Search Documents

By Sven Fornander

An account is given of the way in which a new process for desulphurization of hot metal is carried out at a Swedish blastfurnace plant. In the process powdered burnt lime is used as a desulphurizing agent in a rotary furnace. Results are given. IN a paper by Kalling et al.* the fundamentals of a new process for desulphurization of hot metal using powdered burnt lime as a desulphurizing agent were outlined. The purpose of the present paper is to give a brief account of the way in which this process is being carried out in practice by Surahammars Bruks AB, Sweden, and of the results obtained. + The hot metal from the blast furnace is tapped into a ladle of 15 tons capacity and transferred to a rotary furnace, a simplified drawing of which is given in Fig. 1. The rotary furnace has a total length of about 160 in. and an outside diameter of the rings of about 130 in. The furnace is in a horizontal position, with its rings placed on four rollers, and can be rotated by a driving mechanism at various speeds of up to 34 rpm. The rotary furnace and its driving mechanism were designed and constructed at Surahammar. The hot metal is charged into the rotary furnace through the opening to the left in Fig. 1. See Fig. 2. An addition is then made to the furnace consisting of finely ground burnt lime amounting to 2 pct of the weight of the hot metal as well as 0.5 pct of coke breeze. After the additions are made, the furnace is sealed to the atmosphere by means of two lids and set in rotary motion at a rate of 34 rpm. The sulphur in the hot metal is rapidly absorbed by the lime added, the time of treatment needed is normally 30 min. The process is then stopped, the lid is removed, and the furnace is lifted up by a crane and used as a tilting ladle for pouring the metal into the pig-iron molds, Fig. 3. Process Metallurgy The hot metal charged into the rotary furnace has a composition which usually lies within the following limits: C, 3.70 to 4.10 pct; Si, 0.80 to 1.80; Mn, 0.40 to 0.80; P, 0.025 to 0.030; and S, 0.060 to 0.200. Figs. 4 and 5 give examples of the changes in hot metal composition taking place during the treatment in the rotary furnace. As will be seen from the diagrams, the sulphur content of the metal decreases very rapidly during the first 10 min of treatment from about 0.100 to about 0.020 pct S. During the following 20 min, the sulphur content goes down slowly to about 0.005 pct S. The carbon and silicon contents of the metal decrease by about 0.10 pct each during the treatment. The manganese and phosphorus contents remain unchanged. Thus, if the process is started with an iron of the composition given above, the finishing composition of the metal usually lies within the following limits: C, 3.60 to 4.00 pct; Si, 0.70 to 1.70; Mn, 0.40 to 0.80; P, 0.025 to 0.030; and S, 0.002 to 0.020. The chemical reaction taking place during the process can be written:

