Search Documents

By M. Q. Xu

During the flowsheet development for a potential commercial Cu/Ni separation plant at the In-co?s Sudbury operation, extensive laboratory and miniplant studies were carried out. There are two potential feed streams for Cu/Ni separation at the existing operation. It is shown that Cu/Ni separation from the rougher concentrate is relatively simple without need of regrind. However, Cu/Ni separation can be difficult from the bulk concentrate because of the presence of excess flotation reagents in the bulk concentrate slurry and locked particles. Excess flotation reagents created excess froth increasing entrainment. By replacing the slurry water with tap water and with addition of some hydrogen peroxide, entrainment is minimized and good Cu/Ni separation is achieved on the bulk concentrate. Fine regrind is required to increase liberation of the locked particles for ultimately high copper recovery at the minimal nickel content.

Jan 1, 2014

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By G. E. Karantzavelos

Anew flotation process to recover alunite from low-grade alunite ores is described. The process begins with run-of-mine ore, reduced to less than 5 mm (0.2 in.), being preconditioned with the reagents before grinding and alunite flotation. From the preconditioning step, ore particles, impregnated with reagents, form pellets that subsequently disintegrate into the pulp during grinding. The second step is basically a standard alunite flotation step. Pilot plant test results show that an alunite concentrate assaying at least 85% alunite and less than 5% silica can be produced. Laboratory and pilot plant results were in excellent agreement, indicating that the new process is a viable means of alunite beneficiation. Plant results, using the new process, were superior to results from conventional alunite flotation procedure.

Jan 1, 1986

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration. Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet.Processing the are as received resulted in 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J.IntroductionA five-year mineral development sub-agreement was signed between the federal government and the province of Manitoba in 1984. The purpose of the agreement was to establish a work program which would strengthen and diversify the mineral resource industry of Manitoba. Basically, the agreement covers three sectors: Sector A, geoscience; Sector B, mining and minerals technology research; and Sector C, development studies.Project selection involved input from industry, federal and provincial representatives. In the case of industrial mineral s, the selection was initiated at a meeting held at the offices of the Department of Mines and Energy, Winnipeg, Manitoba, in October 1985. One such project was the evaluation of the chromite ore deposits at Bird River, Manitoba."

Jan 1, 1988

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration . Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet ,Processing the are as received resulted I n 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J."

Jan 1, 1988

By S. M. Bulatovic, D. M. Wyslouzil, K. R. Rawlings

"The suitability of a new organic reagent DS20 as a depressant for oxidized and carbonaceous pyritic lead-zinc ore from Nanisivik Mines Ltd. has been evaluated in the laboratory and in the plant.The depressant DS20 is a mixture of Lignosulphonate-Dextrin-Quebracho and was developed specifically for depression of highly oxidized and carbonaceous pyrite.The laboratory test work indicated that the poor metallurgy resulting from the oxidized ore could be improved to normal plant performance by the addition of the DS20 depressant with the existing plant reagents. The laboratory data suggested that lime consumption could be reduced when using DS20.In this paper, the development work and the plant trials with DS20 are described.INTRODUCTIONNanisivik Mines Ltd. treats approximately 2000 tonnes per day of lead-zinc massive sulphide ore, containing currently 1% Pb and 9% Zn. The concentrator operations have been described previously (1,2) and typical metallurgical performance is detailed in Table I.The concentrator flowsheet (Figure No. 1) and the standard reagent scheme (Table No. 2) demonstrate the relative simplicity of treatment of this coarse grained ore.A recently discovered satellite orebody - Area 14 - containing 2% Pb and 12% Zn was brought into production in October 1983. This ore had been oxidized to varying degrees by ground water; the pyrite mineralization was found to be very fast floating and a carbonaceous constituent present in higher than normal proportion also affected flotation. The simple high lime addition could not control the pyrite, and very low grade lead concentrates resulted; zinc metallurgy was also affected by this oxidized condition (Table 3)."

