Search Documents

By J. N. Hummel

The methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view. The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic. It is obvious that methods based on such a simple principle and capable of solving directly many of the practical problems of mining geology have found a widespread application. However, these methods are unable to furnish any information as to the presence, depth and physical properties of layers in the underground, which have different conductivities, but are parallel, or only slightly inclined, to the surface. Where such conditions exist in the underground, the picture of the field

Jan 1, 1932

By Karl Sundberg

ElectRical investigations carried out in regions containing sedimentary rocks showed that sediments generally are good electrical conductors, a fact which at the present time is used for structural investigations by electrical methods. It is of fundamental importance, not only for these investigations but also for electrical prospecting in general, to know the electrical properties of various soils and rocks. It will be useful, therefore, to discuss this question with the hope that the general points of view discussed in this paper will perhaps be completed by further observations and determinations of material from various localities. This paper is based principally on the study of literature, and the purpose is primarily a discussion of the main factors that determine the electrical conductivity of soils and rocks. It will follow, however, that the factors discussed here also frequently decide how far a certain orebody can be regarded as a good electrical conductor compared with the surrounding rocks. All rocks are more or less porous, and the pores are filled with liquids and gases. Their electrical conductivity, therefore, depends on the following factors: 1. The electrical conductivity of minerals composing the rock. 2. Electrical conductivity of the liquid filling the pores. 3. Proportion of the volume of liquid filling pores of the rocks to the solid rock material. 4. Shape of the pores. 5. Arrangement of the particles of gas and liquids. 6. Temperature. Dry minerals, with the exception of certain ore minerals, are complete nonconductors from the point of view of applied geophysics; in the present investigation we deal with rocks which have no conducting minerals, and factor 1, therefore, is not important. The same is true of soils. The liquids contained in soils and rocks in most cases are waters, sometimes oil. As oil is a nonconductor of electricity, the impregnating waters will determine the electrical conductivity of soils and rocks.

Jan 1, 1932

By Irwin Roman

The literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years,' but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data.2 There seems to be a general reluctance among geologists and engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1932

By D. O. Ehrenburg, R. J. Watson

During the earlier period of electrical prospecting, the search for orebodies was by far the most important application of this method of geophysical prospecting. In the past few years, however, increasing attention has been paid to the possibilities of this method in the investigation of subsurface structures. Not only have fault zones been located, but attempts have been made to determine the depth to certain strata and thus contouring on some bed which proves to be a good "electrical marker." Many workers have published the results of field tests showing how their particular interpretations have agreed with the actual field conditions, but very few have stated their method of interpretation. Weaver, Hummel and Stefanesco and Schlumbergerl have given a more theoretical discussion of the resistivity methods. Hummel and Stefan-esco and Schlumberger have published mathematical solutions for the flow of electricity in a medium involving four layers. In this paper the authors present a solution for the flow of electricity in a medium of any number of horizontal strata. By means of this solution, curves showing the relationship between the apparent resistivity and the electrode spacing can be computed for ideal cases. Point-source in an Infinite Homogeneous Medium In resistivity measurements the current is conveyed to the earth by means of two electrodes, which can be mathematically treated as point-sources of equal and opposite strength. A point-source of strength I is defined as a point at which electricity is being generated at the constant rate of I coulombs per second, or I

Jan 1, 1932

By L. B. Slichter

After statement of the principles of similitude which apply to electromagnetic modeling, charts showing the inductive response of conducting spheres as dependent upon frequency, conductivity, and size are exhibited in this paper. The shape of the curve which relates intensity of response to frequency is significant in indicating the advisability of low frequencies in the exploration for conducting bodies, when consistent with the securing of a large percentage of the ideally possible response. Comparisons of theoretical response and that observed with models are shown, and relationships with the subject of applied electromagnetic prospecting are indicated. Maxwell Field Equations The Maxwell field equations summarize the physical laws that govern electrical field phenomena; they are the basis for the solution of electromagnetic problems. These concise equations, with adequately formulated boundary conditions, specify the complete electrical condition of continuous media, and the development of their solution amounts merely to a more convenient re-expression of phenomena already completely described. Thus, the immediate content of the field equations themselves is sufficient and sometimes convenient for the treating of certain questions (such as those relating to electromagnetic models) which are independent of the special factors of geometry, or the nature of an impressed field. The four Maxwell field equations are written below, in c.g.s. gaussian units: curl E = -B/c [21 div eE = 4pp [31 div B = 0 [41

