Search Documents

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By Stephenson D. B, Burgess J, Burgess F. L, Marshall S. H

A new high intensity flotation process 'FASTFLOT' is explained and its theoretical advantages compared with other flotation systems are discussed. The results of initial FASTFLOT testing on the zinc roughing circuit at Pasminco Mining, Broken Hill South concentrator are presented and compared to recent plant data. The comparison suggests that on roughing duties, the FASTFLOT process yields superior concentrate grade while requiring less than one third the residence time of a conventional mechanical cell plant. Strategies for FASTFLOT deployment are also presented.

Jan 1, 1994

By S Kowalczuk, S V. L Barrett

The potential for adverse surface settlement during tunnelling in soil and rock poses a significant risk to the successful completion of any tunnelling project. Undesirable ground movement may lead to unacceptable level of damage to surface infrastructure, buildings and the environment, resulting in safety concerns as well as causing significant delays and costs to a project. One of the empirical methods which is commonly used to predict surface settlement in the early stages of a project’s development is the volume loss approach as described by Mair, Taylor and Burland, 1996. This method was developed for use in soft ground; however it has also been applied in weathered and soft rock to provide an initial indication of potential surface settlements along a proposed tunnel alignment. This paper presents some initial thoughts on the use of this method in weathered and soft rock and the associated limitations which need to be taken into consideration when interpreting the results. This includes complex weathering profile cases where the strength and stiffness of the ground does not necessarily increase with depth.CITATION:Kowalczuk, S and Barrett, S V L, 2014. Initial thoughts on application of the volume loss approach for estimates of surface settlement due to tunnelling in weathered rock, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 641–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. High-grade Transvaal chalcopyrite was neutron irradiated in a TRIGA reactor to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes during which time significant anomalies were observed. First, an initial period of rapid dissolution lasting a few minutes; second, an arrest or "plateau" region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effect of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured. The initial rate data were correlated by considering the rapid reaction to be due to the dissolution of surface oxidation products or the formation of an iron depleted surface layer. The data for the second slower reaction have been explained to be due

Jan 1, 1972

By Rashleigh C

The selection and application of an effect- ive firing system first require a clear under- standing of the initiating abilities of the com- ponents in such systems. The conditions under which charges can be prematurely initiated by a detonating cord downline must be appreciated. This is a principal consideration in the design of a successful downline/'Anodet'/primer assembly. The advantages and limitations of an electric and several non-electric initiating systems are explained. The factors which in- fluenced selection of the two most suitable systems for use at Isa Mine (viz. downline/ 'Anodet'/primer assemblies and the reinforced long-lead 'Anodet'-type delay system) are dis- cussed. Blasts are detailed in which each of these has been applied. The initiating design for a hypothetical 2 x 106 tonne blast using electric short delay detonators and multi-channel exploders is presented. In this design, charges in remote blastholes are activated after the detonation of earlier firing charges by protecting the firing lines with sandbags.

Jan 1, 1978

By Duport. P. J.

