Search Documents

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The kinetics of crack propagation in a hydrogenated high-strength steel at subzero temperatures indicated that cracking progressed in a discontinuous fashion. The delayed failure process thus involves a series of crack initiations rather than the continuous growth of a single crack. The incubation time required for the initiation of delayed failure was controlled by the diffusion of hydrogen. The activation energy for the process was 9120 cal per g-alom. As the test temperature was lowered the incubation time constituted a greater percentage of the total tinze to fracture, and al -50°F the incubation and fracture times were essentially coincident resulting in instantaneous, catastroplzic fracture. A unique feature of hydrogen embrittlement is the delayed failure process in which the material fails under the action of a sustained load even though it is capable of supporting a higher load for a finite period of time.')' Delayed failure of steel and titanium is characterized by an incubation time, preceding the initiation of a crack in a highly localized region, and the subsequent growth of the crack to ultimate failure.3-5 The kinetics of crack growth in hydro-genated high-strength steels have been studied through the use of resistance measurements and have an important bearing on the mechanism of delayed failure. Delayed failure is believed to be merely a facet of hydrogen embrittlement in which sufficient time is allowed during a test for hydrogen diffusion. The current theories employed to explain hydrogen em-brittlement can be grouped into two types. one6-8 explains the embrittlement on the basis of the pressure exerted by molecular hdrogen in lattice voids or defects while the other9-10 attributes the embrittlement to the influence of hydrogen in the lattice. The mechanism used to explain the nature of the crack kinetics in delayed failure is based on the stress-induced diffusion of hydrogen to the area of maximum triaxiality.3 When the hydrogen concentration in this region reaches a critical value, a crack is nucleated. This initial crack propagates instantaneously until stopped by the higher fracture stress of the adjacent material of lower hydrogen content. The continuation of cracking must then await the further diffusion of hydrogen to the new region of triaxiality near the base of the crack where another initiation will occur. From this mechanism it follows that crack propagation is nothing more or less than a series of initiations with limited fracture. The purpose of this investigation was to examine the kinetics of crack growth in an effort to determine whether or not the process was discontinuous. Studies of crack propagation were conducted at low temperatures to retard the diffusion of hydrogen which is presumed to be the rate controlling process in delayed failure. MATERIALS AND PROCEDURE Specimen Preparation—A commercial heat of air-craft quality SAE-AISI 4340 steel, designated as Heat G, was furnished by the Republic Steel Co. in the form of %-in. hot-rolled bars. The material had the following chemical analysis: Composition of 4340 Steel—G Heat C Mn Si Ni Cr Mo 0,395pct 0.82pct 0.29pct 1.76pct 0.85pct 0.25pct Notched tensile specimens with less than a 0.001 in. radius, Fig. 1, were used throughout the investigation. The specimens were heat treated to a 230,000 psi strength level according to the following sequence: a) Normalize bar stock at 1650°F for 1 hr, b) Stress relieve at 1200°F for 4 hr and furnace cool,

Jan 1, 1960

By L. D. Jaffe, H. C. Mann, E. L. Reed

The authors have recently published1 evidence that brittle transgranular fracture of polycrystalline metals does not originate at a point and propagate continuously across the material, but rather develops at numerous related points, leading to a series of micro-cracks which subsequently link up. Series of related microcracks were observed in steel specimens broken in fatigue—specifically, at the central portions which broke during the final sudden fracture. Microcracks of the type mentioned have also been reported by Baeyertz, Craig and Bumps'2 in steel broken under impact. % Some micrographs published by Irwin3 may possibly be interpreted as showing discontinuous brittle cracks. This paper presents additional observations of the authors on discontinuous crack propagation under various conditions. Impact Test Specimens The impact test specimens were cut longitudinally from a steel forging containing: The heat treatment consisted of oil quenching in a heavy section from 1600°F and tempering at 1260°F. The resulting yield strength was 78,000 psi, tensile strength 100,000 psi, elongation 20.0 pet in 2 in., and reduction of area 55.0 pet. Standard V-notch Charpy specimens were broken in a 217 ft-lb machine at a striking velocity of 16.8 fps. Energy absorption and fracture appearance of this material in the V-notch Charpy test are plotted as functions of temperature in Fig 1. After test, fractured halves of specimens appearing 0, 40, 80, and 100 pet fibrous (to the unaided eye) were electroplated with nickel, sectioned longitudinally (perpendicular to the notch at its midpoint), polished and etched with Cohen-Hurlich-Jacobson (C-H-J) reagent (picric acid plus Zephiran chloride in ethyl ether)4 or with Vilella reagent (1 pet picric plus 5 pct hydrochloric acid in ethyl alcohol).5 Fig 2 and 3 show cracks near the path of final fracture in the specimen rated 0 pct fibrous. Many of the cracks terminate at the boundaries of ferrite grains, some at boundaries of pre- existing austenite gzains. * A crack often starts near the end of another. Cracks within the same ferrite grains are parallel or approximately parallel in several cases. A large percentage of the cracks are branched. Fig 4 illustrated a group of cracks in the 40 pct fibrous specimen. Branching and parallelism are well marked. No more than three directions of crack have been observed on the polished surface in one ferrite grain. This is consistent with the evidence6 that brittle fracture of ferrite takes place on the cube face crystallographic planes: the {100} planes. The appearance of some cracks suggests that they have passed around a projecting corner of a second ferrite grain by going outside the plane of polish. In Fig 5 cracks in the 80 pet fibrous specimen may be observed. Some of

