Search Documents

By Sid T. Killan

The utilization of the reducing power of blast-furnace gas can be estimated by applying two rectifying calculations to the gas analysis. A resulting corrected CO/CO2 ratio varies inversely with furnace production. Directions for calculating the corrected CO/CO2 ratio are given, and a corrected CO/CO2 ratio is compared with actual furnace production. THE inadequacy of the normally accepted CO/CO, ratio as a measure of blast-furnace performance and furnace efficiency was discussed following the presentation of the paper by H. F. Dobscha.' In this outstanding example of careful observation on large scale blast-furnace operation, the changes occurring with beneficiated ores were: 1—A net gain in tonnage of 21.2 pct. 2—A decrease in net coke of 15.3 pct. 3—A decrease of 1.9 pct in the CO/CO, ratio. In this great change in furnace performance, the CO/CO, ratio proved itself worthless. The discussion of the inadequacy of expressing furnace performance and efficiency by the CO/CO, ratio led indirectly to the calculations forming the basis of this paper. At that time Dr. T. L. Joseph said: "We must consider difference in CO, from the stone in the two cases when we talk about the ratios of CO/C02." This statement is used for the second of the two CO/CO, ratio corrections forming the basis of this paper. The research work in attempting to find out why the furnaces could op-erate so differently with practically the same CO/CO, ratio lead not to the answer sought but, after a shift to the gaseous phase in the research work, the proof that the normal CO/ CO, ratio was outmoded and a new corrected ratio should replace it. To be of any value, any new corrected ratio should express approximate furnace efficiency and give an idea of practical furnace performance to be expected. This the normal CO/CO, ratio has failed to do. However, in the absence of anything better, some credence has been attached to the normal CO/CO, ratio. As far as the writer can ascertain, the present paper is the first attempt to change or improve the normally accepted index of

Jan 1, 1952

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By W. H. Gauvin, N. J. Themelis

Jan 1, 1963

By W. O. Philbrook, H. W. Hosking, N. B. Melcher

A simple and inexpensive mercury-tracer method has been develohed to study rates and Patterns of gas flow in blast furnaces. A Pulse of mercury is injected into the hot blast, and its arrival at the sampling Point is recorded by an electronic circuit that measures resonant absorbtion of ultraviolet light by mercury vapor in the gas aspirated .through the detecting. cell. A rapidly developing interest in blast-furnace technology in recent years has created a strong demand for precise knowledge of the rates and patterns of gas movement through the stock column. Classical fluid-flow theory cannot supply the desired information because the complexity of the blast-furnace situation precludes the accurate determination of many of the parameters required for solution of the equations. In fact some of the terms employed in fluid-flow treatments become almost meaningless under blast-furnace conditions. The void fraction of the stock column, for example, varies widely from place to place and is affected by the segregation of charge materials, attrition of lumps during descent, and channeling. Gas density varies with changes in local pressure, temperature, and composition, while viscosity varies with temperature and composition. Even if mean values for these functions were acceptable, they would be either impossible or extremely difficult to determine with a high degree of accuracy since the value of the mean for all gas properties would depend upon the flow distribution itself. Attempts to study gas movement by the pitot-tube determination of kinetic pressures have met with little acceptance. Reproducibility of results is extremely difficult to achieve in a situation where alignment of the tube orifice with respect to the flow direction in tortuous channels cannot be guaranteed. Because of these difficulties it would appear that progress can be achieved only with a direct method of measuring gas velocities and determining the shape of flow paths through the stock. The establishment of such a method is described in this paper. SELECTION OF METHOD Direct measurement suggests the use of a tracer by means of which the progress of a "parcel" of gas can be followed through the furnace. Several requirements must be met before any selected material can be considered a suitable tracer. First of all, it must be a substance not normally present in blastfurnace gas or dust; otherwise its presence in a gas sample will have little significance. It should be volatile at temperatures normally existing within the furnace, to ensure that it will travel with the gas, as a gas. It should possess special properties enabling its presence in the gas to be detected readily, and it should not undergo exchange reactions with any material normally present within the furnace, including refractories and coke as well as all components of the metal and slag. Radioactive materials naturally are considered because their radioactivity renders them susceptible to detection. However, of the many radioactive materials available, almost all are eliminated from final consideration by their unsuitability in terms of other properties. Radioactive silicon, carbon, calcium, phosphorus, and many others have been considered and discarded, either because they are not volatile over the whole range of significant temperatures, or because they could be expected to undergo exchange reactions with burden or refractory materials. Others which might be suitable in terms of these properties are eliminated because of a low activity, short half life, or the necessity for fragile counting apparatus. Of the many elements available in radioactive form, perhaps radon is the only one suitable for blast-furnace gas-flow studies. This has been used in several investigations1-4 with considerable success. The use of radiotracers has certain inherent disadvantages. One is the cost. An appreciable sum must be allowed for materials each time a test is made. Also, special methods of handling must be employed, and very often the progress of an investigation must be governed by the availability of isotopes and the delivery arrangements that can be made for them. An advantage is immediately gained if the tracer material can be a substance which can

