Search Documents

By J. P. Sheeha, W. F. Craig, M. Baeyertz

The loss in toughness caused by phosphorus within commercial ranges was studied in AISI-SAE 1340 steel and in molybdenum modifications of this grade. The replacement of part of the manganese by molybdenum in amounts which maintain the hardenability of the standard 1340 grade was shown to counteract to a marked degree the detrimental effects of phosphorus. THIS paper deals with the effect of phosphorus on the toughness of 1340 steel and with the effect on toughness of replacing part of the manganese by molybdenum while retaining the same hardenability as that of 1340. In previous work1 a progressive decrease in toughness was observed when the phosphorus content of 5140 was raised from 0.020 to 0.036 pct; that is, from a moderate phosphorus level to one higher but yet within the AISI-SAE specification for this grade. The structural condition of the steel was tempered martensite. Toughness was evaluated by the transition temperature determined by V-notch Charpy tests. Replacement of a part of the chromium in 5140 by molybdenum provided a factor of safety against loss of toughness caused by phosphorus, especially where the steel was cooled slowly after tempering. Scope of the Study: In view of the improved tolerance for phosphorus obtained by replacing a part of the chromium in 5140 with molybdenum, it seemed desirable to investigate the possibility of obtaining similar improvement in 1340 by replacing part of the manganese with molybdenum. Heats were made at different phosphorus levels, in a series that began with 1340 and ended with steels containing 0.32 to 0.35 pct Mo with 0.82 and 0.90 pct Mn. The analyses of the heats are given in table I. In order to facilitate later discussion, the 1340 heats have been placed together in the order of increasing phosphorus content, and the molybdenum modifications have been grouped according to phosphorus

Jan 1, 1951

By A. R. Elsea, C. C. McBride

HIGH-TEMPERATURE alloys, that is, alloys that are strong at high temperatures, have become increasingly important with the development of modern aircraft engines. Many alloys of this type are available. However, metallurgists do not have a clear understanding of the phases or structures which are responsible for these high-temperature properties. If these basic factors were understood, it might be possible to make better or cheaper alloys for service at high temperatures. For this reason, an investigation of the fundamental factors promoting high-temperature strength in alloys was started at Battelle Memorial Institute. This was to have included a study of the relationship between the structure and properties of cobalt-chromium base alloys of the vitallium type. It soon became clear that the structure of vitallium is quite complex and that the equilibrium diagrams which should explain these structures were unreliable. As a result, the cobalt-chromium binary diagram was determined as the first phase of this investigation1. This diagram is shown in fig. 1. During the study of the cobalt-chromium binary system, it was learned that these alloys may pick up considerable nitrogen when melted and heat treated in air. The extent to which nitrogen affects the various reactions in cobalt-chromium base alloys was not known, but there were indications that this impurity might be responsible for some of the erratic test results obtained for vitallium. Consequently, nitrogen was the first ternary addition studied. Thereafter the work was extended to ternary additions of iron and of nickel. This paper describes the investigation of the effects of nitrogen, iron, and nickel upon the reactions in cobalt-chromium alloys with 80:20 and 68:32 cobalt-chromium ratios. Experimental Work Alloy Preparation: A series of cobalt-chromium base alloys containing various amounts of the third element being studied were made for both the 80:20 and the 68:32 cobalt-chromium ratios. Electrolytic chromium, cobalt, and iron, and reagent-grade nickel powder were used as melting stock. Table I contains the chemical analyses of these materials. The charges were melted in alun-dum thimble crucibles which absorbed chromium oxide and effectively deoxidized the melts. These crucibles were supported by close-fitting graphite sleeves so that if they cracked during melting the metal would not be lost. Carbon increases, during

