Search Documents

By W. D. Robertson

SINCE the comprehensive paper of Moore, Beckin-sale, and Mallinson,' little consideration has been given to the mechanism of mercury stress cracking of copper-base alloys, apart from extensive work on metallurgical and fabrication variables employing mercurous nitrate as an evaluation test. However, with the phase diagrams now available and the recent considerations of interfacial tension at grain boundaries, developed by Smith,2 it appears that the elements of a detailed solution to the problem are available. The facts that require explanation are: 1—Pure copper is not embrittled by mercury, with or without an applied or residual stress. 2—Cu-Zn and other copper-base alloys, in excess of some undefined solute concentration, are embrittled provided an external or residual stress is acting; cracking is not observed in the absence of stress. 3—The path of fracture is invariably intergranu-lar. 4—Copper and copper-base alloys do not dissolve readily in mercury at room temperature.' Consideration of the Cu-Hg phase diagram% hows that, at room temperature, solution of copper in mercury is probably limited by the formation on the surface of a microscopically thin layer of inter-metallic compound, CuHg, having a very limited range of solubility which effectively restricts diffusion of copper and mercury. But, above 150°C (the highest peritectic temperature) copper solid solution is in equilibrium with a liquid Hg-Cu solution and, consequently, copper should dissolve freely in a large volume of mercury with the formation of an equilibrium dihedral angle at grain boundaries in contact with the liquid phase. Depending on the magnitude of this angle, mercury will or will not penetrate the solid phase along grain boundaries and spread over grain faces. Thus the measurement of the dihedral angle of grain boundaries in equilibrium with the liquid phase above 150°C should indicate whether copper is intrinsically resistant to embrittlement by mercury. In view of the fact that mercury is appreciably soluble in copper, it may also be anticipated that diffusion of mercury will take place at higher temperatures in the absence of the intermetallic compound and possibly at a more rapid rate along grain boundaries than through the grains, resulting in a Cu-Hg alloy of unknown properties. In the case of brass, the ternary system Cu-Zn-Hg is involved and, from the resistance of brass to general solution in mercury at room temperature, it is probable that a compound of limited solubility range also exists, similar to the binary Cu-Hg sys- tem. Also, compared with copper, a change in the dihedral angle at grain boundaries in contact with mercury may be expected to result from the addition of zinc to copper. The preceding generalizations appear to be confirmed by the following experiments. Experimental Results Oxygen-free copper wire, annealed at 700°C for 3 hr in copper foil, was immersed in mercury at 170°C, with and without an applied stress. After 24 hr immersion, specimens which were spring loaded to a nominal stress of 10,000 psi had not failed, and there was no apparent embrittlement as indicated by a 180" bend around a diameter approximately equal to the diameter of the wire (0.125 in.) : General solution of the surface had taken place, indicated by a change in diameter of the wire, and the resulting structure of the surface is shown in Fig. 1. It is apparent that angles have developed at grain boundaries and examination at a high magnification indicates that the angle is in excess of 120°, completely excluding penetration of mercury. In view of the measurements made by Smith n the

Jan 1, 1952

By E. E. Schumacher

IN a laboratory devoted to the furtherance of the science of communication, the breadth and variety of the problems encountered are challenging to a metallurgist. In my own long association with the Bell Telephone Laboratories, our metallurgical group has dealt with a vast number of alloys, both ferrous and nonferrous, and with many materials in the border range of metallic properties., The objectives of our design engineers embrace every phase of telephony, and the properties they desire in metals are generally unusual, frequently unique, and often conflicting. Commercial alloys have not always been available with properties to meet a special requirement in the telephone plant, and many alloys have had, therefore, to be custom-made. Anyone who has had the opportunity to observe the results of tests of all types on numerous such alloys, both commercially and specially produced, or who has taken part in the development of an alloy of some necessary, but new or unusual combination of properties, could not fail to be impressed by the frequency with which a desired goal has been reached or adequately approached through the presence of decimal quantities of alloying elements. Nor could One fail to be struck by the occasions when, conversely, of a minute amount Of impurity element has rendered an alloy useful. It is no exaggeration to state that the content be- hind the decimal point often spells success or fail-ure, and the critical content is sometimes far to the right of the decimal point as I shall later illustrate. The great effects of small additions have long been recognized and have, in fact, been described by many investigators. The importance of the minute, however, cannot be overemphasized. Therefore, in this discussion, I propose to illustrate for you some of the startling instances, drawn primarily from our own experiences, wherein small, even vanishingly small, proportions of stranger elements in otherwise common aggregates have com-pletely changed the customary pattern of behavior. No one property has a monopoly as to being dis-proportionately affected by minor elements. Nearly all properties are affected, but there is time here to include only a selected few. I have chosen, there-fore, three of general interest: strength, magnetic, and electrical properties. I shall inquire into both the mechanisms and consequences of these disproportionate effects and try to share with you the fascination and challenge of this field. Strength Properties of Lead and Lead Alloys To illustrate the effect of the minute on strength properties I have selected lead and its alloys, with which we have worked extensively for many years. Lead has the advantages of being available in quantity in a state of high purity and of being fairly easy to melt and fabricate without contamination to any extent detectable by the spectrograph. It has the interesting disadvantages of recovery and recrystallization at room temperature. Whether I