Jan 1, 1960

By G. C. Gardner

A new correlation of blast penetration in model and operating blast furnaces is presented which overcomes objections to prevzous correlations. It is shown that the tuyere diameter is only of small importance in determining the magnitude of the penetration. The data from operating furnaces correlate satisfactorily with the data from models whose cross section is a segment of a circle. A bubble-shaped gas space called a "raceway" normally exists in front of the nose of a blastfurnace tuyere. The periphery or "wall" of the raceway is well defined and is composed of densely packed charge particles. The blast. issuing as a jet from the tuyere, entrains gas from the raceway, in the usual manner of a jet, as it flows to the opposing wall. There it divides and flows back around the walls to be entrained once more. The blast must, of course, eventually leave the raceway and pass up through the charge column, but before it does it may, on the average, make several circuits of the kind described and in doing so it carries with it charge particles, which, because of their fast and circulating motion, suggested the name of "raceway". A fuller description of the raceway may be found elsewhere."' Here it is only necessary to mention, in addition, the measurement which characterizes its size. If an iron bar is pushed through the opened peepsight of a tuyere, .as far as it will go with ease, it will be stopped by the relatively impenetrable opposing raceway wall arid the distance that the bar has been pushed from the tuyere nose is called the "penetration". This measurement may be of practical importance and has; been the subject, with considerable success, of several attempts at correlation with other variables2-5 as stated in the next section. There is still, however, a serious objection to the most recent correlation,3 which is overcome by the correlation proposed in this paper. It will be shown that the objection is not trivial, in that the new correlation will attribute considerably different importance to the variables affecting the magnitude of the penetration. The data to be treated were made available by Wagstaff and are the same as those used in his correlation. They include measurements taken on small models, in which a cold air blast was used and no combustion occurred, and they also include data from operating blast furnaces at Wheeling and Fairless. The information from the blast furnaces will be shown to be in substantial agreement with those models whose plan views are segments of a circle and which are thus like segments of a blast furnace. First, Wagstaff's most recent correlation3 will be discussed and the objection will be given. Then the new correlation will be developed and its implications considered. CORRELATION OF J. B. WAGSTAFF Wagstaff's correlation is where and D — the penetration D,-the internal tuyere diameter V —the blast velocity in the tuyere

Jan 1, 1961

By R. T. Pepper

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80° to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- ° diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By Ming-Kao Yen

S. E. MADDIGAN*—I think Mr. Yen should be complimented on doing a very excellent and a very comprehensive piece of work. I was particularly pleased to note the use of X rays in a somewhat less tedious technique than pole figures. In the past I think many workers have been diverted away from the use of X rays in such investigations because of the large amount of work involved in pole figures if one is dealing with a great number of specimens. The same thing, I think, applies to the determination of orientations by counting of twins which is also a very tedious procedure; as a result several papers which have otherwise been of excellent quality have depended upon etching techniques for determination of orientation. The present paper indicates that the results reported in those previous papers were correct, but I think the use of etching techniques alone is a rather shaky basis for setting up theories in the literature. W. M. BALDWIN, JR.*—This discussion will be a short note of correction and apology. In my discussion of Brick, Martin and Angier&apos;s paper I incorrectly reported the orientation of phosphorus deoxidized copper annealed at temperatures. When I learned that Mr. Yen was preparing the present paper I asked that he correct this previous error, which he most graciously consented to do. However, through my ambiguity the correction noted on p. 59 of Mr. Yen&apos;s paper is still not the proper one. For this I take full responsibility. The orientation which I observed in phosphorus deoxidized copper at high temperatures is the (112) [111] which agrees with the pole figure given in Fig 8a, on p. 65 of Mr. Yen&apos;s paper. Our observations were made on the basis of twin counts rather than X ray determinations and therefore serve as an independent confirmation of Mr. Yen&apos;s data. M. K. YEN (author&apos;s reply)—The author wishes to thank Dr. Maddigan for his comments in regard to the application of glancing technique to textures. As a matter of fact, considerable work has been done recently in connection with

