed in a duplex condition (solution annealed -2900°F, 40 pct reduction in area, aged 2600°F). The specimens were tested in this condition without further heat treatment. Specimen extensions over 1-in. gage lengths were continuously recorded using a high temperature strain gage extensometer. Differential temperature and stress measurements were used to determine temperature and stress dependencies of the creep rate. Activation energies were calculated from the changes in strain rate induced by abrupt shifts in the temperature during constant stress creep tests. The 100°F temperature shifts used in most of the activation energy determinations required 15 to 90 sec depending upon the temperature at which the shift was made. The dependence of strain rate on stress was determined by measuring the change in strain rate for incremental stress reductions during constant temperature tests. It has been shown that columbium-base alloys such as D43 are susceptible to contamination by gaseous interstitial elements during vacuum heat treatments.' In this regard, it is unlikely that these alloys can be heat treated without some loss or gain of interstitial elements despite the precautions taken to control the heat treating environment. However, several factors suggest that changes in interstitial concentrations of the specimens during testing did not affect the results presented in this paper. First, the dependence of the creep rate on the stress or temperature determined during the course of a single creep test showed no variations with the duration of the test. A variation would be expected if a loss or gain in interstitial concentration during the course of the test affected results. In addition, precautions taken during this investigation to minimize interstitial contamination by wrapping the gage lengths of the specimens with various foils2 (Mo, Ta, W) did not produce a detectable change in the stress and temperature dependencies relative to the unwrapped specimens. The averages of duplicate analyses for carbon and oxygen in several specimens determined before and after creep testing are listed in Table I. The combined nitrogen and hydrogen concentrations which were ordinarily less than 50 ppm did not change in a detectable way with creep testing. The analyses show that only minor changes in carbon concentration occurred during creep testing except for specimen 4. This specimen which was tested at 3100°F lost a significant amount of its carbon concentration to the vacuum environment. Specimen 1 gained 100 ppm of O, while specimens 2, 3, and 4, which were tested at progressively higher temperatures, lost increasing portions of their initial oxygen concentrations during testing. RESULTS AND DISCUSSION The Temperature Dependence of the Creep Rate. The apparent activation energy for creep, H, was de-rived from creep curves similar to that shown in Fig. 1. Steady-state creep was rapidly attained at the beginning of the test and with each change in temperature. This behavior suggests that the alloy rapidly attains a stable structure with each shift in temperature or that the structure is constant throughout the test. Since the dispersion will tend to stabilize the structure, the latter is probably the case. The activation energy was found to be independent of the direction of the temperature shift and the magnitude of the shift (50" or 100°F). Although H was approximately independent of the strain, there was a tendency for it

Jan 1, 1970

By Hsun Hu, B. B. Ruth

The rates of migration of high-angle boundaries in zone-refined aluminum crystals rolled 20 to 70 pct in the (110)[i12/ orientation were studied. Following a recovery anneal at an appropriate temperature to stabilize the polygonized structure, boundary migration rates of artificially nucleated grains were measwed isothermally at several temperatures. Results indicate that the rate of boundary migration depends strongly on the amount of deformation and on the cell size of the polygonized matrix, and is related to the driving free energy by a power function. The degree of anisotropy in growth 0.f the re crystallized grains nn&apos;th preferred mientation is independent of deformation; the migration rates of the fast-moving and the slow-moping boundary segments of a gowing grain differ by as much as one order of magnitude. The actir\ation energy fm a grain boundary migration, although nearly the same for both the fast-moving and the slow-moving boundaries for a given deformalion, decreases from 45 to 30 kcal per mole with an increase in deformation from 20 to 70 pct reduction. Re crstallization by the growth of the artificially nucleated grains results in preferred orientation. The Percentuge of&apos; grains favorably oriented for growth increases with increasing deformation. None of these grains corresponds to the ideal Kronberg-Wilson orientation relationship. The observed growth aniso-tropy is discussed in terms of boundary structure. The boundary velocity as a function of the cell inter -facial area, or the driving free energy, is discussed in the light of current theories of boundary migration. It is well established that recrystallization with re-orientation occurs by the migration of high-angle boundaries of strain-free grains. The driving force for this process is provided by the free energy stored in the metal during deformation. A quantitative study of the effect of varying driving force on grain boundary migration in deformed metals has not been possible heretofore, primarily because of: 1) concurrent recovery steadily decreasing the available driving free energy for boundary migration, &apos;-3 and 2) in-homogeneity of strain in the deformed metal.4 Aust and Rutter3 studied grain boundary migration in striated single crystals of zone-refined lead. Although the driving free energy in such crystals remains unaltered during annealing, this method does not provide a range of driving free energies over which measurements of grain boundary migration can be made. In the present investigation, the rates of migration of high-angle boundaries in deformed aluminum zone- refined single crystals were studied at various temperatures, after deformation ranging from 20 to 70 pct reduction by rolling at -78°C in the (ll0)[i12] orientation. The boundary migration rates along different crystallographic directions were determined under steady-state conditions, i.e., in the absence of competing recovery processes or impingement of recrystallized grains growing into the deformed single crystal matrix. Simultaneous recovery was eliminated by suitable anneals prior to the boundary migration measurements. The recrystallized grains, which grew a ni so tropically into the homogeneously polygonized matrix, developed flat boundary segments during early stages of growth. These boundary segments subsequently migrated along a direction approximately normal to the boundary plane into the matrix rystal. Increasing deformation over the range employed was estimated to increase the driving free energy for boundary migration by about five times. The kinetics of the boundary migration process, examined under these conditions, indicate that the boundary velocity is greatly affected by a small change of the driving free energy in the matrix crystals. These results were examined in the light of the current theories of grain boundary migration. EXPERIMENTAL PROCEDURES Single crystal strips (9 by 1 by 0.125 in.) of zone-refined aluminum, were seed-grown by the Bridgman method in a high-purity graphite mold (<lo ppm ash) at 1 in. per hr. Precautions were taken to minimize contamination of the metal during crystal preparation and subsequent handling. Spectrographic analysis of the metallic impurities in the grown crystals is Qven in Table I. The crystals were rolled in the (110)[112] orientation at -78°C to various reductions in thickness, ranging from 20 to 70 pct, in 10 pct increments. The desired reduction was achieved by many rolling passes, each being no more than 0.002 in. To minimize surface friction, the crystal was rolled between two thin layers of teflon. For those crystals rolled more than 40 pct, it was necessary to remove the disturbed surface layers by electropolishing at -5" to -10°C at an intermediate stage of rolling. The edges of deformed crystals were removed by a jeweler&apos;s saw while submerged in alcohol at -78° C to obtain samples of about ? by i in. The distorted metal at the cut edges and the surface layers were then removed by electropolishing, with removal of a minimum of 0.004 in. from each surface. The thickness of the crystals prior to rolling was chosen so that the final thickness was 0.025 in. for all samples. These deformed single crystals were each prean-nealed for 1 hr at an appropriate temperature in the range of 130" to 280°C, depending upon the amount of deformation. The purpose of this preannealing was to

