Search Documents

By A. J. Burger, F. L. D. Cloete

Tests indicated that effective recovery of pyrite from a coarse Witwatersrand quartzitic ore can be accomplished by intensified flotation in an air-sparged hydrocyclone. Air is fed through the porous cylindrical wall of the hydrocyclone into a swirling layer of slury. Hydrophobic particles are attached selectively to small air bubbles, which form a froth and are recovered through the overflow. Hydrophilic particles pass out in the underflow. A spigot in which flow is restricted by an orifice was found to be more successful in preventing blockage by wood chips than an annular opening between a pedestal and the cylinder wall. Pyrite recoveries of 85 to 93 per cent at grades of 35 to 40 per cent sulphur were obtained in the air-sparged hydroclone with residence times of about 1 second. Comparative tests in a batch flotation cell after 320 seconds yielded average recoveries of up to 96 per cent, but with a mean grade of 32,5 per cent sulphur. A high colector dosage of 120 g/t was required in the cyclone, compared with the 40 gft used in conventional operations. An air flowrate of about 150 I/min was adequate at a slury feed rate of 35l/min. Particle sizes between 38 and 106µm yielded the best flotation results.

Jan 1, 1988

By Bin Xu, Qian Li, Xishan Li, Yongbin Yang, Hongwei Li, Tao Jiang, Yan Zhang

The cyanide leaching rate of gold from a multi-refractory gold concentrate (18.05 g/t Au) containing 1.62% As, 20.76% S, 6.95% C and 1.31% Sb was only 1.33%. The enhancement of gold leaching was studied mainly by the pretreatment of oxidative roasting and alkaline sulfide washing. Results showed that after the two-stage roasting (i.e., I stage of 500 °C, 1 h and II stage of 700 °C, 2 h) most of sulfur (93.84%) and carbon (98.27%) were removed, but the gold leaching rate of calcine just reached 71.33% because the residual arsenic (0.63%) and antimony (1.15%) were still high. After alkaline sulfide (i.e., NaOH and Na2S) washing, the residual arsenic and antimony was further decreased to 0.21 and 0.65%, respectively. The gold leaching rate of the treated calcine by cyanidation could increase to 93.52% substantially. Also, the optimized particle size, NaCN concentration and leaching time were −0.045 mm over 85%, 0.1% and 36 h, respectively.

Mar 1, 2017

By V. A. Masloboev, A. V. Svetlov, D. V. Makarov

"The methods of heap leaching are considered to be the most promising for the low-grade copper-nickel raw materials. The article presents intensification capabilities of the process. Objects of research: the low-grade copper-nickel ores of Moncheplutone deposits (Moroshkovoye Lake, Nyud Terrasa, Nittis-Kumuzh’ya-Travyanaya (NKT), as well as the copper-nickel ore dressing tailings of the “Kola MMC” JSC. The following directions for the intensification of the low-grade copper-nickel raw materials heap leaching have been considered: preliminary electric pulse destruction (EPD) of ore; ore crushing and further sulfuric acid agglomeration. The impact of sulfuric acid concentration (1-3%) on the extraction of non-ferrous metals kinetics from the copper-nickel ore dressing tailings under various conditions of the percolation leaching has been studied. INTRODUCTION The low-grade grade sulfide ores at the abandoned and producing deposits, overburden rocks, mill tailings and non-ferrous slag are thought to be one of the large-scale sources for non-ferrous metals, on the one hand. On the other hand, they are known to be the subjects of emergency environmental danger. For this reason, the use of mine dumps and tailings, as well as the remained ores left in the ground as raw products, and at the same time decreasing the load on environment, are considered to be the pressing ecological and economic issue (Chanturia et al., 2012). Methods of heap hydrometallurgical and bacterial leaching are sure to be potentially productive for processing such low-grade and technogenic raw materials (Petersen, 2016). The early studies of hydrometallurgical method possibility to process copper-nickel ores of the Murmansk region deposits were launched in the seventies of the previous century (Golovko et al., 1978). For referencing purposes, the main types of impregnated ores from the deposits Zhdanovskoye, Kaula, Sopchinsky Plast and Lovnoozerskoye were selected. The metal content varied, as %: 0.46-1.49 of nickel, 0.01-0.62 of copper. In the first experiments, the solution containing 150g/l of H2SO4 and 135g/l of NaCl, was used in the capacity of leaching reagent. The possibility of underground metals leaching from the ores of the Lovnoozerskoye deposit was justified due to the performed laboratory and further large-sized tests."