Jan 1, 1950

By I. R. Kramer

In his technical note entitled "Specimen Temperature During Electropolishing of Aluminum Crystals" Dr. Nakada 1 reported that the temperature of his aluminum specimen increased 65°C when it was polished electrolytically; he therefore concluded that the temperature of the specimens used in our work (Nakada's Refs. 4 and 5) similarly increased by this amount. From this he further concluded that the change in plastic-flow characteristics associated with the removal of the surface by electropolishing during deformation were due solely to a temperature effect. We believe that these conclusions are not justified. It is, of course, realized that the amount of the temperature increase is associated with the total heat transfer of the entire system, including the efficiency of the stirring action, heat flow through the grip on the specimen, and so forth. Of great importance is the type of electrolyte used for polishing. For example, in Dr. Nakada's experiment a methanol-perchloric acid solution was used. This solution has a relatively low conductivity and for the current densities of 0.3 amp per sq cm the electrical input appears to be 30 to 40 w. In our research a methanol-nitric acid solution was employed and for the size of specimen employed by Dr. Nakada the power never exceeded 7 w. There are major differences in his test apparatus which also appear to affect the temperature rise. In our case a steel specimen holder was used in order to provide a good heat sink and conduction path. The cathode was a coiled aluminum tube through which a coolant was passed to provide additional cooling capacity near the specimen. The stirrer was placed in a position to obtain maximum cooling efficiency. On the other hand Dr. Nakada used a teflon grip to support the specimen at one end only and a flat copper cathode, thus providing a much less efficient heat sink as compared with the metal grips used in our studies. The relationship between current density and the temperature increase for two sizes of aluminum crystals tested in our tensile apparatus is shown in Fig. 1. The temperature measurements were determined from a thermocouple spot-welded to the surface of the specimen. The thermocouple was protected from the acid by means of a thin film of stop-off lacquer which covered just the outer surface of the thermocouple junction. Whereas Dr. Nakada reported a time delay of 8 min to obtain thermal equilibrium, our temperature change occurred in less than 15 sec. This emphasizes the importance of the heat transfer in the entire system. However, readings were taken over a period in excess of 5 min to assure thermal equilibrium. The data given in Fig. 1 were also confirmed by determining the thermal expansion of the specimen in a sensitive creep apparatus. As may be seen, for the smaller specimen the increase in temperature is 8°C for a current density of 1.5 amp per sq in. The majority of our data on the effects of surface removal on the plastic behavior of aluminum were obtained at current-density values at or below this value. Above 1.5 amp per sq in. the temperature rise is uncertain; for under certain conditions, especially in the vicinity of 2 amp per sq in., the anode can become polarized and the current flow is erratic. This condition is easily recognized because wide fluctuations in the creep and stress-strain data make it virtually impossible to obtain reliable results, a condition which was always avoided in our work. The temperature increase for the larger specimen is less than that of the smaller specimens below a current density of 1.5 amp per sq in. At a current density of 2 amp per sq in. the temperature increased 13°C. The above temperature data are in accord with observations made during creep experiments. Using a transducer capable of detecting strain in the order of 10 -6, temperature changes in excess of 8°C were not detected when the current density was increased to as high a value as 1.5 amp per sq in. Finally we wish to point out that our experimental data cannot be explained solely in terms of a heat effect. For example in Fig. 1 of Ref. 2, the change in slope of Stage II as a function of the rate of re-

Jan 1, 1965

By James C. M. Li, J. Weertman

James C. M. Li (United States Steel Covp.)—The author has discovered a single analytical relation between the minimum, or the steady-state, creep rate and the applied stress confirming a statement made earlier by orn" that such relation should exist and should reduce to the power law at low-stress levels and to the exponential law at high-stress levels. However, as pointed out by the author, all the available theories of creep are not adequate to explain such a single relation. Inspired by such a statement, I have made a suggestion concerning a possible explanation13 of the new relation. This is based on the concept that the rate-controlling step is the cooperative motion of a short dislocation segment. The nature of and the reason for the cooperation have been discussed13 as well as the reason why the motion of the dislocation could be controlled by the mobility of the short segments. A natural short segment has been proposed13 to be the node formed at the intersection of two dislocations. The reason why the node may contain only a few atoms has not been discussed and the application of the proposed model to all the metals and alloys reported in this paper has not been attempted. It seems appropriate to include these in this discussion. The model was partly inspired by the substructure recently observed in the electron microscope on creep specimens. One such example is shown in Fig. 48 in Darken's Campbell Memorial Lecture. The substructure is a collection of dislocation intersections and irregular networks. No pileups have ever been observed in such specimens. A closer look at the network indicates that one set of dislocations is more straight than the other set sug- gesting that the other set may be mobile in the plane of the net. Since, for the network to survive the creep deformation, some dislocation reaction has to take place at the intersection of the two sets of dislocations, the mobile dislocation, even if it can slip in the plane of the net, will have difficulty in moving at these intersections. To illustrate, an idealized network is shown in Fig. 9. The thin lines represent the set of dislocations which are mobile and can slip in the plane of the net except at the nodes which are formed at the intersection of the two sets of dislocations. The other set of dislocations, represented by the thick lines, may have a Burgers vector which is not parallel to the plane of the net, and therefore may be immobile. Because of this nonparallel Burgers vector, the Burgers vector of the node, which is avectorial sum of the Burgers vectors of the two sets of dislocations, will also be nonparallel to the plane of the net. Therefore, the node cannot slip in the plane of the net and the set of mobile dislocations will have to drag the node along as indicated in Fig. 9. Now the problem is how many atoms could be involved in the nodes. Exact calculation of the length of the node is a difficult task especially since the length should be a steady-state length and not an equilibrium length. An estimate of the equilibrium length can be made by balancing the line tension of all the dislocations. The results would be a small fraction of the length 1 between nodes as shown in Fig. 10. In some instances such a calculation shows that the node will not be formed. But, since the calculation is only approximate, it does not rule out the possibility of the formation of a short node. In other instances the equilibrium length of the node is an appreciable fraction of I. Such a node would

