Search Documents

By S. R. Rannels, D. E. Rannels

"I. IntroductionThe alveolar surface of the lung is covered by two populations of pneumocytes, type I and type II epithelium. The type I cell, which accounts for most of the alveolar surface area and provides a highly specialized barrier for gas exchange (Rannels et al., 1991), is poorly understood. Although approaches to type I cell purification have been discussed, they have not been applied widely because of the lack of phenotypic markers to monitor isolation procedures (Dobbs et al., 1988; Danto et al., 1992). In contrast, the type II cell has been studied extensively, largely because of the development of reliable procedures for its isolation and primary culture. Investigations based on the use of purified populations of cultured type II cells have provided convincing evidence to support a role for the pneumocytes both in the maintenance of normal lung function and in the response of the lung to injury (for review, see Rannels and Rannels, 1989).While type II cells can be isolated by a variety of approaches, the protocols used most commonly are modifications of the gradient method of Dobbs and Mason (1979) or of the panning method of Dobbs et al. (1986). Purification of the cells based on density gradient centrifugation is reliable and consistent, with yields of 30 to 40 X 106 type II cells per rat of 230 g body weight. Isolation procedures applied to a minimum of three to four rats provide the best results, as lower cell yields are common with the use of fewer animals. The protocol below is designed to obtain a maximal cell yield from the lungs of six rats.II. Materials and InstrumentationMaterialsCalbiochem: DNase I (Cat. No. 260912); Corning: culture flask, 75 cm2 #25115; Costar: culture plate, 24-well #3424; disposable serological pipette #4101; Elastin Products Inc: elastase #E-134; Falcon: cellulose nitrate membrane filter, 0.22 µm, #7105; conical tube, 50 ml, #2070; culture dish, 100 mm, #3003; culture plate, sixwell, #3046; Fisher: BaS04 , #B68-500; NaCl, #5271-3; NaHC03 , #5233-50; Fort Dodge Laboratories: pentobarbital, #1206-lE; Gibco: Dulbecco's minimal essential medium (DMEM), #430-1600EC; Hanks' balanced salt solution (HBSS), #310- 4185AG; Joklik's modified Eagle's medium (JMEM), #410-2300EC; HyClone Laboratories Inc: fetal calf serum (FCS ), # A-1115-L; I CN Biochemicals (Flow Labora tories): amphotericin B, #16-723-48; newborn calf serum (NCS), #29-121-54; try pan blue, # 19 5 5 32; Na/gene: Erlenmeyer flask, # 100-4116C; Pharmacia: Percoll, #17-0891-01; density marker beads, #17-0549-01; Sigma: gentam1cm sulfate, #G3632; penicillin/streptomycin, #P3539; trypsin inhibitor, #T9128; Tetko: HC- 160 nylon mesh, #3-160-53."

Dec 1, 1995

By H R. Watli, K L. Davies, J A. Johnson

Novel microbial isolates that readily oxidise iron and sulfur were recovered from samples collected from a spent chalcopyrite/pyrite test heap. Methods were developed to enrich and isolate microbes that thrive in low pH environments and utilise iron and/or sulfur as sources of energy. Screening of these isolates revealed diverse substrate utilization (sulfur, ferrous ion, chalcopyrite, pyrite, glucose) as well as growth at temperatures between 30 - 50¦C. When native isolates were employed, shake flask leaching tests of chalcopyrite concentrate resulted in higher copper yields in comparison to laboratory reference strains Acidithiobacillus ferrooxidans (DSM 583) and Sulfobacillus thermosulfidooxidans (DSM 9293). After 700 hours several native isolates had leached between 20 - 30 per cent more copper than laboratory reference strains during experiments conducted at 45¦C. This research has established a unique culture collection of mining microbes that readily adapt to Australian conditions. Exploitation of these microbes may result in improved leaching kinetics and copper recovery from Australian chalcopyrite ores as demonstrated from shake flask leaching tests. Whilst this research provides a capability for Australian mineral sulfide ores, this technology can be easily adapted to suit ores of any origin resulting in more effective and efficient microbial leaching.

Jan 1, 2004

By A. D. Agate

In developing nations, novel mineral processing methods like bacterial leaching are gaining prominence. The principles and practices for isolation and preservation of cultures used in bacterial leaching are discussed with special reference to cultures used in leaching copper from Indian ores. In all, 145 potentially useful microorganisms such as iron- and sulfur-oxidizing bacteria were isolated from various ecosystems of the copper mining areas in the country. The major organisms isolated by enrichment culture technique belonged to T. ferrooxidans and T. thiooxidans species. In addition, thermophilic cultures like Sulfolobus sp. and thermophilic thiobacilli were also isolated. The process of copper leaching was scaled up to the 300-kg level in PVC columns. Since the preservation of efficient cultures in active state was vitally important, a new method was devised that preserved the activity of thiobacilli for a period of more than two years. The novel method of storage in sterile chalcopyrite ore at 8°C can be considered an important advance.