Jan 1, 1951

By P. Beardmore, A. H. Holtzman, M. B. Bever

Specimens of the alloy CU3AU in the ordered and disordered states were subjected to explosive loading at shock pressures in the range from 160 to 475 kbars. The resulting changes in the resistivity, stored energy, microhardness, and microstructure were determined. By comparing the effects of explosive loading on ordered and disordered specimens a separation of structura1 and configurational changes has been made. In the pressure range from 290 to 370 kbars, representing a small increment of strain, the degree of long-range order in the ordered alloy decreased sharply. This change is attributed to the generation of shear stresses in excess of the theoretical shear strength of the alloy. Disordered CU3AU under explosive loading behaves in a manner considered to be characteristic of fee solid-solution alloys generally. The response of metals to high-velocity deformation and, in particular, to explosive loading has attracted much interest in recent years.' In general, metals are substantially strengthened by the passage of shock waves although the permanent strains are small. Explosive loading induces this strengthening by causing the metal to undergo rapidly a transient strain in a narrow region, first in the shock front and then in the rarefaction wave, which releases the pressure. The transient strain is given by e = 4/3 In V/Vo, where Vo and v are the specific volumes in the uncompressed and compressed states.2 The process produces many defects, which account for the strengthening. For the investigation reported here, an ordered alloy was chosen because it was expected to give sensitive indications of the near-neighbor effects produced by shock waves. The ordered alloy CU3AU was of special interest because of past work on the effects of conventional deformation on this alloy.314 The disordered alloy was included as a standard for comparison and as an alloy typical of a solid solution containing short-range order. The effects of explosive loading were followed by measurements of the resistivity, stored energy, and microhardness, and by metallographic examination. EXPERIMENTAL PROCEDURES Preparation of Specimens. Part of an ingot of the alloy Cu3Au prepared previously4 was cold-rolled with several intermediate anneals in vacuum to a final thickness of 0.042 in. Specimens of dimensions 2.0 by 1.0 by 0.042 in. were machined from this strip. After a recrystallization treatment of 1 hr at 565oC, half of the specimens were disordered by heating in evacuated Pyrex capsules for 1 hr at 460°C and quenching into water. Although they contained short-range order, they will be referred to as 'disordered" to indicate the absence of long-range order. The rest of the specimens were cooled slowly from 380°C to induce long-range order. The grain size of the ordered and disordered specimens was 0.012 mm. Explosive Loading. This was carried out at the Eastern Laboratory, Explosives Department, E. I. du Pont de Nemours & Co., by a driver-plate procedure described elsewhere.2 Two ordered specimens were stacked alongside two disordered speci-

Jan 1, 1964

By I. J. Polmear

Earlier work revealed that small amounts of silver (< 0,l at. pct) may exert a marked effect on the structure and aging characteristics of certain a1loys based on the Al-Zn-Mg system. Silver additions have now been made to other age-hardening aluminum alloys, and significant effects have been observed in the Al-Mg system and in several Al-Cu-Mg and Al-Mg-Si alloys. Similarities exist between the behavior of alloys from all four systems, notably that in each case silver stimulates nucleation of an intermediate precipitate which forms when the alloys are aged in the medium temperature range (-120" to 220°C). The mechanism for this effect is uncer- IT has been shown that small additions of silver (<0.1 at. pct) may have a marked effect on the structure and age-hardening characteristics of tain although it is suggested it originates in a preferred affinity between magnesium and silver atoms. There is evidence to indicate that the effects of silver are unique to that element. It is suggested that silver atoms interact with vacancies during low-temperature aging of Al-4 pct Cu and certain Al-Cu-Mg alloys. Silver had little effect on Al-8 pct Zn aged at any temperature. Preliminary observations indicate that silver may have interesting effects on the strength properties of Al-Mg alloys, md a the commercial Al-Cu-Mg alloys designated as 2024 and 2618. many alloys based on the Al-Zn-Mg* system.1"&apos;*

Jan 1, 1964

By L. S. Richardson, N. J. Grant

Iodide-grade titanium, two oxygen alloys, and two aluminum alloys were studied by means of creep-rupture tests from 1000° to 2000°F. From the test information an evaluation was made of, 1) the relative creep-rupture strengths of the u (hexagonal-close-packed) and 0 (body-centered-cubic) forms of titanium and some of its alloys; 2) the effects of solid-solution strengthening by oxygen and aluminum on the u and 0 structures; and 3) the extent and effect of atmospheric oxygen alloying on rupture life in tests above about 1000°F. THE use of titanium alloys at temperatures above 1000° F has been considered unlikely by most investigators because of low creep strength (based on a requirement for room-temperature ductility, formability, and weldability) and low oxidation resistance. The results of this testing program do not entirely uphold this pessimism in terms of strength and oxidation resistance. The observations described below are based entirely on stress-rupture results, although some creep tests were also carried out on these alloys. Three items of primary importance are covered: 1) Stress-rupture data in the form of the Larson-Miller parameter curves for several titanium alloys at temperatures up to 2000°F; 2) The relative strengths of the hexagonal-close-packed a structure and the body-centered-cubic 0 structure; 3) The effects of solid-solution alloying on the creep-rupture properties of titaniu&apos;m at elevated temperatures. Only two investigatons have reported the creep- rupture properties of titanium at temperatures above 1000° F. Lunsford and rant&apos; tested iodide titanium; their values are also utilized in the paper. EXPERIMENTAL PROCEDURE After a few tests had been made in a conventional creep-rupture test machine, it became clear that some sort of atmospheric protection would be necessary for short-time tests conducted at temperatures above 1600°F, or for times greater than 100 hr at 1200°F or above. Several furnace units and test machines were constructed, the most successful of which is shown in Fig. 1. Certain experimental difficulties peculiar to titanium were encountered; for example, the use of molybdenum holders was dictated because titanium forms low melting-point eutectics with conventional high-temperature alloys containing appreciable amounts of iron, nickel, or cobalt. This same difficulty made the use of chrome l-alumel thermocouples in direct contact with a test specimen impossible, above about 1500" F. The high-temperature high-vacuum furnace shown in Fig. 1 was capable of maintaining a vacuum of better than 10"5 mm of mercury at 2000°F (pressure measured in cold part of system) and 5 X lo-&apos; mm at room temperature. Most of the tests eonducted in vacuum were at temperatures