Jan 1, 1952

By Sven Fornander

L. F. Reinartz (Armco Steel Corp., Middletown, Ohio) —I would like to know, in the practical application of the Kalling process, what kind of a lining was used, how thick was the lining, and how much metal was treated at one time? S. Fornander (author's reply)—The rotary furnace is lined with a course of fireclay bricks 6 in. thick. This course is backed by 5 in. of insulation. The furnace has a capacity of about 15 tons. Mr. Reinartz—How was the ladle preheated? Mr. Fornander—As pointed out in the paper, the furnace was heated by a gas flame in the beginning of the experiments. During these first tests, however, the desulphurization was inconsistent. We think that this was due to the fact that iron droplets sticking to the furnace walls were oxidized by the gas flame. Now, the furnace is operated without preheating of any kind, and the results are much better. T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—I might add one comment. This furnace was heated with a flame and for a time they had a little difficulty due to some residual metal in the rotating drum that would oxidize in between treatments and they found therefore, that it was very essential to drain the drum completely of metal so that they would not build up any ferrous oxide between treatments and they eliminated some of their erratic heats by maintaining those more reducing conditions. It was interesting to watch this operation. As soon as the drum started to rotate there was considerable flame, at least, at the time I saw it, that came out around the flanges, indicating there was quite a little pressure on the inside of the drum. W. 0. Philbrook (Carnegie Institute of Technology, Pittsburgh)—Is the reaction slag in the Kalling process liquid or solid, and how is it separated from the metal? Mr. Fornander—In the process there is no slag in the usual sense of the word. The lime powder does not melt during the treatment. After the treatment the lime is still in the form of a fine powder. It is separated from the metal by means of a piece of wood of suitable size placed within the furnace before it is emptied. D. C. Hilty (Union Carbide & Carbon Research Laboratories, Niagara Falls, N. Y.)—Dr. Chipman has given us some of his ideas in connection with a specific effect of silicon and silica on sulphur elimination and how silicon might interfere with desulphuriz- ing in the blast furnace. I wonder if he would like to elaborate on the possibility of a similar effect of silicon in the Kalling process? J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—Silicon does not interfere with the Kalling process. Anything that has strong reducing action is good for desulphurization. In these tests where the temperature was low compared to blast furnace temperatures, the silicon that is in the metal is a better reducing agent than the carbon. At high temperatures, carbon is the better. It is not the silicon in the metal that interferes with desulphurization, it is the silica in the slag. Mr. Joseph—I might add that the metal that was tapped from the drum after desulphurization was really at quite a low temperature. It was not measured, but I think it was well under 1300 °C, probably 1200" or a little above that. That was one of the difficulties, and I think there is no question about the fact that the Kalling process—in that it affects desulphurization between powdered lime, solid and liquid iron— is a reaction definitely between the solid lime and the liquid iron. E. Spire (Canadian Liquid Air, Montreal, Canada) — This Kalling process seems very interesting to us and after all it is only a mixing action that is taking place between the iron and the slag. We have attempted to do the same thing in another way. We have placed at the bottom of the ladle a porous plug through which we injected an inert gas. It can be nitrogen or argon. This plug is placed at the bottom of the conventional ladle and gas injected through the plug. That has appeared in our patent. To define this new type of treatment, I use the word gasometallurgy. I do not know if you like it, but it is a way of defining methods of treating metal using gases. What we do is exactly what is done in the exchange process in another way. We have a porous plug at the bottom with a high lime slag on top of the metal. Using this method, we have very good agitation of metal and slag, and with a small flow of gas, we can achieve a very strong agitation. For instance, in the 500 lb ladle, we use only 5 liters of gas a minute. We have an agitation compared to very rapidly boiling water in a pail. Moreover, the agitation can be controlled to create any amount of mixing desired. In a few minutes, with this method, the sulphur dropped from 0.58 to 0.11. These results have been improved since, and we have obtained results like 0.08

Jan 1, 1952

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Jan 1, 1963

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Experimental results are given for the rate of reduction of silica from silicate melts by paphite-saturated iron in the presence of carbon monoxide. It is shown that, when gas bubbles are present at the slag-metal interface, the interfacial chemical reaction is the rate-controlling process in the transfer of silicon from slag to metal. From the silicon-concentration profiles in the metal sample, the diffusivity of silicon in paphite-saturated iron is found to be (5.4 * 0.4) x 10 sq cm per sec at 1600°C. Some consideration is given to the transport of oxygen from the slug-metal interface to the walls of the gvaphite metal container as becoming the rate-controlling process in the absence of gas bubbles at the slag-metal interface. ATTEMPTS were made by Fulton and chipman1 to investigate the kinetics of reduction of silica from calcium alumino-silicate melts by graphite-saturated iron in an atmosphere of carbon monoxide. In these experiments with 400 to 500 g of metal and slag, both phases were stirred in such a manner that the interface was essentially undisturbed. Initially, the graphite-saturated iron contained about 15 pct Si and, after about 8 or 10 hr of reaction time at 1600°C, the silicon content of the metal in- creased by about 0.2 pct. In a written discussion on this paper of Fulton and Chipman, schuhmann2 pointed out the possibility that this observed slowness of the reduction of silica could be due to the transport of oxygen across the liquid metal boundary layer at the slag-metal interface. Although this explanation of Schuhmann is quite feasible for the experimental data of Fulton and Chipman on silica reduction, such a reasoning should not be extended to other rate data on slag-metal reactions unless sufficient evidence is available satisfying the boundary conditions for such a transport process. The hydrodynamics of stirred liquids are very complex and even for a simple method of stirring there is no exact mathematical solution which will predict the mass transfer coefficient accurately. The best available solution of this problem is that given by Lewis' and later modified by mayers~ for a two-liquid system where liquids are stirred by counter-rotating stirrer blades without disturbing the interface. In such a system the mass transfer coefficient is estimated from an empirical relationship using the data on viscosity and density of the two liquids, rate of revolution, the length of stirrer blades, and the diffusivity of the element which is transferred from one phase to the other. It was found in these investigations' that the estimated and observed mass transfer coefficients, in systems containing two immiscible aqueous solutions, agreed within *40 pct. Although this is not considered to be an unreasonable error for the study of industrial processes, uncertainties of this magnitude cannot be tolerated in any theoretical study of reaction kinetics. In view of the complexity of the