INTRODUCTION In February 1981, the Canadian Institute for Radiation Safety (CAIRS) initiated a routine Personal Alpha Dosimetry service for personnel of the Canadian uranium mining industry. This service is based on the use of the [Personal Alpha Dosimeter] developed by the French Atomic Energy Commission (CEA). The origins of personal alpha dosimetry and its rational are briefly described. Technical and organizational aspects of a routine personal alpha dosimetry service are outlined in this paper. HISTORICAL BACKGROUND International recommendations (1) and Canadian regulations have established Maximum Permissible Exposures (MPE) for each source of radiation exposure. Uranium workers in mines and mills are exposed to external radiation ( [y] rays) and to internal radiations ( [B] and [a] particles) which are delivered to the respiratory track by airborne alpha emitters (Rn and Th daughters and Long Lived Dust). To date, dosimetry for uranium workers has been performed by area monitoring/collective dosimetry. In North America the concentration of radon daughters is routinely measured by grab samples taken at the work place and by on-site gross alpha counting. The concentration of potential alpha energy is then calculated (usually by Kusnetz method) and expressed in Working Levels (WL). The time spent by each worker at a given work place is determined from his time sheets and used to calculate the individual monthly exposures to airborne alpha emitters, which is then expressed in Working Level Months (WLM). The uncertainties attached to such a procedure are obvious even in the case of frequent grab samplings and can be expected to lead to an underestimation of individual doses. Among fifteen possible sources identified in a mine situation, (2) four may stretch the standard deviation of the measurements' distribution, nine may lead to an underestimation and two may lead to either an underestimation or to an overestimation. To improve this situation, in 1971 the Atomic Energy Commission began studying the use of personal alpha dosimeters to determine individual exposures from the airborne alpha emitters encountered in the uranium industry environments. Criteria for a Personal Alpha Dosimeter In order to minimize the difficulties encountered in determining exposures received by uranium workers, the CEA in co-operation with the Atomic Energy Control Board of Canada (AECB), has developed a set of criteria for personal alpha dosimeters. Exposures may be determined easily and accurately using this criteria. Autonomy The dosimeter must operate for at least 10 to 12 hours. Excess time spent in the mine or in the facility may possibly be related to an accidental situation causing unusual levels of radioactivity. Since the dosimeter may be needed in non-underground settings where a cap lamp is not used, full autonomy is desirable. Maintenance, Periodicity of Reading In order to complement other dosimetry systems, the personal alpha dosimeter should be read monthly when the filter should also be changed. Routine air flow checks can be made according to local conditions (e.g. diesel loading). Radioisotopes Identification Since the exposure unit (WLM) is based on the concentration of potential alpha energy in the air, the personal alpha dosimeter should be capable of identifying each short lived alpha emitter included in the calculation of the WI, and WLM. Permanent Exposure Record Three points may be considered here: 1. In many countries, lung cancer in uranium workers is a compensable occupational disease. In some instances, compensation is awarded when it can be proven that the worker has received an exposure above a certain limit. The present uncertainty of the individual exposure makes the compensation procedure difficult. 2. By design, a personal alpha dosimeter must representatively sample all airborne particles, ranging in size from the unattached fraction to the upper limit of respirable aerosols (0.001 to 5 µm). The dosimeter must offer minimal resistance to the penetration of these aerosols. While the mining/ milling environment presents harsh conditions which may accidentally contaminate the dosimeter, it is important to be able to distinguish these cases of contamination and still obtain accurate readings. 3. A dependable dose register is most valuable for further epidimiological studies. The dependability of such a data base increases with the possibility of a second assessment of the dosimeters' reading (filter, film).

Jan 1, 1981

By John Bley

White Pine Copper Company operates a mine in the Upper Peninsula of Michigan using a modified room-and-pillar system for extracting ore.1 Mine production averages 15, 500 tons per day. The terrain is predominantly level and the depth of cover varies from 500 to 800 feet over the present workings with depth increasing as mining progresses down the dip. The deposit is situated on a low angle plunging, anticlinal structure composed of sedimentary beds. Local terminology for the stratigraphic units which contain the ore horizons, named in ascending order, is as follows: lower sandstone, parting shale, upper sandstone and upper shale. The ore zones of copper enrichment are, contained in the parting and upper shales. The parting shale will vary; from 6. 5 to 9.0 feet thick; the upper sandstone from 2 to 10 feet; and the upper shale from 1. 5 to 6. 5 feet. Two variation of the room-and-pillar system are used to extract the ore depending on grade and local ground conditions. One system is called the parting shale method and recovers the parting shale only. This system requires a mining height of 8 1/2 feet to accommodate large-scale, high-capacity equipment and this working height is obtained by removing approximately 1 to 2 feet of the barren lower sandstone with the ore. Under the second system, locally termed full column, the mining height is about 14-1/2 feet and this system removes the parting shale, the upper sandstone and the lower mineralized zone, approximately 1-1/2 feet, of the upper shale at which point it is possible to maintain a competent back (Fig. 1).1

Jan 1, 1964

Incompetent ore and country rock have caused stability problems in longhole open stopes. Fully grouted pre-placed cablebolts have reduced these by preventing ground relax- ation and joint dilation to maintain a self supporting rock structure. Larger atope spans can now be opened with the same or smaller pillar. Mining methods are expected to become less dependent on original ground conditions. Effect of spacing, orientation and stress distribution along the cablebolt is not fully understood at this stage and requires more Observation.

Jan 1, 1977

By Roger L. Keller, John Dean Smith

The Amax Coal Company's Ayrshire Mine in Southern Indiana is faced with one of the toughest blasting applications concerning vibration in the nation. As a means of maintaining regulatory compliance the operation elected to exercise the option of frequency analysis. A site-specific computer processing program which suggests ideal delay interval ranges for the lowest vibration was utilized.