Jan 1, 2018

By Valery V. Kostjuk, Victor. N. Bredikhin, Alexander I. Shevelev, Evgeny A. Kazban

"The investigations to improve the process data have been done in order to stabilize the functioning of drying units. The scheme of turnings preparation with centrifuging and subsequent thermal degreasing (tandem) is proposed. To improve the efficiency of the process the scheme of reclamation of the centrifuge fugate is developed with production of oil and service circulating water. Empirical dependences of the turnings temperature influence on the lubricant-coolants content in centrifuging are gained. When the turnings temperature is increased to 80 C the residual content of LC is decreased by 1.5%. The investigations aimed to improve the preparation of non-ferrous turnings have allowed to decrease the melting loss by 15-20%; to stabilize the process of thermal drying of turnings; to decrease sharply (by 60- 70%) the volume of LC combustion products; to reclaim the centrifuge fugate and produce oil and servicecirculating water.Non-ferrous turning and primarily aluminum and copper alloys turning is a stable source of secondary raw materials for metallurgical works.Direct by lubricant-coolants (LC) of various types: synthetic, semi synthetic, oily and emulsions.On the base of investigations concerning various methods of the non-ferrous turning processing the favorable one has been selected taking in to consideration the economy, ecology and quality of the finished product (alloy). Two-stage process is developed. The main idea of the process is the elimination of the lubricant-coolants (LC) to the limit specified in advance. The applied method is centrifuging with subsequent final elimination of LC by thermal method.Constant value of LC content at the inlet of the thermal unit excludes practically the oxidation of metal and as a consequence increases the output by 10 –15 % in metallurgical processing."

Jan 1, 2003

By G. G. Richards, Y. Oyediran, V. Chow

The oxygen softening process for partial removal of arsenic and antimony from lead bullion has been in use at Teck Cominco's Trail smelter since 1986. In this process, industrial oxygen is injected into bullion to remove As and Sb with the formation of an oxide slag. In Trail, the levels of these elements are reduced to concentrations suitable for processing in the Betts electrorefining plant. Recent moves toward the treatment of higher arsenic-bearing feeds have necessitated an increase in the process capacity to meet the specifications for drossing plant bullion. Process intensification trials were conducted in-plant to develop an operating strategy for higher bullion processing rates. This was preceded by a study conducted with McGill University to develop a fundamental understanding of the therm ochemistry and kinetics of the process. The results have yielded more effective control of the operation, and identified opportunities for further improvements.

Jan 1, 2008

By Lane D. P, Malone J. G

The slag fuming furnaces are the major bottleneck in the BHAS zinc production flowsheet. Intensification of the fuming process could significantly reduce this production restriction. Oxygen enrichment was proven to be a means of intensifying the fuming process. This procedure resulted in higher slag bath temperatures, and development work was undertaken towards obtaining accurate slag bath temperature measurement and control. Slag bath temperature measurement techniques were evaluated, with infra red optical pyrometry established as the system with the most potential for continuous temperature measurement and control. Oxygen enrichment resulted in a zinc production capacity increase of 1 000 tonnes per year. An oxygen enrichment technique was developed which both minimized the risk of furnace damage and made the most efficient use of the enrichment oxygen.

Jan 1, 1989

By Rodrigo Martins, Mauro Trindade

I Reduction of energy consumption in air compressors by the implementation of individualized load control. Reduction of 3,5% from Jun / 18.

