Search Documents

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

"In order to achieve a high recovery of particles finer than 10µm, three types of dry Tower Mill (VD-1, KD-1, KD-2 and KD-3) have been developed. These mills differ from each other in the size of the comminuting part, the inside diameter and shape of the classifying part and the system involved in the collecting process. The last version (KD-3) of tower mills in which the comminuting and classifying operations has been separated, can produce particles finer than 10µm from a limestone ore sizing from 420 to 3360µm. In this tower mill, products in comminuting section are blown up and transported into the classifying column, made of an inverted cone on top of a cylinder, before they agglomerate and settle down. Fine particles are deported and recovered in a cyclone with a central spiral ribbon.Previous studies on the grinding efficiency of the tower mill KD-3 have shown how the maximum size of collected products increased with the airflow velocity, disturbing in the same way a smooth regulation of the grinding operation with the tower mill KD-3. A complete knowledge of factors that influence the maximum size of collected products is needed, therefore, to increase the efficiency of the grindingclassifying operation and ensure a better control over the collected products. The present study deals with this issue and, assuming that the structure of the classifying column could be one of these factors, its internal structure was modified (insertion of vertical plates, cone or horizontal nets) before carrying out comminution tests that would establish a relationship between the inward shape of the column and the maximum size of collected products. It was found that the weight of products collected in the cyclone decreases when a cone or some horizontal nets are inserted inside the column. At the same time, the weight of products collected in the column increases. This is due to the fact that coarse particles blown up from the comminution section collide with the base of the cone or the nets and settle down the bottom of the classifying column. Therefore, the cone and some horizontal nets inserted inside a classifying column, have the particularity to stabilize the maximum size of particles (15.1-17.5µm and 8.4-11.3µm) in the cyclone even when the airflow velocity in duct increased. These tools could of great help in the production of particles of definite size to fit for instance the paper industries requirements (production of limestone material sizing - 10µm as paper filler)."

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

The Tower mill KD-3 is an improved version of the laboratory mills VD-1, KD-1 and KD-2 in which the classifying column has been modified to ensure a quick discharge of products from the comminution section and, on the other hand, a better separation of coarse and fine particles; the latter being collected in a cyclone with a central spiral ribbon. To level the circling airflow through the classifying column and have a strict control over the maximum size of collected particles, a series of experiments was carried out, modifying the internal structure of the column: insertion of a vertical plate, a cone, or a horizontal net. The relationship established between the maximum size of products collected in the cyclone and the duct airflow rate indicates that, independently of the latter, the insertion of a cone in the classifying column could stabilize the maximum size of products collected in the cyclone around 15.1 - 17.5µm. With a horizontal net, the maximal size could be reduced to 8.4 - 11.3µm. This occurrence might result from the collision of coarse particles blown from the comminution zone with the base of the inserted materials and their settling down the bottom of the classifying column.

Jan 1, 2003

By X. Wu, W. R. Chen, J-G. Legoux, B. R. Marple, E. Irissou

Cold gas dynamic spray (CGDS) has been considered a potential technique to produce the metallic bond coat for TBC applications, because of its fast deposition rate and low deposition temperature. This paper presents the influence of spray processes for bond coat, including air plasma spray, high velocity oxy-fuel, and in particular CGDS, on the oxidation performance of TBCs with a Co-32Ni-21Cr- 8Al-0.5Y (wt.%) bond coat. Oxidation behaviour of the TBCs was evaluated by examining the coating microstructural evolution, TGO growth behaviour, and crack propagation during thermal exposure at 1050°C. The relationship between the TGO growth and crack propagation will be discussed.

Jan 1, 2010

By J P. Tidman

The demand for more data on the detonation properties of commercial explosives grows as blasting becomes a more exact science. Proper use of this information by blasting engineers depends on the appreciation of the assumptions and limitations inherent in calculating energies and pressures of explosives. The strength of an explosive is usually a calculated energy value derived from a model of the explosive. The model may be simple or complex, depending on the thermo-hydrodynamic assumptions made. The calculated energy and pressures of commercial explosives are sensitive to assumptions about their reaction products. The equation of state describing the reaction product gases, the treatment of solid reaction products (e.g. reacted calcium and sodium nitrate and aluminum) and the reaction time are examined to show the variability of calculated results as a result of different assumptions. These same models of explosives also serve to explain phenomena of explosives such as the effect of charge diameter on V.O.D. (and strength) and decoupled explosives.

Jan 1, 1981

By HENRT M. HOWE

IN my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson2 said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel,, the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. 'Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.' Sand vs. Iron Molds.-If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag' is much greater in the former than in the latter, be¬cause in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Dec 1, 1909

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By Jacob Carr, Chenming Zhou, Nicholas Damiano, James Noll, Jingcheng Li

Machine-related injuries are one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable was characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which causes little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects.