Jan 1, 1950

By B. M. Larsen, T. E. Brower

A perspective is presented of the steel plant sulphur distribution and elimination problem from coal to liquid steel ready for teeming, giving distributions of sulphur over a range of coke sulphur content, and some methods of sulphur control, in the blast furnace, external desulphuriza-tion between blast furnace and open hearth, distribution between fuel, slag, and metal, and methods and limitations of control of sulphur in the open hearth furnace. AS a part of the 1951 AIME symposium on sulphur in steelmaking, it was thought that a discussion of the distribution of sulphur throughout the whole series of operations, from coal and ore to finished steel ingots, might have some value in giving a perspective on the whole problem. The following discussion is an attempt to present such an overall picture. The order is that of the actual plant operations, beginning with a very brief consideration of the coking process. Sulphur in Coal and Coke Since by far the largest source of sulphur entering the steelmaking cycle is in the coal used to make coke for the blast furnace, it would seem reasonable to eliminate some of it, either from the coal, or the coke, or during the coking process. This has appeared impracticable up to the present, at least, for two main reasons: the low activity of the organic sulphur in either coal or coke, and because of price limitations involved in treating a low cost material such as coke. A variable portion, usually M or less, of the sulphur is present in coal in the form of pyrites or similar compounds, and a large part of this sulphur may be removed in the coal washery. Most of the sulphur, however, is normally present as "organic" sulphur, intimately associated with the coal structure. Its distribution prevents any separation by mechanical means. Its low activity makes improbable &apos; any rapid chemical removal, although hydrogen will remove sulphur from both coal and coke. Thus, prolonged recirculation of coke oven gas in the coking process would tend to leave a smaller percentage of the total sulphur in the coke residue. Table I shows a typical distribution of sulphur from coal into products in the coking process. As the sulphur in the coal increases, the sulphur in the coke tends to increase in about the same proportion. Sulphur in the Blast Furnace The best picture of the situation in the blast furnace is provided by a sulphur balance of raw materials entering, and of products leaving, the furnace. The difficulties in accurate weighing and sampling of the variable solid materials entering this process, and the number of hours required for the raw materials to descend through the furnace under variable operating conditions, make it difficult to obtain an accurate balance. However, balances made over periods of weeks or months tend to average out some of these uncertainties. Table I1 presents three typical sulphur balances similar to a number that the writers have calculated. In most of these the slag volume calculated from the sulphur balance is, in some instances more, and in other instances less, than the value corresponding to the best input and output balances of the other slag constituents (lime, silica, alumina, etc.). Probably the greatest source of error in these calculations is the sulphur content of the slag. Despite some possible inaccuracies the balances of Table II show rather definitely the following points: 1—That 87 to 95 pct of the total sulphur input is in the coke and 95 to 97 pct of the total sulphur output is in the slag. Also, that if any sulphur leaves the furnace with the gas it is relatively small, amounting to a possible 1 pct or less. 2—At the lower sulphur coke level of 0.86 pct the total amount of sulphur charged is 15 Ib of sulphur per ton iron increasing to 26 lb per ton at the higher sulphur, intimately associated with the coal struc-rare burdens containing sulphur-rich ores will the total sulphur burden fail to be nearly proportional to the content in the coke used. 3—The 7 to 9 pct of the total sulphur input from the limestone of furnaces B and C is due to the relatively high sulphur content of the stone, 0.226 and 0.265 pct, respectively. In the case of furnace A, the sulphur content of the limestone was only 0.06 pct which resulted in only 3 pct of the total sulphur input coming from this source. It is rather interesting to compare the sulphur balances of a typical ferromanganese furnace with