Oct 3, 2019

By C Zhang, I Canbulat, G Fan, D Zhang, C Wang

A clear understanding of the intensity of coal and rock burst is the basis for future research on burst mechanism and control. There has been a wide variety in the description of coal and rock burst damage at different countries using multi-methods, which makes the common understanding even more challenging. Therefore, this paper presents a broad review on the quantifications of intensity of coal and rock burst and seismic risk around the world, considering critical factors including seismic energy, magnitude, peak particle velocity and ejection velocity. It is found that the seismic energy of coal and rock burst can widely range from 0.002 MJ to 60000 MJ, with equivalent Richter magnitude from -1 to 4. The daily seismic energies can be used for seismic risk potential assessment, with energy levels from 0.1 KJ to 10 MJ, which is much lower than the burst sources. The magnitude of the seismic events can be also estimated based on the weight of damaged coal mass and human senses of vibration and sound. For the seismic intensity represented by peak particle velocity (ppv), it keeps constant within fault radius and attenuates with a speed of 1/r4 and 1/r in near and far field respectively, thus it is possible for a small seismic event to induce considerable ppv causing severe damage if the epicentral distance is small enough. There has not been a strong correlation between the ejection velocity and ppv, as seismic energy is only one of the energy sources that contribute to the kinetic energy of burst damage. CITATION:Wang, C, Zhang, C, Canbulat, I, Zhang, D and Fan, G, 2018. Intensity quantification of coal and rock burst risk – a review, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 223–233 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

THE Wonthaggi coal-field lies south easterly from Melbourne at a distance by rail of 86 miles, on the flats of the Powlett River, immediately to the south of the deep-cut valleys and steep intervening ridges in the Jurassic rocks of the Bass Range and itsfoot-hills. The coal-bearing area is covered with a thin layer of late Tertiary and Recent deposits, which serve to mask the true character of the underlying coal-bearing rocks and effectually prevent the appearance of any coal outcrop. Two or three bores sunk prior to 1890 had shown the locality to be really a potential coal-bearing one. Only one additional bore was sunk in the State Coal Mine area until 1908, when energetic boring was resumed, with the result that in November, 1909, when an acute shortage of black coal in Victoria resulted from the prolonged strike on the New South Wales coal-fields, coal-seams had been located at Wonthaggi offering sufficient inducement to start an...

Jan 1, 1918

This paper describes the operating practice and design features of an intensive-cyanidation plant at the East Gold Plant of Vaal Reefs Exploration and Mining Company Limited (V.R.E.M.). After the development oh cyanidation route for the treatment of gold-plant gravity concentrates by the Anglo American Research laboratories (A.A.R.L.), a full scale plant was commissioned at Western Holdings (Welkom Division) Gold Mine in March 1977, and the V.R.E.M. plant was commissioned in August 1981. Although the gravity-concentration route does not now enjoy the prominence of former times, in an existing conventional plant the intensive-cyanidation route can successfully replace mercury amalgamation.

Jan 1, 1984

By A. Warczok

Metal losses in discard slag are the main factor determining overall recovery. The metals are present both in dissolved form and as matte or metallic inclusions, varying in size from 2 to 1000 µm. Pyrometallurgical slag cleaning usually consists of heating the slag, reduction of oxides and settling of matte/metal droplets. Heating the slag decreases viscosity and accelerates reactions. Reduction of magnetite liberates inclusions and facilitates co-reduction of dissolved metal oxides. A significant amount of the matte and metal is present as very fine metallic inclusions, too small for settling. The coalescence of these matte or metal inclusions is required to remove them from the slag. The developed new concept of slag cleaning combines DC furnace technology with an extra magnetic field for vigorous slag stirring, enhancing mass transfer to the reductant surface, accelerating the rate of reduction, and destabilizing the emulsion of matte or metal inclusions. Intensive slag stirring increases the probability of collision of inclusions, will accelerate their growth and will therefore improve settling. The process is carried out in a patented DC channel furnace, where the liquid metal or matte layer acts as a cathode and the floating coke bed on the slag surface is the anode. In the first part of the furnace, a superimposed magnetic field induces a Lorentz's force causing the slag to start an intensive circular motion. The next furnace zone does not experience any stirring and is dedicated for quiet sedimentation of the inclusions. A mathematical model of gravitational coalescence combined with forced slag motion showed the possibilities of effective removal of copper matte inclusions. The results of laboratory pilot scale tests of continuous slag cleaning showed fast slag reduction and confirmed the improved matte removal from the slag. Conceptual analysis shows the potential use of the technology in various other non-ferrous industries, like for example nickel plants. It is also possible to use this technique batch wise.