Jan 1, 1963

By J. Chipman, J. C. Fulton

Reduction of Si from slag to carbon-saturated iron is a very slow reaction. The rate is nearly independent of stirring but is accelerated markedly by increased temperature. In a slag containing 45 pct SiO2, 38 pct CaO, 17 pct Al2O3, the energy of activation is approximately 130 kcal. AT temperatures of 1450" to 1600°C occurring in the hearth of the iron blast furnace, chemical reactions are normally expected to proceed with great rapidity. Many of the reactions of iron making are indeed quite rapid and attain a condition corresponding roughly to a state of equilibrium before metal and slag are tapped from the furnace. The one conspicuous exception is the reaction by which carbon in the coke or metal reacts with silica in the slag to deliver silicon to the metal. From the practical viewpoint the slowness of this reaction is indeed fortunate, for if it were fast enough to reach equilibrium during the time of contact, it would be difficult to produce pig iron of the desired low silicon content. The one other reaction which under certain circumstances can also be very slow is the transfer of sulfur from blast-furnace metal to slag. In their laboratory exeriments on this reaction, Hatch and Chipman found that at least 5 hr were required for the attainment of equilibrium in a small crucible and that the reaction was not accelerated by increasing the rate of stirring. Subsequently it was shown2 that the presence of a reducible oxide MnO greatly inhibited sulfur removal, and finally that SiO2 itself3 under some conditions has sufficient oxidizing Dower to interfere with sulfur transfer. The kinetics of sulfur removal are now rather well understood,4 and it has been shown3,5 that when the silicon content of the metal is high enough to prevent reduction of SiO,, the desulfurizing process is rapid. Thus the observations of slow removal of sulfur are associated with the coincident slow reduction of SiO2, a process which transfers both silicon and oxygen to the metal phase. It is, of course, the oxygen which interferes with sulfur removal. An explanation of the slowness of the silica reduction reaction has not been obtained. The sulfur transfer process has been shown by the authors5 to be at least partially transport-controlled in the absence of interference by silica. Under the experimental conditions. 99 pct of the total transfer at 1600" was accomplished within an hour. Under similar conditions the reduction of silica may not proceed half-way to equilibrium6 in 8 hr. It is scarcely imaginable that silica reduction could be transport-controlled when the slag contains 44 pct SiO2 and the metal about 1.4 pct C. The experiments reported here show definitely that it is controlled by a slow step or steps in the chemical reaction. One might expect to find such a slow step in the breaking of SiO bonds or in the slow removal of oxygen by carbon at the slag-metal or metal-crucible interface or by bubble formation. EXPERIMENTAL PROCEDURE The experimental procedure used in this investigation was similar to that used in the study of the kinetics of desulfurization.5 A sketch of the graphite crucible and stirrer used in the current work is shown in Fig. 1. The quantity of metal and slag used was adjusted so that the slag-metal interface was located between the top and bottom blades on the stirrer; the top of the slag layer was above the top blade. The stirrer shaft was hollow down to the metal level and served as thermocouple well or optical pyrometer target. Stirring speeds of 0 to 500 rpm were used. A carbon monoxide atmosphere was maintained in the furnace by flushing the gas over the slag surface, except in run No. 220 when it was bubbled