Jan 1, 1987

By Partha Patra

Extracellular bacterial protein (EBP) from Paenibacillus polymyxa was isolated. Adsorption of bacterial cells of Paenibacillus polymyxa as well as EBP onto pyrite, galena and sphalerite was studied. Both bacterial cells and EBP was found to have different adsorption density for different minerals. Protein from mineral surfaces were extrated and examined through SDS PAGE electrophoresis. Specific group of protein was found to be adsorbing, specific to respective minerals. EBP was fractionated through FPLC. Adsorption studies were carried out with each fractions. Difference in adsorption density was observed for individual minerals. Flocculation and flotation experiment were carried out with these mineral specific EBP. Pyrite was selectively removed from ternary mixture of galena and spharite through flocculation anf flotation using pyrite specific EBP. Mineral specific EBP was found to selectively separated remove pyrite from the complex sulphide mixture.Zetapotential studies were carried out to examine the surface chemical changes of the minerals on interaction with EBP. Hydrophobicity of the minerals were carried out on interaction with bacterial cells as well as mineral specific EBP.

Jan 1, 2006

By Abhilash

Different methods of utilizing refractory bauxite and disposing red mud are practiced throughout the world, but none of them are known to be environmentally innocuous due to the complexity and /or high cost, and none has been found to be feasible on an industrial scale. Under these conditions, the use of bioleaching process seems promising. The present study emphasizes on the isolation of native extremophiles from the source Indian bauxite and red mud, with their detailed cellular and physio-chemical, and biochemical characterization. These organisms were tested for their ability to thrive in physically or geochemically extreme conditions. The gram positive capsule rich mesophiles and thermophiles were tested for removal of gangue minerals from the bauxite and red mud samples. Keywords: refractory bauxite, red mud, extremophiles, bio-beneficiation, gangue

Sep 1, 2012

By Mahmood Alemrajabi, Ake Rasmuson, Kerstin Forsberg, Kivanc Korkmaz

"In the present study, the recovery of rare earth elements (REE) in the nitrophosphate process of fertilizer production is investigated. The apatite has been recovered from iron ore tailings by flotation. After digestion of apatite in concentrated nitric acid, Ca(NO3)2.4H2O is first separated by cooling crystallization and then the REEs are recovered by precipitation. Optimum conditions in these steps have been determined in a previous study. The precipitate mainly consists of CaHPO4.2H2O and REE phosphates.In the present study, selective dissolution and re-precipitation have been studied in order to obtain a precipitate that is more concentrated in REEs. The precipitate was selectively dissolved in nitric and phosphoric acid at different acidities (pH 6 to 0) with the liquid /solid ratio of 100 mL/g. It is shown that most of the CaHPO4.2H2O and other calcium containing compounds will be dissolved at pH 2 while the REE phosphates are not dissolved above a pH of approximately 2. Thus, by partial dissolution of the REE precipitate at pH 2.5 most of the solid calcium phosphates will be dissolved and the remaining solid phase, which is more concentrated in REEs, can be filtered off as a fairly concentrated REE solid mass and the liquor can be recycled back to recover more P nutrients. Alternatively, the REE enriched precipitate was dissolved completely in nitric acid and re-precipitated again by addition of ammonium hydroxide to pH 1.2. A chemical equilibrium software, MEDUSA (Puigdomenech, 2013) has been used to evaluate the experimental results and to estimate the optimum conditions for selectively dissolving the precipitate."

Jan 1, 2016

MR JOHN S Foxall wrote: Mr Clayton in his paper on the above subject (Proceedings, N.S. No. 34) made an assertion which should not be allowed to remain unchallenged. On the top of page 10 appears the following statement;- "By viewing the box at adepression angle of 45°, all the dimensions are disclosed and the box may be projected on isometric co-ordinates" and lower down on the same page:- "An isometric plan, being virtually a projection on a plane inclined at 45°, the nearer the dip approaches this figure so is the outline of the stoping more truly shown." Those statements embody an inaccuracy which would be misleading were an isometric plan to be constructed to suit a special case, ie the case of a mine whose lode dipped at 45°, or approximately 45° and it would be found that in such a plan the outline of the stoping would not be truly shown. The reason for this is that the depression angle at which an object is viewed in order to...