Jan 1, 1963

By T. H. Alden

T. H. Alden (General Electric Research Laboratory)—This paper as well as earlier ones of Dr. Wood represent an important contribution to the experimental description of fatigue fracture. The mechanism of fracture proposed by the authors, however, is not established by this data nor supported by other data existing in the literature. Although taper section metallography provides a rather detailed picture of fatigue crack geometry, photographs so obtained must be interpreted with care. The narrow bands revealed by etching, frequently associated with surface notches, are labeled by the authors "fissures". Measurement shows, taking into account the 20 to 1 taper magnification, that the depth of these structures is at most 2 to 3 times the width. This distinction is important in the conception of a mechanism of crack formation. It is difficult, for example, to imagine a deep, narrow fissure arising from a "ratchet slip" model. A surface notch, on the other hand, may form easily by this mechanism. The notches observed in the present work are the subsurface evidence of the surface slip bands or striations in which fatigue cracks are known to originate.4-6 It is clear that an understanding of the structure of these slip bands is of key importance in understanding the mechanism of fracture. The evidence presented shows that these regions etch preferentially, possibly because they contain a high density of lattice defects, or as the authors state equivalently, because they are "abnormally distorted." However, it is not possible to conclude that the distortion consists of a high density of vacant lattice sites. The fact of a high total shear strain in itself does not assure a predominance of point defects as opposed to other defects, for example, dislocations. Other evidence in the literature which suggests unusual densities of point defects formed by fatigue7-' refers not to the striations or fissures, but to the material between fissures (the "matrix"). If a choice must be made, the preferential etching would seem to be evidence for a high dislocation density, since dislocations are known to encourage chemical attack in copper;g no such effect is known for the case of point defects. A third alternative is that the slip bands are actually cracked, but that near its tip the crack is too narrow to be detected by the authors' metal-lographic technique. In this case the rapid etching can be readily understood in terms of the increased chemical activity of surface atoms. Unless a vacancy mechanism is operative, the motion of dislocations to-and-fro on single slip planes will not lead to crack growth. Point defect or dislocation loop generation are the principal non-reversible effects predicted by this model. In any case, the nonuniform roughening of the surface in a slip band6 requires a flexibility of dislocation motion which is not a part of the to-and-fro fine slip idea. The same is probably true of crack growth by a shear mechanism. Either some dislocations must change their slip planes near the end of the band and return on different planes,'0 or dislocations of opposite sign annihilate." The mechanism by which these processes occur in copper at room temperature or below is that of cross slip. Thus cross slip appears to be essential to fatigue crack growth.6'10"12 The fact that a tensile stress opens the slip bands into broad cracks does not indicate the structure of the bands or the mechanism by which cracks form. The charactersitic concentration of slip into bands during fatigue shows a low resistance to shear strain in these regions. (This fact in itself may be inconsistent with a high concentration of vacancies.) The authors contend also that continuing shear produces an additional mechanical weakening so that the bands fracture easily (are pulled apart) under the influence of the superimposed tensile stress. It is equally possible that the only weakness is a weakness in shear, that the crack propagates by a shear mechanism, and that subsequently the tensile stress pulls the crack apart. Even the direct observation of bands opened by a tensile stress would not be conclusive since, as argued above, they may be fine cracks. The same argument applies to internal cracks, their existence in the presence of a tensile stress not indicating the mechanism of formation. Internal cracks originating in regions of heavy shear have also been seen following tensile deformation of OFHC copper,13 so that this mode of fracture is not unique to combined tensile and fatigue straining. The authors point out in their companion report14 that 90 pct of the cracks formed during pure tor-sional strain were within 8 deg of the normal to the specimen axis. If the tensile stress were an important factor in crack propagation, it is surprising that the cracks cluster about the plane in which the normal stress vanishes. Similarly, a study of zinc single crystals showed that for various orientations the life correlated well with the resolved shear stress on the basal plane,'= and was not dependent on the normal stress across this plane. W. A. Wood and H. M. Bendler (Authors' reply) -Dr. Alden's discussion emphasizes the essential point in the relation of slip band structure to

