Search Documents

By C. E. Capes

INTRODUCTION In the coal industry, ever greater amounts of fine coal must be processed due to the need to crush to finer sizes for impurity liberation in low cost physical cleaning processes. Fine coal processing is a major problem for the industry, both through the cost of disposal of reject fines and through the mining cost of lost coal values. Of the available disposal methods, impoundment has always been the most popular. In many cases, when the coal fines were of sufficient quality, froth flotation and expensive filtration methods were used to recover the coal in these waste streams. The coal fines are not always of a marketable quality, however, and flotation, due to poor yields and difficult dewatering, has always been an expensive and not necessarily profitable process. The oil agglomeration method is increasingly important as a technology for the treatment of fine coal-in-water suspensions. These fines can be preferentially wetted and agglomerated by many different oils mixed with the suspensions. Ash-forming impurities remain in suspension and are rejected when the agglomerates are recovered, for example, by screening. Agglomeration-based methods provide perhaps the only practical means for upgrading extremely fine coal to useful products on a large scale. As with froth flotation, oil agglomeration relies on differences in the surface properties of coal and impurities to effect separation. Whereas flotation be- comes less effective with particles finer than 200 mesh (0.075 mm) or coarser than 50 mesh (0.3 mm), there appears to be no lower limit on particle size for oil agglomeration while particles % in. (3.175 mm) diameter or larger can also be treated, if desirable. In addition to this ability to clean a broader size range of coal particles, oil agglomeration can produce a dense, coarse granular product of acceptable strength and low water content without the need for vacuum or thermal drying. The preferential wetting of solid surfaces by immiscible liquids has been utilized, if not fully understood, for a long time. Indeed Gaudin,229 in tracing the ancestry of froth flotation, refers to a 15th century oil-pulp kneading procedure in which water-wetted particles were freed under water from an oiled mass. An understanding of the physical chemistry involved in such

Jan 1, 1991

By TONY CICINELLI

INTRO PAGE

Jun 13, 2021

By Richard B. Muter

In determining the layout or combination of unit operations to be utilized in a modem preparation plant, several factors must be taken into account. Among these are the washability data, size consist data, the particular market or markets for the coal, the mining method used, the degree to which the coal must be prepared, expected fluctuations in raw coal and markets, and the overall economics of the process. In addition, there are the health and safety aspects of coal utilization and preparation. Chapter 1 of this book discusses the characteristics of coal and coal markets, while Chapter 2 deals with the design of preparation plants. Once the unit operations for a particular plant have been decided upon, these arrangement may be depicted by using a flowsheet. A coal preparation plant flowsheet is a two-dimensional graphical representation of the sequence of operations, the arrangement of machinery, and the flow of materials for a particular coal cleaning operation. The flowsheet is usually qualitative in nature, becoming more quantitative as material balances, water balances, numbers and sizes of various pieces of equipment, etc. are added. The usual convention in preparing a flowsheet is to show the feed flowing from left to right, starting at the top left and working down as in an all-gravity process. Various symbols are used for each unit operation as depicted on a flowsheet, and Fig. 14-37 is a compilation of the commonly accepted international standard symbols for each unit operation. Fig. 14-38 through Fig. 14-40 are flowsheets of various coal cleaning processes as published in the January 1976 issue of Coal Age. Each process has its own unique features which, among others, depend upon the coal being cleaned, the coal market, and the mining operation. Fig. 14-38, for example, is a flow diagram for a jig plant preparing steam coal from two strip mines located a few miles apart. In addition to the jig washer, cyclones are used to treat the finer size coal. Fig. 14-39 is a flowsheet of a heavy media plant using a heavy media washer for + %-in. (+6.3-mm) coal, froth flotation for -28 Tyler mesh (-0.6 mm) material, and dewatering phase units (dwp) for Y, in. x 28 Tyler mesh (6.3 x 0.6-mm) cleaning of steam coal. In addition, thermal drying, centrifuge drying, and the use of vacuum disk filters and thickeners for dewatering are depicted. Fig. 14-40 is a flowsheet of a plant producing metallurgical coal. In addition to the heavy media and froth flotation circuits, a tabling circuit is also employed. These flowsheets are intended to give the reader an example of how the various unit operations for coal cleaning may be linked together. Figs. 14-41 and 14-42 illustrate the conversion of block diagrams into an IS0 prescribed set of symbols.