Jan 1, 1920

IN the construction of a set of ordinary mine plans, two axes or coordinates are used; also, two different projections are essential viz., a plan (horizontal projection) and longitudinal section (vertical projection). In isometric projection three axes are employed-one axis vertical and the remaining two inclined to it at angles of 120°, also making an angle of 120° with one another, as shown in Fig. 1. The two inclined axes are used to plot the horizontal projection, while altitudes are plotted on the vertical axis. As an illustration, consider the ease of a simple object, such as a box. To show all the dimensions in the usual manner requires two drawings-a plan and elevation, as in Fig 2.

Jan 1, 1919

Isometric strength is defined as the capacity to produce force or torque with a voluntary isometric (muscle[s] maintain[s] a constant length) contraction. The key thing to understand about this type of contraction and strength measurement is that no body movement occurs during the measurement period. The tested person's body angles and posture remain the same throughout the test. Isometric strength has historically been the type most studied and measured. It is probably the easiest to measure and to understand. Some strength researchers feel that isometric strength data may be difficult to apply to some "real life" situations because in most real circumstances people are moving - they are not static. Other researchers counter that it is equally difficult to determine the speed of movement of a person or group of persons doing a job (each moves in his or her unique manner and speed across the links and joints of the body). Thus, dynamic strength test data collected on persons moving at a different speed and/or in a different posture from the "real world" condition will be just as hard to apply. In truth, neither is better - they are different measurements. Both researchers and users should collect and use data that they understand and that fits their application. Workplace Assessment When a worker is called on to perform a physically demanding lifting task, the external load produces moments - tendencies to produce motion, also called torques - about various joints of the body.(1) Often these moments are augmented by the force of gravity acting on the mass of various body segments. For example, in a biceps curl exercise, the moment produced by the forearm flexors must counteract the moment of the weight held in the hands as well as the moment caused by gravity acting on the forearm's center of mass. To perform the task successfully, the muscles responsible for moving the joint must develop a greater moment than the combined moments of the external load and body segment. It should be clear that, at each joint of the body, there is a limit to the strength that the muscle can produce to move ever-increasing external loads. This concept forms the basis of isometric muscle strength prediction modeling.(1) The following procedures are generally used with this biomechanical analysis technique. First, workers are observed (and usually photographed or video-taped) as they perform physically demanding tasks. For each task the posture of the torso and the extremities are documented at the time of peak exertion. The postures are then re-created using a computerized software package, which calculates the load moments produced at various joints of the body as the task is performed. The values obtained during this analysis are then compared to population norms for isometric strength obtained from a population of industrial workers. In this manner, the model estimates the proportion of the population

Jan 1, 1998

By D. Warkentin, T. Yeomans, R. Tavakoli, A. Nacu

"One of the most successful commercial methods of extracting gold from ores involves solubilizing gold as a gold cyanide complex, followed by adsorption of the complex onto activated carbon. The gold cyanide is subsequently eluted from the carbon to produce a concentrated gold solution suitable for electrowinning to recover the precious metals. Stripped carbon is treated in a kiln under a flowing steam atmosphere to reactivate its surface, allowing it to be reused. The aim of this study was to investigate the gold elution using a mixture of sodium hydroxide and isopropyl alcohol in both batch and continuous tests, with the eluates being electrowon on carbon foam cathodes. The effects of various factors, including alcohol content and sodium cyanide addition were studied. The addition of alcohol considerably improved gold elution kinetics, while the presence of sodium cyanide did not have a significant impact on either elution efficiency or kinetics. In all cases, efficient electrolysis was shown to be an important factor in maintaining effective carbon circuit operation.INTRODUCTION Gold dissolved as Au(CN)2- complex during cyanidation is recovered either by cementation with zinc powder, also known as the Merrill-Crowe process, or by adsorption into activated carbon through Carbon-in-Pulp (CIP) or Carbon-in-Leach (CIL) processes. Activated carbon loaded with gold is then eluted and gold is subsequently recovered by electrochemical methods. Conventional elution processes such as atmospheric and pressurized Zadra processes, involve stripping with a cyanide (0.1–0.2% NaCN) and sodium hydroxide solution (1–2% NaOH) at high temperature (90–140°C) over long elution times of 8 to 72 hours. In the Anglo American Research Laboratories (ARL) elution process, the acid-washed loaded carbon is pretreated with a strong sodium cyanide and sodium hydroxide solution (1–5% NaCN and 1–2% NaOH), followed by elution with water at 110–130°C. Solvent-assisted elution processes have also been reported, such methods use varying concentrations of alcohols (methanol, ethanol and isopropanol), ketones, or glycols to enhance atmospheric elutions at temperatures up to 95°C (Muir et al., 1985; Ubaldini et al., 2006; Espiell et al., 2008; Soleimani & Kaghazchi, 2008). The present work investigates the efficiency of isopropanol in the gold elution process, as well as the methodology of evaluating gold stripping processes in the lab setting"