Jan 1, 1951

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By H. L. Luo, W. Klement

By rapidly quenching Ag-Pt alloys from the melt, a continuous series of solid solutions has been obtained. At equilibrium''2 these fcc elements form a peritectic system, Fig. 1. Weighed amounts of silver and platinum powder (325 mesh, purity greater than 99.9 pct) were mixed for 24 to 120 hr, pressed into compacts, sintered at 1000°C in a hydrogen atmosphere for at least 16 hr, and then furnace-cooled. Because of the difficulty in achieving homogeneity in alloys containing more than about 40 at. pct Pt, the sintered compacts were induction-melted under hydrogen in alumina crucibles and then cold-rolled into wires. Small amounts ("30 mg) of alloys cut from various sections of the sintered compacts or rolled wires were heated to at least 50' ~ above the liquidus in an alumina insert held within an induction-heated graphite crucible; then the molten alloy was ejected by a blast of helium onto a lightly polished copper strip held on the inner periphery of a rotating wheel. The flakes thus obtained were typically 1 sq mm in area or often slightly larger for the silver-rich alloys. X-ray diffraction patterns were obtained with nickel-filtered copper K radiation in a 114.6-mm-diam Debye-Scherrer camera with rotated specimens. Lattice parameters and associated uncertainties were estimated from extrapolations against the Nelson-Riley function. High-angle lines were always resolved and spacings were computed relative to r(CuKa!,) = 1.540508 The details of these techniques have been discussed previously.s'6 Lattice parameters of the solid solutions are plotted in Fig. 2, together with the data of Schneider and Esch,' Johansson and Linde,' and Novikova and pudnitskii. Each of the present lattice spacings represents two or more independent determinations. The alloys were homogeneous within 2 at. pct of nominal composition as estimated from the uncertainties in the lattice spacings. Many of the mechanisms involved in the achievement of metastable solid solutions by rapidly quenching from the melt have been previously discussed. There is some evidence" that such solid solubility cannot be obtained when the liquid alloys are cooled

Jan 1, 1963

By N. A. Richard, A. E. Austin, R. E. Maringer

AS part of a detailed study of the structure of metallic meteorites, the concentration and distribution of iron and nickel in the various phases of meteor -itic iron have been measured using an electron-probe microanalyzer. The specimen used was cut from a position about 3 in. below the surface of the Grant meteorite, a one-half-ton iron specimen (containing 9.35 pct Ni) found in New Mexico some years ago. A photomicrograph showing the general Widmanstztten structure, somewhat typical of iron meteorites, is shown in Fig. 1. The line across which the analyses were made is indicated by arrows. This area was chosen so as to evaluate the iron-nickel concentration in the three principal phases visible in Fig. 1. These phases, in the language of meteoritics, are kamacite, taenite, and plessite. Kamacite is the a-

Jan 1, 1960

By P. Gordon

An isothermal jacket microcalorimeter, supplemented by metallographic, microhardness, and X-ray measurements has been used to study the isothermal annealing of high purity copper after room temperature tensile deformation. The amount of stored energy released during annealing has been measured as a function of deformation in the range 10.8 to 39.5 pct elongation. The data have shown the major heat effect to be associated with recrystallization and have allowed an analysis of the recrystal-lization kinetics and the calculation of activation energies of recrystallization. WHEN a metal is deformed plastically, some of the energy expended is dissipated as heat during the working process, while the remainder is stored within the metal in the form of lattice distortions and imperfections. During subsequent heating of the metal, the distortions and imperfections can be largely annealed out and the associated stored energy released as heat. It is apparent that measurements of the evolution of stored energy during such annealing may produce important information concerning the nature of the annealing mechanisms and the imperfections involved. Some excellent studies of this type have been made in the past, notably those of Taylor and Quinney,' Suzuki,2 Bever and Ticknor,3 Borelius, Berglund, and Sjöberg,4 and Clarebrough et al.5,6 None of this work, however, employed isothermal techniques, with the exception of the Borelius studies' in which only the early annealing stages were investigated. Since isothermal measurements, as compared with heating or cooling curve, have the merits that 1—they reveal the kinetics of a process more clearly, 2—the results obtained are more easily applied to theory, and 3—most fundamental investigations of annealing using techniques other than calorimetry have been carried out isothermally, it was considered important to apply calorimetry to the study of the isothermal annealing of metals. Accordingly, an isothermal jacket calorimeter of the Borelius type,' supplemented by metallographic, hardness, and X-ray measurements, has been used to study the annealing of high purity copper after room temperature tensile deformation. Experimental The microcalorimeter has been described fully elsewhere." Briefly, the specimen to be studied is placed in a constant temperature environment of virtually infinite heat capacity achieved, as shown in the drawing of Fig. 1, by means of a vapor thermostat. A high thermal resistance is provided between the sample and the environment and a sensitive differential thermopile (see Figs. 2 and 3) arranged with half its junctions in contact with, and thus at the constant temperature of, the environment, and the other half in contact with the sample. A reaction in the sample develops a small difference in temperature, AT, across the thermopile, which is followed by a recorder-galvanometer set-up as a function of time, t, and is converted to reaction heat per unit time, P, by the use of the equation AT P=a?T + b AT dt The constants, a and b, in Eq. 1 are determined by a simple calibration, making use of the Peltier heat developed by a small current run through the junction of a thermocouple located in an axial hole in the specimen (Fig. 2). In its present form, the limit of sensitivity of the calorimeter is a heat flow of 0.003 cal per hr. The copper used was the spectroscopically pure metal supplied by the American Smelting and Refining Co. in the form of 3/8 in. diam continuously cast rod, reported to be 99.999+ pct Cu. A small amount of the copper was available at the start of this work and is referred to hereafter as lot A. A second batch, lot B, was obtained later, most of the results described subsequently being for this lot. As will be seen, there is some indication that lot A was somewhat purer than lot B, but it is not known whether this difference was present in the as-received metal or arose during subsequent handling. The two lots of copper were remelted and cast into two 1½ in. diam ingots in vacuo, using high purity graphite crucibles and molds. The ingots were upset several times to break up the large cast grains, and then rolled and swaged to rods 0.391 in. in diameter, using several intermediate anneals with about 40 pct reduction in area between anneals. The penultimate anneal was 2 hr at 350°C. X-ray examination showed no marked general preferred orientation in the resulting rods. The grain structure typical of the two rods is shown in the micrograph of Fig. 4." It was found to be virtually im- possible to get an unambiguous measure of the absolute grain size in the two annealed rods because of the profusion of annealing twins and the lack of regularity of the grain boundaries. However, counts of the number of boundaries intersected per unit length along a random line on a polished section, making a correction for the proportion of boundaries (about half) estimated to be twin boundaries, gave a figure of about 0.015 mm for the average grain diameter. The grain size of the rod from lot A was about 5 pct smaller than that from lot B. The rods were cut into 1 ft long bars and these deformed in tension at room temperature to various total elongations in the range 10.8 to 39.5 pct. A strain rate of 1 pct per min was used. The deformed bars were then stored in a dry ice chest until such time as samples were to be cut from them. Five bars deformed as indicated in Table I were used for the subsequent tests. In all cases, all the calorimeter.