Jan 1, 1960

By R. B. G. Yeo

The effects of alloy additions on the M, and A, temperatures of an Fe-22.5 pct Ni alloy have been determined. Increasing amounts of titanium, colum-bium, vanadium, and silicon raise and then lower M,while raising A, cmtinuously. Cobalt raises both M, and A,. Aluminum has little effect on Ms but raises A,. Chromium md nickel lower M, and A,. It is proposed that elements raise M, in accordance with their effect on the Ae3 temperature of iron until the lattice becomes stiffened against the shear transformation so that M, is then lowered. An anomaly, first pointed out by Zener,1 arises in steels when the addition of elements, such as molybdenum and tungsten, which raise the Ae3 temperature, also lower the M, temperature.2&apos;3 During the development of a series of martensitic precipitation-hardening (maraging) steels, the effect of several elements on the transformation of austenite to martensite was studied. The results show that under suitable conditions several elements which raise Ae3 also raise the M, and A, temperatures. PREPARATION OF MATERIALS STUDIED A series of alloys was made in which cobalt, titanium, columbium, vanadium, silicon, aluminum, molybdenum, chromium, and nickel were added to an iron base containing 22.5 pct Ni. The compositions of the alloys prepared are given in Table I. The residual manganese contents of the heats were in the range of 0.030 to 0.35 pct, silicon 0.05 to 0.1 pct, carbon 0.0008 to 0.009 pct, and nitrogen from 0 to 0.004 uct. The allois were made as 50-lb induction heats starting with electro-iron and electro-nickel, melted in air to oxidize impurities. Additions of silico-manganese and ferro-silicon were made after which the power was turned off to allow the products of deoxidation to rise and be skimmed from the surface of the melt. The furnace chamber was pumped down to a pressure of 5 p and the charge was heated to 2900°F for the addition of other alloying elements. The heats were poured into five 10-lb ingots, making successive alloy additions to each. The ingots were soaked for 2 hr at 2300°F and hot-worked to 3/4-in.-diam bars. This stock was heated to 1500°F for 1

Jan 1, 1963

By N. J. Grant, Masao Adachi

A number of Cu-SiO, and Cu-A1203 alloys of low oxide content, produced by internal oxidation of copper-silicon and copper-aluminum dilute solid solutions, were exposed at temperatures up to 1050°C for fairly long times to bring about partial or total re crystallization. The creep-rupture properties of these re crystallized alloys were compared to those in the as-extruded condition at 450° C. Some of the alloys were cold worked after re crystallization to note changes in creep-rupture properties, also at 450OC. SINCE the introduction of the SAP alloy in 1949,~ many studies have been carried out on similar oxide and intermetallic dispersion hardened alloys to determine properties and to establish the mechanisms involved in the strengthening process which led to stable, high-temperature behavior.&apos;-&apos; To date, it has been indicated that, however achieved, the structure should be composed of a continuous ductile metal matrix in which is dispersed a fine, submicron size, hard, insoluble second phase (or at least, essentially insoluble at temperatures very near the melting point), with a submicron or near submicron interparticle spacing. Stored energy, obtained by a high strain rate deformation process appears desirable, as an additional strengthening means beyond pure dispersion.=

