Search Documents

By Russell B. Dix

Laboratory column leach tests are used routinely to evaluate gold and silver ores for heap leaching. The tests are fairly straightforward. The ore to be tested is placed into an appropriately sized leach column. Then an alkaline cyanide solution is applied to the ore and the effluent solutions are collected. The effluent solutions are then put through a column of activated carbon to recover the gold and silver in solution. Zinc precipitation may also be used for silver ores or if the ore contains a significant amount of soluble silver in addition to gold. The length of the leach time in the tests is mainly a function of how quickly the precious metals are recovered from the ore. At the completion of the tests, the tailings are assayed and the recoveries determined from the calculated head grades. The amount of ore to be used for a test is partly a function of its crushed size. The coarser the size, the larger the sample size for the column. A typical small-scale laboratory column test on ore crushed to -12 mm (-0.5 in.) would usually be conducted in a 100- to 150-mm-diam (4- to 6-in.-diam) column 2 m (6.6 ft) in height, containing about 20 to 45 kg (44 to 99 lb) of ore. A comparable test on the same ore crushed to 50 mm (2 in.) would be conducted in a 200- to 300-mm-diam (8- to 12-in.-diam) col¬umn 2 m (6.6 ft) in height, containing about 80 to 200 kg (176 to 441 lb) of ore. Larger-scale tests can be run by increasing the column heights and diameters. Conducting larger-scale tests results in increased costs for sample procurement, preparation, and running of the tests. The additional data obtained from

Jan 1, 1989

By Glenn M. Boyce

This paper discusses the results of a laboratory testing pro- gram to determine the validity of hydraulic fracturing stress measurements in salt. Tests were performed on 15 cm diameter samples loaded under hydrostatic stress conditions to determine the influence of time, confining pressure, flow rate, borehole diameter, and packers on breakdown pressure. Tests were also performed in a polyaxial loading frame to determine whether or not hydraulic fracturing could be used to measure non-hydrostatic stresses. The test results indicate that the breakdown pressure is not affected by time delays of up to 64 hours between the application of load and fracturing the rock. Breakdown pressures were found to fall short of predicted elastic values at higher confining pressures for the hydrostatic tests. The ratio of the horizontal stresses in non-hydrostatic tests had no effect on breakdown pressures. Flow rate and borehole diameter variations were found to have a marked effect on breakdown pressures. Shut-in pressure values, which are generally used as an indication of the minimum stress value, exceeded the applied minimum stresses by 10 to 60% depending on the method of determination used. The lack of a relationship between breakdown pressure and horizontal stress ratio may preclude hydraulic fracturing from being used in salt as it is conventionally applied in brittle rocks.

Jan 1, 1984

By M. R. Geer, H. F. Yancey, P. S. Jacobsen

Two growing problems confront the preparation engineer-still further restrictions on stream pollution and a greater proportion of fine coal as more and more continuous miners come into use. The dewatering screens, centrifuges, and settling ponds that sufficed a few years ago must often be supplemented by more effective equipment, and in some instances the finest solids are now being recovered by vacuum filtration, once considered too costly in many coal washeries. Unfortunately not all slurries can be readily filtered. Some are virtually unfilterable, and others do not permit the high cake rates needed to hold costs within reason. Often, however, these difficult slurries can be rendered filterable by flocculation. Starch and lime have long increased settling rate in thickeners and can also aid filtration. More recently there have been other flocculants, primarily synthetic polymers or gums. Reports of their great effectiveness prompted the U. S. Bureau of Mines to test their use in filtration as part of its program on recovering and cleaning fine coal. The object of the present work was to compare some of the newer flocculants with starch and lime and to test the reaction of different types of slurries to flocculation. Three natural slurries, three synthetic coal-clay mixtures, and five flocculants were tested, all with a laboratory filter leaf.