Jan 1, 1960

By A. E. Jenkins, L. A. Baker, N. A. Warner

The electromagnetic levitation technique has been successfully applied to rate studies of the de-carburization of liquid Fe-C alloys from 5.5 to zero pct C at 1660°C using gas mixtures containing 1 to 100 pct CO2 with CO or helium as diluents. The rate was shown to be independent of carbon concen -tration in the melt and only slightly affected by total pressure. The results were shown to be consistent with control either wholly or predominantly by gaseous diffusion. As well as avoiding side reactions with the crucible, levitation allowed precise calculation of reaction rates since the geometry of the system was accurately known. It also enabled interpretation using the established mass-transfer correlations for a gas flowing past a single sphere, The existence of gaseous-diffusion control and the extremely high rates of reaction reported for gas flowing past small spheres are of great practical significance in relation to current investigations into the use of spray-refining techniques in continzcous steelmaking. PREVIOUS work on the kinetics of carbon removal from liquid iron has generally involved the use of oxygen as the gaseous oxidant. Investigations have been made on commercial steelmaking furnaces and in addition laboratory-scale experiments have been attempted with a slag phase present. The general lack of agreement and the obvious difficulty in interpreting the results is at least partly due to the complexity of the systems used. This work has been reviewed by carter1 and more recently by Bods-worth2 and ward.3 The gas-liquid metal reactions have also been studied with slag-free melts by the conventional technique of blowing oxygen onto the melt contained in a crucible. The reaction between the oxidant and carbon could be followed by sampling either the melt or the gas phase. Side reactions with the crucible material have precluded direct interpretation of the results. Fujii, 5-7 using O-A mixtures, attempted to correct for the crucible reaction and reported that the reaction between carban and oxygen occurred at the melt surface and was controlled by gaseous diffusion for carbon contents greater than a critical value and by carbon-diffusion control in the metal for carbon contents less than the critical. The critical value was given as approximately 0.15 pct C. However, whereas this was the case for oxygen contents in the gas stream up to 10 pct, between 10 and 20 pct the rate was found to be approximately independent of oxygen content, and Fujii attempted to explain this observation by postulating the presence of an oxide "film".7 Turkdogan et a1.' have studied iron fuming during decarburizing and suggested gaseous-diffusion control of the reaction above a critical carbon concentration, given as approximately 2 pct C. Filippov9-12 reports in a similar manner to Fujii but makes no mention of the crucible reaction with the carbon in the melt, even though this would be expected with the temperature, crucible material (MgO), and carbon contents used. Both CO2 and O2 were used as oxidant gases. In the present work the decarburization of liquid Fe-C alloys was studied using an adaptation of the electromagnetic levitation technique, and thus the complexities introduced by crucible side reactions were eliminated. In this technique a single sphere of the Fe-C alloy is freely suspended and heated by electromagnetic induction in a flowing stream containing the oxidant gas. The full range of carbon levels up to saturation was studied, the temperature of the melts in this instance being held constant at 1660°C. The oxidant was CO2 which was used either pure or in association with a diluent gas, the total gas pressure being maintained either at 1 atm or at a reduced pressure. Thus the reaction under study was:

Jan 1, 1964

By Kiyoshi Azuma, Hiroshi Kametani

Dissolution of a ferric oxide in acid solution is divided into two different types In the accelerated type dissolution proceeds in three stages 1) an inittal reaction during which the dissolved amount of oxide is nearly proportional to the cube root of time ; 2) an accelerated reaction: and 3) a final stage during which dissolution approaches completion. This course of dissolution gives an S-shaped curve in the above sequence OH a log weight percent of dissolved oxide against log time graph. In the parabolic type dissolution proceeds in four stages: first and second stages similar to those of the accelerated type; 3) parabolic-rate dissolution during which the dissolved amount of oxide is nearly proportional to the square root of time: and 4) a final stage. The effect of the kind of acid, the temperature of solution, and the concentration of acid was investigated. The results are discussed and a rate equation is proposed. AN attempt has been made to obtain some information on dissolution of a ferric oxide in various acid solutions. In view of hydrometallurgical processes the dissolution of ferric oxide is of less importance than that of zinc oxide or copper oxide in general. One of a few processes which intend to dissolve ferric oxide is an elimination of iron impurity from acid-insoluble materials. However, most leaching processes of oxide ores and cinders are accompanied with more or less dissolution of iron. According to Pryor and Evans1 the rate of dissolution of a ferric oxide in various acids decreased in the order of hydrofluoric acid > hydrochloric acid > sulfuric acid > perchloric acid. This order was in accord with the order of decrease of the complexing affinity of the anion for ferric ion,