Jan 1, 1956

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The microhardness of single crystals of tungsten disilicide has been investigated by the Knoop method. The average random room-temperature hardness of the WSi, matrix was 1350 kg per sq mm. Hardness crnisotropy was noted with respect to plane and indenter orientation as determined by single-crq.stal X-rny studies. Annealing at 1600" and 1800°C decreased the average hardness to 1310 and 1230 kg per sq tnm, respectively, and produced a second phase identified by X-ray diffraction and electron-microprobe analysis to be wSio.7. Ball-impact experiwzents produced rosettes at 850°C. Optical and electron microscopy showed evidence of slip and cross slip and twinning produced by microhardness indentations. Prismatic (100), [001] slip was found and cor~elated with hardness data. THE present study was undertaken to investigate the hardness anisotropy of as-grown and annealed single crystals of tungsten disilicide. The existence of the silicide WSiz in the W-Si system has been well-established and its structure thoroughly investigated zachariasen2 found WSi, to have a tetragonal C type of structure, similar to that of MoSi, with lattice parameters a = 3.212A, Kieffer et al. studied the W-Si system and measured the density and microhardness (at a 100-g load) of both polycrystalline WSi, and WSi,.,. The values found were 9.25 g per cu cm and 1090 kg per sq mm for WSi,, and 12.21 per cu cm and 770 kg per sq mm for WSi0.7, respectively. According to Samsonov et a1.5 the microhardness of polycrystalline WSi2 is 1430 kg per sq mm (at a 120-g load). EXPERIMENTAL The WSi, single-crystal boules investigated in this paper were grown by a Verneuil-type process using an electric arc by the Linde Division of the Union Carbide Corp.6 The largest specimens were 8 mm in diameter by 16 mm long. The crystals had an average density of 9.01 g per cu cm with a tungsten • silicon content of 99.9 wt pct. The major impurities were: 87 ppm O, 41 ppm N. 54 pprn C, 500 ppm Zr, 50 ppm Na, and 50 ppm Mn. The crystals were silicon-poor, the average silicon content being 22.20 pct (stoichiometric value is 23.40 pct), and tungsten-rich, the average tungsten content being 77.70 pct (stoichiometric value is 76.60 pct). As-received single crystals were ground and analyzed by powder X-ray diffraction technique using Cu Ka radiation. Laue and layer line rotation patterns were obtained on cleaved sections of WSi, single crystals. Electron-microprobe traverses of representative crystals were done using a Phillips-AMR electron microanalyzer. Carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to the metallographic examination, the specimens were mounted in Lucite and then polished for short times on polishing wheels using 9-, 3-, and 1-p diamond-grade pastes. Finally they were fine-polished with Linde A powder for 24 hr on a Syntron vibratory polisher. The samples were etched with 4H 2 O:1HF:2HNO3, which is a medium fast-acting etchant. The combination 1HF:2HNO3:5 lactic acid is also a satisfactory etchant. Annealing runs for selected specimens were made at 1600" and 1800°C for 3 hr at 1.0 to 3.0 x 10-5 mm Hg. A Brew tantalum resistance furnace with WSi2 powder for setters was used. The WSi2 powder was the same as that used for the crystal growth. Temperatures were measured with a calibrated W, W-26 pct Re thermocouple and a microoptical pyrometer. Powder X-ray diffraction, emission spectrographic, and electron-microprobe analyses were done after the annealing runs. For microhardness measurements a Tukon Microhardness Tester Type FB with a Knoop indenter was used. Although measurements were taken at loads ranging from 25 to 1000 g, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Only indentations of cracking classes 1 and 2 were considered.&apos; DISCUSSION OF RESULTS Powder X-ray diffraction analysis showed the as-received crystals to be single-phase WSi2. Laue and layer line rotation patterns obtained on cleaved sections of WSi2 single crystals proved them to be tetragonal WS 2 2 The results also indicated that the c axis of the crystal was oriented parallel to the boule or growth axis. Electron-microprobe traverses across the matrix of the as-grown crystals showed them to be homogeneous WSi,. Optical and electron microscopy of etched crystals, however, revealed that they contained minute amounts of the "golden" and the "blue" second phases as opposed to the "white" or WSi2 phase. These two second phases were concentrated in inclusion and etch-pit

Jan 1, 1965

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.&apos;-4 Samsonov et al.&apos; reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami&apos;s Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By D. Turnbull, R. E. Cech

