Search Documents

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of "boom" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.

Jan 1, 1925

"No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of ""boom"" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.A technical discussion of the ore occurrence and mining operations in the camp will be the subject of a paper to be read before this meeting of the Institute. The mission of this article is to supply a ""Baedeker"" where Baedeker is lacking.The town of Park City is a typical, up-to-date, western mining camp which owes its existence as a town of 4,500 inhabitants solely to the mining industry. The camp is located 7,000 feet above sea level, thirty-two miles east of Salt Lake City. It is situated on the Victory Highway seven miles from its junction with the Lincoln Highway and has the benefit of excellent automobile communication with the metropolis of the state. Both the Denver and Rio Grande and the Union Pacific Railroads give daily train service to the camp and effectively solve the transportation problems of the mining companies."

Jan 1, 1925

By P. C. Kapur

The hierarchical relationship between three broad kinds of grinding models for a spatially homogeneous, linear, time-invariant batch grinding system are first established. Limiting and asymptotic arguments for arriving at approximate but simpler models are employed in all three cases. These parsimonious models -provide alternate and, in some respects, more incisive and convenient tools for the analyses of grinding processes and simulation of comminution circuits. In the discrete-size, discrete- time class of models, a reduced mill matrix is derived, which is seemingly adequate for those grinding circuits whose identification otherwise is difficult because of limitations on the quantity of data and its quality. In discrete-size, continuous-time types of models, parameter lumping has been employed for obtaining a G-H solution which is quite accurate and exceptionally useful for graphical display of data, model verification, and parameter estimation and simulation. In continuous-size, continuous-time models, a similarity transformation is used for solving the integrodifferential equation of grinding. This solution provides a unified framework for a number of apparently diverse empirical grinding phenomena such as self-preserving behavior of ground particle size distributions and energy laws.

Jan 1, 1987

"Many advances in glass technology and processing are being made and the possibilities for glass as a material in the future appear unlimited. Float glass, glass-ceramics, high-strength sheet and container glass, glass-reinforced plastics, glass for electronic equipment, aerospace glass, glass fibres, glass vehicles, glasses with selective-reflective coatings and glare-reducing glasses, to name a few, provide areas of significance at present and for the future. There appear to be great opportunities, in certain localities of Canada, to develop new sources of raw materials for an expanding Canadian glass industry.New developments in the structural clay products industry have centered around facing brick as a structural load-bearing material, prefabricated brick panels, large-sized units, isostatic pressing of sewer pipe and auto-matic settmg of brick. Fast-firing techniques, using prefired or calcined raw materials, and the development of high-strength products will result in the use of a wider range of raw materials in the whiteware and structural clay products industries.Porcelain enamel, a material used for many years in domestic appliances and for sanitary ware, now is used extensively in architecture, agriculture, water tanks, highway signs and reflectors, and in products where resistance to corrosion-plus-temperature is important. Exotic composites of ceramics and metals, and specialized ceramic coatings applied on metals by various techniques such as flame spray, plasma jet, or vapour and chemical deposition have proved useful in materials for aircraft power plants, rockets, missiles and nuclear applications."

Jan 1, 1967

By Joseph Matoney, B. K. Parekh

INTRODUCTION The term "dewatering" refers to removal of water from coal. Water associated with coal can be categorized as "free or surface" and "inherent or chemically bound" moisture.' The free moisture is found on the surface of coal, in capillaries and small spaces between two or more particles. The inherent or chemically bound water is found in the interior of the coal and as part of coal structure. A significant amount of free moisture can be removed by mechanical dewatering techniques. However, inherent moisture can only be removed by applying energy intensive techniques, e.g., direct or indirect heating. Moisture in the coal offsets some of the benefits of coal cleaning. Extra water in clean coal adds to extra cost in transportation, heat lost during vaporization, and plugging of chutes. From a utility perspective, a 1 % increase in moisture can offset a 4.5% decrease in ash.2 Mechanical dewatering can be classified into two major process categories according to the principles involved, namely, 1. Sedimentation-liquid is constrained and particles move freely. 2. Filtration-particles are constrained by a medium and the liquid flows through. Each of the process categories is composed of various separation techniques shown in Fig. Equipment currently being used by the mechanical dewatering of coal of varying size ranges and final moisture content is illustrated in Fig. 8-2. This figure indicates that sizes larger than 13/, in. (37.5 mm) present no particular dewatering problem. Shaker screens of the very crudest types and designs are capable of producing these sizes at low surface moistures. High-speed vibrators are used for the intermediate sizes and can be used for smaller sizes down to 0.02 in. (0.5 mm) if high moistures (15% surface moisture or greater) can be tolerated in the product. Usually, however, the vibrator is not used below 3/, to 3/, in. (9.5 to 6.3 mm) because of the moisture associated with these fine sizes. At this level, centrifugal force is usually employed to aid dewatering. Centrifuges of various types and designs are used practically

Jan 1, 1991

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or bookkeeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. The emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1959

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or book- keeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. T he emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1964