Jan 1, 1970

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By Thomas C. Wilder, Walter E. Galin

Measurements of the electromotive force of the cell at 995°C have shown that the cell may be used to detennine the zinc content of molten Cu-Zn alloys to the nearest 0.05 wt pct. The cell is used for brass melts to which no ZnO is added intentionally, because essentially all oxygen in the Cu-Zn-O system is present in the form of ZnO. The cell is also used to detev,nine the thernodynamic activity of zinc for Cu-Zn al1oys of the brass composition range, from which the equilibrium partial pressure of zinc for such alloy may also be calculated. The electrochemical measurement of the concentration of the most active metal in other engneering- alloy systems by a similar technique is also considered. IN recent years there have been many studies concerning the direct electrochemical measurement of oxygen content in molten engineering metals.&apos; These investigations employ galvanic cells in which the electrolytes are various solid mixed-oxides which conduct current by movement of oxide ion vacancies under the influence of an oxygen potential gradient. Similar cells have also been used to measure the thermodynamic properties of mixing of solid alloys,&apos; one component of which has a much greater affinity for oxygen than the other component(s). One alloy system of obvious engineering importance comprised of two metals of greatly differing affinity for oxygen is copper-zinc. At the casting temperature of molten brasses, the zinc concentration is very difficult to control not only because its vapor pressure is very high, but also because of its high affinity for oxygen to form ZnO. Inasmuch as brass castings may be required to have a zinc concentration within very narrow limits, it would be advantageous for the brass industry to have a means for quickly measuring the zinc content in the molten alloy just prior to pouring. A calculation based on earlier thermodynamic studies of oxygen and zinc in dilute solution in binary Cu-O and CU-Z&apos; alloys indicates that the oxygen concentration of molten 70 wt pct Cu-30 wt pct Zn brass must be much less than 1 ppm for the separate phase ZnO not to exist in the ternary Cu-Zn-O system. Thus it can be assumed that all molten brasses, both in the laboratory and in the foundry, are sufficiently saturated with oxygen for the separate phase ZnO to be present. In view of the foregoing reasons, the cell investigated at 995°C for the purpose of measuring the zinc concentration in molten copper-zinc alloys, particularly those of brass compositions. In this cell the left hand electrode is a reference electrode comprised of a mixture of the pure powders of nickel and nickel oxide, to which a platinum contact is made. The electrode of interest is a molten Cu-Zn alloy of unknown zinc concentration with a tantalum wire contact. The electrolyte is the commercially available (Zircoa) calcia stabilized zirconia. The ZnO in the Cu-Zn electrode compartment is not intentionally added, but is naturally present as a result of the infinitesimal amount of oxygen required for its formation in this alloy system. In cell [A] nickel oxide is reduced at the cathode where O= represents the electrolyte. At the anode dissolved zinc of the Cu-Zn alloy is oxidized to form ZnO(s) in its standard state Thus the overall reaction is for which the molar free energy change is where 5 is the Faraday equivalent (23,063 cal per v equivalent), is the electromotive force of the cell in volts after correction for the Pt-Ta thermocouple, FOf (ZO) and AFF (NO) are the standard molar free energies of formation of the respective oxides, and a2n is the thermodynamic activity of zinc in the molten Cu-Zn alloy. The reference state of zinc in this case is taken to be the pure liquid. At constant temperature all the terms of Eq. [I] are constant except and azn Thus since all other participants in the electrochemical reaction are in their standard states, the change in the electromotive force of Cell [A] is represented only by a change of the thermodynamic activity of zinc at constant temperature. The zinc concentration is related to the activity by sampling the alloy for chemical analysis after cell measurements are taken. EXPERIMENTAL A typical cell construction is shown in Fig. 1. This and other experimental details were similar to that described earlier with the exception of some minor modifications which are detailed below.