Jan 1, 1987

The rapid industrialisation of the world was driven by an improved ability to utilise chemical energy. Unfortunately harnessing explosive energy did not come cheaply given the hundreds of lost lives. However, the modem explosives industry has made significant technological achievements, for explosives are now considered to be both safe and extremely effective. Upon closer inspection, it would appear the key to this achievement has been the development of initiation systems. While the focus may have been originally on safety, modem developments have concentrated upon harnessing the benefits of initiation control. Before attempting to gaze into the future, it is worth reviewing some of the significant advances that have occurred.

Jan 1, 1990

STANFORD UNIVERSITY, CALIFORNIA Our activities for the year 1918-19 have closed with the coming of summer. It has been a most successful year in many respects, especially in the reorganization necessary after the war conditions had passed. An INITIATION SCENE AT STANFORD UNIVERSITY. "old-days" initiation was held on the Stanford campus by the Society a few weeks ago. The accompanying picture explains some of what took place when the following men were taken into the membership: W. P. Winham, Salinas, Calif. ; T. L. Wark, Long Beach, Calif.; P. L. Henderson, Greeley, Colo.; T. E. Bassett, Palo Alto, Calif.; and R. G. Wheelton, Long Beach, Calif. CHAS. A. DOBBEL, Secretary.

Jan 8, 1919

By J. Desroches, J. Burghardt, B. Lecampion, A. P. Bunger

"We present detailed comparisons between theoretical predictions and experiments for the initiation of radial hydraulic fractures transverse to a wellbore. Most of these experiments provide a measure of the time evolution of pressure, length, opening and flux entering the fracture during the test. We compare all these measurements simultaneously to our theoretical predictions, thoroughly testing hydraulic fracture initiation theory, which is shown to be predictive. These comparisons notably emphasize the difference between the initiation pressure (the wellbore pressure for which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during the test). INTRODUCTION In this paper, we will compare hydraulic fracturing laboratory experiments performed in different tight materials (PMMA, cement, shale) with the predictions from a numerical solution of the governing equations of hydraulic fracture mechanics (e.g. Geerstma & de Klerk, 1969; Detournay & Peirce, 2014). We focus on transverse radial hydraulic fractures initiating from a radial notch at the wellbore wall (see Figure 1). In particular, we will clarify the difference between the initiation pressure (the wellbore pressure at which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during a test, usually carried out at constant pump rate). This difference stems from the strong viscous effects at play during wellbore pressurization, fracture initiation and early propagation (i.e. fluid entrance in the newly created fracture). It has been observed on a number of experiments (e.g. Weijers, 1995; Zhao et al., 1996) and has a strong practical application, first because the maximum pressure is the most obvious value to report and second because that maximum value is necessary to specify injection systems."

Jan 1, 2015

By Chris J. Pritchard

Pumpable, two-component resins for anchoring rock bolts provides significant advantages over traditional cartridge resin and cement grout systems where fast and easily adaptable support is required for difficult ground conditions. Cartridge resin anchoring with rock bolts is often ineffective in oversized, fractured and washed-out holes. Cement grouting of cable bolts is frequently plagued with QA and QC issues related to the grouting process. Installation of cable bolts with resin injection techniques is routinely completed in cycle allowing blasting immediately after cable bolting. Xstrata Nickel has evaluated the Minova Resin Injection System since 2007. The Nickel Rim Mine and partner Minova have tested and validated the Resin Injection process for bolting procedures including Hollow Fiberglass Bolts, Rebar, Modified Cone Bolts and Cable Bolts. The resin injection process is adaptable to most bolting processes and equipment. Currently, Nickel Rim Mine use 2 resin injection products with different set times to grout deep cable bolts and development support in highly variable ground conditions. The product predictability and adaptability in application along with a high crew acceptance continues to make this support process part of an adaptable ground support system. Product consistency and quality significantly reduce the quality control concerns for ground support in highly variable ground conditions.

May 1, 2011

By Eric C. Schwamberge, Clem A. Pelletier, Deborah L. Muggli, George W. Poling

The Pit Lake at Island Copper has evolved into a 3-layered meromictic system. Acid Rock Drainage (ARD) is collected and injected into the lake at 220 m depth via 2 diffuser systems. In situ dye studies were conducted during 2 differing hydrological regimes in order to determine the behavior of the ARD plume within the Pit Lake. Results indicated that when runoff from the waste dumps was low, the injected ARD remained within the bottom half of the intermediate layer of the Pit Lake, initially below depths of 90 m. However, when runoff from the waste dumps was high, the injected ARD at -220 m depth rose through the intermediate water column layer rapidly, but did not breach the top pycnocline at -10 m depth. Overall, the system is currently performing as a mixing bowl with a strong boundary or cap at the upper pycnocline. maintaining mixing below the 10 m depth water level.