Jan 1, 1963

By R. C. Gifkins, A. Gittins

A. Gittins and R. C. Gifkins (University of Mel-houvne)— Evidence from somewhat similar experiments to those described in this paper has led us to the conclusion that possibility 2) of the four listed on p. 319 is a description of what happens in grain boundary sliding. That is, sliding is limited by accommodation deformation, it being necessary to the Continuance of sliding that this accommodation should take place. An example of such accommodation, though probably not the most important, is fold formation at triple points. The evidence and arguments for this point of view are set out in Refs. 14 to 16. In particular, an experiment with a lead bicrys-tall5 seems to support point 2) rather than 3). In creep of this specimen it was found that at least 90 pct of the extension of a zone 0.3 mm wide at the boundary was supplied by sliding at the boundary. The sliding was localized in a region at the boundary very much smaller than 0.3 mm, in fact, in a region too narrow to resolve optically. In poly crystalline Specimens&apos; there appears to be a surface effect, as found by Rachinger," but it appears that this may not manifest itself at low strains. "Low strains" means <10 pct for a Pb-TI alloy, <2.5 pct for magnesium or "Magnox" A12 alloy, or <40 pct for a 0 brass. Up to this extension the sliding, measured by the mean vertical step at boundaries, is proportional to extension. We are able to say this with some confidence, since the error bars on our points are statistically derived. Our results would lead us to think that the error bars on other work, including that of Mullendore and Grant, are much too large at low strains to show this

Jan 1, 1963

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and "{2,3,10)" or "(127)". (It is now thought1&apos; that the "{0,1,13)" habit reported for the Fe-Ni-C alloys&apos;&apos; is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove.&apos; The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and tj2 = vi (i = 1, 2, 3), the Kz qd 771 elements are given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics cij Iand cij reduce to the unit tensors 6ij and 6ij so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and 77~ are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By G. N. Maniar

G. W. Healy (union Carbide Metals Co.)-The author&apos;s paper is a useful contribution to the store of maps of chemical activities of oxides in multi-component slag systems. It is also a good example of the utility of the Gibbs-Schuhmann technique for calculating activities in a system where that of one of the components has been measured. This paper Koh and Caugherty. This plot is reproduced by alor in X-ray Metallography. Because of this nonlinearity, preparation cf suitable standards and/or correction for absorption and enhancement are essential in microanalysis. However, our objection is not the conclusion that Dr. Aaronson has arrived at nor the technique he has used; but only to the foot-note credited to V. Macres. The level of chromium that he was concerned with (less than 3 pet) is so low that the deviation of uncorrected Cr-curve will be negligible. Besides Dr. Aaronson has used chromium intensity from martensite and set it equal the bulk chromium content of the alloy. Using this chromium-intensity as a reference, he has calculated the amount of chromium in the ferrite. This amounts to the same as using an internal standard. Since the chromium content in austenite and ferrite are almost the same, enhancement due to iron in both will be the same and therefore does not need to be corrected. together with the author&apos;s recently published one1 on the CaO-FeO-Fezo3 system will be most helpful to others learning to apply Schuhmann&apos;s method, which merits a far wider application than it has received to date and should greatly aid our understanding of equilibria between metal and oxide phases. As shown by okcen" its use may even be extended to sections of systems with any number of oxides. I have some questions as to the selection of equilibrium constants made by Dr. Turkdogan. He has chosen one for the formation of Fe2O3 from FeO and oxygen which gives Fea3 activities 50 pct higher

Jan 1, 1963

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and It is now thought1&apos; that the "{0,1,13)" habit reported for the Fe-Ni-C alloys&apos;&apos; is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove. The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics and reduce to the unit tensors and j so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel&apos;s paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel&apos;s attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,&apos;, y uranium, and perhaps zirconim.&apos; The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors&apos; reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato&apos;s value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,&apos;&apos; and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener&apos;s predictions.28 We have no quarrel with Hagel&apos;s placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963

By R. E. Smallman, J. C. Terry

J. C. Terry and R. E. Smallman (Llniuersity of Birmingham, England)—In a recent publication53 Wood and Westbrook have reported the results of an investigation of the tensile behavior of fl-phase AgMg alloys. These results agree in broad outline, but differ in the details, with those obtained in the above laboratory and, consequently, some discussion of their paper would seem appropriate. In our experiments, tests were carried out on extruded wires, 2 mm diam, in a hard-beam tensile machine, and while an oil bath was used for the tests up to 150°C, above this temperature the oil bath gave rise to serious contamination of the specimens and hence tests above 150°C were made in vacuo. This procedure is different to that adopted by Wood and Westbrook. The ß-phase alloys exhibit differences in mechanical behavior when they are tested in different temperature ranges. In agreement with Wood and Westbrook, three characteristic ranges are observed which may be classified as low, intermediate, and high temperatures, respectively. Our experiments show that in the low-temperature region, the shape of the stress-strain curves is similar to that reported. However, in addition, it is observed that the temperature at which the low-temperature region ends is markedly dependent on strain rate, and increase with increasing strain rate as shown in Fig. 18. The temperature at which a transition from the low to the intermediate temperature takes place is about 0.4 to 0.45 of the absolute melting point, Tm. This transition temperature coincides with that at