Jan 1, 1991

By Chris Lynagh, Lisa Smiley

INTRO PAGE

Jun 13, 2021

By Joseph W. III Leonard

Most material balances on coal preparation plant flow diagrams are stated in tons per hour of solids and gallons or liters per minute of water. Balances expressed in these terms can be simplified when it is known that 4 gpm (15.1 L/min) of water is about equivalent to 1 tph (0.9 1 thr) of water. Some useful relationships follow

Jan 1, 1991

By Stephen Njoloma, Amitabha Mukherjee

INTRO PAGE

Jun 13, 2021

By David G. Chedgy

Noise control is an important consideration in the design and operation of coal preparation plants. It is essential to understand and control noise sources to provide a safe environment for operating personnel. The average noise exposure levels in a typical coal preparation plant generally range between 95 and 100 db. An operator should not be exposed to noise levels of this magnitude for more than 4 and 2 hr, respectively, according to MSHA (Mine Safety and Health Administration) regulations. The major noise sources in a coal preparation plant include noise from impacting the inside surfaces of steel chutes, vibrating screens, coal crushers, pumps, motors, fans, and blowers. The magnitude of noise varies considerably from one situation to another. NOISE EXPOSURE IN COAL PREPARATION PLANTS Noise regulations established by the Occupational Safety and Health administration (OSHA) are accepted by MSHA relative to caal preparation plants. Fig. 14-43 shows a graph of the time of noise exposure in hours per day to which a worker can be exposed for each A-weighted sound level. According to this graph, a worker is permitted to spend 8 hr in a 90-db noise environment, but that time must be halved when the A-weighted sound level increases 5 db. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the length of time he is permitted to spend in that environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: where C is the actual duration of exposure at a given steady state noise level and T is the noise exposure limit for the level present during the time C According to MSHA regulations, the dosage, D, should not exceed one (1) for any worker for a full day of work. As an example of typical plant noise levels, vibratory screens and crushers emanate noise levels in excess of 90 db at a distance of 3 ft (0.9 m) with no material flow. With material flow, noise level increases 1 to 10 db depending

Jan 1, 1991

By Will Hodder, Martin Mancini

INTRO PAGE

Jun 13, 2021

By Richard B. Muter

1. Coal Preparation Terms (General) 1.1 Coal preparation-collectively, physical and mechanical processes applied to coal to make it suitable for a particular use. 1.2 Run of mine (ROM coal)-coal produced by mining operations, before screening, crushing, or preparation. 1.3 Raw coal-coal that has received no preparation other than possibly screening or crushing. 1.4 Raw coal feed-raw coal supplied to a plant or machine, in which it undergoes some form of preparation. 1.5 Coal cleaning-the treatment of coal to lower the mineral matter content (ash). 1.6 Cleaned coal; clean coal-coal produced by a cleaning process (wet or dry). 1.7 Middlings-a product of coal preparation that, by reason of its ash content, is intermediate between coal and discard. It follows therefore that the relative density of middlings is intermediate between those of coal and discard. Middlings may be reprocessed. 1.8 True middlings; bone comparatively high ash particles so nearly homogeneous that their quality cannot readily be improved by crushing and recleaning. 1.9 False middlings; interbanded middlings-middliigs in which the particles consist of bands of coal and shale, and from which the coal may be liberated by crushing 1.10 Refuse-waste material in the raw coal which the cleaning process removes. (See also discard; dirt; stone, No. 1.12). 1.1 1 Reject-the material extracted from the feed during cleaning, for retreatment or discard. 1.12 Discard; dirt; stone--the material extracted from the raw coal and finally discarded. 1.13 Recirculation-the operation in which the whole or part of a product from a process is returned to the feed to the process, e.g., the return of the crushed overflow from a screen to the screen feed for rescreening. 1.14 Foreign coal-coal received at a preparation plant from a colliery other than that to which the plant is attached. 1.15 Imported coal-coal coming from a foreign country, or other state within the country. 1.16 Low-grade coal combustible material that has only limited uses owing to undesirable characteristics (eg., ash content or size). 1.17 Segregation-partial separation of a previously mixed material into its constituents, occurring as a result of differences in either particle size or relative density. 2. Cleaning Characteristics 2.1 Washability-amenability of coal to improvement in quality by cleaning. 2.2 Float-and-sink analysis-the division of a sample into relative density fractions with defined limits, the proportions of the fractions being expressed as percentages of the total sample, commonly with an indication of the ash percentage (and other characteristics, if required) of each fraction.