Jan 1, 1964

By M. E. Wadsworth, J. R. Lewis, J. M. Quets

Samples of snythetic magnetite were reduced in hydrogen at various partial pressures and temperatures. The reaction mas found to be surface controlled and directly proportional to hydrogen partial pressure over the temperature range studied (400° to 1000°C). A transition in the mechanism occurred at approxirnately 590°C. This has been attributed to a change in the slow step of the reduction reaction resulting from the presence of stable wüstite at higher temperatures. Below 590°C the heat of activation for the reduction was found to be 14,700 cal per mole and it was 3,200 cal per mole above 590°C. THE reduction of the oxides of iron has been a subject of study and interest for many years. Edstrom1 has reviewed the work up to 1953 and his findings provide much basic information concerning details of the reduction of hematite (Fe2O3 ) and magnetite (Fe3O4) with both H2 and CO. He concluded that below 600°C the reduction of both hematite and magnetite was essentially identical, since the rate was controlled by a surface reaction at a magnetite gas interface and the iron formed was very porous. The decrease in the reduction rate for both hematite and magnetite immediately above 600°C was attributed to the formation of a stable wüstite phase across which diffusion was very slow. The wide difference in reduction kinetics for hematite and magnetite above 600°C was explained in terms of the character of the wüstite formed. The rate of magnetite reduction increased slowly with temperature beyond the minimum immediately above 600°C and rates equivalent to those observed at 550°C were not obtained until the temperature was increased beyond 850oC. Edstrom and Bitsianes2 studied the solid-state reduction of magnetite, the reaction of which can be written (4x-3)Fe + Fe3O4—4 FexO [1] where x is between 0.83 and 0.95. The rate was found to be controlled by the kinetics of transport of iron ions through the wüstite phase. Bogdandy and Riecke3 studied the kinetics of reduction of small grains of iron oxide in hydrogen and qualitatively attributed the slow step in the reduction process to the diffusion of hydrogen and water vapor through pores. McKewan4 has analysed the data of Joseph,5 Stalhane and Malmburg,6 and Lewis7 and has demonstrated that the kinetics of reduction of both hematite and magnetite are controlled by surface reactions and also that the variation in surface area during reduction must be accounted for. McKewan was able to correlate the reduction data by the equation rodo[1-(1-R)1/3] = Kt [2] where ro is the initial particle radius, do is the density of the iron oxide, R is the fraction reduced at time t, and K is a rate constant. The applicability of Eq. [2] for temperatures above 600°C where a stable wüstite phase is present, indicates the slow step in the over-all kinetics does not result from diffusion unless diffusion occurs laterally along the oxide metal interface or through a wüstite layer of constant thickness. Diffusional control through a layer of wüstite is unlikely, however, in view of the pressure effects demonstrated by Tenenbaum and Joseph,' Diepschlag,9 McKewan,10 and the results of the present study. McKewan has demonstrated a linear rate dependence on the hydrogen partial pressure over the temperature range 400" to 1050°C for the reduction of hematite.

Jan 1, 1961

By W. M. McKewan

Jan 1, 1961

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate of oxidation of ferrous iron to ferric iron in pure molten iron oxide by carbon dioxide + carbon moloxide mixtures at 1550°C. It is shown that the rate-controlling process is the interdiffusion of iron and oxygen atoms within the melt. The inter-diffusivity of iron and oxygen in the melt is obtained from the results and the value of (5.0 * 1.0) x 10-5sq cm per sec is recommended for the temperature of 1550°C. Similarly, it is also found that the rate of reduction of molten iron oxide is con -trolled by diffusion in the melt; however, apparent interdiffusivity values from these experiments are 10 to 20 pct higher than those obtained in the oxidation experiments, by virtue of convection arising from density difference. The results of the oxidation experintents are used to calculate an estimated self-diffusivity of iron in molten iron oxide of (1.5 * 0.5) x sq cm per sec. BECAUSE of the industrial importance of iron oxides, the study of the kinetics of both the reduction and oxidation of the solid oxides has received a great deal of attention. However, knowledge of the kinetics of similar reactions in the liquid state is very meager. Dancy 1 studied the kinetics of reduction of molten iron oxide by carbon in pig iron and found that the reaction is very fast. It was concluded from the results that the reduction of molten ferrous oxide is a first-order reaction up to 80 pct reduction, while