Jan 1, 1970

By G. Sandoz, D. A. Meyn

The fracture surfaces of specimens of titanium a1loys which exhibited susceptibility to subcritical crack growth in a wide variety of environments, including aqueous solutions, alcohols, hydrocarbon gases, carbm tetrachloride, and dry air, were examined. The dominant and characteristic fracture mode was cleavage. which became mixed with an increasing porportion of ductile fracture modes (dimples. and so forth) as the applied KI was increased. The cleavage plane in all the alloys was oriented at 15 deg from (0001) of the a phase. No indices could be assigned to the 15 deg cleavage Plane because of uncertainty as to which zone it belonged to. SLOW crack growth and delayed fracture take place in certain titanium alloys at stress intensity (KI) lower than the critical values for complete fracture (KIc) found in short-time tests for plane strain fracture toughness.&apos; Such crack growth may take place in very dry air on sustained loading if the alloy contains a sufficient amount of hydrogen and if the stress intensity factor is higher than a threshold value designated KIH.2 Similarly, a number of environments such as water, alcohols, and hydrocarbons may cause slow crack growth provided the stress intensity factor exceeds the threshold value KISCC. In this paper it is intended to examine some fracto-graphic and crystallographic details of this subcritical crack propagation process as related to alloy composition, environment, and stress intensity. It has been previously reported that subcritical crack growth takes place in titanium alloys in aqueous environments by cleavage.2"6 The observations to be described here indicate that in the alloys investigated the mode of subcritical crack propagation is more dependent on the stress intensity during cracking than on the environment. The fracture mode is illustrated with photographs of the fracture surfaces at a wide range of magnifications. The crystallographic character of the cleavage mode is also presented and the results discussed. EXPERIMENTAL APPROACH The studies were made on four titanium alloys— Ti-8A1-1Mo-lV, Ti-5A1-2.5Sn, Ti-7Al-1Mo-lV, and Ti-0.350. Of these four alloys the first two were mill annealed and fine grained. The latter two were noncommercial and coarse grained, having been prepared for other experimental purposes. The crystallographic studies required a large-grain size. Consequently the fine-grained alloys were an- nealed in a vacuum at 1950°F and furnace cooled to produce samples for these studies. This treatment did not alter the microstructure significantly except for grain size. All the aluminum-containing alloys showed primary a with a network of ß-phase particles within the a grains; Figs. 1 and 2 show this microstructure for the specific case of fine-grained Ti-8A1-1Mo-1V. The cracks in the figures will be discussed later. Fractographic studies were made on all the alloys, but the electron fractographs displayed herein are from the Ti-8A1-1Mo-1V alloy in the fine-grained condition. Emphasis was placed on this commercial alloy because considerable information was available on the stress-corrosion cracking characteristics in a variety of environments. Sufficient supplementary studies of the alloy after the anneal to produce large grains were conducted to establish that the stress-corrosion cracking susceptibility and fractographic characteristics were not changed significantly. Thus it could be inferred that the crystallographic data obtained exclusively on large-grained specimens would apply also to fine-grained specimens. Fracture surfaces for study were obtained using precracked cantilever beam specimens loaded as described by Brown. The precracked section of a specimen was immersed in the environment of interest. Values of initial stress intensity factor Kli were chosen slightly higher than KISCC in order to obtain a fairly extensive region of slow crack growth. Fracture surfaces representative of a variety of stress intensity levels could then be examined because in the cantilever beam test KI increases as the crack propagates.