Jan 1, 1961

By R. H. Frazier, J. M. Hodge, F. W. Boulger

This paper reports the results of studies of the impact properties of quenched and tempered alloy-steel plates as a function of sulfur content. It was found that the impact energy levels decreased continuously as the sulfur content increased and that there was a straight-line relationship between impact energy and sulfur content when plotted on logarithmic coordinates. Cross rolling raised the level of these Lines for transverse tests and lowered the level for logitudinal tests proportionately to the amount of cross rolling. ALTHOUGH it has been generally recognized that, for applications in which notch toughness is critical, the sulfur content of the steels used should be held to a low value, quantitative information on the effect of sulfur on notch toughness has not been available. For such applications, it is a common practice to specify minimum impact values, and in order that these may be met consistently it is important that the steel producer know quantitatively the effect of sulfur on notch toughness so that realistic sulfur content limits can be applied to the steels they produce. In many instances, particularly in flat-rolled products, impact properties are specified in the direction transverse to the principal rolling direction, so that the factors affecting the anisotropy or directionality of impact properties are also of concern to the steel producer. For some applications, furthermore, it is a common practice to increase the sulfur content of steels in order to improve their machinability, and, in such instances, the effect of this practice on notch toughness may often be of concern. This paper reports on an investigation, carried out at Battelle Memorial Institute, designed to furnish this quantitative information on the effect of sulfur on notch toughness and also to furnish further information on the factors affecting the anisotropy of impact properties in wrought heat-treated alloy steels. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental steels were of intended base analysis: 0.30 pct C, 0.80 pct Mn, 0.25 pct Si, 2.5 pct Ni, 0.80 pct Cr, and 0.45 pct Mo. Steels were made with sulfur contents varying from 0.005 to 0.179 pct. The steels were prepared from 600-lb induction-furnace melts. Steels containing 0.020 pct or more sulfur (at meltdown) were melted from a charge of ingot iron (except for one heat): lower-sulfur steels were made from electrolytic iron. The charge consisted of ingot or electrolytic iron, ferrosilicon to give 0.10 pct Si, and ferromanganese to give 0.05 pct Mn. At meltdown, electrolytic nickel, ferromolybdenum, iron phosphide, and pyrite were added followed in sequence by ferrochromium, sili-comanganese, ferrosilicon, and ferromanganese. The slag was then removed and graphite added to give the desired carbon content. Bath temperature was adjusted to 2850°F and, when no other additions were to follow, 2 lb per ton of aluminum was added, immediately before tapping. Compositions of the experimental steels appear in Table I. Analyses are from single determinations, except sulfur which was analyzed in duplicate. A test sample (3 in. in diam by 6 in. long) and a 575-1b ingot were poured from each heat. The test sample was poured in a sand mold; the cooling rates of the test sample and the large ingot were approximately the same. Chemical analysis chips and metal lographic specimens were taken from the test samples. The ingot was 8 in. sq at the base and 9 in. sq at the top. A 5 X 5 X 6-in. sand mold hot top was completely filled in teeming the ingot. After solidification, the mold was stripped from the ingot which cooled to room temperature. Ingots were reheated to 2250"F and rolled to 1.9-in. slabs on a commercial mill. The slabs were box-cooled to room temperature. Sections of the 1.9-in. slabs were heated to 2250°F and rolled on a Battelle laboratory mill according to one of three schedules: 1) rolled straightaway to 0.5-in. plate; 2) rolled straightaway to 1.3-in. thickness, then cross rolled to 0.5-in. plate (29 pct cross rolling); or 3) cross rolled from 1.9-in. to 0.5-in.-thick plate (46 pct cross rolling). The 0.5-in.-straight- or cross-rolled plates were normalized at 1700°F for 1 hr and then water quenched from 1600°F. Plates were then tempered 2 hr at 1240°, 1170°, 1080°, or 860°F to obtain Rockwell C hardness of 25, 30, 35, and 40, respectively. Tempering was followed by quenching to room temperature to avoid temper embrittlement. Slack-quenched plates were isothermally transformed for 26 min at 800°F, quenched, and tempered 2 hr at 1170°F. Pearlitic microstructures were obtained by holding 168 hr at 1200° F, followed by quenching. Charpy V-notch specimens were taken both transverse and longitudinal to the main rolling direction, notched perpendicular to the plate surface, and tested. Slabs and plates which were to be homogenized

Jan 1, 1960

By A. R. Elsea, E. E. Fletcher

Cast X-40 alloy with the lowest nitrogen content studied had a 100-hr rupture stress at 1500°F about equal to the reported value for the commercial alloy. Increases in nitrogen content progressively decreased the rupture strength, and with about 0.1 to 0.2 pct N a minimum strength was reached, but there was no accompanying change in microstructure. Further increases in nitrogen resulted in the fomzation of progressively increasing amounts of a lamellar, pearlitic-type structure at the grain boundaries, with accompanying increases in rupture strength, and above about 0.25 to 0.33 pct N, the rupture strength exceeded the normally reported values. Two series of melts representing different melting stocks exhibited minimum rupture strengths at different nitrogen contents. This suggests that some unidentwed trace element not removed by vacuum melting has a strong influence on the response of this alloy to variations in nitrogen content. In a series of melts with manganese contents ranging from 0.6 to 3.2 pct, the material with the lowest manganese content had the highest 100-hr rupture strength at 1500°F. The manganese variations had no appreciable effect on the microstructure. CAST cobalt-base alloys such as X-40* exhibit high strengths at elevated temperatures (1500°F and above), but they also show considerable scatter in high-temperature properties. Since the design of parts for critical applications must be based on the minimum expected properties, this broad scatter appreciably lowers the design strength of the alloy. If the relatively poor properties exhibited by a few test parts from any given group could be improved, the spread in properties would be narrowed, and the design stress could more closely approach the average expected properties. The purpose of this research investigation was to learn what were the causes of these erratic properties and, if possible, to find methods for eliminating them. Earlier unpublished work showed that vacuum melting markedly influenced the high-temperature strength of cast X-40 alloy. There were indications that this behavior may have been the result of changes in the nitrogen or manganese content of the castings. Consequently, in the current investigation, the influence of variations in nitrogen and manganese content on the structure and high-temperature properties of cast X-40 alloy was studied. In this program, X-40 melting stock was vacuum melted to produce a base material that was very low in nitrogen content and in volatile trace elements. Additions were then made to this base material to produce alloys of the desired composition. The metal was cast into investment molds producing coupons which were machined into stress-rupture bars. These bars were subjected to stress-rupture tests and me-tallographic study to determine the influence of changes in analyses (nitrogen and manganese content) on the structure and properties. Material—The melting stock used for these experi-ments was in the form of shot from two master heats of commercial X-40 alloy. Only one master heat was used in a given series of melts. Thus, any differences in structure or properties that showed up in the specimens from a given series would be the result only of the intended variations in composition. The certified analyses of the master heats were as follows: C Mn Si Cr Ni Lot No. 2 0.50 0.71 0.66 25.44 10.53 Lot No. 3 0.54 0.73 0.70 25.95 10.00 W Fe Co P S Lot No. 2 7.45 1.34 Bal. 0.011 0.013 Lot No. 3 7.58 1.53 Bal. 0.005 0.016