Jan 1, 1932

By Paul A. Schafer

BaLatoc mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.' The region is a deeply dissected plateau, ranging in altitude from 3000 to 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. I): 96, 231 and 364, which strike about N.70°E. and dip 50° to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.4s°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to. east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. Northeast Faults The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on On fault and 96 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar NO. I, and Sun

Jan 1, 1949

By Paul A. Schafer

BaLatoc mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.' The region is a deeply dissected plateau, ranging in altitude from 3000 to 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. I): 96, 231 and 364, which strike about N.70°E. and dip 50° to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.4s°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to. east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. Northeast Faults The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on On fault and 96 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar NO. I, and Sun

Jan 1, 1949

By Wilson D. Michell

The Magma copper vein trends east-west, dips 70" south, and cuts through a 6000-ft thickness of limestones, quartzites,. shale, diabase, and schist. The vein is itself a fault with a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facitliate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, 2nd mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine. Introduction This paper describes an example of geological work applied directly to mining and exploration problems in a deep vein deposit, and it is presented as being of interest especially to those engaged in working more or less similar veins. In 1944 to 1945 the writer spent a year as assistant to J. K. Gustafson in a thorough geological examination of the Magma mine. Much of the writer's subsequent independent work described in the present paper had its inception in ideas originated by Gustafson during that examination. Objectives of Geological Work at Magma Mine The objectives of geological work at Magma, as at operating vein mines of a similar nature, can be summarized as follows: 1. Direct assistance to the mining department by means of predictions as to the size, shape, grade, and location of ore bodies; by solution of fault problems and irregularities in the veins; by prepara-?ion of detailed ore-reserve estimates in specific areas; by keeping a complete record of the geology and assay results in the mine; and by guiding development work. In short, geology can aid in the realization of the prime purpose of the mining department, which is that of producing the greatest amount of ore in the most economical and expeditious manner possible. 2. Guidance for exploration, especially diamond drilling, in undeveloped areas of the mine. 3. Contributions to the understanding of the general geology of the deposit and its regional setting, including ore genesis, structure, and mineral relationships. Magma Ore Deposit The east-west trending Magma vein, dipping about 70" south, cuts through a 6000-ft thickness of concordant limestones, quartzites, shale, diabase, and schist, named in descending order. These

Jan 1, 1949

By Wilson D. Michell

The Magma copper vein trends east-west, dips 70" south, and cuts through a 6000-ft thickness of limestones, quartzites,. shale, diabase, and schist. The vein is itself a fault with a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facitliate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, 2nd mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine. Introduction This paper describes an example of geological work applied directly to mining and exploration problems in a deep vein deposit, and it is presented as being of interest especially to those engaged in working more or less similar veins. In 1944 to 1945 the writer spent a year as assistant to J. K. Gustafson in a thorough geological examination of the Magma mine. Much of the writer's subsequent independent work described in the present paper had its inception in ideas originated by Gustafson during that examination. Objectives of Geological Work at Magma Mine The objectives of geological work at Magma, as at operating vein mines of a similar nature, can be summarized as follows: 1. Direct assistance to the mining department by means of predictions as to the size, shape, grade, and location of ore bodies; by solution of fault problems and irregularities in the veins; by prepara-?ion of detailed ore-reserve estimates in specific areas; by keeping a complete record of the geology and assay results in the mine; and by guiding development work. In short, geology can aid in the realization of the prime purpose of the mining department, which is that of producing the greatest amount of ore in the most economical and expeditious manner possible. 2. Guidance for exploration, especially diamond drilling, in undeveloped areas of the mine. 3. Contributions to the understanding of the general geology of the deposit and its regional setting, including ore genesis, structure, and mineral relationships. Magma Ore Deposit The east-west trending Magma vein, dipping about 70" south, cuts through a 6000-ft thickness of concordant limestones, quartzites, shale, diabase, and schist, named in descending order. These