Jan 1, 1970

By W. L. Mamme, G. Y. Chin

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain was analyzed by Taylor and by Bishop and Hill in terms of a minimum (internal) and a maximum (external) work criterion, respectively. These two criteria have now been generalized to include crystallographic slip on several sets of slip systems, twinning mixed with slip, and slip by (noncrystallographic) pencil glide. The generalized treatment also takes into account the possibility of a Bauschinger effect and of unequal hardening among the shear systems, which were considered in the Bishop and Hill work. Optimization techniques of linear and nonlinear programming are shown to be applicable for the numerical calculation of the minimum or maximum work. In the case of crystallographic shear, the constraint functions are linear and hence the optimal work is obtained as the saddle value of the lagrangian function Wi(y) e minimum and W,(u) + (a) for the maximum, where Wi is the (internal) work, We is the (external) work, Y is the crystallographic shear strain, u is the applied stress, and and are constraints. It is shown that the Lagrangians are functionally the same and the saddle value of one problem is identical to the saddle value of the other, proving that the two analyses are completely equivalent. In the case of pencil glide, although the constraint functions are nonlinear and neither convex nor concave, the equivalence of the optimal values to the saddle value of the Lagrangian (which is again identical for both problems) is still valid. WHEN a crystal deforms plastically by crystallographic shear, five independent shears are generally required to accommodate five independent strain components specifying the deformation. Assuming slip as the only shear mechanism, Taylor1 in 1938 analyzed the deformation in terms of a minimum work criterion. He hypothesized that of all combinations of five slip systems which are capable of accommodating the deformation, the active combination is that one for which the internal work C is a minimum, where 1 TI is the critical resolved shear stress for slip on the 1-th slip system and is the corresponding simple shear. By further assuming equal 72 for all equivalent slip systems and no Bauschinger effect, Taylor re- duced the minimum work problem to one of minimum and applied the analysis to the case of axisym- Metric flow by {111}(110) slip in fcc crystals. However, he did not consider the question of whether the resolved shear stress has in fact attained the critical value for slip on the newly found active systems without exceeding it on the inactive systems. In 1951 Bishop and ill&apos; put forth the maximum work analysis in which slip is again assumed as the only deformation mechanism. In this analysis, the work o1 done in a given strain ij by a stress ujj not violating the yield condition is maximized. In addition, the analysis takes into account the possibility that the critical resolved shear stress for slip may not be equal among the slip systems and that the slip behavior may exhibit the Bauschinger effect. As with Taylor, a single set of slip systems—{111)(110) — was analyzed numerically. It thus appears that the Bishop and Hill treatment is on a more sound physical basis than the Taylor treatment. However, Bishop and Hill showed that where there is equal hardening among all slip systems and when there is no Bauschinger effect, Eq. [11 ] of Ref. 2, as assumed by Taylor, the results of their maximum work analysis are the same as those of Taylor&apos;s minimum work analysis. Hence at least under those conditions there is an implication that the Taylor analysis does lead to a critical resolved shear stress for slip on the predicted active systems without violating the yield condition on the inactive systems. Recently, the Taylor analysis was applied for numerical solutions of the axisymmetric flow problem, for slip on {110}(111), {112}(111). {123)(111) systems as well as a mixture of all three sets of svstems."1 Computational techniques based on the optimization theories of linear and nonlinear programming4 were employed in these solutions. The same techniques were employed in the solutions of an axisymmetric flow problem of deformation by slip on (111) (110) systems and twinning on (111)(112) systems5 which had been considered theoretically from a modified Taylor approach. The utilization of these techniques has led to the realization that the solutions of Taylor&apos;s minimum work problem imply the solutions of Bishop and Hill&apos;s maximum work problem. The two problems turn out to be dual problems in the well known sense of mathematical programming. It is thus the purpose of this paper to first generalize the minimum and maximum work analyses to include crystallographic slip on several sets of slip systems, twinning mixed with slip, and slip by (non-crystallographic) pencil glide, as well as the possibility of a Bauschinger effect and of unequal hardening

Jan 1, 1970

By J. Szekely, V. Stanek

Heat and gas flow interactions in nonisothermal packed beds were examined in the paper. A study was made of the response of the system to a step or pulse change in the inlet gas temperature, with a fixed value of the overall pressure drop across the bed. Under these conditions the heat flow and fluid flow transients are coupled because the convective heat transfer rate is alfected by the mass flow rate of the gas which, in turn, for a fixed pressure drop will depend on the temperature profile in the system. The Problem was stated in terms of differential equations, which were integrated numerically. The parameters used in the computation were so chosen to reflect the operation of the stack region of blast furnaces and sinterbeds. The computed results showed that the pressure drop-flou1 relationships and the rate of progress of the temperature fronts (waves) were strongly interrelated and were also markedly affected by variations in particle size and in void fraction. MANY metallurgical processes involve the contact of solid particles with a gas stream in a packed bed arrangement under nonisothermal conditions. Examples are shaft furnaces, regenerators, pebble heaters, and the sinter process. Although the heat and mass transfer aspects of packed bed processing have been extensively studied, the associated flow phenomena and in particular the effects of nonisothermality on the flow, have received little attention to date. :In fact, most of the previous workers considered the flow rate of the carrier gas time invariant and independent of the heat or mass transfer processSzekely and carr2 have shown that the pressure drop-flow relationships in nonisothermal packed beds may be strongly affected by the temperature profile within the system. These authors have devised a method for relating the pressure drop to flow for a given temperature profile. thus providing an extension of the Ergun equation to steady nonisothermal systems. Finally, in a recent paper willmot3 examined the response of regenerators to externally imposed changes in the gas flow rate. Both these investigations were somewhat specialized since, in general, neither the temperature distribution nor the gas flow rate may be regarded as truly independent variables, thus the heat transfer and the fluid flow problems have to be solved simultaneously. The work reported here is divided into two parts: in Part 1 the general formulation is given and a detailed discussion is presented of fixed bed systems. Part is devoted to systems in which a gas and particulate solids are contacted in a counter flow arrangement. FORMULATION Consider a nonisothermal fixed packed bed, extending from through which a gas is flowing. The problem is to develop a relationship between pressure drop and gas flow (with the gas flow being the dependent variable) and to evaluate the rate at which a change in the gas temperature, imposed at the inlet, travels through the system. Let us consider an infinitesimal section of the bed and establish differential heat, mass, and mechanical energy balances over this region. In addition, relationships are needed describing the temperature dependence of gas density (equation of state) and the temperature dependence of viscosity. These may be written as: where c, and are constants. It is noted that in this formulation we neglected any temperature gradients within the solid particles, thus assuming these to be either sufficiently small or of sufficiently high thermal conductivity to meet this condition. The justification and consequences of this assumption will be mentioned in the discussion.