Jan 1, 1952

By H. W. Meyer, H. N. Lander, F. D. Delve

A method of calculating the changes in blast-furnace performance brought about by burden and/or blast modifications is presented. Essentially the method consists of three simultaneous equutions derived from materials and heat balances. These equations can be used not only to evaluate quantitatively the effect of changes in process operating variables on furnace performance, but also to provide a useful means of evaluating changes in process variables which cannot be measured directly. It has been customary for a number of years to use simple heat and materials balances as a basis for assessing blast-furnace practice. A good example of the method used to set up these balances is that proposed by Joseph and Neustatter.1 This approach to process assessment has limited utility, however, in that it cannot be used to predict the furnace coke rate or production under new operating conditions. Using an approach based on multiple correlation of blast-furnace variables, R V. Flint2 has developed an equation which may be used to predict the change in coke rate that will result from some changes in operating conditions with a reasonable degree of accuracy. Although this equation has useful applications in production planning, it cannot be used to study the relationships between the operating variables and the fundamental thermochemi-cal characteristics of the process. In attempting to analyze the blast-furnace process quantitatively, the idea of dividing the furnace into zones3 may at first appear attractive. In our present state of knowledge, however, it is not possible to define with any accuracy the physical limits of such zones in relationship to their temperatures or to the reactions which may occur in them. Although its application is restricted, the zonal approach to blast-furnace analysis is useful in some instances. For example, the change in the calculated flame temperature in the "combustion zone" caused by injecting steam constitutes information which is helpful in understanding why the addition of steam to the blast is best accompanied by an increase in blast temperature. The zonal approach cannot, at the present time, be used to establish the relationships between process variables and process performance if the whole process rather than part of it is to be considered. One of the earliest approaches to the problem of relating blast-furnace operating variables to pro- duction and coke rate was that developed by Marshall.4 Essentially Marshall&apos;s work showed that it was possible to estimate the performance of a furnace by solving three simultaneous equations which consisted of rudimentary carbon and heat balances plus a further equation relating the production, wind rate, and the carbon burned at the tuyeres. Although these equations did not include all of the chemical and thermal variables of the process, their derivation and application seems to be the earliest attempt which achieved any success in relating prior furnace operating data to the calculation of furnace performance under different blast conditions. Work carried out in Germany has been directed mainly towards prediction of coke rates using material and thermal balances rather than statistical methods. wesemann5 used prior furnace operating data as part of the basis for predicting the change in coke rate accompanying a change in burden composition. This author employed a method of successive approximations to estimate the secondary changes in slag volume and stone rate brought about by the change in coke rate. The most recent analysis, which seems to have been developed concurrently with the thermochemical model presented in this paper, has been described by Georgen.6 This author has succeeded in improving on Wesemann&apos;s approach by expressing the total changes in the slag volume and stone rate in terms of the change in coke rate itself. This is accomplished in a manner similar to that used in the thermochemical model described in this paper. Although Georgen makes use of a calculated furnace heat loss, he does not relate the heat loss per unit of hot metal to the production rate as is done in the present work. Georgen&apos;s approach may be used to calculate the changes in materials requirements accompanying changes in furnace operation; it cannot be used to assess the resulting changes in production. The fact that blast-furnace behavior can be interpreted by consideration of the heat requirements of the process was demonstrated by Dancy, Sadler, and Lander.7 In the analysis of blast-furnace operation with oxygen and steam injection these authors showed that it was possible to account for the changes in production and coke rate

Jan 1, 1962

By S. Ramachandran, R. A. Walsh, J. C. Fulton

A method has been developed for calculating the oxygen content of commercially melted stainless steels. Application of thermodynamics to the de-oxidation reaction in straight chromium and Cr-Ni stainless steels has resulted in a set of equations DURING the past 30 years, many rewarding developments have resulted from the application of physical chemistry to steelmaking. A need still ex- which permits the calculation of oxygen contents. The model was programmed for computer calc~ilations. The validity of the method was demonstrated on routine oxygen samples from numerous commercially melted heats of stainless steel. ists for further progress in the use of thermodynamics to meet the more stringent requirements for cleaner steel. Current electric furnace practices have been developed around minimizing residual-oxygen content, one of the most important factors controlling the inclusion content of stainless steels. The residual oxygen is controlled by the use of deoxidizers during the finishing period and a number of empirical rules have been evolved. Although this feature of electric furnace practice has long been in use, only in recent years has funda-