By Sergio Neves Monteiro, Fabio Da Costa Garcia Filho, Dian Souza de Oliveira

The properties of the nickel based superalloys, in particular 718 nickel-based alloy, are mainly improved by the hardening mechanism, which is based on precipitation of second phases. This work aimed to compare the evolution of precipitation hardening in a 718 alloy microstructure for two different solubilization conditions: 1050 °C for 2 h and 970 °C for 2 h, followed by a period up to 120 h of aging at 800 °C and correlated to the values of hardness. The microstructure was analyzed by optical microscopy. Vickers hardness test was performed and the grain size was measured. It was verified an increase on the hardeness of this material up to 15 h of aging, after that the value decreased to a level that is maintained until 120 h for both solubilization conditions.

Mar 1, 2018

By D. R. Murray

A four-year study was carried out to determine the ability of coniferous trees to aid in the reclamation of uranium tailings at Elliot Lake. Five species were planted: white cedar, white spruce, jack pine, scotch pine and red pine. More than 570 bare-root, two-year-old seedlings were planted on bare tailings and in areas of established grasses. A further division was made between areas of coarse and fine tailings. Over-all survival and growth of the trees has been far below expectations based on previous experience with several varieties of grasses. The criteria for assessment have been per cent survival and yearly growth as determined by plant height. Pine was superior, with 68% survival when planted in bare coarse tailings, 45% for vegetated coarse tailings and 34% for vegetated fine tailings. Cedar had the worst survival rates at 49%, 14% and 7% respectively. No species survived on bare fine tailings. The survival and growth of the coniferous trees have been related to species, environmental conditions and tailings properties.

Jan 1, 1978

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By Marcel Laflamme, N. R. Rillette

"In 1982, a study was initiated to investigate relationships between bonus and accidents in Quebec underground mines. In 1983, the study was expanded to include the impact of age and experience on accidents.The paper will describe the methodology followed in gathering information at ten mines from three mining camps in the Province of Quebec, and its transfer to data banks for subsequent treatment. Multifactorial analysis of nine variable files for the ten mines has shown: that age, experience and seniority are linked; that total working hours are tied with overtime; that bonus is linked to the main activity of the miner, and not to accidents. The most tangible factors affecting accidents seem to be the introductory training and subsequent retraining at regular intervals."

Jan 1, 1989

The thermal field of a frozen rockmass surrounding an airway is often disturbed due to thermal interaction with mine ventilation air. Outside air entering an underground mine changes the parameters of the physical state of the surrounding medium. The variations in air temperature result in stress redistributions around a tunnel or mine working. This paper examines the influence of fluctuations in air temperature on stress distribution around an airway, and approaches are suggested to minimize the impact of temperature- stress on the stability of mine openings in far northern mines.

Jan 1, 1991

By R Ayothiraman

Tunnel excavation may induce adverse effects on nearby existing structures/foundations in urban areas. Accurate prediction of tunnelling effects on pile foundations of nearby structures in the urban environment poses a major challenge during design. Several studies have been undertaken to understand the mechanisms of the soil-tunnel-pile interaction, which focused only on influence of tunnelling on nearby existing building and foundations. However, effect of pile loading on existing tunnels did not receive enough research attention so far. So it is essential to measure the response of existing tunnel-lining due to loading on newly constructed pile to assess to the safety against the additional forces/moment caused by pile loading and to evaluate the critical distance for the proposed construction of any structures from the tunnel location. This paper presents result of three-dimensional (3D) finite element analysis carried out in ABAQUS to investigate the effects of pile loading on existing tunnels embedded in cohesive soil. It is found that the effects on tunnel lining depend on horizontal separation distance between pile and tunnel as well as location/elevation of pile tip with respect to tunnel location.