Jan 1, 1970

By J. Szekely, V. Stanek

Steady state heat transfer and fluid flow rates are predicted for the counter-current contacting of gas and solid streams. For a .fixed pressure drop across the bed the convective heat transfer rate is affected by the gas flow rate, which in turn is affected by the temperature distribution in the system. Variations in bed voidage and in particle size were found to change the predicted temperature profiles quite markedly, in particular when the thermal capacities of the gas and solid streams were equal. IN Part I we examined the effect of step and pulse changes in the inlet gas temperature on transients in the flow of gases through fixed packed beds. Here we shall discuss heat flow and fluid flow interactions in the counter-current heat exchange between packed solids and a gas stream. Counter-current heat exchange in packed beds has been extensively studied. In his now classical paper, Furnas&apos; assumed constant property values and developed a simple analytical. expression for the temperature profiles in the gas and in the solid stream. A highly sophisticated analysis of counterflow systems, allowing for transients and interparticle conduction was developed by Amundsen. In preparing a very readable review of this topic Elliott&apos; also presented a number of elegant solutions, including the case involving heat generation. A great deal of work has been done on the application of these concepts to the modelling of the blast furnace. However, in all this previous work the mass flow of the gas was regarded as a quantity independent of the gas-solid heat exchange process. In the following we shall consider counter-current heat exchange between a gas stream and a packed bed of solids, under conditions where the pressure drop across the bed is specified, rather than the mass flow of the gas. FORMULATION Consider a packed bed, extending from y&apos; = 0 to y&apos; = L, in which moving solids and a moving gas are contacted in a counterflow arrangement. Let cold solids, with an initial temperature Tsi and mass flow GA, enter at y&apos; = L, and hot gas with an initial temperature of Tgi and mass flow Gg enter at y&apos; = 0. In contrast to the problems considered in Part I this system has a nontrivial steady state and we shall restrict our attention to the study of the pressure drop flow relationships and the resultant temperature distributions for steady state conditions. Under these conditions the formulation of the problem requires the statement of the following: 1) heat balance on the gas 2) heat balance on the solids 3) the mechanical energy balance equation and in addition the knowledge of the equation of state, and a functional relationship between viscosity and temperature and an expression for the heat transfer coefficient in terms of the other parameters. On neglecting temperature gradients within the solids and for a constant mass flow of the gas, the solution to this problem is well known.&apos;" The expressions for the temperature profiles of the gas and solid streams may be put in the following form: where Tg and T, denote the dimensionless gas and solid temperatures respectively, y is a dimensionless distance, and R is the ratio of the thermal masses. These quantities are defined as follows: For the particular case of equal thermal mass capacities by the gas and the solid, that is R = 1, the Eqs. [1]and[2] simplify to Eqs. (71 and[8], respectively: i.e., the resultant profiles are linear. As for most practical cases , solutions given by Eqs. [7] and [8] will contain only the inlet temperatures as parameters. For a fixed, predetermined value of C;b the above

Jan 1, 1970

By M. Marciano, K. Kreider

Silicon carbide coated boron fiber (Borsic) reinforced aluminum composites were made which exhibit strength and modulus values predicted by the rule of mixtures. A successful technique for fabricating these composites consists of plasma spraying of monolayer filament reinforced tapes and subsequent diffusion bonding of these tapes into composites. The elastic properties of the composites were given by the rule of mixtures in reinforced directions. (The modulus parallel to the fibers was 32 x 106 psi for a composite with 50 pct by volume fibers. The other elastic properties for a composite with 50 pct fiber were transverse modulus = 14 to 16 X 10 psi, G = 9.5 x 106psi, and v,, = 0.23. Tensile strengths of over 190,000 psi were measured for the composites with 50 pct fiber and the average strength for these composites was 162,000 psi. These same composites had interlaminar shear strengths of 12 to 15,000 psi. Multidirectionally reinforced composites demonstrated the same reinforcement efficiency in strength and modulus as the uni-directimlly reinforced composites. Comrpessive strengths of composites with 50 pct by volume fiber were found to be greater than 250,000 psi. STRUCTURAL filamentary composite materials are being considered for use where high strength, high modulus, and lightweight materials are required. Metal matrix composites have been considered for use at temperatures ranging from cryogenic (aluminum stainless steel) to 6000°F (plasma sprayed tungsten plus tungsten fiber) and other requirements have been similarly diverse. Metal matrix composites offer high modulus and high strength in unreinforced directions, the ability to be joined by brazing or welding, and greater fracture toughness compared with the more easily fabricated resin matrix composites. This paper deals with the mechanical properties of aluminum boron composites, a system which is being considered for applications where lightweight, high modulus, and high strength are required at temperatures including those above the normal operating temperatures of resin composites. The boron fiber used in this investigation had an average room temperature strength of greater than 400,000 psi, a modulus of 58 x 106 psi, and a density of 0.09 lb per cu in. (2.6 g per cu cm).&apos; The fiber used in the composites had a coating of silicon carbide to retard degrading reactions with the matrix at elevated temperatures. The coated fiber, which is sold commercially as Borsic: has been reported to have excellent resistance to degradation at temperatures up to 600°C in air and in aluminum2 and the same mechanical properties as the standard bare boron fiber. Fabrication of Composites. The composites were diffusion bonded from plasma sprayed monolayer tapes. These tapes were fabricated on a substrate of aluminum alloy foil which is incorporated in the composite matrix. The technique consists of winding a layer of fiber on the foil, and plasma spraying the balance of the matrix alloy over the windings which bonds all of the components together. Advantages of this process include the ability to achieve good fiber spacing, Fig. 1, the formation of a good bond between fiber and matrix (achieved during the plasma spraying), and the adaptability of the process for forming large and complex parts. This is particularly true when used with brazing foil backing which alloys low pressure bonding of the structural shape. PROPERTY EVALUATION TECHNIQUES Tensile test specimens, 5 to 7 in. long with a reduced gage section and ,030 to ,040 in. thick, were cut from composite sheets with a diamond saw. The gage section was .200 in. wide, while the gripped section was .240 in. wide and over 2 in. long in each grip. The standard gage length used was 1 in., however, transverse specimens (i.e., specimens with the fibers oriented 90 deg to the loading axis) were tested without a reduced section. Twelve specimens were also made with a 3-in. gage length but no significant effect of gage length was measured. The tensile test specimens were mounted in a fixture and aligned in friction grips using a 10X microscope. Unbonded foil doublers (0.010-in.-thick aluminum) were used to insure firm gripping with a minimum of damage to the fibers. The test specimens were transferred to the testing machine in a rigid fixture and mounted in the self aligning loading train. Testing was performed using a Tinius Olsen four screw testing machine with a torsion bar LVDT load