Jan 1, 1963

By Terkel Rosenqvist

THE desulphurization of molten iron and steel is a very complicated process. One way to arrive at a better understanding of this process is to break it down into several simpler chemical processes that can be studied individually in the laboratory. For a study of the different factors that influence the equilibrium distribution of sulphur between liquid metals and slags, several simpler equilibria may be investigated. One very important subject is the determination of the escaping tendency of sulphur in the liquid metal and its dependency on temperature and composition of the melt. Several papers in this field have recently been published.&apos;, &apos; Another subject is the study of the sulphur capacity of the slag. A molten slag is indeed complex, and even if sulphur distribution data for a large variety of molten slags may give empirical data about their desulphurizing power, the importance of the individual components is still not quite clear. It is accepted generally that lime is the most important desulphurizing component in the slag. The present investigation has as its purpose to study the desulphurizing power of lime in its standard state, and to provide a basis for thermodynamic calculations of the desulphurizing power of various lime-containing slags. The standard state of lime at steelmaking temperatures is solid calcium oxide, CaO. It can react with sulphur to form solid calcium sulphide, CaS. The relative stability of calcium oxide and calcium sulphide is expressed by the free energy of the reaction: 2Ca0 (s) + S1 (g) = 2CaS (s) + O2 (g) The existing free energy data for this reaction, listed by Kelley5 nd Osborn,&apos; are uncertain to about 10 kcal and are of limited value for a calculation of equilibrium constants. Under the conditions prevailing in a melting furnace, the sulphur pressure may be expressed conveniently by the ratio H,S/H2 and the oxygen pressure by the ratio H,O/H, (or CO,/CO). The desulphurizing power of calcium oxide may, therefore, be studied by the reaction CaO + HIS = CaS + H2O. A study of this reaction may be complicated by certain side reactions: Water vapor and hydrogen sulphide may react. to form sulphur dioxide, and calcium sulphide may be oxidized to calcium sulphate. A thermodynamic calculation shows that these side reactions will be suppressed to insignificance if the equilibrium is studied in the presence of an excess of hydrogen. The apparatus used is shown in Fig. 1. About 10 g calcium oxide and 20 g calcium sulphide (laboratory qualities) were intimately mixed, and some water was added to make a thick paste. The paste was put into a thimble of zirconium silicate, which was placed within the constant temperature zone of a furnace, and capillary refractory tubes were attached in both ends. After the mixture had been heated in dry hydrogen at 1000°C for several hours all Ca(OH), and CaCO, had decomposed and CaSO, was reduced, so only CaO and CaS remained in the thimble forming a porous plug. The mixture was examined by X-ray diffraction after the initial reduction in dry hydrogen as well as after the subsequent experimental runs up to 1425 °C. It was shown that crystalline calcium oxide and calcium sulphide were always present together in about equal amounts. The unit cell edges were found to be 4.80A for CaO and 5.68A for CaS in good agreement with existing literature values." This shows that the mutual solid solubility is very small, and that the compounds are present in their standard states. Purified hydrogen was passed through water sat-urators kept at constant temperature in a thermostat bath. The amount of water vapor saturation was checked by means of a dew point method, not shown on Fig. 1. The gas mixture was passed through the capillary inlet into the furnace, where it was sifted through the porous plug of calcium oxide and calcium sulphide. The hydrogen sulphide present in the outgoing gas was absorbed in a zinc acetate solution and the hydrogen was collected over water. When one liter of hydrogen had been collected, the amount of hydrogen sulphide was determined by iodometric titration. As one molecule of H,O is used for the formation of each molecule of H,S, the equilibrium ratio H,S/H,O would be , where (H,O) is the molar concentration in the ingoing gas, and (H,S) the molar concentration in the outgoing gas. In the present work (H,S) was always very small compared to (H20). In order for the observed H,S/H20 ratio to represent the true equilibrium ratio the gas flow has to be: 1—Sufficiently slow to give a complete establishment of equilibrium, and 2—sufficiently fast to counteract thermal diffusion. Incomplete reaction would give a value decreasing with increasing flow rate, and thermal diffusion would give a value increasing with decreasing flow rate. When inlet and outlet tubes of about 2 sq mm cross-section were used, the observed gas ratio was independent of the flow rate between 15 and 125 cc per min, Fig. 2. In this range, therefore, the observed gas ratio represents true equilibrium.* For the rest of the in-

Jan 1, 1952

By Terkel Rosenqvist

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann&apos;s finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author&apos;s reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp p/RT, where p is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf&apos;s can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson&apos; have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,&apos; have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By G. M. Yocom