THE supercooling behavior of pure liquid metal droplets has been described.&apos; The solidification behavior of small droplets of Cu-Ni alloys as a function of composition is described herein. The Cu-Ni system is of interest for such an investigation because the components are miscible in all proportions in both the liquid and solid state and the phase diagram of the system, Fig. 1, is a type often encountered in metal systems. It was noted by Van Riemsdyk2 and others that the nature of the "blick" of gold droplets during assaying is not perceptibly affected by the content of the platinum group metals that are soluble in both liquid and solid gold. With the exception of these very qualitative observations there appear to have been no prior investigations of the supercooling of alloy droplets. A series of nine alloys varying in composition by 10 pct (nominal weight) steps was made using certified OFHC copper, 99.996 pct purity, obtained from the American Brass Co., and electrolytic nickel pellets, 99.92 pct purity, obtained from the International Nickel Co. The alloys were melted and cast in vacuo in a high frequency induction furnace. Segregation was minimized by chill casting into 1-in. diam steel molds. Each alloy rod was homogenized at a temperature 50°C lower than the solidus for 100 hr in dry hydrogen. Samples for solidification experiments and chemical analysis were machined from the same portion of each rod and at a depth of in. from the rod surface. A Car-boloy tool was used in taking turnings to minimize contamination of sample by the cutting tool. As a check, a number of samples for microscopic observation were chipped from the ingot with a fragment of pyrex glass. The resultant data in all cases agreed, within experimental error, with the data obtained from machined turnings. A number of small particles, 30 to 50 micron diam, of a Cu-Ni alloy were placed in a quartz vial 1/32 in. diam x % in. long. This was inserted into a platinum ribbon heater and mounted in a high temperature microscope stage. The general procedure followed in inserting samples into the stage and measuring the temperature of melting and solidification was the same as described in an earlier paper.&apos; A chromel-alumel thermocouple was used to study alloys of 88.93 pct Cu, 80.62 pct Cu, and 72.27 pct Cu. A platinum-10 pct rhodium thermocouple was used for the remainder of the alloys. Procedure The assembled high temperature microscope stage was first evacuated and the sample given a 2 min in situ treatment at 900 °C in dry hydrogen to remove surface oxides which might otherwise catalyze crystal nucleation. After this treatment the atmosphere was changed to purified helium and melting and solidification were observed microscopically. It was not possible to determine the solidus with certainty. However, the liquidus temperature was measured very accurately since the surface of the particle changed in appearance from coarse and uneven to smooth, mirror-like within a few degrees. The visually determined liquidus temperature was checked by finding the highest temperature to which the particle could be heated such that it did not supercool upon lowering the temperature. This temperature which checked within experimental error with that found by observing surface change was assumed to be characteristic of the thermody-namic liquidus. In order to minimize the effect of selective evaporation of copper from the alloy, samples were changed frequently and the droplets were heated no more than 50 °C in excess of the liquidus temperature T,. When the latter conditions were fulfilled, T, values were reproducible. After melting, the temperature was decreased slowly until the particles solidified. The sudden release of heat of fusion on solidification caused the

Jan 1, 1952

By E. C. W. Perryman

On electropolishing, high-purity Cu-Sn and Cu-Sn-P alloys with more than 5 to 9 pct Sn were found to contain many grain boundaries with a ridge-and-furrow profile. The effect was not eliminated by solution treatment and was present at the new boundaries in recrystallized material. It could be produced by diffusing tin into the 3 pct Sn alloy and it is concluded that the effect is due to enrichment of certain boundaries in tin, or possibly in an impurity present in the tin, in solid solution. IN the hot working of tin bronzes, especially those with moderately high tin contents, considerable difficulty is frequently encountered from intercrystal-line weakness, which results in cracking at the edges in sheet on strip rolling and in the unsupported regions of the rod in rod rolling.&apos; These difficulties are not at all pronounced with up to 3 pct Sn, but at 5 pct Sn impose serious limitations and at higher tin contents, especially if the phosphorus content is also high, they may become very severe. In some work carried out at the laboratories of The British Non-Ferrous Metals Research Association it was found that a notable lack of ductility in tension at elevated temperatures, associated with intercrystal-line failure, was characteristic of tin bronzes even of relatively high purity. That the intercrystalline fracture is not due to a brittle or molten impurity phase at the grain boundaries was shown by the fact that the temperature at which intercrystalline fracture first occurred decreased with decrease of rate of straining. Tensile tests on some commercial tin bronzes, reported by Goetzel,² show a similar fall in ductility with increasing temperature. As no visual evidence had been obtained showing that the grain boundaries of the tin bronzes were different from those in copper, a more detailed microscopical examination was carried out, and the results of this are given in the present report. Several workers"&apos; have observed that electrolytic polishing is a powerful tool for detecting small amounts of a second phase and in particular for detecting high solute concentrations, "equilibrium segregation," at grain boundaries. Since it had been found that the suggested solutions for electropolishing bronze and the standard solutions for brass and copper did not give satisfactory results it was first necessary to find a suitable electropolishing solution.&apos; Experimental Procedure Materials Used: The cast and wrought materials used for this work were the same as those used for the mechanical tests referred to above. They comprised 3, 6, and 9 pct Sn alloys without phosphorus and the same three basic alloys with 0.03 and 0.4 pct P. A 5 pct Sn alloy without phosphorus, of similar purity, was also examined. The basis materials were Chempur tin, high purity 15 pct phosphor-copper and cathode copper, and spectrographic analyses are given in Table I. Treatment: The cathode copper was first melted under charcoal, degassed by plunging marble chips beneath the surface, and cast through a coal gas flame into sand molds to produce a number of small ingots which after machining were of a suitable size for subsequent vacuum melting. Chill cast bars of the alloys, approximately 1¼ in. in diameter, were then made by melting and casting in vacuo, the tern-