Jan 1, 1970

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw&apos;1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By W. R. Kanne, P. R. Strutt, R. A. Dodd

A study has been made of the creep behavior of ß-NiAl of stoichiometric composition in the temperature range 475" to 775°C. Single crystal tensile specimens were deformed under a constant applied load. From slip line studies and tensile axis rotations it was concluded that the crystals deformed by pencil-glide on (100) and (110) planes with a (100) slip direction. Electron microscope thin-film studies showed evidence for profuse cross-slip, and the dislocation Burgers vector was determined to be (100). There was no tendency for the dislocations to lie in definite slip planes, although a strong alignment of segments of edge dislocations was frequently seen. The activation energy for creep in the temperature range 475" and 775°C was judged to be much lower than that for creep at temperatures above 775°C. It is possible that the rate-controlling process is the thermally activated cross-slip of screw dislocations. In recent years considerable interest has developed in the possible use of high-melting-point intermediate phases for high-temperature applications necessitating good creep resistance. Ordered alloys such as Ni3A1, modified by alloying additions, have received particular attention, culminating in the recent development by Pratt and Whitney of single crystal turbine blades.&apos; The intermediate phase NiAl has considerable theoretical interest from a creep standpoint because not only is it ordered up to the melting point (-1650°C at stoichiometry) but it contains a high concentration of structural vacancies on the aluminum-rich side of stoichiometry. These vacancies are known to exert a strengthening effect under some conditions,&apos; but in addition they might be expected to affect high-temperature creep rates through dislocation climb. The present paper deals with the slip line and dislocation structures developed during creep of stoichiometric NiAl between 475" and 775C, and with possible attendant creep mechanisms. MATERIALS AND TEST TECHNIQUES NiAl ingots of stoichiometric composition were prepared by induction melting 99.996 pct A1 and 99.98 pct Ni (kindly provided by the Kaiser Aluminum Co. and the International Nickel Co., respectively) in 100 cc pure alumina crucibles in a helium atmosphere. No chemical melting flux was used in order to avoid con- tamination of the alloy. Each ingot was slowly direc-tionally solidified to avoid porosity and to produce very large grains up to 2 in. in length. In this way, ingots were obtained which were suitable for sectioning into single crystal creep specimens. Chemical analysis indicated that all alloys were within the range 49.6 0.3 at. pct Ni. For the present investigation, identical rectangular single crystal blanks were cut vertically from one particularly large crystal in an ingot using a series of three diamond cut-off wheels with appropriate spacers. Thus, all sliced crystals had the same orientation with the tensile axis parallel to the long side of the rectangle; the initial orientation of the tensile axis is shown as S, in Fig. 1. The blanks were homogenized at 1250 to 1300°C for 48 hr and subsequently cooled slowly to room temperature. A gage length of rectangular cross section and about 0.75 in. in length was prepared on each specimen using an electrolytic lathe and a dilute nitric/phosphoric acid electrolyte. The gage length cross section was 0.250 0.0005 in. by 0.040 ± 0.0005 in. Holes to accommodate tensile grips were electrolytically machined using a rotating acid jet. After creep testing, this same technique was used to cut discs for transmission electron microscopy. Thus, all shaping was done electrolytically, the only exception being that (122) sections were spark-machined from some speci-