Blowing acid Bessemer converters with oxygen-steam produces steel of below 0.002 pct N2 content. This method of blowing, combined with a dephosphorizing treatment in the steel ladle, results in low-carbon steels of low nitrogen and low phosphorous (under 0.035 pet) contents, which has physical properties equivalent to open-hearth steels of similar analysis. Using a 50-50 mixture of oxygen and steam, the refinitzg rate is increased 25 pct over blowing with natural air, and scrap charge increased from 3 to 10 pet. Bottom life is normal with proper tuyere area and arrangements, fumes are decreased, yields increased, and hydrogen content is normal. THE acid Bessemer plant at the South Works of Wheeling Steel Corp., consists of two 15-ton bottom blown converters with a monthly capacity of 57,000 N.T. The product of the shop is skelp billets for continuous welded pipe and slabs for ordinary drawing and forming quality sheets. Approximately 50 pct of ingot production is regular Bessemer steel of natural Phos content and the remainder is a dephosphorized grade of steel made by a special treatment of the blown metal as it is poured into the steel ladle. The low Phos grade of steel has certain advantages over the higher Phos grade but since both grades were produced by blowing natural air, the N2 content was in the range of 0.015 pct which limited its application. In 1954 it was decided to explore the possibilities of blowing with a steam-oxygen mixture for the production of steel of both low N2 and low Phos contents. The necessary equipment was installed to operate one converter in this manner and early in 1955 an experimental run of 160 heats was made by blowing with a steam-oxygen blast and excluding natural air entirely. During this period the proper operating techniques were established, such as blast pressures, steam-oxygen mixtures, valves and instrumental control equipment, tuyere arrangement in the bottoms, blowing times and production rates, and a thorough study made of the final steel quality. Also during this experimental period the dephosphorizing practice was improved by the use of a tap hole below the lip of the vessel. This provided a clean separation of the acid converter slag and blown metal which made the dephosphorizing treatment more effective. The results of this experimental run dictated further development of this practice and a second run of 720 heats was made in 1957. The quality features and conversion cost results were in line with expectations and accordingly a 400-ton per day oxygen plant is now being installed. The plant is scheduled for completion in September of this year. This will provide sufficient oxygen to operate both vessels on steam-oxygen blast and delete natural air blowing entirely. The steel will then be below 0.002 pct N2 bar content and the dephosphorized grades will be between 0.015 and 0.040 pct Phos. STEAM-OXYGEN BLOWING The steam for the process is fed to the plant at 220 psig pressure through a 6-in. line. The high-purity oxygen is compressed to 200 psig and conducted through an 8-in. line. The oxygen from the main line is valved down to 100 psig and passed through a steam heated heat exchanger. The heat exchanger is regulated to supply oxygen at 300°F to the steam-oxygen mixing station. It is essential that the incoming oxygen be held at this temperature to avoid condensation of the steam with resulting excessive erosion of the clay tuyeres in the vessel bottom. Oxygen is admitted to the mixing chamber by a 6-in. hydraulically operated valve driven by the ratio control regulator on impulse from the flow of steam. Steam is admitted to the steam-oxygen mixture station through a 2 1/2-in. hydraulically driven valve. The ratio control regulator acts to increase or decrease oxygen input as the steam flow increases or decreases with changing positions of the Blower&apos;s control lever. The important point to note here is that steam flow always precedes the oxygen flow as a safety measure. The control valves have sufficient capacity to afford protection should blow pipe trouble develop. A 50-50 mixture for these 15-ton heats demands an oxygen flow of 3800 standard cu ft per min along with 317 lb of steam. The Blower&apos;s stations is provided with an indicating blast pressure gage, and indicating steam and oxygen flow meters. Signal and warning lights indicate the valve positions and line pressures. A control room at the real of the Blower&apos;s pulpit room houses the ratio control and pressure regulators, as well as the various meter bodies. The hand actuated wheels used to change the conditions are mounted on a panel on the front of the meter control house. The recording steam and oxygen meters used for totalizing and accounting purposes are also mounted on this panel.