Jan 1, 1960

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by Pfann,&apos; in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann&apos;s process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (=10-6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by pfann,&apos; in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann&apos;s process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (-=,6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By R. W. Fenn, H. A. Lepper, W. R. Hibbard

THIS paper reports the results of static tension and torsion tests made on single crystals of alpha brass for the purpose of determining its elastic coefficients. 70-30 alpha brass was chosen because it has been used extensively in the study of the plastic deformation and because it has the following desirable characteristics: (1) face-centered cubic structure, (2) marked elastic anistropy, (3) low elastic modulus. In 1928 Masima and Sachs&apos; using static methods reported the following values for the elastic coefficients of 72-28 pct alpha brass: S11 = 19.4 X 10-13&apos; cm2 per dyne S12 = —8.35 X 10"&apos; cm2 per dyne S44 = 13.9 X 10-13= cm2 per dyne These values were obtained from the measurements shown in fig. 1. The experimental points for both tension and torsion lie consistently below the lines drawn to represent them. Fig. 2 shows the stress-strain curves for their specimens. Only a few points in the elastic range of these curves were available to obtain their values for Young&apos;s modulus. Therefore, it was considered that a re-evaluation of these data was desirable. In addition a variation of from 1.13 to 1.485 kg per mm2 was found in the values of the critical resolved shear stress for 70-30 alpha brass reported by Burghoff,² Treuting and Brick: Martin,4 Maddin, Mathewson and Hibbard5,6 and von Goler and Sachs.&apos; Therefore, it was desired to evaluate the conclusion of Boas and Schmid8 that a constant resolved shear stress and not a constant elastic shear initiates plastic deformation. Theoretical Considerations*: The elastic deformation of cubic crystals may be defined by three elastic coefficients (S11, S12, S44,) or three elastic parameters (C,,, C,, C,,). These coefficients or parameters are sufficient to define the stress and strain relations for cubic crystals in the generalized form of Hooke&apos;s law referred to Cartesian coordinates. Elastic parameters and coefficients in the cubic system are related by the expressions: C11 —S11+S12/(S11-S12)(S11+2 S12) C12=-S12/(S11-S12)(S11+ 2 S12) (S11 — S12) (S11 + 2 S12) [2] C44 =1/S44 PI It is possible to determine all the elastic coefficients for a cubic metal by measuring two of the three elastic constants: Young&apos;s modulus (E), torsion modulus (G), or compressibility (S). The following relations exist between crystallographic orientation and E, G and S for cylindrical crystals of the cubic system: 1/E = S11 — 2 [(S11 - S12) — Su] (?1² ?2² + ?2²?83 + ?3² ?1²) [4]

Jan 1, 1951

By R. W. Fenn, H. A. Lepper, W. R. Hibbard

A. J. Shaler—I should like to congratulate the authors on the presentation of this paper, which we have been awaiting a long time. The view they have taken of the sintering process, namely that voids are comparable to particles of a second phase capable of dissolving to a slight extent in the metal phase, is an interesting but dangerous one. Pines has given a first-order solution of the problem and Has predicted a decrease in the concentration of pores near the surface. The authors of the present paper have experimentally demonstrated the second-order effects, that is, the diffusion of the space phase between voids of different sizes, and also the movement of atoms from highly curved parts of a void to less curved regions of the same void. I have recently calculated the rate of vapor-phase transport within odd-shaped pores in copper at 850 °C and found that probably at that temperature volume flow is the more rapid shape-changing mechanism. The authors of the present paper have found that at 1000°C, vapor-phase transport is dominant. There is no disagreement here, I think. The dominant phenomenon can easily be different in different temperature ranges and with different pore shapes: I used a cylinder going to a sphere, not a tricuspid going to a "triple cuspidor." But there is some danger in the other art of the explanation, that is, in the study of the diffusion of vacancies from a pore to its neighbors and to the outside. A vacancy is very different in dimension from an atom. When it moves, it carries a field of elastic strain. This has to be taken into account. A concentration gradient of vacancies can cause them to diffuse. But in the absence of such a gradient, they can be made to diffuse by a field of stress. What happens in some of our experiments, and it is most noticeable in the shrinkage of synthetic cylindrical pores, like the tubes we have been working with, may be broken down into the following steps. (1) The presence of a surface establishes a vacancy concentration gradient, as Dr. Kuczynski and the present authors have shown. (2) Vacancies then diffuse in order to decrease this gradient. (3) In so doing, they cause an elastic field to be built up in such a direction as to oppose the diffusion, so that it slows down until it reaches a steady-state rate. (4) The steady-state flow is due to the fact that the surface tension acting on curved surfaces applies a stress to the system which itself mechanically causes vacancy diffusion. What I have said is that the diffusive types of flow of the authors and of Dr. Kuczynski are transient phenomena which soon stop if the pores are large. We are then left with a mechanical problem only, and our researches have not yet disclosed just what the mechanism of flow is; it may be a slip process, or it may take place by a vacancy diffusion of the type Nabarro has de-