Jan 1, 1964

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate 0.f solution of nitrogen in y iron in the temperature range 1000° to 1200°C. It is shown that, when purified reacting gas is used, the rate-controlling process is the diffusion of nitrogen into the iron. The difhsiuity of nitrogen in y iron is calculated from the results and the equation logD = —(8800/T) — 0.04 is recommended to represent the temperature dependence of the diffusivity. In some experiments using unpurified nitrogen, solution rates are found to be slower than those attributable to a solely solid-state diffusion process. Indications are that in the presence of impurities in the gas, e.g., H,O, chemisorption of nitrogen at the surface is hindered and becomes a rate-controlling process for the transfer of nitrogen across the gas -metal interface. ALTHOUGH the solubility of nitrogen in y iron at known nitrogen activities has been well-established,'-a the kinetics of the solution of nitrogen in iron are not known. The work of Darken, Smith, and Filer' indicates that at temperatures below about 1300°C the rate of solution of nitrogen in y iron is controlled by a chemical reaction at the metal surface, while at temperatures above about 1300°C the rate-controlling process is the diffusion of nitrogen in the metal. Fast and verrijps studied the denitro-genization of y iron using wet hydrogen at 950°C and their results clearly indicate that the rate of nitrogen removal is controlled by diffusion of nitrogen in the metal. In Part I of this series of papers, the kinetics of the solution of nitrogen in y iron are discussed in the light of the present experimental work. EXPERIMENTAL Apparatus. The reaction chamber consisted of a platinum wire-wound resistance furnace with a re-crystallized alumina reaction tube. The temoerature of the furnace, which was automatically controlled to approximately 1°C, was measured with a Pt/Pt-13 pct Rh thermocouple and a potentiometer. The temperature distribution in the working zone of the furnace was determined using a calibrated Pt/Pt-13 pct Rh thermocouple and the hot zone was found to be approximately 3 in. long with a temperature variation of * 3°C. A series of experiments was also carried out at 1000°C and pressures above atmospheric using a pressure vessel which was similar in construction to that described elsewhere.1° Materials. Ferrovac E grade iron used in all ex-

Jan 1, 1964

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg' using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962

By R. D. Pehlke, P. D. Goodell, R. W. Dunlap

The rate of dissolution of steel bars in molten pig iron has been measured experimentally in the temperature range 2300° to 2650° F. The rate of solution is shown to be a .function of bath composition, temperature, and stirring. A kinetic model based on carbon diffusion in the liquid phase has been derived to fit the experimental results. THE rate of scrap melting has long been an important variable in steelmaking operations. With the advent of the oxygen steelmaking process and the accompanying shorter heat times, the rate of scrap melting has now become one of the rate-limiting factors in steel production. As observed in commercial practice, the solution rate is influenced by the compositions of liquid and solid, the temperature, agitation, and time. However, no definitive work has been done on the Fe-C system, and there is very little information in the literature regarding the relative effects of these variables in steelmaking systems. A number of questions have been raised in regard to scrap utilization in basic oxygen steelmaking operations. Consideration has been given to the optimum size and shape of scrap, and to the use of preheated scrap as a means for decreasing the pig-iron requirement in oxygen blowing. The determination of an optimum scrap practice for a specific installation depends to a large extent upon the economics of the scrap market and also upon the behavior of scrap in the vessel. The present research was undertaken as a preliminary study in evaluating the behavior of steel in a pig-iron bath under various conditions of temperature, composition, and agitation, as might be encountered in oxygen converter operations or in any steelmaking operation where scrap behavior is an important process variable. Related studies have been carried out on non-ferrous systems. The solution rate of solid aluminum in a molten A1-Si alloy has been studied.' Furthermore, the increasing use of liquid metals has created considerable interest in studies related to dissolution of a solid in a liquid, or mass transfer taking place between a solid interface and a liquid metallic phase.2-10 In an effort to clarify the relative importance of factors influencing the dissolution of scrap in Fe-C alloys, this paper presents the results of a study of the rate of dissolution of a low-carbon steel cylinder in a molten Fe-C bath at various bath compositions, temperatures, and conditions of agitation. An attempt has been made to determine the mechanism of solution, and a model has been derived to fit the experimental results. The rate of heat transfer between the molten pig-iron bath and the solid-steel cylinder has also been studied. EXPERIMENTAL PROCEDURE A molten bath of pig iron (nominal composition 4.2 pct C, 0.5 pct Mn, 0.8 pct Si)* was held in a 200- *In view of the fact that the composition of the pig-iron bath was slowly changing with time because of steel dissolution and reaction with the surrounding atmosphere, intermittent samples of the liquid bath were taken throughout each experiment, Table 1. lb induction melting unit. The internal diameter of the furnace was 8-1/2 in. and the bath depth approximately 14 in. Cold-finished 1020 steel cylinders of 1/2-, 3/4-, 1-, 1-1/2-, and 2-in. diameters were cut into 1 -ft lengths for use as test specimens. One end of each bar was machined to fit a hand-driven, mechanical stirring device which rested on top of the furnace. This fixture permitted 7 to 8 in. of the bar to be immersed in the melt. The steel cylinders were cleaned to free the surface of grease and oxide. The rods, at ambient temperature, were immersed into the molten pig-iron bath. The melt temperatures studied in this investigation were 2300°, 2500°, and 2650°F. Different agitation conditions were achieved by operating with a) the power to the furnace, giving induction stirring; b) induction stirring plus mechanical stirring, using hand rotation with a chain and sprocket assembly at approximately 200 rpm; c) mechanical stirring alone with the power off; and d) the power off and no mechanical stirring resulting in minimum agitation, i.e., only that caused by natural convection currents in the bath. The samples were immersed in the melt for prescribed times ranging from 30 sec up to 6 min. Immersion times were measured with a stopwatch and temperature control of the melt was achieved by power adjustment following temperature measurement with an optical pyrometer. The measurements with the calibrated pyrometer were checked out to within less than 10°F with simultaneous thermocouple measurements. Following immersion, the bars were water-quenched and the diameters were measured with a micrometer at several positions on the reduced area, and by volumetric displacement. The dissolution rates calculated from the