Jan 1, 1991

By Jesse Salai, Colin Sessions

INTRO PAGE

Jun 13, 2021

By John H. Weigand, Stephen V. Crum

"VIBRONICS, INC. instrumented and monitored a residential structure for response to,blasting at aMidwestern surface coal operation. The residence was owned by the mining company and was extremely close to the operation. Blasting was conducted within 120 feet (36.5 meters) of the test structure. Up to seventeen (17), four (4)-channel seismographs were used during the monitoring period. The basement walls and floor were monitored. VIBRONICS, INC. also monitored a brick chimney in the basement and attic. Structural responses were then compared to outside vibration measurements taken in the soil near the foundation."

Jan 1, 1998

The question of earth models has repeatedly arisen in our work. An accurate representation of the seismic properties is required for three reasons: 1.To be able to determine from a set of received arrival times, the location of a seismic source in the earth, and secondly the degree of accuracy required in the model used for calculating source location from the set of arrival time differences. 2. To be able to determine the expected arrival times at an array of geophones produced in response to a hypothetical source in the earth. 3. To be able to estimate received signal strengths more accurately. The work reported here on earth models is based on information from sever- al consultants and from others who expressed an interest in the problem and supplied information to us. II. COAL MINE GEOLOGY On one of our earlier assignments for the Bureau of Mines, Earth Science Research Inc. of Cambridge, Massachusetts prepared for us a short description of the lithology to be expected at coal mine sites. This description follows, together with the ranges of compressional seismic velocities (Figure I*) associated with typical materials comprising the layered structure of a coal mine area. Coal is primarily associated with fresh water sediments including sandstones, shales, and clays, and occasionally may be metamorphased to varying degrees. In the Appalachian Basin the coal beds occur within cyclical sequences of non-marine shales, sands tones, conglomerates, limes tones, and clays. The beds range in thickness from a few inches to 60 feet, averaging between 2 feet and 10 feet. They have generally broad areal extent, occasionally up to 5,000 square miles, and have an overall tabular or lens-like shape. Within a particular lens, local changes in thickness are normal.