Jan 1, 1951

By John G. Simmons

A tutorial account of the tunnel effect between metal electrodes separated by a thin insulating film is presented. Energy diagrams of metal-insulator -metal sandwiches are briefly discussed, and the isothermal and thermal J-V characteristics for symmetric and asymmetric tunnel junctions are derived from a generalized expression. Experimental data from tunnel junctions are presented, and it is shown how, correlation between theory and experiment permits a determination of some of the oxide properties. Finally, the barrier heights in AT-Al2O3-A1 junctions determined by various inr3estigators are discussed. The object of this paper is to give a tutorial account of the electric-tunnel effect between metal electrodes separated by a thin insulating film and to illustrate its utility in the study of metal-oxide interfaces. This paper will emphasize the theoretical aspects of the electric-tunnel effect: however, a brief account of the more recent experimental work will be presented. A more comprehensive experimental study of the tunnel effect will be presented in the following paper by Drs. Pollack and Morris, see p. 497. We will open with a discussion of the energy diagrams for metal-insulator-metal junctions and what we mean by the electric-tunnel effect. Following this is an account of the theoretical studies of Sommerfeld and Bethe, and Holm, and the recently reported calculations on symmetric and asymmetric junctions using the generalized formula. The theoretical presentation is concluded with calculations on the temperature dependence of the tunnel J-V characteristic. In the experimental section, it is shown how barrier heights and thicknesses are determined by comparing the experimental data with the theory. Finally, the results of various investigators on the determination of the barrier heights in Al-Al2O,-A1 systems are discussed. I) POTENTIAL BARRIERS BETWEEN CLOSELY SPACED ELECTRODES Since it is necessary to supply energy to a metal in order to observe electron emission from its surface, it is evident that the potential energy of an electron within a metal is lower than that of an electron at rest outside the metal. It follows, then, that the electron must undergo a change in potential as it crosses the metal-vacuum interface. In the Sommerfeld1 free-electron theory of metals it is assumed that the free electrons, the electrons responsible for the electrical characteristics of metals, move in a constant potential environment in the metal, and are contained within the metal by a potential barrier at the metal-vacuum interface. It will be evident that the idea of a constant potential environment is a very idealized model, since the potential energy of an electron is influenced by all of the atoms and the other electrons within the metal; however, its use is justified by the many excellent results it gives.2 Fig. l (a) is the energy diagram of the model envisaged by Sommerfeld; the metal is represented by a potential-energy well of depth V,; the vacuum level represents the energy of an electron at rest outside the metal. At 0°K the electrons, which exist in pairs in discrete energy levels, fill up the well to an energy ?, the Fermi level. The distance, Vo - ?, from the Fermi level to the vacuum level is known as the work function of the metal, and represents the minimum energy required to free electrons from the interior of the metal at 0°K.

Jan 1, 1965

By J. E. Coyne, L. E. Tanner, J. E. Boyd

In recent investigations of the isothermal transformations of the retained 0 phase in a titanium alloy having 13 pct V, 11 pct Cr, and 3 to 4 pct Al, there have been indications that the w transition phase is the initial decomposition product at temperatures below about 950°C (510 c).&apos; This metastable phase, found in a number of titanium-base alloys rich in stabilizing elements and known to have an adverse effect on their ductility and toughness, is not easily observed by the usual experimental techniques. Since wis coherent with the /3 matrix,495 distinct interphase boundaries are not revealed metallographically. However, in some cases, an etching effect (i-e., a "mottled" /3 surface) poorly resolved by light microscopy has been found to correspond with the presence of w.6 X-ray diffraction examination has generally been the most suc- cessful means for identifying this phase and crys-tallographic determinations have been made.4&apos;5 Dynamic elastic modulus7 and electrical resistivity measurementse have also aided in the identification of w. In the current study, the electron microscope was utilized to examine microstructures in aged Ti-13V-11Cr-3A1 that were unresolvable by light microscopy techniques. Using negative parlodion replicas (shadowed with chromium at 27 1/2 deg) examination was made of various transformation