Jan 1, 1986

By F. Q. Su

Underground Coal Gasification (UCG) is a promising environmentally acceptable clean-coal technology. A typical UCG system has two wells drilled from the surface into a coal seam with some separation of injection from production. The wells are connected underground by various linking techniques. After creating a combustion reactor in an underground coal seam, air and oxygen flow through the injection well. Heat energy and gases are collected from the production well. As gasification progresses, the combustion reactor is moved along the linking hole. Using this process, the fracturing activity inside the coal seam serves an important role for enlargement of the gasification zone because the surface area oxidization increases continuously by coal cracking. For effective coal gasification, fracturing activity must be controlled. Moreover, excess fractures inside the coal seam and surrounding rock can induce gas leakage, underground water contamination, subsidence, etc. Therefore, monitoring and control of fracturing activity in underground areas constitute key technologies for efficient and safe UCG. To monitor fracturing activity, we conducted laboratory and small-scale field experiments of UCG using acoustic emission (AE) measurements. UCG model tests were conducted for linking and coaxial types UCG models. Coaxial UCG systems are compact and are anticipated for application in underground coal seams having a complex geological structure. The UCG model consists of a coal block molded in a steel canister (20 liter capacity) with heat-resistant mortar, with a linking hole or a coaxial-hole passing through the coal block. During coal combustion, coal temperatures, production gas contents, and AE activity were monitored under the control of injection-air and oxygen flow rates. Results show that the combustion propagated inside the specimen along the linking hole. Many AE events were generated during coal combustion. The AE activity was related closely to temperature changes inside the coal block. This AE generation apparently results from crack initiation and extension around the coal combustion area under the influence of thermal stress. However, comparing the results from UCG models of linking and coaxial types, the gasification of the linking type model showed an average calorific value as high as 11.3 MJ/m3. The coaxial type yielded an average calorific value of produced gas as only 5.79 MJ/m3. In the coaxial type of UCG model, the combustion region was limited to the area around the coaxial hole. The AE activity was lower than in the linking type model. For small-scale UCG field experiments, linking and coaxial types were tested at an open pit coal mine in Hokkaido, Japan. Using a linking type UCG, 58.2 kg coal was processed in 39 h, with the calorific value estimated as 11 MJ/m3. However, the coaxial type UCG processed 7.0 kg coal in 9 h, yielding an estimated calorific value of 6.0 MJ/m3. These tendencies resemble those of results of laboratory UCG experiments. Results of these experiments demonstrate that AE monitoring is a useful tool to evaluate combustion reactors for efficient and safe UCG systems. To develop a coaxial UCG system, results show that fracture control around combustion reactors is indispensable.

Aug 1, 2013

By M. P. Brameld, G. Archambault, R. H. McCorkell

"The rates. J. at which materials emit radon are of interest in studies of the sources of radon in mines. buildings. soils overburden and other places where it may indicate the location of ore or be a health hazard. Here J values were determined by measuring the radon concentrations by means of scintillation counters or alpha-particle track detectors in chambers in which specimens were sealed. Errors in the measurements due to leakage from the chambers. lack of secular equilibrium in the decay series of the radon measured, or the limited rate of diffusion of radon from powders or within the chambers were shown to be insignificant or could be corrected. Scintillation counter measurements are highly reproducible; track detector measurements also appear useable and may be made on many small samples using small, simple chambers. J measurements were made for uranium ores, drill cores, standard CANMET pulps. concrete and gypsum board. Powdering of ores had little effect on their J values.IntroductionIn the mining and mineral sciences, radon (222Rn) is of interest chiefly for two reasons: in geochemical exploration for mineral deposits its presence in soil. overburden and water in more than background concentrations may indicate the existence and locations of uranium deposits and, if present in sufficient concentrations, it is a possible health hazard in mines, mills and other places where people live and work. The latter aspect of radon's role has received considerable attention recently(1,2,3,4,5), and surveys of soil-gas radon concentrations have been used for some time in searches for uranium deposits(6,7,8,9,)."

Jan 1, 1981

By V. B. Achanti

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the: fragmentation process were found to be: bit spacing, bit geometry, depth of cut, and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Three bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 90°. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Respirable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Jan 1, 1997