Jan 1, 1963

By D. K. Deardorff, Haruo Kato

D. K. Deardorff and Haruo Kato (U. S. Bureau of Mines)—We wish to refute the 1875" 20°C value that Giessen, et al., report as the transformation temperature of hafnium. Although these authors state that their work along this line will be reported later, we can&apos;t leave their value undiscussed, for we believe it to be 125°C too high. Our value of 1750° 20°C, which the authors mention, has been substantiated in our laboratories by the use of three other methods. The first method of substantiation was by heating and cooling curves using a hafnium/tungsten thermocouple, the couple having first been calibrated against a t/Pt-10 pct Rh couple. The second method was by quenching and metallography of dilute Hf-Ta alloys. The third cussion, it may be pointed out that the observations of Rogers referred to large unidirectional strains where the internal cracks or voids appeared only after a strain of 32 pct or more. On the contrary the internal fissures observed, as a result of fatigue cycling, occurred for a total extension of some 5 pct and furthermore followed the directions of the slip zones. Finally, it is not our contention, as implied in Dr. Alden&apos;s last paragraph, that the tensile stress is an important factor in crack propagation. Indeed, in connection with the reference to the companion report, special note is made of the fact that "Deformation was apparently concentrated in grains which have a slip plane nearly perpendicular to the specimen axis and thus near the plane of maximum applied shear." This dependence of the growth of fissures on the orientation of the slip planes with respect to the direction of maximum applied shear is clearly shown in work on the torsional cycling of single crystals which has been submitted for publication. method was by heating and cooling curves with W/W-26 pct Re thermocouple. Counting the original resistometric method, four different methods have yielded 1750" 20°C as the transformation temperature of hafnium. All our work on determination of the hafnium transformation temperature has shown that the specimen under test must be quickly heated to and through the transformation temperature if the lowest possible transformation value is to be determined; otherwise a higher value not representative of pure hafnium will result. Speed was emphasized in all methods. In our resistometric work the corresponding voltage, amperage, and temperature readings were taken quickly and the transformation temperature was usually reached within 5 min total heating time. In the thermal analysis work involving Hf/W or W/W-26 pct Re thermocouples the transformation temperature was attained within three minutes total heating time, this time being less because the two variables were

Jan 1, 1963

By R. E. Smallman

R. E. Smallman (University of Birmingham, England)—Recently, Tedmon and Ferriss11 have determined the yield stress parameters oi and ky for tantalum by measuring the lower yield stress as a function of grain size 2d and fitting the results to a relationship of the form They report that although ky , which is taken to be a measure of the dislocation locking strength, is small (- 2 to 4 x 106 cgs units) a substantial yield drop is nevertheless observed in a normal tensile test. Niobium gives a similar result,12-14 as pointed out in the original work by Adams et a1.,12 and in order to check this apparent anomaly the yield-stress parameters of electron beam-melted niobium have recently been reanalyzed15 by the Luders strain technique. In this method the strain hardening part of the stress-strain curve is extrapolated to zero plastic strain; the intercept on the preyield portion of the curve is taken to give oi, whilst the difference between oi and the lower yield stress gives kyd-1/2. The results indicate that ky increases with increasing grain size and hence, a plot of vs d-112 yields an apparent ky, which is lower than the true value. A similar effect could account for the small ky found in the relatively pure tantalum used by Tedmon and Ferriss. The variation of ky with grain size shows that dislocations are more strongly locked in coarse-grained specimens than in fine-grained samples. In niobium, this may be attributed to the fact that the dislocation density in the fine-grained material is higher than that found in the coarse-grained samples which are given a sufficiently prolonged anneal to remove any residual substructure and, since the metal contains only a small amount of interstitual impurity, a variation in locking occurs. By contrast, application of both the grain size analysis and the Luders strain method to yield-stress data from commercially pure vanadium containing a large amount of interstitial impurity gives consistent values of oi and ky, with ky independent of grain size and temperature. Electron microscope observations show minor variations in dislocation density from grain size to grain size, but in any case in this material the dislocations are heavily locked with precipitate. On yielding new dislocations are generated and, as a consequence, the importance of any differences in dislocation density between the various specimens of different grain size is considerably reduced. It is perhaps significant that Adams and lannucci,16 working with a grade of tantalum containing a higher interstitial content than that used by Tedmon and Ferriss, prepared the specimens of different grain size by annealing in the temperature range 1500" to 2000° C to minimize any differences in dislocation structure, and found that ky had a value of 1.04 x 107 cgs units, independent of testing temperature. Such behavior is consistent with the dislocations being locked by carbide precipitates so that the generation of free dislocations is an athermal process. The recent work of Gilbert et al.17 also shows that in tantalum there is no significant variation of ky with grain size provided it contains 150 ppm of oxygen. In this case, however, the dislocations are not locked by precipitate and ky is temperature dependent. C. S. Tedmon and D. P. Ferriss (authors&apos; reply)— We would like to thank Dr. Smallman for his interesting comments and discussion to our paper, "The Dependence of Yield Stress on Grain Size for Tantalum and a 10 pct W-90 pct Ta Alloy".18 It was suggested that perhaps the relatively small values obtained by us for ky of tantalum could be attributed to the same cause that accounts for the apparently small values of ky that result when it is determined by the Luders Strain technique. Since our values were obtained by plotting the lower yield stress vs the reciprocal of the square root of the grain size, it is not clear how this could be the case. The values of ky in this experiment have been calculated, using the Luders strain technique. With this method, values for ky on the order of 2 x 105 to 5 x lo6 cgs units were obtained. In spite of this rather large variation, the magnitudes are still small, and there appeared to be no good correlation between ky and the grain size or the yield stress, probably because of the difficulty in accurately extrapolating the work-hardening portion of the curve back to zero plastic strain. As was shown in the original data,18 there was little work hardening in any of the curves, at any temperature. In his discussion, Dr. Smallman also points out how ky has been observed to increase with increasing grain size, when determined by the Luders strain technique. There are at least two possible explanations for this. In the first case, if it is assumed that the bulk of the interstitial impurities are concentrated at the grain boundaries, then, of course, the available grain boundary area would decrease with increasing grain size, thus presenting less area for the interstitials, which would then presumably increase the concentration within the grains, thereby increasing the locking of the dislocations. In the second case, the increase in ky with increasing grain size would be attributed to the nature of the grain boundary itself. One of the several ways of deriving the Hall-Petch equation19 is based on the stress concentration arising from a pile-up of dislocations at the boundary. The ability of the stress concentration to unlock a source in a neighboring grain would depend on the strength of the grain boundary. As is well-known, the nature and struc-