Jan 1, 1962

By C. Hirayama

THIS investigation was undertaken to determine some of the factors contributing to the embrittle-ment of glass-coated silver wire on heat treatment. The materials used in this investigation were 22 and 23 AWG silver wires obtained from Handy and Harman as "fine quality, soft temper." A wet analysis of one sample showed 99.8 pct Ag. The 23-gage wire was covered with a double layer (2.5 mils thick) of electrical grade fiber glass (aluminum borosilicate glass containing a relatively high concentration of calcium, and a very small amount of

Jan 1, 1960

By A. S. Appleton, M. B. Bever

The stored and expended energies of an Au-Ag alloy deformed in torsion were investigated as functions of strain, strain rate, and temperature. At room temperature, the stored energy, measured by tin solution calorimetry, increased linearly up to an intermediate strain, above which it was nearly constant; at 78 °K the relation was linear up to fracture. Approximate values of the energy stored at 4 OK indicate a rapid increase below 78 OK. The energy stored by specimens deformed successively at 4o and 78oK changed slowly with increasing second strain from the curve for energy stored at 4 OK (measured after annealing at 78oK) to that for deformation at 78°K. The ratios of the stored to the expended energy at room temperature and 78 oK were unusually large. The additional amount of energy stored at the lower temperature is attributed mainly to an increase in the number and energy of dislocations. The stored energy as a function of strain rate at 4oK (measured after annealing at 78oK) increased to a sharp maximum over a narrow range of strain rates, whereas the expended energy changed only slightly. These effects are explained by the generation of point defects resulting from the enforced nonconservative movement of jogs in fast moving screw dislocations. The effect of straining successively at two strain rates at 4oK was also investigated. Stress-strain curves for 4o, 78oK, and room temperature and the results of micro examination of specimens deformed at these temperatures are also reported. THIS investigation is a continuation of a research program primarily concerned with the effects of variables on the energy relations involved in the deformation of metals. The variables investigated in earlier work have included strain, strain rate, temperature of deformation (room temperature and 78oK), and the type of deformation process. Most of this work has been carried out with Au-Ag alloys. In the investigation reported here, the deformation process was torsion, which had not been used previously in the program. The stored and expended energies involved in the deformation process were measured as functions of strain, strain rate and the temperature of deformation in the range 4" to 373" K. The microhardness and microstructure of deformed specimens were also investigated. The relation between stored energy and strain differs for different deformation processes.1,2 In general, the stored energy increases with strain and may attain a nearly constant value at large strains. This value and the rate at which it is reached, however, depend on the process of deformation. This dependence has been attributed, at least in part, to differences in the effective strain rate and rise in temperature of the specimen during deformation. The effects of the temperature of deformation on both the stored energy and the energy expended in the working process have been the subject of only a few investigations.3-6 Values of these quantities at low temperatures are of special interest as they yield information on point defects which, for many metals, is not obtainable at higher temperatures. The effect of the strain rate on the stored and expended energies has received little attention The strain rate has usually been measured only in relative terms, and hence the interpretation of its effect on the stored energy has been mainly comparative.

Jan 1, 1963

By B. A. Joyce, R. W. Bicknell, R. J. Bennett, P. J. Etter

Epitaxial layers of silicon have been grown on single-crystal quartz and alumina by two types of chemical reaction the hydrogen reduction of trichlorosilane and b) the pyrolysis of silane. These reaction systems are described. The cqsfallography of the two systems, as determined by electron and X-ray diffraction, is discussed, and epitaxial mechanisms suggested. The electrical behavior is briefly considered, and the design and properties of field-evert devices fabricated in the epilaxial material are also discussed. RECENT work carried out in these laboratories" has shown that it is possible to obtain epitaxial deposits of silicon on single-crystal quartz and alumina. The purpose of this paper is to describe the method of preparation of these layers using both the hydrogen reduction of trichlorosilane and the pyroly-sis of silane, to compare the crystallographic behavior of films on the two substrates, and to present some initial results of the electrical behavior of silicon layers on alumina. The structural study has been carried out using electron and X-ray diffraction and electron microscopy. The electrical assessment has been made in terms of conductivity and mobility determinations by the van der pauw3 technique, and by measurements on metal-oxide-semiconductor assemblies. 1) FILM PREPARATION Both quartz and alumina substrates, approximately 1 sq cm in area and 0.4 mm thick. were prepared from slices cut parallel to within a few degrees of (11.0), (10.0), and (00.1), and polished mechanically down to about 0.3 p diamond grade. Chemical polishing of alumina slices, using phosphoric acid at elevated temperatures, has also been used; epitaxial silicon layers have been grown on these substrates, but the process is not entirely reliable, possibly because the large strain present in the Verneuil-grown alumina crystal affects the chemically prepared surface. The two reaction systems are fairly conventional and are described briefly below. a) Trichlorosilane-Hydrogen System. The apparatus is shown schematically in Fig. 1. The substrate was heated by induction, with a fused-quartz encapsulated graphite hemicylinder as susceptor. The procedure for carrying out a deposition was to heat the substrate to reaction temperature in a stream of