Jan 1, 1954

By J. M. Roberts, N. Brown

The stress-strain behavior of zinc single crystals was measured over a strain range of 10-6 to 10-2. The phenomenon of macroyielding was observed in detail and plastic strains were detected at almost zero-stress. Closed hysteresis loops were observed during loading and unloading in the strain region of about 10-5. From the hysteresis a frictional stress on the dislocation of about 6 psi was obtained. A preliminary analysis indicates that impurities are primarily responsible for the friction. Nonelastic Strains as much as 10 -4 were recovered depending on the amount of prior deformation. Part of the recovered strain occurs instantaneously upon unloading and the remainder occurs at zero stress. The time dependence of the recovered strain was measured. THIS investigation is concerned with the details of plastic deformation preceding the ordinary yield point as measured with the usual strain sensitivity of about 10-4. The approach leads to internal friction observations in the hitherto neglected frequency range below 10-1 cycles per sec. It is believed that if the phenomenon of macroscopic yielding is to be understood, then the stress-strain curve in the neighborhood of the macroyield point should be greatly magnified. It may then be possible to determine whether macroscopic yielding is a unique event or whether it is a process which begins gradually at a lower stress. In the case of low-carbon steel a unique event obviously occurs at the macroscopic yield point as indicated by a drop in the load, but copper appears to exhibit a gradual transition from the elastic to the plastic state. In zinc the yield point is rather abrupt although the data indicates that some plastic deformation precedes large scale yielding.&apos; One of the purposes of this investigation is to determine whether there is an abrupt transition from the preyield microstrain region to the region of macroscopic deformation. Such a rapid transition would support the concept that there is a critical stress for yielding. The concept that yielding is a unique event associated with such phenomenon as activating a Frank-Read source, freeing the dislocation from solute atoms, dislocations cutting through dislocations, or dislocations moving freely by one another, has been expounded widely on theoretical grounds. It is hoped that highly sensitive measurements of strain in the neighborhood of the macroscopic yield point will shed some light on the event known as the "Yield Point". EXPERIMENTAL METHOD 1) Specimens—High-purity zinc was cast into spherical graphite moulds in air and grown into spherical single crystals by the Bridgman method under a positive pressure of Argon gas. Spectro-graphic analysis of cleaved sections from four crystals showed a purity of 99.994 pet Zn. The specimens were acid machined with an 1/8 in. gage section in a form similar to those used by Parker and co-workers.2 Bausch type grips were fastened to the specimen by Epon VI adhesive. The specimens were oriented so that only [1120] (0001) slip occurred. Fig. 1 shows two of the specimens in the grips. Prior to each test, the gage section of the specimen was given a concentrated HNO3 chemical polish followed by alcohol rinsing and air blast drying. 2) Test Method- The shear tests were performed on an Instron testing machine and the experimental set-up was made very "hard". Strain could be measured to a sensitivity of 10 -6 by means of a capacitance gage extensometer. The design and calibration of this type of extensometer to measure microstrain, as applied to pure shear and tensile tests of metals, will be the subject of a separate paper—therefore, only a brief account will be presented here. The method essentially consists of attaching a

Jan 1, 1961

By N. M. Parikh, T. J. Koppenaal

The strengthening mechanism of fiber-reinforced silver has been investigated as a function of fiber density and fiber material. Stress-strain curves were determined in the range 2 x 10-6 to 2 x 10-3 plastic styain and slip lines were examined. The yield strength at 0.2 pct permanent strain is markedly dependent upon fiber density but the stress necessary to initiate plastic deformation is independent of fiber density. The strengthening mechanism of the fibers is shown to be malogous to grain boundary strengthening in poly crystalline metals. The variation in strengthening with different types of fibers is also noted and discussed. In recent years, considerable progress has been made in the understanding of the mechanical properties of two-phase systems, particularly in the classical dispersed-phase alloys where the separation between the dispersed phases is 0.01-0.1µ. However, little work has been done on fiber-reinforced metals where the dispersed-phase separation is considerably larger than this. Parikh1 investigated the mechanical properties of many fiber-reinforced metals and found that two general relationships are always observed, as follows: 1) A fibrous network incorporated into a second weaker metal strengthens the latter, and the amount of strengthening increases with fiber concentration. 2) At a corrstant fiber concentration, the amount of strengthening in a given matrix can vary considerably, depending upon the type of fiber employed. The object of the present investigation was to examine the fuiidamental factors controlling these two observations. procedure: Fig. 1 shows the initial step in the fabrication of the specimens. The sieve is shaken so that the fibers fall into a mold with the longitudinal axes of most fibers in the X-Z plane. The fibers are then compressed to a predetermined density, thus forming a "felt", and the necessary amount of matrix metal is added to the top of the felt. The mold is heated, in vacuum or hydrogen, to above the melting point of the matrix metal; the molten metal flows into the felt, and the entire assembly is cooled. This produces a "composite" that is essentially free of voids. A number of composites were prepared in this manner using 1/4-in. kinked lengths of mild steel