Jan 7, 1959

By A. M. Johnson, M. A. Cornachione

The west central Upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur that can create emission problems when processed in a kiln. A low-cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated. In this study, optimal conditions for the bacterium Thiobacillus ferrooxidans were created to promote pyrite oxidation and, therefore, sulfur removal from the slate. Preliminary lab scale flask tests using crushed and sized slate (-40 + 100 mesh) and T. ferrooxidans bacteria in a sulfuric acid medium resulted in 70% oxidation of pyrite over a one-month period. Subsequent column leaching tests on coarser materials (-3/8+1/4 in.) operated for six months resulted in a maximum reduction of total sum of 75%. These data suggest that bio-heap leaching to remove sulfur from the slate for use as a kiln feed material is viable.

Jan 1, 1995

By M. A. Cornachione

The west central upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur which can create emission problems when processed in a kiln. A low cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated.

Jan 1, 1992

By Bo-Hyun Kim, Steve Berry, Mark K. Larson

"When coal pillar bursts occur, they involve the sudden expulsion of coal and rock into the mine opening. These events occur when relatively high stresses in a coal pillar, which serve as support in underground workings, exceed the critical capability of the pillar. This causes the pillar to rupture without warning. A cleating is a type of naturally occurring joint system unique to coal seams. However, cleatings are pervasive throughout the coal seam and are much more tightly spaced than joints occurring in other rock types. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated 84 coal samples obtained from a Utah coal mine by conducting both unconfined and triaxial compressive tests in order to examine the response to stress as a function of both confinement and orientation between cleat and loading direction. The results of the study show that the confining pressure dictated not only the peak compressive strength but also the brittleness as a function of the major-to-minor principal stress ratio. The spalling limit of the coal estimated by the s-shaped brittle failure criterion appears to be very dependent on the angle between the cleat and the loading direction, particularly at lower confinement.INTRODUCTIONCoal pillar bursts, or bumps, remain a most critical safety concern in underground coal mining, despite significant advancements in engineering controls. As shown in Figure 1, between 1983 and 2014, there were nearly 400 cases of reportable dynamic failure accidents in coal and nonmetal mines, resulting in 20 fatalities, 155 lost-time accidents, and an estimated 48,000 lost man hours (MSHA, 2015). These types of events have been documented for well over 100 years within the American underground coal mining industry. During this time, mining practices and support technologies have evolved considerably, resulting in an overall decrease in the rate of dynamic failure-related injuries and fatalities. Although techniques and practices of mining are highly advanced, coal pillar bursts, or bumps, continue to occur (Mark and Gauna, 2015). If coal is expected to fail in a brittle manner, behavior changes associated with relatively low tensile strength, such as the transition from tensile to shear failure, have to be considered and reflected in the adopted failure criteria. Rock failure in tension takes place at low confinement around excavations due to tensile failure in heterogeneous rocks (Diederichs, 2007). The prospect of tensile-dominant brittle failure diminishes as the confinement increases away from the excavation boundary. Therefore, it is expected that the transition from tensile to shear mode in the failure mechanism occurs as the confinement level changes and conditions for tensile failure are prevented or strongly diminished. In addition, many uncertainties remain because of the highly anisotropic characteristics of coal seams associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous effort is required to better understand the catastrophic failure mechanisms in coal mines."

Jan 1, 2018

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on cab air filtration system performance. Factors experimentally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab protection performance. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Jarret Thomson

An understanding of groundwater flow is essential for many aspects of mining. This is especially true for the process of shaft sinking through the sandstones of the Manitou Falls Group in the Athabasca Basin of northern Saskatchewan. Experience has shown that the hydraulic conductivities of these sandstones can be relatively high, especially in zones containing natural fractures. To develop a better understanding of the inflow potential into a shaft, a laboratory testing program was undertaken to investigate the hydraulic conductivity of fracture core samples from the Manitou Falls Group. This program involved the measurement of hydraulic conductivities under steady-state flow conditions, while cycling the effective confining pressure across a span that is representative of in-situ conditions. The change in fracture aperture was simultaneously recorded at each confining stress level. It was found that existing relationships relating aperture and flow did not accurately capture the behavior of the samples tested. The effects of fracture staining and infilling were also investigated, and were found to have a notable impact on the hydraulic conductivity.