Jan 1, 1970

By R. Wang, N. J. Grant, B. C. Giessen

By crystallographic and X-ray methods, the existence and isonzorphism of Ti3Rh5 and Hf3Rhs were confirmed. Both phases are of the orthorhombic Ge3Rh5 type; lattice parameters and refined positional parameters are given. The structure is related both to the filled-up NiAs-B8 and Cu-AI types. An analogous phase with zirconium does not exist; the effect of ternary substitutions for titanium ad hafnium suggests a size factor limit to be active. A recent survey of phase diagrams of the T4 metals titanium, zirconium, and hafnium with the T, noble metals rhodium and iridium indicated the existence of the A3B5 phases Ti3Rhs, ZrsRhs, and HfsRhs. Ti3Rhs and Hf3Rh5 were found to be isostructural, based on the line-rich powder patterns which had not been analyzed. Zr3Rh5 was considered to have a substructure of the NbRu type (orthorhombically distorted B2-CsCl type).&apos; Because, in combinations with other transition metals, hafnium and zirconium are generally more likely to form isostructural phases than hafnium and titanium (with the significant exception of the Ti2Ni-"E93" type phases based on T4 metals2), the reversal of this relation for the A3B5 phases was of interest. As shown in the following, the nonexistence of Zr3Rhs has been established, the structures of Ti3Rh5 and Hf3Rh5 have been worked out, and crystal chemical relationships and stability criteria are reported. EXPERIMENTAL METHODS AND RESULTS Alloy Preparation and Phase Diagram Work. Alloys were prepared from high-purity (99.99+ pct) elements by arc-meltin3,4.Heat-treated alloys were annealed in a vacuum of 3 x X torr for 24 hr at 1300DC. Metal-lographic samples were etched electrolytically in concentrated HCl with 5 v ac for 5 min.3 X-ray diffraction powder patterns were taken on a GE XRD-5 dif-fractometer with Cum radiation at low scanning rates (0.2 deg per min for 28). It was confirmed that Ti3Rhs and Hf3Rh5 have similar diffraction patterns, and that an alloy with the composition Zr3Rhs has a different pattern. Six Zr-Fh alloys with 59 to 69 at. pct Rh were therefore prepared and investigated in the as-cast state by X-ray diffraction and metallography. Alloys at 59 and 61 at. pct Rh were found to be a single phase, with the distorted B2-CsC1 type structure typical for the off-stoichio- metric region of the phase (Zr,-,Rh,)Rh. This phase forms a eutectic with ZrRhs at about 66 at. pct Rh: accordingly, alloys between 61 and 69 pct at. pct Rh consisted of two phases. There is no evidence for the existence of Zr3Rh5. Based on the results in Rafs. 1 and 5, on the present work on Zr-Rh, and on several additional alloys investigated, the portions between the AB and AB3 stoi-chiometry for Ti-Rh, Zr-Rh, and Hf-Rh are as follows: Further, several ternary alloys near Ti3Rhs and Hf,Rhs were prepared in which it was attempted to replace titanium and hafnium partly by zirconium, niobium, tantalum, and germanium. The results will be discussed in a later section. Structure Determination of Ti3Rh5. Since Ti3Rh5 and Hf3Rh5 are isostructural, the following discussion will largely deal with the former. Although the powder pattern of TisRhs is complex, as found previously,1 it could be indexed by comparison with other structures of A3Bs stoichiometry. Ti3Rh5 was found to be isostructural with Ge3Rh5, whose orthorhombic structure had been elucidated by Geller.9 As both the sizes and atomic numbers of germanium and titanium are comparable, the unit cell volume and the peak intensities could be expected to be similar; however, significant differences exist in the atomic positions, as will be shown. All lines in the powder patterns of Ti3Rh5 and Hf3Rhj could be indexed with primitive orthorhombic unit cells with the lattice constants: The fractional errors are 10 The low-angle portion of the indexed powder pattern of Ti3Rh with sin2 8 < 0.30 is listed in Table I. The extinction laws Okl only with k = 2n and hOl only with h - 2n are compatible with the space group Pbo2 and the more symmetrical space group Phnm of Ge3Rh5. Finally, the positional parameters of Ti3Rh5 and HfsRhs were refined under the assumption that titanium and hafnium occupy the germanium positions in Ge3Rh5. Integrated intensities were obtained from the diffraction patterns by planimetry. Intensities of overlapping reflections were separated by an iteration process incorporated into the least-squares positional refinement program according to a method described previously. The intensities of Ge3Rh5 were used in the first separation cycle, while the atomic parameters of Ge3Rh5 were used as starting values in the first refinement cycle. Absorption due to specimen