Jan 1, 1962

By T. C. M. Pillay, John Chipman

The Si-0 equilibrium in liquid iron was investigated in some detail by Gokcen and Chipman1 who reported equilibrium constants of the following reactions: In each case the thermodynamic equilibrium constant K was obtained by extrapolating K&apos; to infinite dilution. Their results on reaction [I] were consistent with those of earlier observers, and there seems to be little doubt as to the approximate validity of the equilibrium product determined. On the other hand, the results on reactions [2] and [3] indicated unusual curvilinear relationships between the activity coefficients of silicon and of oxygen and the silicon concentration. Since a linear relation is observed in all other similar instances, it was concluded that some source of error had affected the gas-metal equilibrium relationships. Recently the authors undertook a restudy of these equilibria with the view especially to establishing the equilibrium constant of reaction [2]. Their experiments, however, were discontinued before a tbroughly satisfactory answer had been obtained and consequently have remained unpublished until the present time. Quite recently Matoba, Gunji, and Kuwana2 published the results of a very thorough study of these equilibria. It is the purpose of the present note to Compare these three sets of experimental data, a comparison which leads to Confirmation of the results of Matoba and coworkers. The experimental arrangements described by Dutilloy and Chipman were employed. A controlled mixture of Hz, H,0, and argon was led into the induction furnace over the surface of the Fe-Si melt contained in a silica crucible. On account of the slow approach to equilibrium, runs were continued for at least 8 hr and, in some cases, as much as 12 hr. Samples were taken by means of silica tubes at the start and during the final 4-hr period of each run. Out of twelve runs only seven appeared to have approached equilibrium with sufficient certainty to be reported here. The results of these experiments, all at 1600°c, are shown by the triangles in Fig. 1. Equilibrium was approached from both oxidizing and reducing conditions and the direction of approach is indicated by the shape of the triangle. Attempts to extend the study to higher silicon concentrations were unsuccessful on account of the transfer of silica from the metal bath to the upper portions of the crucible by means of a silicon-monoxide mechanism. Matoba, Gunji, and Kuwana used similar methods and approached equilibrium from both sides. Their results at three temperatures are shown by the solid lines of Fig. 1. A line corresponding to 1600 deg is interpolated from their equations and is shown by the dotted line. The results of Gokcen and Chipman at 1600 deg in the range 0.02 to 2.0 pct Si are also shown. At concentrations up to about 0.6 pct Si, these investigators approached equilibrium from both directions, and their results in this range appear to be trustworthy. Above 1 pct Si, however, all of their experiments involved oxidation only, as shown by a decrease in the silicon content of the bath. It now seems certain that they failed to reach equilibrium at these higher silicon concentrations and that the curvilinear relation shown by their results is incorrect. It is evident that their results in the lower silicon range are in good agreement with those of Matoba and coworkers. In fact, a straight line drawn through their results would parallel the dotted line and would differ from it by only 0.05 in log K. The new data also lie close to that line. It may thus be concluded that the three sets of data are in good agreement and that the equations proposed by Matoba and coworkers for reaction [2] are satisfactory . They take the limiting value of log K&apos;, at 0 pct Si as log K ,. The slope of each line gives the value

Jan 1, 1962

By Y. Jeannin, C. Mannerskantz, F. D. Richardson

Measurements have been made between 1040o and 1300°C of the equilibrium between chromium metal, chromic oxide, hydrogen, and water. The results are in closer agreement with those deduced from recent thermal data than with previous equilibrium values. They lead to the equation ?G°1300°-1600°k = -266,700 + 59.95T ± 300 cal for the formzation of a mole of Cr2O3 from chromium and oxygen. This same equilibrium has been studied with the chromium dissolved in solid iron, and in this way chromium activities in Fe + Cr alloys have been established. The measuremenis show that there are substantial positive deviations from ideality in the a, and b phases, and support the results obtained by Heymer and Kubaschewski against those of other investigators. There is considerable disagreement between existing data,1"4 which is referred to in the Discussion, concerning the equilibrium Cr2O3 + 3H2 = 2Cr + 3H2O [l] There is also substantial disagreement between the results obtained by various investigators5-&apos; who have measured the activities of chromium in its alloys with iron by the Knudsen effusion vapor pressure method. In view of the importance in metallurgical processes of chromium and its oxide and of Fe-Cr alloys, an attempt has been made to study equilib- rium [I] both with pure chormium metal and with chromium alloyed with iron, at temperatures between 1040o and 1300oC. From the work with the alloys it is possible to derive the chromium activities from the relationship

Jan 1, 1963

By Richard H. Rein, John Chipman

The activity of SiO2, in the entire liquid system SiO2-CaO-Mg0-A12O3 at 1600°C is calculated from the distribution of silicon between these slags and Fe-Si-C alloys saturated with either graphite or silicon carbide, the activity coefficient of silicon in these alloys, and the requisite thermodynamic data. The activities of the other components in the ternary systems SiO2-CaO-A12O3, SiO2-MgO-CaO, SiO2-MgO -A12O3 are computed from these data by the IrON blast-furnace slags can be regarded as consisting of the four major oxide components, SO2, CaO, MgO, and A12O3 along with minor proportions of other oxides and of sulfur. The purpose of this study is to measure the activity of silica in the liquid solutions of these four oxides at iron-making Gibbs-Duhem equation with the aid of the known free energies of several of the interoxide compounds and the accepted phase diagrams. Based on these activities, new data are Presented for the free energy of formation of a number of the interoxide compounds. The free energy of mixing the liquid metasilicates of CaO and MgO shows slight positive deviations from the ideal. temperatures and to obtain activities of the other components by application of the Gibbs-Duhem equation and the properties of several interoxide compounds. Recent investigations on the activity of silica in the SiO2-CaO-A12O3 system1-3 and recogntion of a serious error in older data for the free energy of formation of SiO2 (Ref. 4) have succeeded in bringing a fair degree of concordance into the results of different investigators. In the present study, the activity of silica is obtained from the silicon-distribution experiments described in a previous paper,&apos; the revised activity coefficient of silicon