Jan 1, 2007

By Henry Gross

RECENTLY, areas of abnormal rock pressure have been drilled on the Gulf Coast of the United States. These pressures may be caused by the recent and pronounced raising of some of the structures without loss of the formation pressure that existed when the reservoir was developing and the producing sand much more deeply buried. It is possible also that a permeable fissure may connect a shallow accumulation of gas with the gas cap of a much deeper reservoir of oil, gas and water. The pressures are so great that dependence on blowout-prevention equipment alone is hazardous to life and property. Fortunately, wells with excessive casing-head pressures, such as the Stanolind Oates No. 1 of the South Houston field, an 8700-ft. gas well with 6000 lb. per sq. in., and the near-by Stanolind Candelari No. 1, and 8100-ft. gas well with 5000 lb. per sq. in., have not blown out and cratered. A case is on record of drill pipe in a, well in Harris County, Texas, (Oates No. 1) rotating for 8 hr. through blowout-prevention rants holding a back pressure of 2900 1b. per sq. in. at the casinghead after the mud was altered by salt-water intrusion. Such conditions warrant the use of extremely heavy muds having low viscosity, made from galena (PbS) or specially prepared mixtures of hematite (Fe203) and galena suspended by bentonite. In some Gulf Coast wells, sodium silicate mixed with concentrated brine is used to drill through heaving shale formations. Such a fluid inhibits heaving remarkably, but it is expensive and costs as much as $10 per barrel. Barite has been used to weight this mixture. However, this mineral too rapidly increased an already excessive viscosity and it was thought that galena might be better for weighting such drilling fluid. The operator was anxious to try the latter, but none was available in the district.

Jan 1, 1938

By Charles A. Thomson

RECENTLY a prominent Brazilian' doctor wrote to an American friend: "I feel that cultural relations between the American and Brazilian people could be promoted in a very speedy and effective way by establishing contacts between men of the same professions. . . . A Brazilian mechanical engineer could be immediately interested in relations with American colleagues, even if he had never heard of Longfellow and was not interested in Stokowski's orchestra. . . . A large number of cultural ties could be established between specific groups of men who have already some common interest, and who, whenever they meet, can do something that naturally brings them closer, that is, `talk shop."' In appointing a committee on Inter-American Engineering Relations to cooperate with the Department of State in its program of fostering cultural relations with the other republics of this hemisphere, the American Engineering Council has taken a step which should lead to a greater sense of unity and fraternity among engineers of the Americas. That such unity and fraternity are part and parcel of the moral defense of the hemisphere is obvious. For years engineers of the United States have been traveling South and South-east to construct roads and bridges, dam rivers, harness waterfalls, build ports, install and operate mining equipment, and erect buildings and plants, often at the risk of life. Those in the teaching profession in this country have had as pupils a growing number of students from our neighboring republics whom they have sent back home trained in the most efficient engineering methods. In a sense, however, these relations with the other nations on this side of the globe have been haphazard and left to chance. Personal acquaintance among engineers has played its role but no organized attempt appears to have been made to take advantage of the natural relationship which geographical and historical factors should encourage.

Jan 1, 1940

By Renee Grogan

"An environmental impact assessment (EIA) of a deep sea mining project typically describes the environmental baseline, impacts of the project to the environmental values, and proposed management techniques. Comprehensive EIAs also consider the impact of the mining project on existing industries, including deep sea fishing. However, few projects to date have included other industries in the EIA process in more than a cursory manner, due to the confidentiality of the process, conflicting priorities, and bureaucratic limitation. However, if the United Nations Sustainable Development Goals (particularly Goal 17: Collaboration) are to be achieved, a new way of thinking will be necessary for deep sea mining projects, starting with collaboration at the very beginning of the project life cycle.STRUCTURE OF PRESENTATIONThis presentation will be in the format of an oral (20 minute presentation).The presentation will cover the process of inter-industry collaboration throughout the life cycle of a deep sea mining project, drawing on historical and existing examples, including that of the Chatham Rock Phosphate Project in New Zealand."