Jan 1, 1974

During the first quarter of 1973 ADL worked closely with PMSRC staff, under an extremely compressed time schedule, on all aspects of the detailed planning, organization and overall coordination and preparation of the lectures and in-mine demonstrations for the Bureau's Technology Transfer Seminar on Mine Communications given in March of 1973 to representatives of the mining industry. Our efforts centered on the detailed organization and preparation of each of the five technical seminar lectures and associated supporting material, and the coordination of tasks assigned to ADL and other seminar participants. Revised and expanded drafts of the seminar papers were prepared from rough draft versions obtained from PMSRC, Collins Radio and ADL staff. Measurements were made to gather key data on the operation and performance of each of the following systems installed in the Bruceton Safety Research Mine; call alert paging, roof bolt paging, section wireless radio, and guided wireless radio systems. These data were analyzed, manufacturer's equipment specifications utilized, and calculations made to provide performance curves and data for each of the above systems. A substantial amount of artwork was conceived and prepared for 35 m slides, system identification posters in the mine, and seminar handouts. This artwork included some forty 8-1/2" x 11" line sketches, graphs, block diagrams, circuit diagrams, coverage maps, and other line drawings; five 30" x 40" block diagram system identification posters suitable for in-mine use; a 20" x 30" detail perspective illustration of a representative coal mine layout; forty viewgraphs; and seventy 35 m slides of the artwork and word charts. Conferences, discussions and review sessions were held with conference participants to help coordinate the various efforts, obtain technical information, and make final plans regarding the lecture presentations, associated visual aids, and the communication system installations to be demonstrated in the Bruceton mine. These meetings included final systems checkouts and dry run presentations and reviews of the lectures and mine demonstrations. This phase of the seminar effort concluded with R. Lagace and R. Spencer of ADL participating in two days of seminar presentations in the lecture hall and in the Bruceton mine.

Jan 1, 1974

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974

Crosson and Peters treat the errors that result in miner location due to errors in the overburden earth model used for computing location. A parallel effort by J. Powell of PMSRC is discussed here, where the location method used is that of the Westinghouse location program - "Miner". This location program was tested by Powell by using arrival times generated from the overburden earth model of Table l* rounded to the nearest millisecond. Location computations were then made using 3 geophones at a time. The average location is tabulated for all geophone triplets except when 3 geophones are in line. Geophone arrays were as shown in Tables 2 and 3. The manner in which the test was done is illustrated in Figure 1. I. SUMMARY OF RESULTS The arrival time differences, based on the Table 1 earth model, together with geophone locations based on the array geometries of Tables 2 and 3, were entered into the computer, together with a stated depth of 700 feet and an estimated overburden seismic velocity of 10,000 feet per second. These parameter values were processed by the location program - "Miner". Figure 2 illustrates the interpretation of the plots and data. The tabular data and plots of Table 4 and Figures 3, 4, and 5 illustrate the location error results obtained. These plots indicate that for sources within the array, the errors are considerably less than the measured errors obtained during field tests of the present location system. The possible reasons for this discrepancy are noted in Part Eight (Earth Models).

Jan 1, 1974

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

By Clément F. Bernier

One of the chief sources of the world's supply of asbestos lies in a belt of ultrabasic rocks which runs northeastward through an area called the Eastern Townships, south of the St. Lawrence River in the Province of Québec. The productive portion of this belt extends from the town of Asbestos in the south, for a distance of some 9,5 km to beyond the village of East-Broughton. The first discovery of asbestos in this region was made in 1874. Only crude fibre was produced until 1888 when the first mill was erected near the town of Black Lake. Since the inception of the industry, almost 100 years ago, no less than 100 different compa¬nies have been formed and 46 different mines have been operated. There are presently 5 active companies in the area providing direct employment for 4100 workers, down from 6000 during the seventies.

Jan 1, 1984

By John C. McDonald

CONTROLLED cold work is used between solution heat treatment and precipitation heat treatment for producing certain tempers of the commercial aluminum base alloy 2219 (designation of the Aluminum Association, U.S.A.) which contains 6.3 pet Cu as the major ingredient responsible for the age hardening. The complete composition limits for this alloy are listed in Table I. The alloy has been described in detail,' and the control of the heat treatment has also been published.2 Beneficial effects of such cold work in other alloys have also been pointed out.3'4 NO data have been published on the effects of varying amounts of cold work under fixed aging conditions. In connection with an investigation of the possibility of providing the desired cold work by explosively generated shock waves, it became desirable to investigate the effect of variable cold work, and to compare the re -sults with those obtained from explosives. The general principles of explosive hardening are well-described in the literature.' All material used was guaranteed by the supplier

Jan 1, 1968