Jun 1, 2012

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By Lu T. K

A new type of rockbolting system, the self drilling rockbolt, has been studied to develop a 'single pass' bolt for use in rockbolt installation in underground engineering. This single pass bolt forms the basis of a Rapid Face Bolting system which will reduce the amount of time spent in securing a roof during the operation of a continuous miner in the development of a panel.The installation efficiency and anchorage tests were performed in the laboratory on the self drilling bolt and the traditional resin anchorage. bolt. The results of both bolts are cmmnared.

Jan 1, 1993

By Z Zhao

Coal dust is hazardous to underground coal workers and water spray is the most common and economic method for controlling coal dust. Previous studies proved that the addition of surfactants can improve the performance of water spray on coal dust suppression. The evaluation methods for surfactants vary from different studies. The zeta potential test is a common method for evaluating surfactants with ionicity. Generally, the suspension of coal dust with pure water usually showed a negative value of zeta potential. The addition of cationic surfactants can increase the zeta potential to a positive value with a small dosage, while the addition of anionic surfactants can only lower the zeta potential. However, there is a lack of comprehensive study to investigate the relationship between the zeta potential and the suppression performance for coal dust. The aim of this study is to reveal the consistency and discrepancy between the zeta potential and the suppression efficiency of a surfactant. Firstly, the mixture of cationic surfactant solutions and coal dust would be evaluated by the zeta potential test. The wind tunnel tests would then be conducted for the same surfactant solutions to measure and calculate the suppression efficiency. It was found that the addition of surfactant can increase the zeta potential and the suppression efficiency and it reached the greatest efficiency when the zeta potential approached to zero. The equilibrium of zeta potential can benefit the suppression performance of surfactants in the wind tunnel test. The result of this study can achieve a better understanding of the mechanism for coal dust suppression. The selection of surfactants will also be suggested for researchers or industries in terms of coal dust control. It would be more economic if a similar performance could be achieved by less consumption of surfactants.

Oct 12, 2022

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By L. Jacobsson, J. E. Lindqvist

A series of laboratory tests were conducted to study stress-induced spalling on medium to coarse-grained granite specimens. The specimens made from cylinders had two manufactured notches on opposite sides aimed to represent the tangential loading around a circular opening. Specimens of three different sizes were tested with notch radii, 98.5, 225 and 375 mm, representing 197, 450 and 750 mm diameter holes, to study the effect of notch radius on the spalling initiation stress. The cracking was monitored by acoustic emission sampling. The fracture patterns were investigated visually on polished slabs and by microscopy on thin sections. The crack analysis describes how the cracks propagate in relation to the grain structure in the rock and to the macroscopic stress field.

Jan 1, 2015

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

CONTENTSThe significance of values givenINTRODUCTIONTHE ORE1. DATA SECURED FROM THE MILLING PLANT AS OPERATING BETWEEN 1938 AND 1942(a) Mill Recoveries(b) Mill Flow Sheet(c) Scheelite-Garnet Association(d) Detailed Examination of Mill Performance during 1942Crushing UnitsCoarse Rolls DischargeFine Rolls DischargeFeed to Huntington MillsFinal Ground ProductProduction of -200-mesh Scheelite SlimeSummary of Information on Crushing and Grinding Circuit(e) Detailed Examination of Mill Performance During 1942Concentrating UnitsLocation and Nature of Scheelite LossesSize Distribution of Scheelite LossesDistributor Spigot ProductsSummary of Information on Concentration Circuit(f) Detailed Examination of Mill Performance During 1942 Gravity Plant Feed2. EXAMINATION OF MINE SAMPLES TAKEN DURING 1942(a) Introduction(b) Nature of the Ore(c) Sampling of Mill Feed(d) Testing Technique(e) Minus 1/8-inch Ores-Naturally Broken Fractions(f) Recoveries from Plus 1/8-inch Fractions-Crushed to Minus 1/8-lnch(g) Probable Recoveries Obtainable from Weathered Ores140 Contour120 Contour90 Contour(h) Examination of an Ore Sample from the 90-foot Adit(i) Run-of-Mine Ore(j) Evidence of Maximum Sizes of Scheelfte Present in Run-of- Mine Ore(k) Summary of Information on Liberation and Recovery from the Ores as Mined in 1942 and from the Mill Samples

Jan 1, 1944