Jan 1, 1965

By E. T. Turkdogan, M. L. Pearce

The rates of sulfurization and desulfurization of calcium aluminate, silicate, and ferrite melts by CO + CO2 + SO2 mixtures at 1550°C are reported. It is shown that for melts 10 to 15 mm deep transport of sulfide ions within the melt controls the rate of sulfur transfer. The rate data from shallow melts, i.e., 1 to 4 mm deep, have been analyzed on the basis of a diffusion or a reaction controlled process and indications are that the both processes may play a part in controlling the rate of sulfur reaction. The rates of desulfurization of silicate XVEACTION equilibria between metals, metal oxides, and gases have received considerable attention in recent years. However, the understanding of and aluminate melts increase with increasing PCO2/PCO ratio in the gas stream, the effect being most marked for aluminate melts. The sulfide equilibrium data obtained from the present work are shown to be in accord with the results of previous studies. It is shown that carbon dioxide has a measurable solubility in silicate, aluminate, and ferrite melts. Consideration is given to the partial equilibria which control the directions and the rates of reactions occurring simultaneously in complex heterogeneous systems. the kinetics of heterogeneous reactions, particularly those occurring at elevated temperatures has not been improved appreciably. Almost all the metallurgical reactions occur in heterogeneous systems involving two or more phases. Although in many authoritative text books and original Papers the basic principles concerning the kinetics of heterogeneous reactions are clearly underlined, they are seldom used to the best advantage in kinetic studies, particularly those involving the metallurgical reac-

Jan 1, 1963

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962

By G. R. St. Pierre, A. J. Wilhelem

In connection with the reduction of hematite or magnetite to metallic iron, it appeared desirable to study the rate of reduction of each oxide to the next lower oxide under conditions which excluded all other condensed phases. For this purpose, pellets of Fe,O,, Fe,O,, and oFeOo were prepared. A gas train for the preparation of Ar-Hz-H20 mixtures was employed to establish a continuous flow of a controlled atmosphere over a pellet suspended on a balance. In this manner the following individual reduction steps could be studied: For example, pellets of hematite were reduced solely to magnetite by adjusting the gas atmosphere such that it was oxidizing to wustite. In other words, the reaction was complete when the hematite pellet had been totally converted to magnetite. The pellets were prepared from Baker Chemical ferric oxide. The ferric oxide powder was moistened and handrolled. Air sintering at 950°C produced Fe,0, pellets with a density of 3.65 g per cm3. The pellets ranged in size from 0.6 to 1.2 cm diam. The magnetite and

Jan 1, 1962

By E. S. Machlin

The kinetics of vacuum distillation, vacuum-melt surface reactions, crucible-melt surface reactions and boiling are analytically investigated. No disagreement with experiment is obtained upon applying a rigid flow model to describe the behavior of the melt in the vicinity of reaction surfaces. The theory focuses attention upon measureable parameters rather than upon the adjustable parameter, stagnant layer thickness, associated with other theories. The rigid flow theory is thus capable of quantitative evaluation and experiments to achieve this evaluation are suggested. KINETICS, rather than thermodynamics, often determine the degree of refinement achieved in vacuum melting. There is little understanding, however, of the kinetic principles involved in vacuum refining. This paper represents an attempt to achieve this understanding. There are two reactions which need to be con- sidered. The first is the refining reaction. The second shall be called the polluting reaction. It is the reaction associated with the introduction of components of the crucible into the melt. The mechanisms of both reactions are unknown. Many models can be constructed to describe either the refining or polluting reactions. For example, consider the refining reaction C + Q = CO(g). One model that can be imagined is that the carbon and oxygen combine in the melt to form CO which then diffuses to a melt-