Jan 1, 1949

By W. H. Emmons

Many mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and, many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement. Introduction When faults are followed along dip or strike, many of them are found to have curving or warped surfaces, and cross sections through them in most directions show sinuous or waving intersections. Openings are formed where one wall moves away from the other (Figs. I,2). Where there is a bend in the fault, movement in any directions except along the axis of the bend will

Jan 1, 1949

By W. H. Emmons

Many mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and, many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement. Introduction When faults are followed along dip or strike, many of them are found to have curving or warped surfaces, and cross sections through them in most directions show sinuous or waving intersections. Openings are formed where one wall moves away from the other (Figs. I,2). Where there is a bend in the fault, movement in any directions except along the axis of the bend will

Jan 1, 1949

By Carlton D. Hulin

The usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma facies are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacemerit and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district. The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 Per cent may Occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible. Introduction A proper understanding of the causes that have localized our mineralized districts should be of considerable value to geologist and engineer alike. under current conditions the known ore reserves of productive mining camps are being rapidly depleted. Although ore of the future will be derived in part from deposits now known and from Ore bodies that are still to be discovered within the limits of productive mining districts, in part at least it must come from mineralized districts whose existence or importance yet remain to be recognized. The mining geologist is thus faced with two problems of paramount importance: (I) the location of new ore bodies within known mineralized areas and (2) the location of new mineralized districts within whose confines, previously unknown, valuable Ore deposits may occur. Any contribution to our knowledge concerning the causes for the localization of mineralized districts

Jan 1, 1949

By Carlton D. Hulin

The usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma facies are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacemerit and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district. The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 Per cent may Occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible. Introduction A proper understanding of the causes that have localized our mineralized districts should be of considerable value to geologist and engineer alike. under current conditions the known ore reserves of productive mining camps are being rapidly depleted. Although ore of the future will be derived in part from deposits now known and from Ore bodies that are still to be discovered within the limits of productive mining districts, in part at least it must come from mineralized districts whose existence or importance yet remain to be recognized. The mining geologist is thus faced with two problems of paramount importance: (I) the location of new ore bodies within known mineralized areas and (2) the location of new mineralized districts within whose confines, previously unknown, valuable Ore deposits may occur. Any contribution to our knowledge concerning the causes for the localization of mineralized districts

Jan 1, 1949

By J. C. McCarthy, J. B. Stone

At Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. Location The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in. the world. Another famous old silver district, Sombre-rete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo On on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is Surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. According to an account written in 1834 by Francisco Garcia, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between zacatecas and sombreretea Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active in 1751 under an administrator named Murguia, who left detailed notes describing them. In I757, however, the mines became inactive because of dificulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor Garcia had been aroused by the long disregarded notes of Murguia. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difliculties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven is pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1949

By J. C. McCarthy, J. B. Stone

At Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. Location The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in. the world. Another famous old silver district, Sombre-rete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo On on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is Surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. According to an account written in 1834 by Francisco Garcia, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between zacatecas and sombreretea Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active in 1751 under an administrator named Murguia, who left detailed notes describing them. In I757, however, the mines became inactive because of dificulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor Garcia had been aroused by the long disregarded notes of Murguia. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difliculties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven is pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1949

By Roland Blanchard

Recent discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Racecourse) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalco-pyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show Accepted Zonal Succession Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite Mount Isa Succession I In the main but prob- Silver sulphantimonides ably not wholly Tetrahedrite I contemporaneous Galena Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silver-lead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1475 ft.). The anomalous condition at Mount Jsa, both as to the unorthodox mineral succession and the largely unorthodox patteru of mineral distribution, is explained in the present paper,

Jan 1, 1949

By Roland Blanchard

Recent discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Racecourse) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalco-pyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show Accepted Zonal Succession Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite Mount Isa Succession I In the main but prob- Silver sulphantimonides ably not wholly Tetrahedrite I contemporaneous Galena Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silver-lead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1475 ft.). The anomalous condition at Mount Jsa, both as to the unorthodox mineral succession and the largely unorthodox patteru of mineral distribution, is explained in the present paper,