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997

By V. B. Achanti, A. W. Khair

Introduction Laboratory studies were carried out at West Virginia University to investigate the rock-fragmentation mechanism of continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be bit spacing, bit geometry, depth of cut and cutting-drum rotational speed. This paper presents a discussion of the effects of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation. The removal of rock ridges/walls between adjacent grooves is analyzed with three hits mounted simultaneously on the cutting head, while the bit tip angle was varied from 600 to 900. Bit spacing was varied from 25.4 to 50.8 mm (1 to 2 in.) while the cutting process was assessed for varying cutting depths. Respirable dusts generated during the course of the experiments were analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism of continuous miners in terms of energy consumption and dust generation. A review of the literature revealed that a considerable amount of research has been carried out on rockcutting processes. Many authors agree that the mechanical cutting efficiencies of mining machines (e.g., continuous miners, shearers and road headers) are affected by a host of parameters. Some of these parameters are machine controlled, some are operator controlled, while others are uncontrollable. Efforts were focused on understanding the influence of parameters such as bit spacing, cutting depth, attack angle, bit type, drum speed, bit geometry (i.e., tip size, shape and tip angle) and rock type on the cutting process efficiency in terms of specific energy consumption and respirable dust generation (Strehig?? et al., 1975, Hanson et al., 1979, Khair et al., 1989). Roepke et al. (1976) in an attempt to study the dust and energy generated during coal cutting using point attack bits found that the dust and the specific energy consumed both decrease as the depth of cut increases. The four fundamental stages of dust generation luring rock fragmentation are identified by Zipf and Bieniawski (1989). Coal breakage by various types of wedges was assessed by Evans and Pomeroy (1966) in an extensive experimental study on British coals. Yet the industry today requires further attention and guidance to optimize the energy consumption and dust generation during the rockbreakage process. This paper attempts to give a better understanding of the influence of some of the parameters listed above and focuses on further improvement in the rock-cutting process. The specific energy consumed for different types of bits used and the respirable dust generated are analyzed in the context of the variation of a few other parameters. Laboratory investigation The experiments were performed in the Rock Mechanics Laboratories located at West Virginia University. A rock-cutting simulator designed and fabricated by Khair (1984) was utilized for this purpose. The details of this machine are available in the literature (see Khair 1984). For this study, a series of preliminary experiments was carried out to determine the optimum cutting frame advance speed. This was intended to facilitate a maximum cut depth of 31.75 mm (1.25 in.) at an advance rate of 0.525 mm/s (0.0207 ips) for all types of bits being used and various bit spacings being considered. To look into the cutting-process efficiency of a continuous miner in the laboratory, several parameters of influence are being considered. Besides the bit-geometry parameters, machine- and operator-controlled parameters, such as spacing of bits on the cutting head, the cutting head rotational speed and the total cutting depth during an experiment, are varied. At the time this paper was written, only part of the completed experiments were ana¬lyzed, and a number of experiments were still being carried out following an orthogonal fractional factorial experimental plan to assess the effect of all of the above¬mentioned parameters on the cutting efficiency in terms of energy consumption and dust generation. Three different types of tip angles, namely, 60°, 75° and 90°, and two different tip sizes, namely, diameters of 7.94 and 24.61 mm (0.313 and 0.969 in.), were used. At

Jan 1, 1999

By Fathi Habashi

Laboratory autoclaves for hydrometallurgical investigations are available in a variety of sizes, models, and materials of constructions. They vary in sizes from 25 mL to 2 liters for laboratory studies and 5 to 50 gallons for pilot plant work. They are essential tools for studying aqueous oxidation of sulfide concentrates, dissolution of oxide minerals at high temperature and pressure and hydrothermal precipitation reactions. The maximum pressure and temperature at which any pressure vessel can be used will depend upon the design of the vessel and the materials used in its construction. Since all materials lose strength at elevated temperatures, any pressure rating must be stated in terms of the temperature at which it applies. A review of existing models and their accessories will be given.

Jan 1, 2000

By K. J. Shoop, S. J. Ripke, T. C. Rao, T. C. Eisele

This study investigated the use of a 7.6-cm inside diameter, 344.2-cm-tall horizontally baffled column to reduce the ash content of a low-sulfur bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage and feed quality. The tests were also carried out to compare the columns performance to a conventional column installation in an operating plant. In this paper, the results of this investigation are reviewed and discussed.

Jan 1, 1999

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By S. K. Kawatra, T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of back mixing of tailings into the froth zone, and the recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically constructed very tall (30 to 40 ft) to limit the effects of back mixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug flow. In this work, horizontal baffles were shown to improve the performance of a 6 -ft laboratory-scale flotation column treating a poorly floatable coal. Tests with variations in the baffle positions showed that baffles are needed both above and below the feed inlet to achieve the greatest benefit. Tracer tests with a fluorescent dye in water showed that baffles reduce the amount of feed water entrained in the froth at any given coal recovery.

Jan 1, 1996

By T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of backmixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically made very tall, on the order of 30-40 feet, in order to limit the effects of backmixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug-flow. In this work, horizontal baffles were shown to improve the performance of a 6-foot tall laboratory-scale flotation column treating a difficult-to-clean, heavily oxidized coal. Tests with variation in the position of the baffles showed that for the greatest benefit, baffles are needed both above and below the feed inlet. Tracer tests with a fluorescent dye water tracer showed that the addition of the baffles reduced the amount of feed water entrained into the froth at any given coal recovery.

Jan 1, 1994

By A. C. T. Bigg

Heavy media separation is one of a number of ore-concentration techniques for coarse? feed which, when the ore is amenable, offers economic advantages in the mining stage and/or the processing stage. In mining, simpler and cheaper methods may be used if a greater proportion of waste material can be included in the mining blocks that can later be re-moved efficiently at a coarse size. In the mill, pre-concentration can mean considerable savings in capital and operating costs by down-scaling of equipment sizes particularly in the grinding section. Conversely, throughput may be increased using the equipment already in-stalled in the concentrator.

Jan 1, 1988

By R. G. O’Meara, M. M. Fine

ONE of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.[t] In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.1 The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 ACKNOWLEDGMENT This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. O. E. Anderson, mill superintendent,

Jan 1, 1946

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991