Jan 1, 1961

By K. C. Mills, E. T. Turkdogan

A number of investigators1 6 have noted the presence of a liquid miscibility gap in the Fe-Sn binary system. However, the first attempt to measure the

Jan 1, 1964

By Walter Crafts, D. C. Hilty

The liquidus diagram for the iron field of the Fe-S-O system has been derived experimentally. The solubility of oxygen in molten Fe-S alloys has been measured at several temperatures and found first to decrease slightly and then increase rapidly with increasing sulphur content. IT is well-known that the types, distribution, and amount of inclusions in any given steel are closely allied with the oxygen and sulphur contents of the metal, so that the term "deoxidation" as conventionally applied in steelmaking refers not only to the control of oxygen and oxide inclusions but to collateral modification of sulphide inclusions as well. Inclusions commonly occur in steel as mixtures of oxides and sulphides, sometimes closely associated and sometimes apparently completely divorced. Their effects on the properties of the metal may vary widely depending on their types and distribution as well as on their quantity. The mechanism by which inclusions form, however, and the means for controlling it are exceedingly complex and not well understood. Nevertheless, as described by Benedicts and Lofquist' and by Wentrup' all oxide and sulphide inclusions, excluding mechanically entrained matter, must result from specific modifications of the basic equilibria of the Fe-S-O system. In an investigation of the mechanism of deoxidation and inclusion formation being carried out at the Union Carbide and Carbon Research Laboratories, it became evident that quantitative data for the fundamental Fe-S-O system were essential to a better understanding of the problem. Consequently, the liquidus surface of the portion of the Fe-S-O diagram of interest in steelmaking has been determined, and the solubility of oxygen in liquid iron containing sulphur has been measured. Fe-S-O Diagram The portion of the Fe-S-O diagram of specific interest in steelmaking is the Fe-FeS-FeO corner. Of the contiguous binary diagrams for this partial system, only those for Fe-FeO and Fe-FeS are known with reasonable certainty.3 Several attempts to derive the FeO-FeS diagram have been made, chief among them being the work of Giani as reported by Oberhoffer,4 and, more recently, that of Vogel and Fulling." Although both Giani and Vogel and Fulling published diagrams for the FeO-FeS system, their observations indicated that the oxide component approximated Fe3O4 rather than FeO, so that there is doubt whether the system is truly binary. Benedicts and Lofquist and also Wentrup published qualitative sketches of the ternary diagram based on the assumption that it was of the type described by Marsh for a ternary system in which two of the contiguous binary systems are simple eutectic systems and the third exhibits a solubility gap in the liquid. Apparently, however, the only previous effort to establish the diagram experimentally was that of Vogel and Fülling whose results are reproduced in Fig. 1. Although defining approximately the limits of the miscibility gap and the location of the ternary eutectic, point E in Fig. I, Vogel and Fülling's diagram must be considered only semiquantitative. It was derived from a limited number of observations mainly along two quasi-binary sections, and the directions of the tie-lines and the location of the critical point, K in Fig. 1, were estimated by computation. Experimental Procedure The experimental technique employed for the present investigation involved melting mixtures of ferrous sulphide and ferric oxide in contact with iron. Since it was considered that in this part of the system the vapor pressures of sulphur and SO, are so low that they would not affect the results significantly, the melting was carried out in a current of argon to sweep out products of any initial re-

Jan 1, 1953

By H. F. Beeghly

UNTIL recently the only criteria by which steels were judged were their cost and their mechanical, chemical, and physical properties. The user was concerned with such properties as corrosion resistance, tensile strength, response to thermal treatment, hardness, ductility, and, to a growing extent in recent years, with behavior at high temperature. As plans were made to build power reactors, a new set of properties became important—the nuclear characteristics, which had to be considered by the designer and engineer in building his plant. The nuclear engineer developed methods for the rare and new metals and produced them in high purity, often at great expense. The pure metals then provided the raw materials for tailor-made alloys. For more common structural metals, such as steel, the nuclear industry depended on commercially available materials. Generally, the quantities required were small and specifications were rigid. It is not surprising, therefore, that difficulty was frequently encountered in procuring structural mate-

Jan 1, 1957