Jan 1, 1962

By W. F. Hosford

A quantitative explanation is offered for the peculiar curled grain shapes found in the microstructures of drawn wires of bcc metals and compressed aluminum specimens. It is shown that once an [011] fiber texture is developed, the slip system are so oriented that further slip tends to produce plane strain rather than axially symmetric flow of individual grains. With plane -strain flow, however, compatibility of neighboring grains can be maintained only by a bending of grains about one another. PROBABLY the most obvious microstructural feature of heavily worked metals is the distorted shapes of grains. In the course of deformation, the shape change of each grain must be compatible with that of neighboring grains; otherwise holes would be formed at grain boundaries. In analyses of poly-crystalline deformation by Taylor and subsequent workers it was assumed that grain boundary compatability was maintained by each grain undergoing the same shape change as the polycrystalline aggregate in which it is imbedded. According to this assumption, when simple tension or compression is applied to a random polycrystal or to one with a fiber texture, each grain ought to deform with axially symmetric flow. Initially equiaxed grains should become cigar-shaped during wire drawing and pancake-shaped during compression. While microstructural observations of deformed metals are generally in accord with such a picture, certain striking exceptions may be noted. Peck and Thomas5&apos;8 found that grains in heavily drawn tungsten, iron, and niobium (columbium) wires become shaped like ribbons curled about the wire axis, Fig. 1. At a suggestion from the author, they rationalized the development of these micro-structures by considering the orientation of the slip systems in the [011] texture formed by the wire drawing. It is shown in this paper that marked departure from axially symmetric flow of grains is also observed when polycrystalline aluminum is severely compressed. Again the explanation must lie in the orientation of the slip system in the [011] texture, which is formed in fcc metals by compression.&apos; THEORY A simple quantitative argument will be presented to show that the development of these microstructures is a result of flow on the combination of slip systems for which the minimum amount of mechanical work is expended in producing a unit tensile (or compressive) strain. First it must be realized that the macroscopic strains of a crystal resulting from slip are given by: where d dy, and dc, are normal strain increments parallel to the x, y, and z reference axes; are crystallographic shear-strain increments on slip systems

Jan 1, 1964

By E. P. Sadowski, R. J. Raudebaugh

A study of micro structural characteristics of a 30 pct Cr, 42 pct Ni, 26 pct Fe alloy has been correlated with its behavior in creep and rupture tests at 1400°, 1600°, and 1800°F. Nitrogen pickup observed at 1600" and 1800°F was associated withfissur-ing of specimens prior to fracture. IN studying the high-temperature characteristics of a nominally 30 pct Cr, 42 pct Ni, 26 pct Fe alloy certain anomalies were observed, namely: The alloy had greater stress rupture and creep strength at 1800" than at 1600° F for time periods beyond 550 hr. As placed in test, this alloy was nonmagnetic. After test, some specimens were found to be fairly magnetic. The gain observed in magnetic response was not solely a function of time and temperature of testing. This is a report of the observations and a recounting of the results of studies made in an attempt to explain the behavior of the material under investigation. MATERIAL AND PROCEDURE All test material was taken from a production size heat of an experimental alloy melted and processed using commercial practice and having the following percentage composition: C Fe Cr Ni Ti 0.05 25.83 30.13 41.59 0.41 Al Mn Si S Cu 0.42 0.75 0.45 0.011 0.34 The material was tested in two conditions, namely mill-annealed and grain-coarsened. Mill annealing, which consisted of heating to about 1900° F in a continuous furnace for about 30 min and air cooling, gave a grain size of ASTM 8 and finer. To produce the grain-coarsened condition, mill-annealed material was soaked for 2 hr at 2050°F in a laboratory furnace and air cooled. This resulted in an ASTM grain size of 4 to 5. Rupture tests were carried out at 1400, 1600, and 1800° F in accordance with ASTM procedures. In tests where only rupture life and elongation at fracture were determined, specimens of 0.252 in. diam and 1 in. gage length were used. In tests where creep curves were obtained, specimens were of 0.375 in. diam and 4 in. gage length. Several of the tests under relatively low stress were discontinued short of rupture. Three low-stress tests are still in progress at this writing. Structural changes which occurred during testing were determined from examination of the tested specimens by light microscopy and X-ray diffraction. Diffraction pattern recordings were made with a diffractometer using copper radiation on samples heavily etched in a picric-hydrochloric

Jan 1, 1960

By L. V. Gregor, C. F. Aliotta, P. Balk

The structure of silicon surfaces, thermally oxi&zed in dry oxygen and in steam, was studied using the electron microscope. It was found that the structure on the original (etched) surface is retained at the outer surface of the oxide, whereas the oxide-silicon interface is smoothed out considerably. This supports the idea that, both in oxygen and in steam, the oxidation reaction occurs at the oxide-silicon interface. Mechanical damage of the original silicon surface affects the rate of oxidation. It also changes the chemical properties of the oxide, as shown by the enhanced rate of etching in buffered HF at the locations of damage. However, the oxide at the originally damaged surfaces still exhibits a high electrical breakdown strength. Exposure of thermal oxides to P205 or BzOs vapor, which will yieldphospho- or borosilicate layers, results in complete annihilation of all fine structure on the surface. Reaction of silicon with C02 gives a surface film which probably does not consist of pure SiO,. THERMAL oxidation of silicon yields uniform and strongly adhering oxide films which are normally amorphous and continuous. Contamination and surface imperfections have been reported to cause local crystallization and the formation of pinholes."&apos; The parabolic-rate law of film growth observed by several workers for the oxidation both in steam and in dry oxygen at higher temperatures suggests that diffusion of one or more reactants through the oxide is the rate-deter mining step. One of the dif-fusants is an oxygen species and oxide is continuously formed at the oxide-silicon interface. This was concluded for high-pressure steam oxidation by Ligenza and spitzer5 from an infrared-absorption study of the isotopic exchange of oxygen. Jorgensen arrived at the same conclusion for the oxidation in dry oxygen by measuring during oxidation the resistance change between silicon and a porous platinum marker electrode in the oxide. Recently, Pliskin and Gnall&apos; reported similar conclusions concerning the growth mechanism from controlled etch studies using a phosphosilicate marker. The work communicated in the present paper was aimed at studying oxide growth on locally damaged silicon substrates and relating it to the chemical behavior and electrical breakdown properties of the films. Since etched and oxidized silicon surfaces normally appear to be very smooth when examined by optical microscopy except for some occasional pits, it was decided to use the electron microscope as a tool. In this way, the detection of surface roughness and damage on a scale comparable to or smaller than the thickness of the film is possible. Also, the microstructure of the original substrate surface constitutes a built-in marker which represents a minimum of perturbation to the growing oxide layer, and no foreign material is introduced. Thus information on surface reactions and additional evidence on the location of oxide formation in steam and in oxygen could be obtained. EXPERIMENTAL Electron micrographs7 were obtained using a Philips EM100 electron microscope. Collodion surface replication was used since this is a nondestructive technique and thus permits replicating the same surface at different stages of processing. In order to establish the effect of different treatments it was found essential to make successive observations of the same area by using a reference point. Reference points were conveniently provided by scribing a small v mark on the original surface with a silicon carbide tip. This procedure yields damaged and damage-free areas near the reference point. Upon replication, the samples were thoroughly cleaned before subjecting them to the next process step. Mechanically lapped silicon wafers (Dow-Corning, 100 ohm-cm p-type, cut perpendicular to the (111) direction) were chemically polished in a rotating beaker with a mixture of 1 part HF (48 pct), 2 parts glacial acetic acid, and 3 parts HNO3 (70 pct) by volume. This procedure yields a smooth surface with a faint "orange peel&apos;&apos; structure due to a "ripple" less than 20002i deep. Oxidation in steam or oxygen was carried out in an Electroglas tube furnace. Steam oxidations were always preceded and followed by a brief exposure to oxygen at the same temperattre. The thicknesses of the oxide films under 3000A were determined with a Rudolph Model 436-2003 ellipsometer,&apos; whereas those over 3000A were measured using the VAMFO technique. In the present study, a solution of 300 g of N&F in 25 ml HF (48 pct) and 450 ml water was used to detect areas of increased chemical reactivity in the