Jan 1, 2017

By David L. Anderson

"The objective of this paper is to describe the potential impact of inter-provincial competition f or new output capacity on the Canadian potash industry. It will be shown that the ramifications of such actions are potentially severe, especially since the potash industry is one of the few non-fuel minerals in which Canada purportedly possesses a significant degree of market power. More specifically, the paper addresses the impact of possible expansions in New Brunswick, Manitoba and, perhaps, Saskatchewan. The findings suggest that such initiatives could result in substantial excess capacity and the dissipation of monopoly rents. In summary, given the market structure of the industry, it is unlikely that the employment and economic effects associated with industry expansion will offset the loss in national welfare attributable to rent dissipation.IntroductionThe objective of this paper is to discuss the potential impact of inter-provincial competition for new output capacity on the Canadian potash industry. The ramifications of such competition are potentially severe: given that the potash industry is one of the few non-fuel minerals in which we purportedly possess a significant degree of market power(1), it is important that sound supply management practices are followed. However, possible initiatives by New Brunswick, Manitoba and, perhaps, Saskatchewan may initiate an inter-provincial competition which could result in substantial excess capacity and the dissipation of economic rents(2). Given the market structure of the industry, it is not intuitively obvious that the employment and economic effects associated with industry expansion will offset the loss in national welfare attributable to rent dissipation."

Jan 1, 1985

Mine site rehabilitation is the repair of the disturbance caused by mining on the immediate mining area and also on the surrounding environment. The long-term objectives of rehabilitation can vary from simply returning an area to a safe and stable condition, to restoring the mined land to a state as close as possible to its pre-mining condition, capable of being self-supporting and having a beneficial final land use. This paper investigates the importance and benefits of environmental planning, in particular for rehabilitation, and how input into daily operations can allow mining to progress with limited impact on the surrounding environment. It will also identify some of the key mistakes currently made during mining which could be averted by implementing prior planning and incorporating environmental consideration into daily operations. A number of rehabilitation opportunities will also be detailed for the different stages of the life cycle of a coal mine.

Jan 1, 2007

By J. C. Stankus

How to quantitatively identify the loads on a square/arch set is a complicated issue in designing the square/arch set in an intersection/entry. From an engineering perspective, understanding the nature and support mechanism of standing support such as a square/arch set can not only help design the support structure to maintain the roof stability, but save the steel materials and costs of manufacturing, labor, and delivery. Based on the design practices in recent years and successful applications in slope bottom intersections, the authors are confident that the concept of interaction and confinement effect between the steel square/arch set and surrounding rocks is critical in designing a proper steel structure to support an intersection/entry. This paper will detail the design concept and its applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.

Feb 23, 2014

While reaction to immediate demands may be required from time to time, the principal concerns of a Geological 'Survey should be proaction, with respect to the systematic production of maps, reports and data in order to meet exploration needs in the longer term, and interaction, which involves a complex matrix of relationships - firstly within the Department between disciplines and at various levels of responsibility, secondly with the exploration industry, thirdly with Commonwealth authorities particularly the Bureau of Mineral Resources (BMR), and fourthly with university researchers in related fields.

Jan 1, 1987

By C. Ernest Birchenall

As a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.1 In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in. the preceding paper.2 A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken .3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity data given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below.

Jan 1, 1947

By L. Salinas

Lance injection of gas and particles into a molten bath is currently practised in metallurgical processes (Mitsubishi lances for example). Several experimental and theorical studies have been conducted in the past on this topic. However, neither detailed calculations nor experimental studies of local flow patterns have been published. In the present work, a numerical simulation of the interaction of a gaseous vertical descending jet and a liquid surface was done, using the turbulence k-e model. There is a fair agreement between the calculated and the experimental values. The results of this study demonstrate that it is crucial that the gas jet velocity profile and turbulent characteristic are correctly formulated in order to correctly simulate the system.

Jan 1, 1999