Jan 1, 1963

By G. W. Powell

G. W. Powell (Ohio State University)—Appleton and Bever measured the quantity Es which, for a solid torsion specimen, is basically an average quantity. Es is the amount of energy stored in a solid torsion specimen strained to a surface shear strain of divided by the total number of gram-atoms of alloy in the specimen. It would seem more meaningful and rigorous to deal instead with the quantity which is the energy stored per gram-atom of an alloy uniformly strained to the shear strain . The purpose of this discussion is to demonstrate that as a function of y is readily obtained from the torsion data. radius of the torsion specimen, shear strain at the surface of the torsion specimen density of the alloy, atomic weight of the alloy, and total energy stored in unit length of the torsion specimen. The energy stored in unit length of an elemental tubular section of the torsion specimen is, as given by Appleton and Bever, where E is expressed as calories per gram-atom. The energy stored in unit length of the torsion specimen is

Jan 1, 1963

By W. C. Leslie

W. C. Leslie (Edgar C. Bain Laboratory for Funda mental Research)—This investigation, with its com bination of high-purity metal, calorimetry, and metallography, will serve as a model for annealing studies for a long time to come. The evidence for a competition between recovery and recrystalliza-tion is particularly convincing. The demonstration of edge-nucleated recrystallization was so clear that it may obscure the necessity for other types of "nucleation" sites; otherwise, single crystals of aluminum could not be recrystallized after cold work. At least three types of sites have been found to operate in iron: 1) high-angle boundaries, probably in the same manner as in aluminum, 2) matrix sites, 3) inclusions or second-phase particles. In each instance, the cells developed during cold work and perfected during recovery are the "nucle for recrystallization. Observations by ourselves and others of the dislocation structure of cold-worked metals and of the structural changes that occur during annealing have led us to doubt the validity of the basic assumption of the Lucke-Detert theory, and of the modification developed by Gordon and Vandermeer, that during recrystallization of a metal containing foreign elements in solid solution a high-angle boundary is ad vancing into a cold-worked matrix having a random distribution of solute atoms. We contend that an es sential part of the cold-working and annealing of solid solution alloys is the trapping of solute atoms by the low-energy "wells" afforded by individual dislocations and by dislocation arrays. If cells are formed during cold work, the cell walls are stabilized by this concentration of solute atoms. Thus, solutes inhibit recrystallization not only by decreas-ing the rate of high-angle boundary migration, but also by preventing the formation of high-angle boundaries by subgrain growth or coalescence, i.e., solutes can inhibit both "nucleation" and growth. In addition to stabilizing the dislocation Structure, the solute-dislocation interactions may produce clusters of solute atoms which are not as readily assimilated into the recrystallized grains as are individual solute atoms. There is an additional complication. The dislocation structure formed upon cold working a dilute solid solution may not be the same as that formed during cold working of the pure solvent metal. The solute can either enhance or minimize the formation of cells during cold working. Both effects have been observed in binary alloys of iron. The annealing process is inextricably connected with the mechanisms of strain hardening and solid solution hardening. Although the correlation between experimental boundary migration rates and the predictions made from the theoretical equations are impressive, it should be mentioned that in at least four other instances (Pb-Ag and pb-Au,15, Fe-Mn,16, Fe-Mo)17 the agreement was rather poor. In brief, while it is probable that the migration of high-angle boundaries is held back by solutes in the manner described, this is only a partial explanation of the total effect of solutes upon recrystallization of cold-worked alloys. Paul Gordon and R. A. Vandermeer (author&apos;s reply)— The authors first wish to thank Dr. Leslie for his compliments of this work. It is perhaps worth pointing out that some of Dr. Leslie&apos;s remarks are directed toward subject matter covered in two earlier papers in our work.18,19 We agree with Dr. Leslie&apos;s main contention that the exact nature of the metal structure in the vicinity of a boundary should have an effect on the boundary migration. The theory of Lucke and Detert does not take such detail into account, nor does it account for orientation effects on the migration rates. We assume that since our data checks the theory so well, the effects of detailed structure are statistically averaged out by the polycrystalline techniques used just as are the effects of orientation factors.