Jan 1, 1965

By J. R. Mihalisin, J. S. Iwanski

The response of Inconel "700" to heat treatment has been studied by light and electron microscopy combined with X-ray and electron diffraction techniques. A heat treatment which vesults in low ductility for this alloy appears to be associated with the formation of MC carbide in a Widmanstdtten distribution. This type of precipitation can be suppressed by suitable heat treatment with concurrent increase in ductility. Various other phases precipitated in this alloy are also identified. RECENT studies of commercial nickel base su peralloys have demonstrated the importance of the morphology of carbide phases upon physical properties.&apos; For example, empirical heat treatment studies applied to Nimonic "80" and Inconel "X" have resulted in prescribing double aging treatments for optimum physical properties. These treatments have subsequently been related micro-structurally to grain boundary carbide morphology.2 The purpose of this study was to obtain information about the morphology and identity of some of the phases precipitated in Inconel "700" after heat treatment. It was hoped that some correlation could be made of micro structure with heat treatment similar to that observed with Inconel "X" and Nimonic "80." EXPERIMENTAL PROCEDURE Specimens were obtained from a hot-rolled bar of Inconel "700" of the following composition: C Mn Fe S Si 0.10 0707 0.42 0.007 0.12 Cu Cr -A1 -Ti- Co Mo Ni 0.02 -14.90 TM 2.22 27.61 2.92-- Bal. Specimens were prepared in the following heat-treated conditions: (A) 2275°F for 2 hr WQ (B) 2275°F for 2 hr WQ + 2000°F for 1 hr (C) 2275°F for 2 hr WQ + 1600°F for 48 hr. (D) 2275°F for 2 hr WQ + 2000°F for 1 hr + 1600°F for 48 hr. Empirical stress-rupture studies had shown that treatment (D) resulted in optimum stress-rupture life and ductility. Treatment (C), although giving a good aging response, resulted in low ductility. Treatments (A) and (B), respresenting individual. steps in treatments (C) and (D) were added here for microstructural comparison studies. The procedure was to make an optical and electron microscopic investigation supplemented by X-ray diffraction analysis of electrolytically extracted residues. Electron diffraction studies were made utilizing selected area diffraction techniques with extraction

