Search Documents

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air-pressure drop p in. water gauge across the airshaft. † The airshaft pressure drop is calculated by the formula: R X l X O X Q2 P= 5-2 X A3 wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: w= 0.746Q X P 6345 With a combined over-all unit efficiency of the fan and drive of E per cent, the air-shaft power requirements become W = 100w There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C¢ per kw-hr. the annual airshaft power cost MI dollars per year becomes: M1 = 87.60W X C which, expressed by the component parts, becomes: M1 V 5.2X4' / XQ Z 0.746 X 100 X 87.60 X C V 60 X E ) The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available molletary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air-shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1947

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air-pressure drop p in. water gauge across the airshaft. † The airshaft pressure drop is calculated by the formula: R X l X O X Q2 P= 5-2 X A3 wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: w= 0.746Q X P 6345 With a combined over-all unit efficiency of the fan and drive of E per cent, the air-shaft power requirements become W = 100w There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C¢ per kw-hr. the annual airshaft power cost MI dollars per year becomes: M1 = 87.60W X C which, expressed by the component parts, becomes: M1 V 5.2X4' / XQ Z 0.746 X 100 X 87.60 X C V 60 X E ) The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available molletary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air-shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1947

By A.S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. Temperatures and Underground Waters Surface Temperatures.—The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the downcast shafts; however, the variation between winter and summer causes a difference of only 2" to 3" in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.—Rock temperatures on the deeper levels of the mine are as follows:

Jan 1, 1940

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. Temperatures and Underground Waters Surface Temperatures.—The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the downcast shafts; however, the variation between winter and summer causes a difference of only 2" to 3" in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.—Rock temperatures on the deeper levels of the mine are as follows:

Jan 1, 1940

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By F. C. Sturges

For some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are, solved. Recently we have completed two 36-in. diam core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam shafts were considered, but actual computations showed 36-in. diam shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could .be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1949

By G. S. Jenkins

The statistics set forth by Professor Mitchell in a proceding paper very carefully brought out the points that indicate that a marked amount of consideration must be given to" the haulage problem to adapt it to local conditions as encountered. Professor Mitchell's paper showed a spread of from 10 tons per man to 50 tons per man on the production crews, which spread can be recognized as entirely too large when one considers that the product is being sold at a price within very close limits. While a portion of this spread may be explained by different methods in cost accounting as to what employees are applicable to the production crew, it cannot all be blamed on an accounting method. A good portion must be explained by the improper application of equipment to the needs incurred by the local conditions. It is in an endeavor to go into this phase that this paper is given. It will be necessary to qualify the points covered in order to keep the subject from becoming too wide in scope. Along this line, conditions will be only those involved in bituminous coal mine practices and only the haulage of coal that is loaded with mobile loading machines in seams 4 ft thick and better. Haulage Methods Employed The Consolidated Coal Co. (Illinois) has been operating on a modernized basis for about 20 yr. By modernized we mean the loading of coal with mobile loading equipment. In review of haulage methods, it must be remembered that the main line electric haulage locomotive has been in service for some 40 or jo years. To augment this main line haulage, the mule did a quite satisfactory job during hand-loading days, but was later replaced by the gathering locomotive, either battery or cable-reel operated. This type of haulage was the method in common use at the time the mechanical loading of coal became of major importance and the success or failure of loading machine installations may be largely accredited to haulage facilities in the early days; that is, in the period around 1930. The Consolidated Coal Co. had its struggle with this problem beginning in about 1927 or 1928. We were somewhat fortunate in that we were already using gathering locomotives powered by storage batteries at the time we introduced mechanical loading. This meant that we did not have to spend as much time training motormen and trip riders as many mines did that utilized only mules for their secondary haulage. This was all advantage, and our efforts could be focused on ways and means of providing adequate car service to the loading machine. Like most operations, we endeavored to gear the car service to the capacity of the machine, with a large crew endeavoring to load the maximum tonnage that the machine would handle. Toward that end our first move was to install switches

Jan 1, 1949