Jan 1, 1949

By Edward F. Fitzhugh

Quantitative appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies. Introduction When exploratory development of a mineral deposit is contemplated, three interrelated questions normally must be answered before a sound decision can be reached. How much will the program cost? How much will the anticipated ore add to the immediate value of the mine? And what is the chance of developing this ore? To justify development, the deposit should present a favorable disparity between the three factors, cost, chance and return. If, for example, there is a 50-50 chance of success, the ore that is sought should have an immediate worth (after deducting all subsequent charges that it must bear) of more than twice the cost of the development. Likewise, if the chance of finding the ore is but one in five, that ore should enhance the immediate value of the mine by more than five times the cost of developing it- With sound economic and operating assumptions, the cost of exploratory development and a present value of anticipated ore may be estimated within reasonable limits. Less general attention has been given to appraising ore chances in comparable terms. The exploratory experience of the mining industry is broad enough that knowledge, vision and judgment may be combined to yield more tangible evaluations of Ore expectancy than are now customary' A way of making such appraisals is suggested herein. The mathematics of probabilities cannot be applied directly to the search for ore. By coupling applicable principles of probability, however, with pertinent experience gained in mineral exploration, an estimate often can be made of the chance of finding a certain tonnage and grade of Ore in a specific location. Such estimated, or judged, expectancies for the several blocks of ground in a deposit may be combined in a simple chart to show the relationship of the various exploratory possibilities and the potential magnitude of the deposit' An engineer or geologist may find that the quantitative thinking required for an appraisal of this type is an aid in clarifying and coordinating his views and recommendations. For a person wishing to understand these views, an ore-expectancy

Jan 1, 1949

By Edward F. Fitzhugh

Quantitative appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies. Introduction When exploratory development of a mineral deposit is contemplated, three interrelated questions normally must be answered before a sound decision can be reached. How much will the program cost? How much will the anticipated ore add to the immediate value of the mine? And what is the chance of developing this ore? To justify development, the deposit should present a favorable disparity between the three factors, cost, chance and return. If, for example, there is a 50-50 chance of success, the ore that is sought should have an immediate worth (after deducting all subsequent charges that it must bear) of more than twice the cost of the development. Likewise, if the chance of finding the ore is but one in five, that ore should enhance the immediate value of the mine by more than five times the cost of developing it- With sound economic and operating assumptions, the cost of exploratory development and a present value of anticipated ore may be estimated within reasonable limits. Less general attention has been given to appraising ore chances in comparable terms. The exploratory experience of the mining industry is broad enough that knowledge, vision and judgment may be combined to yield more tangible evaluations of Ore expectancy than are now customary' A way of making such appraisals is suggested herein. The mathematics of probabilities cannot be applied directly to the search for ore. By coupling applicable principles of probability, however, with pertinent experience gained in mineral exploration, an estimate often can be made of the chance of finding a certain tonnage and grade of Ore in a specific location. Such estimated, or judged, expectancies for the several blocks of ground in a deposit may be combined in a simple chart to show the relationship of the various exploratory possibilities and the potential magnitude of the deposit' An engineer or geologist may find that the quantitative thinking required for an appraisal of this type is an aid in clarifying and coordinating his views and recommendations. For a person wishing to understand these views, an ore-expectancy

Jan 1, 1949

By Harrison Schmitt

The definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. we may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina, and probably soda and potash, are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations. Introduction The purpose of this paper is to define the terms commonly used in connection with the subject, to briefly review and discuss the broad features of the aureoles, to indicate some of the features lately recognized: to discuss the genesis, and to suggest how the associated ore deposits can best be studied and developed. When developing a subject in mining geology one is soon conscious of the vast amount of pertinent literature and that most relevant ideas, no matter how obscure, have been considered. One can only hope to make some small contribution in point of view, a few confirmatory observations, or, perhaps, suggest a small new idea indebted to the most recent data. It is nearly impossible, also, to give specific credit, and adequate credit, to all the contributors to a given subject. This study, furthermore, was not intended to cover the field exhaustively, nor is the bibliography complete. Definition OF Terms There is much confusion in the use of the broad terms concerned. Needless to say, metamorphism means change of form; metasomatism, change of substance. The term contact metamorphism, however, has been widely misused possibly by a majority of economic geologists and engineers. As originally adopted by European investigators it meant changes effected largely by heat (thermal effects) in the rocks invaded by plutonic intrusives, but did not include those local changes usually at the immediate contact brought about by the addition of substance, i.e., by metasomatism. The term has become clouded. In Europe it has

Jan 1, 1949