Jan 1, 2000

By Paul R. Lear

Sustainability continues to be an important aspect of remediation and infrastructure projects. Deep soil mixing (DSM), a common construction and remedial technology, can easily incorporate the following sustainability best management practices (BMPs), including Minimizing Total Energy Use and Maximizing Use of Renewable Energy; Minimizing Air Pollutants and Greenhouse Gas (GHG) Emissions and Maximizing Use of Machinery Equipped with Advanced Emission; Minimizing Water Use and Impacts to Water Resources; Beneficial Reuse of Materials/Reduction of Materials and Waste Reduction; Use of Local Labor and Supplies. This paper focuses on the sustainability of DSM treatment and provide carbon footprint calculations at least one completed DSM project which used these sustainability BMPs to demonstrate the environmental impact of the sustainability.

Sep 8, 2021

By Peter Bates

"HIsmelt has faced and overcome many challenges in the understanding and development of injection technologies that satisfy process and engineering requirements for further scale up to a commercial plant.An overview of the design basis of bottom and top injection systems with plant results are described in this paper.IntroductionAn appropriate way to introduce this paper is to initially reflect on the genesis of the HIsmelt Process.It is appropriate that Professor Womer is the one we are honouring as it can be claimed that by the involvement of CRA in the WORCRA process that the concepts for irijection systems in iron and steel pyrometallurgical processes achieved significant attention by the company. The development of water cooled injection lances and their application injecting solids and gases with success was certainly a pre-cursor to the development of other injection systems commonly used today in arc furnaces and for top injection at HIsmelt.HistOrically it was the work of Savard and Lee in Canada with shrouded tuyeres and the subsequent commercialisation of this technology at the Maxhiitte Steelworks spawning the suite of bottom oxygen blown process as known as QBOP; OBM and the subsequent combined blowing process such as KOBM that first commercially succeeded in injecting solids under a molten metal bath. The next progressive step from the injection of calcined lime in the technology development was the injection of coal for coal gasification as developed by Klöckner technologies being called KG, KSG and KMS and also the injection of coal for increased scrap melting.A paradigm shift in thought process to leap from steelmaking and coal gasification to direct smelting by injecting coal and iron ore into a molten metal bath in the correct stoichiometric ratio to maintain the bath at a constant temperature and carbon level was the true genesis .of HIsmelt.A good overview of the state of the art of tuyere type injection technology is given in Ref. 1."

Jan 1, 1996

By Sacha Neven

Submerged lance technologies combine high intensity processing characterized by rapid mixing and reaction rates using a simple reactor design. The Isasmelt technology uses a central submerged lance to inject oxygen-enriched air and fuel into a bath thus creating large gas bubbles and intensive turbulence and splash. The lance is equipped with swirlers to increase gas velocity and heat transfer. This enables the formation of a frozen slag layer on the lance which protects it from the aggressive environment. Water models as well as high temperature reactors were used to validate the Davidson-Schiiler model on bubbling. Frequencies and pressure amplitudes were measured in a wide range of gas flow rates: from m3/sec using a water model to more than 30 m3/sec in an industrial process. Agreement with the model was satisfactory. The experiments however also clearly showed that cross-flow and bubble wake induce slightly higher frequencies. No influence of the use of swirlers on the bubbling frequency was observed in the water models.