Jan 1, 1970

By Yuri D. Tretyakov, Robert A. Rapp

The stoichiometry ranges ofNiOl+y and LiFe,O,-d were established by high-temperatwe electrochemical meas7rements in a stabilized-zirconia electrolyte cell. The results were consistent with doubly ionized cation vacancies in NiO,+y and interstitial lithium or iron ions in . The defect structure of the ternary ferrite was derived from the consideration of equilibration with respect to oxygen between the solid and the gas phase. The absolute magnitudes of defect concentrations were calculated. Pavtial molar enthalpies of oxygen in the compounds were calculated and interpreted in terms of the enthalpy of defect formation in these crystals. NICKEL oxide (NiO,,?) is a metal-deficient, p-type, extrinsic semiconductor whose properties are consistent with a structural model based on the presence of cation vacancies as the predominant ionic defect at sufficiently high temperatures and oxygen activities. A survey of previously reported conductivity studies and the presentation of some more recent conductivity measurements will be given in a later paper.&apos; The absolute magnitude of the equilibrium vacancy concentration in NiO has been reported from combined conductivity and thermogravimetric data of &apos; However, disagreement exists concerning the state of ionization of the nickel vacancies in NiO. Some authors3-&apos; have proposed that the predominant defects in NiO are singly ionized nickel vacancies and positive holes (h&apos;) formed by the reaction where, accorhng to the notation of Kroger and Vink,6&apos;7 Oq represents an oxygen ion on its normal lattice site. Other authors"27E have proposed that doubly ionized nickel vacancies (V{i ) and positive holes are predominant and are formed by the reaction One purpose of the present investigation was to establish the nature of the predominant defect in NiO,+? as well as its equilibrium concentration and thermo-dynamic properties at elevated temperatures and known oxygen activities. To accomplish this purpose, the coulometric titration of oxygen into and out of NiO was accomplished using a galvanic cell involving the calcia-stabilized zirconia electrolyte. The ternary oxide, lithium ferrite (LiFe50,-6) is ferromagnetic and has the inverse spinel structure LiFe,O,-d Thus, in the ideal stoichiometric XY204 lattice, Fe3 ions occupy one-eighth of the tetrahedral (A) sites, and i&apos; and Fe3&apos; ions share at random one-half of the octahedral (B) sites within the fcc sublattice of oxygen ions.g The structure and thermodynamics of the spinel structures have been comprehensively decribed.&apos;-&apos; A recent compilation of literature for lithium ferrite is also available. 15 Oxygen-excess LiFe50sis not expected to exist because both i&apos; and 17e3& ions are in their highest normal valency states (positive hole formation is not favorable). As will be discussed, equilibration of the ferrite crystal with oxygen of a surrounding gaseous phase will result in the introduction of equilibrium concentrations of ionic and electronic defects. In the Results and Discussion section a defect model for LiFe50,-d is proposed. This defect model is tested by high-temperature coulometric titration experiments. EXPERIMENT The oxygen activities in nonstoichiometric NiOl+, (and also LiFe,O,-d) were measured by means of coulometric titration with the high-temperature galvanic cell The critical characteristic of a suitable experimental cell is the complete isolation of the phase to be investigated in a minimum sized chamber which is free from extraneous sources and sinks for oxygen (leakage). Then oxygen is only admitted to the chamber or removed from it in known amounts by coulometric titration, which involves the passage of oxygen ions through the solid electrolyte with electrochemical oxidation and reduction reactions at the platinum contacts to the electrolyte. The experimental cell is shown in Fig. 1. The cap of the cell was the tip from a closed-end alumina tube, which was found to be leak-free from a helium leak-detector test. This alumina cap was about 1.2 cm OD and about 1.5 cm high. A Zircoa calcia-stabilized zirconia tablet (crucible lid) of 1.5 cm diam and 0.3 cm thickness served as the solid electrolyte. A Pyrex ring of about 0.1 cm thickness was placed between the electrolyte and the cap. The electrolyte tablet was painted with platinum paste on the entire outer face and on that part of the inner face which would be within the enclosure; these electrodes were further prepared by heating in air at 1000°C for 2 hr. Nickel oxide powder, listed as 99.999 pct pure, was purchased from Leico Industries, Inc. Pills of the NiO were cold-pressed and sintered at 1050°C for 3 hr in a platinum crucible. This poorly sintered NiO was crushed, and chunks were wrapped in 52-mesh Pt gauze (to catalyze the solid-gas exchange) for place-

Jan 1, 1970

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By J. Szekely, J. W. Evans

A formulation is given for radiant heat loss from the surface of molten steel held in a ladle and numerical solutions are presented for the resultant integrodif-ferential equations. The results are shown on plots of the net rate of heat loss against time, with the geometlry, emissivities, thermal properties of the walls, and Preheat as parameters. It was found that the rate of the vadiant heat loss from the exposed metal surface was comparable to the conductive losses from the Portion of the metal in direct contact with the walls. The radiant heat loss was markedly affected by the geometry and by the thermal properties of the walls the net radiant heat loss from the steel could be drastically reduced by providing a top cover and also by the provision of preheat. The results of this work are thought to be relevant to heat loss calculatious concerned with vacuum degassing and with operatzons in which molten metals are held in ladles. WhEN molten steel is held or transferred in ladles heat losses inevitably occur. The accurate assessment of these heat losses is of importance in process design considerations, as the temperature of the metal may have to meet rigid specifications in certain stages of the processing sequence. As shown in Fig. 1, the principal mechanisms responsible for heat loss are: i) Conduction into the walls and ii) Thermal radation from the top metal surface (possibly augmented by natural convection) The conductive heat loss may be readily calculated as much information is available in the literature on both the general theory1&apos;&apos; and on its particular applications to ladle heat loss calculations. Evaluation of the radiant component of the heat loss is less straight-forward. In two recent papers it has been shown that the presence of a slag layer 2 to 3 in. thick would prevent any significant heat loss for periods up to an hour,5&apos;" however, should bare metal be exposed, constituting the radiant surface, substantial heat losses could occur. This latter case is of considerable practical interest in various degassing operations and in the vacuum processing of certain specialty steels, where the top surface of the metal is not covered by a protective slag layer. Under these conditions a substantial radiant flux is emitted by the top metal surface; part of this flux leaves the system, part of it falls in the ladle walls. The radiant flux incident on the ladle walls is in part absorbed and conducted away, and in part reflected and re radiated. The purpose of the paper is to present a general formulation of the problem, the resultant solution of which should enable computation of the net radiant heat loss from the metal surface. The principal variables, the effect of which will be investigated, include initial metal temperature, geometry, thermal and radiative properties of the wall, and various modes of preheat. FORMULATION Consider a cylindrical enclosure, shown in Fig. 2, with a diameter D, height H, and wall thickness W, the cover at the top of the cylinder having a wall thickness L. If the temperature of the base (representing the top surface of the metal) is kept constant, say, Tb, the problem is to calculate the net rate of heat loss from the base as a function of time, geometry, the initial temperature distribution, and the thermal properties of the system. As customary, the formulation will consist of the mathematical statement of the conservation of thermal energy within the system.

Jan 1, 1970

Jan 1, 1970