Jan 1, 1963

By E. A. Steigerwald

E. A. Steigerwald (Thompson Ramo Wooldridge, Inc.1— he authors&apos; results clearly indicate that cracking can be produced by the hydrogen pressure developed during a charging operation. This type of cracking or blistering has also been observed in polycrystalline materials24"28 when the charging conditions are sufficiently severe and is often referred to as irreversible embrittlement since it cannot be removed by a baking treatment. There are additional data, however, which must be considered before a pressure theory can be generally employed to account for all failures which occur as a result of hydrogen. In many cases, hydrogen embrittlement in a tensile test or in delayed failures under static loads is a reversible phenomena which cannot be simply explained on the basis of preexisting cracks generated by the charging operation. It is this aspect of the problem which has prompted many investigators to seek mechanisms other than hydrogen pressure to explain their results.24&apos;n728 Fig. 15 indicates an example where, under specific experimental circumstances, hydrogen embrittlement can occur at liquid nitrogen temperatures. In this case, which has been previously decribed,&apos;&apos; specimens were charged with varying quantities of hydrogen, immediately quenched, and tested in liquid nitrogen (-320°F). A companion set of identical specimens were charged, aged at 300°F to remove the hydrogen, and also tested at -320°F. When the current density was greater than lo-&apos; amp per sq in., embrittlekent occurred in both sets of specimens, indicating that cracking had occurred during charging and the embrittlement, as in the case of Fe-Si single crystals, was irreversible. At current densities between approximately 103 and lo-&apos; amp per sq in, the embrittlement was present only for those specimens which contained hydrogen during the testing sequence. The embrittlement was therefore reversible with respect to the aging and charging operations. Since extensive hydrogen movement would not be expected at -320°F, it is difficult to reconcile these data with a mechanism which requires pressure and pressure dependent growth of preexisting cracks. There are other features of hydrogen embrittlement such as the reversibility of the incubation time for delayed failure with respect to applied stressg0 and the influence of prestraining31 which are also difficult to explain using a pressure model. Any general mechanism of hydrogen embrittlement will have to consider the reversible aspects of the embrittlement data as well as the irreversible portion which has been clearly presented for the Fe-Si crystals and which is consistent with a pressure model. A. S. Tetelman and W. D. Robertson (authors&apos; reply)—he authors agree with Dr. Steigerwald that a general mechanism of hydrogen embrittlement must be applicable in all cases where embrittlement occurs. Dr. Steigerwald&apos;s experiments were performed on an iron alloy which has an extremely complex microstructure, and therefore does not lend itself to the direct and detailed observations that can be made in Fe-Si. The change in the characteristics of cracks as a consequence of annealing at 300°F is not really known in detail but it is probable that stress-relaxation (blunting) occurs, dislocations produced near the crack tips will be pinned by carbon atoms, and hydrogen will be lost to the atmosphere. Any, or all of these effects of annealing will alter the ease with which a crack subsequently propagates under applied stress. A quantitative treatment of the problem must take these effects into account. Since diffusional processes are presumably eliminated at -320°F, the general mechanism proposed by Dr. Steigerwald&apos;s colleagues cannot be operative at this temperature. A detailed discussion of the general&apos; inapplicability of this mechanism has been presented elsewhere. However, the data presented by Dr. Steigerwald in his discussion can be explained in terms of a pressure model. Crack propagation under internal pressure P and applied stress occurs when where is the total energy expended in creating new surface area and by plastic work at the crack tip. The total crack length increases with increasing current density, since we have shown that it systematically increases with hydrogen concentration and Dr. Steigerwald has shown that hydrogen concentration increases with current density. For large L (high current density) Eq. [I] can be satisfied even if P = 0 and the embrittlement process does not require the presence of hydrogen. Specimens charged at a lower current density will con-

Jan 1, 1963

By Kenneth A. Moon

Kenneth A. Moon (U.S. Army Materials Research Agency)—The authors are to be congratulated for a very interesting and valuable paper. Their discussion of the structural implications of the results shown in their Fig. 5, however, requires a small correction. The model of Speiser and Spretnak with 0 = 1 and z&apos; = 2 is perfectly reasonable for the Ti-O a phase, but Eq. [3] is valid only for solutions sufficiently dilute that the number of empty sites excluded by more than one filled site is negligible. The composition at which intrinsic saturation occurs therefore cannot be deduced from Eq. [3], but but must be decided by consideration of the structural details of the phase in question. In this case, intrinsic saturation is expected not at the composition Ti3O but at Ti2O, because Ti2O has the anti-Cd structurel4 for which each filled octahedral site has two nearby empty sites, one in the hexagonal plane immediately above it, and one in the similar plane below it. The other two models, with ?=1/3 and 1/2, imply a distinction between octahedral sites in pure titanium which is not easy to justify. The problem of extending Speiser&apos;s and Spretnak&apos;s treatment in a general way to more concentrated solutions will be the subject of a forthcoming publication by the writer. M. T. Hepworth and R. Schuhmann, Jr. (authors&apos; reply)—The authors wish to thank Dr. Moon for calling to their attention the paper by Holmberg which presents the results of X-ray studies of Ti-O solutions ranging from 0 to 33 at. pct 0 and quenched from various annealing temperatures between 400" and 1800°C. Within these ranges, Holmberg found three types of phases: 1) At high oxygen contents (above 25 at. pct) and low annealing temperatures, he found the anti-Cd(OH)2 structure referred to by Dr. Moon. In this structure each titanium atom is in contact with 3 oxygens and each oxygen is in contact with 6 titaniums, the "available" oxygen sites corresponding to every other layer of octahedral sites in the titanium matrix. The limiting composition is Ti2O. However, this anti-Cd(OH)2 structure was not observed for samples containing 25 at. pct 0 or less. 2) For the specimen containing 25 at. pct 0 annealed at 400°C an ordered Ti3O structure was observed. This structure is related to the anti-Cd(OH)2 structure but differs from it by providing only two oxygens adjacent to each titanium atom and thus is consistent with the model represented by Eq. [5] in our paper, with 6 = 1/3, z&apos; = 0. 3) For dilute solutions and for more concentrated solutions annealed at higher temperatures, the structure corresponds to that of the metal with random distribution of oxygens among all the octahedral sites. Thus, it is interesting to observe that the thermo-dynamic indications of ordering in the vicinity of Ti3O can now be supported qualitatively at least by Holmberg&apos;s X-ray evidence of the existence of an ordered phase of the composition Ti3O. That is, for solutions with oxygen contents close to that of Ti3O, both the thermodynamic data and the X-ray data are more consistent with models based on the ordered structure of Ti3O than they are with the model which Dr. Moon suggests corresponding to "intrinsic saturation" at Ti2O.