By S. D. Strauss

The marketing of nonferrous metals and of the ores and concentrates from which these metals are recovered is a fascinating trade, international in character, sensitive to every change in the economic tide, and complex in its organization. Each individual metal has its own marketing mechanism; no two are exactly alike. The differences sometimes are a matter of tradition rather than of necessity, but usually they have developed because of the very nature of the problems of producing or consuming the individual metal. This description, because of limitations of space, can do no more than indicate the major aspects of the trade and touch lightly on the marketing structure of each metal. The dictionary states that a market is a "meeting of people for selling and buying." In the case of nonferrous metals this meeting may occur on a half-dozen different occasions between the time the ore has been first mined and the time the refined metal is available for use by industry; or it may not occur at all until after the metal itself has been rolled, drawn, stamped, cast, or forged into a useful semifabricated shape. To illustrate: A Chilean miner may sell his small ore production to a custom mill, which produces concentrates that are sold to an ore dealer, who finances the shipments of the concentrates to a United States custom smelter, which buys these' concentrates for conversion into blister, which is subsequently refined into electrolytic copper and sold. Conversely, much of the production of aluminum is in the hands of integrated concerns that mine bauxite, convert bauxite to alumina, smelt the alumina to produce aluminum, and then fabricate the aluminum into semifinished or even finished products before title to the material changes hands for the first time. Some nonferrous ores are not converted into metal at all but are sold by the miners or dealers directly b the ultimate consumers. A good example would be chrome ores used by the chemical industry. And of course a substantial part of the commerce in nonferrous metals is in scrap, which is the reconversion into useful form of metals that have long since been mined and smelted. Thus, one-third of all the lead used in the United

Jan 1, 1959

By S. D. Strauss

The marketing of nonferrous metals and of the ores and concentrates from which these metals are recovered is a fascinating trade, international in character, sensitive to every change in the economic tide, and complex in its organization. Each individual metal has its own marketing mechanism; no two are exactly alike. The differences sometimes are a matter of tradition rather than of necessity, but usually they have developed because of the very nature of the problems of producing or consuming the individual metal. This description, because of limitations of space, can do no more than indicate the major aspects of the trade and touch lightly on the marketing structure of each metal. The dictionary states that a market is a "meeting of people for selling and buying." In the case of nonferrous metals this meeting may occur on a half-dozen different occasions between the time the ore has been first mined and the time the refined metal is available for use by industry; or it may not occur at all until after the metal itself has been rolled, drawn, stamped, cast, or forged into a useful semifabricated shape. To illustrate: A Chilean miner may sell his small ore production to a custom mill, which produces concentrates that are sold to an ore dealer, who finances shipments of the concentrate to a custom smelter, which buys them for conversion into blister, to be subsequently refined into electrolytic copper (sometimes by a refinery having no corporate ties with the custom smelter) and sold. Conversely, aluminum production is mostly by integrated concerns that mine bauxite, convert it to alumina, smelt that to produce aluminum, and then fabricate that into semifinished or even finished products before title to the material changes hands for the first time. Some nonferrous ores are not converted into metal at all but are sold by the miners or dealers directly to the ultimate consumers. A good example would be chrome ores used by the chemical industry. And of course a substantial part of the commerce in nonferrous metals is in scrap, which is the reconversion into useful form of metals that have long since been mined and smelted. Thus, one-third of all the lead used in the United

Jan 1, 1964

By Carroll C. Bailey, William F. Boericke

Mine financing, or providing adequate capital for developing and bringing a mining property into production, is an essential requirement for a successful operation. Today it presents a different picture than even twenty-five years ago. The day appears to be gone when a mining property could pay its own way from grass roots to production. The country has been quite thoroughly combed for surface showings from which sufficient initial profit could be immediately garnered to pay for further development and production facilities. The four M's for success in mining-mineral, market, management, and money-are still essential; but doubled or tripled wage costs and steep advances in cost of equipment and supplies throw increased emphasis on adequate capital funds for bringing in a prospect and making it a producer. Consequently, the old picturesque, although seldom rewarding, grub- staking procedure where a single venturesome citizen might advance funds to a prospector on a fifty-fifty basis for whatever discovery he might find, has largely disappeared. Its place, to some degree, has been taken by the small syndicate of venturesome members who band together for furnishing funds to a group of prospectors for the same general purposes. Such a syndicate has a definite organization and is usually assured of sufficient initial funds, or flow of funds, to carry on work for several years. It is headed by an engineer-promoter who has had considerable field experience as well as personal knowledge of his prospecting crews. For the owner of a potential mining property who has ample capital, the problem is to determine (1) justification for the necessary investment in exploration and development, and (2) the economics of the enterprise as to size and degree of integration of the final operating entity. If the owner of such a property has little or no capital, he also faces these same basic problems but, in addition, must be able to present the findings of fact and persuade the prospective investor that the enterprise will produce

Jan 1, 1959

By Andrew Bursey, Colin Lyons

INTRO PAGE

Jun 13, 2021

By Sebastian Sucri, Percy Townsend

INTRO PAGE

Jun 13, 2021

By Dave Dorfman, Ben DiFiore

INTRO PAGE

Jun 13, 2021

By David Watson, Steve Price

INTRO PAGE

Jun 13, 2021

By Luis Fernandez-Deza, Kaveh Talebi, Seth Pollak, Soto Vardakos

INTRO PAGE

Jun 13, 2021

By Anton Hupfauf, Peter Raleigh

INTRO PAGE

Jun 13, 2021

By Mohamed Younis, Keith Ward

INTRO PAGE

Jun 13, 2021

By Mike Stolkin, Julio Martinez

INTRO PAGE

Jun 13, 2021

By Aaron McClellan, Eric Levonas

INTRO PAGE

Jun 13, 2021