Jan 1, 1960

By R. I. Jaffee, F. C. Holden, H. R. Ogden

ECENT papers dealing with the properties of unalloyed iodide titanium have been directed primarily at the determination of base-line properties for alloy investigations. Early work was limited to a few tests because of the limited availability of iodide titanium at the time. In the results of papers by Campbell et al.,1 Gonser and Litton,2 Jaffee and Campbell,3 inlay and Snyder,4 and Jaffee, Ogden, and Maykuth, data on mechanical properties are presented for unalloyed iodide titanium in the annealed and cold-worked conditions. Data are presented in this paper which show the effects of heat treatment on the structure and mechanical properties of commercially produced iodide titanium. Correlation is made between microstruc-tural variables and the mechanical properties. Experimental Procedures Melting Stock: The melting stock used was as-deposited iodide titanium, produced by New Jersey Zinc Co. The furnished analysis showed the following range of impurities: N, 0.004 to 0.008 pct; Mn, 0.005 to 0.013; Fe, 0.0035 to 0.025; Al, 0.013 to 0.015; Mo, 0.0015; Pb, 0.0045 to 0.0065; Cu, 0.0015 to 0.002; Sn, 0.001 to 0.01; Mg, 0.0015 to 0.002; and Ni, 0.003. Hydrogen content as determined by vacuum-fusion analysis was 0.0091 wt pct (0.44 atomic pct) after arc melting and fabrication. Nitrogen analysis on the arc-melted and fabricated titanium showed a content of less than 0.002 pct N. The average hardness of the furnished stock was Rf 70, or approximately 85 VHN. Melting Procedure: The as-deposited rods were rolled, sheared, and degreased in preparation for arc melting. The charge was arc-melted with a tungsten electrode in a water-cooled copper crucible under a positive pressure of high purity (99.96 pct) argon. The final ingot was approximately 2 in. in diameter and showed no increase in hardness over that of the initial stock. Fabrication: Heating for fabrication was done in air. It was begun by forging the ingot into a 3/4 in. diam rod, at an initial temperature of 1600°F. Scale was removed by sandblasting. The rod was then swaged to 1/4 in. diam at room temperature through a series of 20 dies, with approximately 10 pct reduction in area between each die. An anneal of 1 hr at 850 °C in air was given after the 1/2 in. die, such that the final cold reduction was 75 pct. Sections cut from this rod were used for test and microstructure specimens. Heat Treatment: Heat treatments were carried out in resistance tube furnaces with stainless-steel linings, under an atmosphere of gettered argon. As further protection against contamination, the specimens were packed in titanium turnings in a titanium sleeve. Control experiments have shown negligible hardness increases with this method, indicating that contamination from oxygen and nitrogen is slight. Three cooling rates were employed in this work; these have been designated as water quenching, argon cooling (to simulate air cooling under a controlled atmosphere), and furnace cooling. The cooling rate for an argon cool is 100°C per min for the first minute, with an average cooling rate of 35°C per min over a 15-min period. A furnace cool requires about 10 hr, with an average cooling rate of 3.6oC per min during the first hour, and an average cooling rate of 1.2°C per min over the 10-hr period. Microimpact Test: The specimen adopted was based on the cylindrical Izod Type Y specimen (ASTM, E23-41T). All dimensions were reduced to half scale, including the notch radius. Specifications are shown in Fig. 1. The specimen is held vertically in an adapter and broken as a cantilever beam. Impact tests were run on a constant-velocity (11.34 ft per sec) Tinius Olsen impact testing machine with a total available energy of 100 in.-lb. Tests were made to determine the correlation between this microimpact and the standard V-notch Charpy impact test. Curves showing impact energy as a function of temperature for both impact tests are plotted in Fig. 2. Transition temperatures, when they occur, are about the same for both impact tests. All three titanium-rich materials have the same conversion factor, 10. Tensile Testing: Tensile tests were conducted on Baldwin-Southwark testing machines using the 600, 2400, or 3000 1b range. Specifications for the test specimen were taken from the 1948 edition of the ASM Metals Handbook, and are shown in Fig. 1. Strain measurements were made using an SR-4 resistance gage (Type A-7) cemented to the reduced section in conjunction with a lever-type extenso-meter. Readings on the SR-4 strain indicator were

Jan 1, 1954

By R. Wachtell

IN order to study better the phenomena at work in various phases of diffusion of the Fe/Si system when compounded and alloyed by powder metallurgy methods, several attacks have been planned. Electrical, hardness and other measurements have been discussed e1sewhere.l,2 The metallographic phenomena will be considered here. Concerning the metallography of the ferrosilicon alloys, some initial discussion is in order. As this laboratory discovered to its chagrin, there are many traps that lie in wait for even the experienced metal-lographer when he deals with alloys of high silicon content. Chief of these is probably the anomalous behavior of these materials under conventional etching techniques. We have before us, for instance, Corson&apos;s paper" of 1928, wherein is mentioned and illustrated (probably for the first time) the peculiar "barley shell" structure sometimes found in these alloys. Again in 19412 he same author reports the structure in 5-14 pct silicon irons. Houghton and Becker mention its presence&apos; but make only tentative effort to explain it. In 1943, Hurst and Riley6 discussed the "barley shell" and declared it to be a false structure, resulting from the peculiar and characteristic film-forming propensities of the alloy. At about the same time, Wrazej7 proved correct the contentions of Hurst and Riley, establishing pretty well the mechanisms of formation and identifying the constituents involved. Hurst and Riley6 a1so describe in their paper (1943) a "cracked film" structure, also a pseudo-morph, the precise nature of which they do not suggest. Careful examination of such a film reveals that it not only cracks but begins to curl away from the surface of the metal and peel, much in the manner of flaking paint. The careful microscopist will be able to focus on the topmost edge of the flake, and, by optical sectioning, follow it down to the metal surface. We have been able, by oblique illumination of such specimens, to observe the raised segment of the film, the shadow that it casts, and the mating segment on the metal into which it fits. As late as 1946, Hurst and Riley8 found occasion to correct misinterpretation of this "cracked film" structure in a work by others on a 12 pct Si/Fe alloy. The "barley shell" and "cracked film" pseudo-morphs are not the only ones encountered in studies of these materials. A third pseudomorph, which may, however, have some structural significance is a fine striation of the surface. Closely spaced and parallel striae extend entirely across single grains. Each grain shows a different direction for the striae, and different closeness of the spacing. The regularity of this structure, and the fact that the striae do not cross from one grain to another, suggest that the structure is a film cracking controlled in some way by the crystal plane orientation of the surface being etched. In general it is wise for the metallographer dealing with these alloys to cultivate a feeling of uncertainty not only of the more complex questions of interpretation, but also of the basic question of whether that which he sees is indeed a true representation of the structure. We have taken, as a first test of the validity of a structure, its reproducibility "in situ" after repolishing and re-etching of the samples. Thus we knew the "barley shell" to be false (fig. 1) even before encountering the definitive works on the subject. The Metallography of Silicon Diffusion in Laminate Bars: As a first step in the study of the metallography of the diffusion process, we have pressed a series of laminate bars. These bars, or "sandwiches" as we have termed them, were pressed with covering layers of iron powder, and a "filler" of the Fe/Si master alloy under study. Bar dimensions were approximately %, x 3 x 1/4 in. The total

Jan 1, 1951