Jan 1, 1963

E. R. JETTE*—The way this ternary was developed there are two directly determined points on each of the iso-thermals except the 700° isothermal, where I believe there is only one. How were the end points determined, and what was the basis for it? Whose work formed the basis for the silver copper line ? M. B. BEVER †—At most temperatures the authors determined three points of the isothermal line. For example it can be seen from Fig 3 and 4 how three points for the 600°C contour line were obtained. The authors took two additional points for each temperature from the copper-silver binary diagram contained in Hansen&apos;s volume on constitution diagrams. It is correct that the 700°C contour line is based only on one point in the ternary field which was found by a slight extrapolation of Fig 4. R. I. JAFFEE*—Are the tie lines representing phases in equilibrium parallel to the silver-copper boundary ? M. B. BEVER—Are you asking that as a matter of principle ? R. I. JAFFEE—I assumed that would follow from principle. I wonder if that is in accordance with the authors&apos; ideas too. M. B. BEVER—I do not believe the authors obtained any information on the tie lines in the two-phase field. Of course, in the limiting case of very low gold contents the tie-lines approach to the silver-copper boundary, but generally in the two-phase field I do not think that the tie-lines have to be parallel to the boundary. E. R. JETTE—1 am quite sure they do not have to be parallel. You cannot tell from this work in which direction they go. E. A. GULBRANSEN*—Were any pycnometric measurements made to check the lattice parameters of the alloys ? M. B. BEVER—I did not hear any-

Jan 1, 1950

By Hsun Hu

C. G. Dunn (Geneva1 Electvic Reseavclz Labo,vatory)-Dr. Hu16 has obtained a number of rolling and annealing texture results that partly agree with those of Dunn17 and Dunn and Kohl8 for experiments of a similar nature. I would like to discuss some of the points of agreement as well as some of disagreement and then present some unpublished data as a contribution to the work on textures. Firstly, there is agreement on the components produced during a 70 pct cold-rolling reduction of a (110) [001 ] single crystal; there is agreement on the forma- tion of a (110) [001] recrystallization texture provided recrystallization occurs at 800°C or higher; and there is agreement on the formation of (120) [001] components provided recrystallization occurs below 600°C. There is some disagreement on the low-temperature recrystallization since I also obtained a substantial amount of a (110) [001] component while the author obtained only (120) [001] components. I also discussed the differences between low- and high-temperature recrystallization (which included further annealing changes in the samples on long

Jan 1, 1962

By J. D. Meakin

J. D. Meakin (The Franklin Institute Laboratories)— In a recent paper Garofalo12 has shown that a number of experimental creep results can be represented by the empirical relation In this expression ? is the steady creep rate, s is the applied stress, and A is a constant at a given temperature; a and n are adjustable parameters. Garofalo has shown that Expression [6] approximates to a power function at low stresses and a simple exponential function at high stresses. Among the data used by Garofalo are the results we published for creep of copper." For these results we found that the best correlation was an exponential law with different parameters in the low-and high-stress region, respectively. That is, i = A exp qs where A and q have different values above and below a critical stress a,. In Ref. 13 are listed a variety of observations which support the proposal that different mechanisms are operative at stresses above and below a,, and it is not felt appropriate to repeat those observations here. The purpose of this note is to demonstrate that, although the representation used by Garofalo does fit the experimental data very well, this fit cannot be used to conclude that only one mechanism is rate-controlling. The argument is best made graphically and is illustrated in Fig. 9. The continuous curves 2 and 3 represent pairs of simple exponential functions which intersect at i = 10-5. The curve 2 closely resembles the copper results in that a change of slope of 2:1 occurs at i = 10-5; the two functions shown are in fact: e = 10-7 exp (1.150) and ? = 10-6&apos; exp (0.576s) For purposes of comparison, curve 3 represents two exponential functions with a change of exponent of 3:1 and curve 1 has the exponent 1.150 throughout. It is quite clear that a satisfactory straight-line fit is obtained on a Garofalo plot for all three curves. The curves represent processes which have either a single stress exponent or two ex- ponents in a ratio as high as 3:l. It must, therefore, be concluded that the ability to obtain a linear dependence between log i and log (sinh cyo) cannot be taken as evidence for a single activated process. In fact, to some extent the way the experimental points quoted by Garofalo lie about a best fit straight line on the log (sinh as) plot indicates that two processes are indeed occurring. This is seen in Figs. 7(c) and 8(c) of Ref. 12 where it is particularly evident that the experimental points deviate from the straight line in a manner similar to curves 2 and 3 of Fig. 9. It is, of course, recognized that the generally used exponential form is an approximation to the hyperbolic sine function which is not valid for exponents of less than 1.2, e.g., qs < 1.2. The only curve in Ref. 12 which is affected by this restriction is Fig. 6(b) where the deviation from a In ? vs s

Jan 1, 1964