Jan 1, 1965

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07&apos;, the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By J. Chipman, H. R. Larson

The data previously reported for the quantity as a function of oxygen pressure at 1550°C have been used to compute the activities of Fe, FeO, Fe2O3, and COO in slags of the ternary system. Activities of the first three have been obtained also for two quasi-ternaries involving fixed CaO:SiO2 ratios. IN a previous paper1&apos; the authors reported the results of an investigation into the effects of oxygen pressure on the composition of various simple slags analogous to some of those which are found in steel-making practice. The ratio of ferric iron to total iron was studied at 1550°C in iron oxide melts to which lime, magnesia, lime-plus-silica, and other oxides were added. The oxygen pressures involved those of air, carbon dioxide, and carbon dioxide plus carbon monoxide in several proportions. Although very low oxygen pressures could not be used, the slag-metal equilibrium studies of Fetters and Chip-man&apos; permitted extending the results to slags in equilibrium with iron. For the ternary system CaO-FeO-Fe,O, the oxygen pressure-composition relationship has been determined from zero percent lime to lime saturation over an oxygen pressure range from air to that represented by equilibrium with liquid iron. Lime and silica were added to iron oxide in the ratios 0.54, 1.306, and 2.235 to form three quasi-ternary systems which were also studied over the entire region of liquid melts at 1550°C. Ternary Gibbs-Duhem Equation Wagner" has developed a method by which the activities of two components of a ternary system can be calculated if&apos; the activity of the third component is known throughout the composition range being considered. The fundamental form of the Gibbs-Duhem equation for ternary systems is N, d In a, + N2 d In a, + N3 d In a3 — 0. Wagner has developed a usable form of this equation by introducing the term y = N3/(N3 + N1) and rearranging the equation to give (? In a1/?N2)x = -y/(1-N2)2 (? In a2/?y) x2 N2/1-N2 (? In a2/?N2) y To apply this equation to the slag system CaO-FeO-Fe,O,, the activity of one of these components must be known. However, the only activity which is known from the experimental data is the activity or pressure of oxygen in the gas phase with which the slag is in equilibrium. The activity of oxygen in the slag can be defined as the square root of the oxygen pressure. In order to use oxygen as one component, the composition of the slags must be converted to the basis Fe-O-CaO. Oxygen, exclu-sive of that contained in CaO, then becomes com-ponent 2 in Eq. 1, Fe is selected as 1 and CaO as 3. Then y = Ncao/(Ncao + NFe). Eq. 1 then becomes (? In a fe/? Nx) y = -y/(1-No)2 (? In ao/?y) xp - No/ 1- No (? In ao/ O No) y. In order to evaluate Eq. 2, the boundary conditions must be known. The obvious choice of a standard state for iron is to assign slags in equilibrium with iron an activity of one. Then In a,., or log aFe, which is substituted for convenience, is determined by integrating along a line of constant y from the slag in equilibrium with iron to the composition at which log a,, is to be determined. Mathematically this can be expressed as log aFe (Nlog y) = log a&apos;Fe + (? log a Fe/? No) dNo where the primes indicate equilibrium with liquid iron and a&apos;Fe = 1. When Eq. 3 is integrated along a line of constant y, the following is obtained: log a Fe (No, y) = - y No ?/ No ? y ( log ao/(1- No)2) No d No - No/1-No d log ao. Lime-Iron Oxide Slags Iron Activity: The oxygen pressure of lime-iron oxide slags is shown in Fig. 1 as a function of j, de-fined as j = Fe+++/(Fe++ + Fe +++) for various constant mol percentages of lime. The j values at 0 to 60 pct lime were then determined for oxygen pressures of 1, 10-1, etc. to 10-" atm. For purposes of calculation, the line for zero percent lime was extrapolated to

Jan 1, 1955