Jan 1, 2002

By Susumu Okabe, Etsuji Kimura

"The Mitsubishi Continuous Copper Smelting and Converting Process is the typical applications of injection metallurgy to nonferrous metallurgical operation, where the top blowing multiple lance system is employed for the continuous feeding of the raw materials and reaction gases into the molten bath. This results in an effective dispersion of the reactants into a strongly agitated bath. These are considered as the major advantage of the process with respect to the high production efficiency. On the other hand, however, the strong agitation may cause a considerable amount of refractory wear, and the melt splash generated by the lancing may also have negative effects on the productivity, i.e. the increase in the refractory wear, the metal loss, the heat loss, and the accretion growth, etc. Therefore, the optimization of the blowing condition as wen as furnace design is very important to achieve a stable and efficient operation, and fundamental understanding of the injection, agitation, and splashing is badly needed.In this paper, fundamental aspects of the Mitsubishi Process regarding injection, especially splashing phenomena, are discussed. The splashing on a vertical plane caused by the top blowing gas injection onto liquid surface was investigated through physical model study. As a result of the study, the splashing rate on the furnace wan was wen correlated with the physical properties of the bath materials, gas velocity, cavity shape, lance/wall distance and ceiling position. Obtained equations were compiled in a computer program and have been successfully applied to the evaluation of the furnace design. IntroductionInjection metallurgy is an application of gas/solid-in-liquid dispersing operation to the metallurgical processing, and has been widely adopted in various fields in order to improve their efficiency or productivity. The dispersed small particles of gas or solid materials in the liquid phase result in increased interface area, and injected momentum causes an agitation and enhanced heat and materiel transfer. Typical examples of injection metallurgy are LD converter for steel making, PS converter, Noranda process, Isasme1t for copper making, and Mitsubishi Material's continuous copper smelting and converting process, and so on."

Jan 1, 1996

By H. Yin, T. Emi

"Advantages of gas/flux injection technology as materialized in the main stay unit processes for steelmaking are depicted covering hot metal pretreatment through secondary refining. Current status of micro-kinetic issues involved in the injection technology are reviewed including gas-in- metal, gas-in-slag, flux-in-metal, metal-in-flux and three-phase dispersion systems with reference to macro-kinetics. Key problems are briefly addressed to further develop injection technology for steelmaking processes.1. FROM PAST TO PRESENTApplication of gas injection to steel industry started in early 1950's when inert gas bubbling via stopper rod, lance, or porous refractory plug was practiced to make the temperature of steel melt in ladle uniform The gas bubbling in ladle was then extended to slightly removing hydrogen ti'om the steel melt tapped from Electric Arc Furnace (EAF) and Basic Open Hearth Furnace (BOH) when vacuum processing facilities were not popular. Later, oxygen gas injection via calorized steel pipe into molten steel bath in BOH Furnace was also put into operation to promote the decarburization to increase the productivity of the process. This line of development has been made in parallel with more profound processes, i.e, top blowing Basic Oxygen Furnace (BOF) for primary steelmaking and side blowing Argon Oxygen Oecarburization (AOD) vessel for decarburizing stainless steels.On the other hand, injection of fluxes into steel bath was first industrialized in Germany in 1960's, Primary objective was to desulfurize steel melt in ladle by injecting CaC2 or CaCrCaO mixture via lance under neutral slag cover with good success. Difficulties in injecting fluxes without clogging and rippling at a desired flux/gas ratio, and durability of injection lance were resolved in due time to bring forth many injection facilities to flourish for versatile refining operation. Top injection of fluxes from main oxygen lance to BOF was also industrialized as LDAC to promote early slag formation. A new process then emerged which injects oxygen gas and fluxes together through concentric annular tuyere, installed at the bottom of the BOE into steel melt. This process, developed in Germany [Oxygen Bottom Maxhutte (OBM)] and brought into maturity in USA (Q-BOP) and Japan in a large scale operation, became the predecessor of the combined blowing (top and bottom blown) BOF which dominates modern steelmaking."

Jan 1, 1996

By Erik Olsson, Gunilla Hyllander, Stefan Schuster, Lena Sundqvist Ökvist, Maria Lundgren, Michael Hensmann, Olavi Antila

"Residual materials from the integrated steel plant itself or other sources often contain valuable compounds of e.g. C and Fe. Dust and sludge have to be agglomerated to be able to recycle to the blast furnace (BF) via top-charging. By injection of the materials, preparation methods in terms of e.g. drying and/or screening only, can be used. Alternative carbon materials (ACM) in terms of BF dust and sludge have been successfully injected up to levels of 60 kg/tHM in the LK.AB Experimental Blast Furnace (LKAB EBF®). Efficiency in recovery of valuable compounds as well as the behavior of undesired elements have been evaluated and are discussed.IntroductionTraditionally, recycling of steel in-plant fines is made via the sinter plant and blast furnace route. Steel plants operating with 100% pellet as ferrous burden and have no sinter plant. There are limited areas for land fill and costs are caused for preparation of landfills and deposit fees. Very fine paniculate dusts or sludges cause decreased productivity and increased coke rate in the sinter plant, and therefore other ways for recycling must be considered. Injecting them into the BF could be an economically and technically feasible alternative. Additionally, as the materials contain valuable compounds of e.g. C and Fe."

Jan 1, 2012