Jan 1, 2017

By M. Albertson

AT Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin' Was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 in.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 in.), the width at the lower lobe was about. 1000 ft., and the, width at the narrows probably. 400 to 500 ft. The original depth of water varied from 20, to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft.. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the. lake. About

Jan 2, 1921

By Yunnen Chen

In the present study, waste materials like pine sawdust and spent grains were investigated to assess their potential for removal of cobalt ion from water by the process of biosorption. The effects of solution pH, reaction time and initial concentration were studied in batch experiments. The removal efficiency of Co(? ) by spent grains was higher than that of pine sawdust. The initial removal was rapid and equilibrium was established in less than 90 min. Equilibrium data all agreed well with both Langmuir and Freundlich isotherm models for the two metal-biomass sorption processes. Good correlation coefficients were obtained for the pseudo second-order kinetic model. Pine sawdust and spent grains were shown to be promising biosorbents for Co(? ) removal from aqueous solutions.

Jan 1, 2010

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Zhenbo Zhao

The processes and equipment for INLRFH (Isothermal Normalizing by Utilizing the Residual Forged Heat) of alloy carburizing steel products are presented. It is shown that four key parameters: namely (I) cooling rate before isothermal normalizing, (IT) the lowest cooling temperature before isothermal normalizing, (111) isothermal normalizing temperature and (IV) isothermal normalizing time, should be controlled. The prediction and calculation of these parameters can be achieved on the basis of components treated and the technical requirements of the steel parts by an on-line expert system. The cost-reductions due to the energy savings resulting from implementing this system for automotive parts heat-treatment are most promising.

Jan 1, 1999

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

This study aims to investigate the reduction thermodynamics of ilmenite and pre-oxidized ilmenite, and reveals the isothermal reduction kinetics of pre-oxidized ilmenite concentrate by carbon monoxide. The results indicate that the ilmenite concentrate and pre-oxidized ilmenite concentrate can be selectively reduced by controlling the temperature. The pre-oxidation process leads to the breakage of complex mineral structure, and the formation of porous simple oxides, which is an effective method to increase the reduction and leaching rate. 

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Jie Qiu, Yun Chen, Kai Tang

Isothermal reduction kinetics of CF2 by 30% CO and 70% N2 at 1123, 1173 and 1223 K was investigated by TGA in this study. The reduction rate analysis indicated that reduction of CF2 comprises three stages during the whole reduction process, Apparent activation energy of samples CF2 reduction is 34.37 kJ/mol. The ln-ln analysis implied the reduction of CF2 was expressed initially by a 2D subsequently by 3D shrinking layer reaction.

Mar 1, 2017

By Hongling Wang, DI WU, Shuai Li, Hui Shu

Isothermal reduction experiments on carbon-bearing pellets of copper slag were investigated by the thermogravimetric method with biomass carbon as a reducing agent. The results indicated that the reduction process of copper slag‑biomass composite pellets was dominated by gas phase diffusion, and the apparent activation energy was 88.44 kJ/mol. In the temperature range from 1000 to 1200 °C, the metallization rate of pellets increased with increasing temperature, and the maximum metallization rate was 78.4%. The optimal reduction temperature of CSBCP (copper slag-biomass composite pellets) was 1200 °C.

Nov 23, 2022

By J Taguta, B. McFadzean, P. E. Ngoepe, M. G. Mulaudzi

Computational modelling methods and isothermal titration calorimetry (ITC) were employed to investigate the interaction of a pyrite surface with thiol collectors. Modelling work was conducted in the presence and absence of water. Microcalorimetry was employed to investigate the resultant energy of interaction pyrite as a result of mineral-collector interactions. Sodium ethyl xanthate (SEX), diethyldithiocarbamate (DTC) and diethyl dithiophosphate (DTP) were investigated in this study. The results showed that the calculated surface energies and morphologies for FeS2 showed that (100) and (111) are the most stable surfaces. The morphology also indicated the appearance of the (100) and (111) surface facets and no presence of others. The calculated adsorption energies between thiol collectors and the pyrite surface were always more exothermic than the experimentally determined ones. When comparing different ligand types with the same alkyl chain length, the heat of adsorption of diethyl-DTC was greater than that of ethyl xanthate and diethyl-DTP for pyrite. Experimentally, the diethyl DTP barely adsorbed onto the pyrite surface and this may be due to a different mechanism of action. In computational calculations, water adsorption was found to reduce the reactivity of the Fe atom for the interaction with thiol collectors, and bring the adsorption energies closer to the magnitude of the experimental values. Keywords: Computational modelling, microcalorimetry, experimental and thiol collectors, adsorption energies

Jan 1, 2020