Search Documents

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,' or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

By E. H. Hamilton, H. C. Vacher

The limiting concentrations of carbon and oxygen which may CO-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation witch elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Hertyl.2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550" to 1600" C. and one atmosphere pressure. Kinzel and Egan % have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550" C. In order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume a value of 0.0102 at 1580" C. for this

Jan 1, 1931

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton's published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton's published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By T. I. Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook' and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946

By J. Brian Eby, T. I. Harkins

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook' and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By H. D. Wilde

At the Sugarland and Raccoon Bend fields in the Gulf Coast area, all wells are drilled with rotary tools and the casing is always set in cement that is placed by the circulation method. After the cement is set, the rotary mud that fills the hole is not withdrawn or bailed out; consequently, it is not customary to give the cementing job a direct test either by putting pressure on the hole to see whether the cement will hold or by observing whether an effective water shut-off is secured. About three years ago, this company started the practice of coring the cement left in the bottom of the casing and examining the core thus secured. If the core was hard and strong, the cementing job was judged a success but if the core was incoherent, soft, and crumbly, the job was considered a failure. Of course, there were intermediate types of cores and it was not always a simple matter from this examination to decide whether the job was a success or failure. After about two years, a summary of the core examinations that had been made indicated that of cementing jobs made at depths of 1000 ft. or less, 60 per cent.. were failures; of those between 1000 and 2000 ft., 80 per cent. were failures, and of those between 3000 to 6200 ft., 100 per cent. were failures. This sta,rtling table emphasized the need of the study of the conditions under which the wells were cemented and of adopting means to reduce the percentage of failures. In addition to these core tests, two wells gave direct evidence that the cementing jobs were not always successful. In one, a four-year-old well at Goose Creek, the casing was perforated, and when fluid was circulated some of the old cement wss brought to the surface. Most of it was powdery and the few chunks that were brought up were soft and crumbly. The other was a well at Raccoon Bend which during a blow-out brought a number of chalky, soft and crumbly pieces of cement to the surface. Suggested Explanations of Cementing Failures Efforts were made at once to explain the causes of these cementing failures. As all of the cements used were of a high grade and gave

Jan 1, 1930

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By John T. Norton

In recent years, the damping capacity of metals has come to be recognized as an important index of certain types of structural change. In a number of instances, this property has proved to be particularly sensitive, but insufficient work has been done to permit a general interpretation. There is considerable question at the present time as to just what factors are responsible for the internal dissipation of energy when a metal is carried through a cycle of stress, and these factors must be ascertained if the value of the damping method as a metallurgical tool is to be determined. Since internal stresses are among the chief causes of dissipation of internal energy, or damping capacity, it was thought that a study of the changes in damping during the recovery and recrystalliza-tion of a cold-worked metal might throw some light upon the subject, particularly if the damping changes were correlated with other properties that are better understood. Probably more work has been done on the recrystallization phenomena of alpha brass than on any other metal, so this was chosen as the material for the present investigation. Damping measurements on brass have been made by Förster and Köster.1 They showed that the annealing of a brass that had been cold-drawn to 50 per cent reduction produced a rapid fall in the damping, a flat minimum occurring at approximately the temperature of recrystallization. The damping remained at a low value until grain growth was well under way and then it increased rapidly with increasing grain size. Köster and Rosenthal2 continued the work in greater detail. They pointed out that the damping decrease does not correspond to the hardness drop but occurs at a lower temperature, suggesting that the relief or redistribution of internal stresses has a large effect while the actual recrystallization effect is small. They also show the increase in damping at the higher annealing temperatures. Their curves are reproduced in Fig. 1.

Jan 1, 1940

By John T. Norton

In recent years, the damping capacity of metals has come to be recognized as an important index of certain types of structural change. In a number of instances, this property has proved to be particularly sensitive, but insufficient work has been done to permit a general interpretation. There is considerable question at the present time as to just what factors are responsible for the internal dissipation of energy when a metal is carried through a cycle of stress, and these factors must be ascertained if the value of the damping method as a metallurgical tool is to be determined. Since internal stresses are among the chief causes of dissipation of internal energy, or damping capacity, it was thought that a study of the changes in damping during the recovery and recrystalliza-tion of a cold-worked metal might throw some light upon the subject, particularly if the damping changes were correlated with other properties that are better understood. Probably more work has been done on the recrystallization phenomena of alpha brass than on any other metal, so this was chosen as the material for the present investigation. Damping measurements on brass have been made by Förster and Köster.1 They showed that the annealing of a brass that had been cold-drawn to 50 per cent reduction produced a rapid fall in the damping, a flat minimum occurring at approximately the temperature of recrystallization. The damping remained at a low value until grain growth was well under way and then it increased rapidly with increasing grain size. Köster and Rosenthal2 continued the work in greater detail. They pointed out that the damping decrease does not correspond to the hardness drop but occurs at a lower temperature, suggesting that the relief or redistribution of internal stresses has a large effect while the actual recrystallization effect is small. They also show the increase in damping at the higher annealing temperatures. Their curves are reproduced in Fig. 1.

Jan 1, 1940

By George M. Fowler, F. E. Gregory, William M. Agar, Joseph P. Lyden

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By William M. Agar, F. E. Gregory, Joseph P. Lyden, George M. Fowler

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By F. E. Gregory, George M. Fowler, William M. Agar, Joseph P. Lyden

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By J. H. Nead, J. W. Halley

The new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the construction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attractive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately18, 27, 28, 29, 30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved. Properties Desired in Low-alloy Steel A distinction between the new low-alloy steels and the common alloy steels is that the latter are generally used in the heat-treated (that is, quenched and tempered) conditions, whereas the new low-alloy steels are not only not heat-treated but are not susceptible to heat-treatment in the ordinary sense of the term. In this lies one of their chief advantages. Their properties can be obtained in the as-rolled, air-cooled, or annealed condition, just as with mild plain carbon structural steel. There is no need for heat-treating. Such steels can be readily formed hot or cold, and their properties are not appreciably changed by hot

Jan 1, 1936