Jan 1, 1965

By R. T. DeHoff

A new approach to the measurement of the size distribution of particulate structures imbedded in opaque bodies is developed. The method is based upon the assumption of a general two-parameter distribution curve, and the estimation of these two parameters from three well-known counting measurements made upon metallogvaphic sections. The total number of particles in the system is also a product of the analysis. Application of the method with the assumption of the logarithmiconorma1 disfribution function is developed in detail. A complete description of the geometry of a particulate structure requires the determination of the size distribution of particles. The problem of estimating the size distribution of particles of a particular phase in a multiphase system, or the grain-size distribution in a homogeneous system, has been approached by many investigators.&apos;-&apos;0 All of the solutions proposed by these investigators share the following characteristics. a) A minimum of several hundred particle sections in the microstructure must be examined, and some characteristic dimension recorded, such as area,3&apos;5 intercept length,6"9 or diameter.1&apos;2&apos;4&apos;10 b) The resulting data must undergo a series of fairly complex calculations to generate the empirical histogram which describes the size distribution in three dimensions. c) In order to manipulate the result, the histogram must be fitted to some assumed mathematical formula, using the attendant statistical procedures. d) With two notable exceptions,8,10 the particles must be spherical. The measurements and calculations involved are in general very tedious and time-consuming, with the logical result that much effort has been expended in the development of equipment which will perform these tasks automatically and semiautomati-cally.9,11-15 considerable success has been achieved in this area, but the equipment is in general expensive, and usually places stringent requirements On the quality of microstructure which can be reliably analyzed. In laboratories which do not possess such equip- ment, the analysis of geometry is usually limited to measuring total properties of the microstructures, such as volume fraction and interfacial area, because the measurements required are much simpler to make. The determination of size distributions rarely is undertaken. The development which is presented in this paper permits the estimation of size distributions of three-dimensional structures from the same simple counting measurements which are required to determine the surface area and volume fraction of the particulate structure, and one other counting measurement. The basic approach that is used is to assume a general mathematical form for the distribution, which is described by two parameters (as the normal distribution is described by assigning values to the mean and the standard deviation), and then estimate these two parameters from the results of the counting measurements. The introduction of a third counting measurement also permits the evaluation of the number of particles per unit volume, Nv.

Jan 1, 1965

By Y. C. Liu, R. H. Richman

Deformation and recrystallization textures of the a solid solutions of Cu-P, Cu-As, and Cu-Sb alloys are examined as a function of composition. It is found that the deformation texture of copper is unckanged up to a composition of 0.43, 0.41, and 0.24 at. pct of phosphorus, arsenic, and antimony, respectzvely, and then the transition to the 70 : 30 brass type of deformation texture proceeds linearly as the logarithm of the solute content. Recrystallization textures consist of strong, new components that do not all bear the usual<111> rotational relation to the deformation components. The dependence of the deformation texture transitions and the recrystallization orientations upon composition and solute-element type is discussed. A systematic evolution of individual recrystallization components in the annealing texture of copper was portrayed as a function of germanium or tin content in a previous study.&apos; Similar patterns of tex-tural change have been observed with copper-zinc alloys,2 and in less detailed studies of other systems.3,4 In fact, most of the literature dealing with preferred orientations in copper alloys indicates that the influence of solute elements upon textures in copper is of one general type. As the alloy content of copper is increased, the deformation texture changes from the copper type to the 70:30 brass type, and the annealing texture undergoes a comparable change from the (001) [ loo] orientation of unalloyed copper to the {113} <211> type of 70:30 brass, with the notable exception of copper alloyed with Periodic Subgroup V-B elements.4-8 In almost every case it is possible to describe the reorientations after annealing as 30 to 40 deg rotations about <1ll> poles of the deformation components. Since there is apparently not much difference in the final textures of the copper binary systems already investigated, only a limited variety of preferred orientations has served as the basis for current theories of the origin of annealing textures. In order to test the validity of the proposed theories, and the possibility that the <111> rotations are not unique, it would be most desirable to study the reorientation relationships of additional, and heretofore unanalyzed, recrystallization components if such components exist. Examination of the literature reveals a good deal of uncertainty concerning preferred orientations in copper alloyed with elements in Subgroup V-B of the Periodic Table. Phosphorus is known to inhibit the cube texture in copper when present in amounts as low as 0.01 wt pct,8 but the recrystallized matrix that occurs instead of the cube orientation was reported as either random or weakly textured, with orientations not observed in Cu-Zn, Cu-Ge, or Cu-Sn alloys.4-9 A Cu-0.75 at. pct As alloy apparently contained, along with the (001)[100] and (113) <211> type of recrystallization components, {110} <112> and (110) <001> components, whereas an almost random distribution of orientations was found in alloys of higher arsenic content.4 A {110} <001> component also appeared in rolledand annealed Cu-Sb alloys, but otherwise the recrystallization textures of Cu-Sb alloys seem to con-

Jan 1, 1962