Mar 8, 2011

By Qinghai Pang

"With the increasing proportion of bituminous coal in blend coal, the safety of blend coal during pulverization and transportation is gradually being paid more and more attention. Therefore, the explosivity of bituminous pulverized coal (PC) with different volatile content from 25 to 38% was studied by measuring the combustion flame length after its injection into a glass pipe with the heat source installed in the center. The results indicated that high volatile content bituminous PC is apt to have higher explosivity. By blending different bituminous PC with 10% anthracite, the explosivity of bituminous PC showed a positive correlation with the proportion –OH radical. However, different bituminous PC seemed to have the same explosivity when the addition of anthracite increased to 20%. With the further increasing proportion of anthracite to 30%, the explosivity of bituminous PC with high –OH proportion became negligible while a weak explosivity of high –CH3 proportion bituminous PC still remained.IntroductionWith the increasing iron ore prices and decreasing steel prices, it has become critical for iron and steel enterprises to control the cost in ironmaking and steelmaking process. Blast furnaces (BF) are the main consumer in ironmaking process, which occupies 70% fuel consumption of total steelmaking process [1]. In this circumstance, any means necessary is taken by BF operators to lower the cost of iron in production. Coke and iron ore are the main expense in this process, who takes up a very high proportion in total cost. Pulverized coal injection (PCI) is the most efficient way to reduce coke ratio, which replace coke with relatively cheaper PC.At present, most of BF is injected with blend coal in the consideration of decent combustion property and quantity of heat. Simultaneously, bituminite and anthracite blending is an effective method to obtain blend coals with required composition and performance, such as volatile and ash content, etc. Nevertheless, a very huge gap was found between the price of bituminous coal and anthracite in some regions of China, in which the price of bituminite can be just 70% of the price of anthracite. Thus, iron enterprises in these regions attempt to possibly amplify the proportion of bituminite in blend coal. Increasing proportion of bituminite results in higher volatile content in blend coal, by which the safety of blend coal during pulverization or transportation was deteriorated.Relatively, coals with higher volatile content usually possess stronger explosivity, which means that volatile and explosivity may related to some extent. However, the relationship between volatile and explosivity is not of certainty for some PC with high volatile content around 40% was found to be inexplosive in comparison to the coals with lower volatile content. With the increasing proportion of bituminous coal in blend coal, investigations on the factors of PC explosivity have become more and more important. Therefore, bituminous coals with different volatile content were selected. The explosivity of blend coal and its relationship between volatile content and functionality was investigated in this research."

Jan 1, 2014

By D J. Williams, M S. Zbik, A Shokouhi

There is a considerable difference in the particle size distribution (PSD) of clay mineral-rich coarse coal reject with variations in the test moisture state and the chemistry of the water used for testing. The coarse coal reject tested were collected from Jeebropilly Mine, located in the Ipswich Coalfields of south-eastern Queensland. Differences between the results of dry and wet sieving analysis indicate a significant breakdown of the clay mineral-rich coarse coal reject on wetting-up. Wet sieving caused a breakdown of the gravel-sized fraction to silt and clay size without significant breakdown to sand size. There is also a considerable variation in the results of hydrometer analyses of the clay mineral-rich coarse coal reject with variations in the chemistry of the water used, particularly at the fine end of the particle size range. The waters used included tap water, coal processing water and deionised water. In addition, the method of dispersion applied prior to hydrometer analysis can have a significant effect on the PSD of clay mineral-rich coarse coal reject, with boiling and sonic vibration causing the most breakdown of the clay particles. This paper describes the testing methodology used and the test results obtained, and attempts to explain the results in terms of clay mineralogy and water chemistry.CITATION:Shokouhi, A, Williams, D J and Zbik, M S, 2015. Influence of water on particle size distribution of clay mineral-rich coarse coal reject, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Y. Nishida, Y. Nara, T. Ishida

Understanding time-dependent deformation and fracturing in rock is essential, because the information of the long-term stability of rock is required for many sub-surface structures excavated in a rock mass. Time-dependent fracture propagation has been invoked as a potential key mechanism responsible for the increase in seismicity preceding earthquake ruptures. In engineering projects and in preventing natural hazards, the study of time-dependent fracturing is necessary. Subcritical crack growth is one of the main causes of time-dependent fracturing in rock. For silicate rocks, subcritical crack growth has been investigated by various researchers. It has been clarified that surrounding environmental conditions (temperature, humidity, and existence of water) have strong influence on subcritical crack growth in silicate rocks. Therefore, the information of subcritical crack growth in silicate rocks has already been enough. On the other hand, information of subcritical crack growth in carbonate rocks is not enough. Especially, the influence of surrounding environment on subcritical crack growth in carbonate rock has not been clarified yet. In this study, we investigate subcritical crack growth in carbonate rock experimentally using a fracture mechanics testing method. Marble obtained in Skopje in Macedonia is used as a carbonate rock sample. The Double Torsion method is used to measure the crack velocity and stress intensity factor. Especially, influence of water on subcritical crack growth in Macedonian marble is investigated. It was shown that the crack velocity in water is much higher than that in air at the same temperature. Based on the results of subcritical crack growth measurements, the long-term strength is evaluated for marble. It was clarified that the long-term strength in water is lower than that in air in marble. It is concluded that water has a remarkable influence on subcritical crack growth in marble. It is also considered that the long-term stability of carbonate rock masses should be ensured in a dry environment.

Jan 1, 2015

By N. S. Parate

Detailed analysis is given of the influence of water on the strength of limestone. The mechanism involved in strength reduction is described. Such analysis is of importance in geological, civil, constructional, mining, and metallurgical engineering and is closely associated with the rock mechanics involved in these areas. Mine dumping, slope stability, excavations, sedimentation, etc., are very much affected by the presence of water. Tensile stresses, which have an important role in the development and propagation of fissures, are produced by water in cracks. The development of fissures can be responsible over a long period of time for an ultimate, catastrophic failure.

Jan 1, 1974

By G. Coetzer

During galena flotation of Rosh Pinah milled material, metal ions and salts contents of various water resources (deionized, simulated circulated, lead concentrate thickener, lead tailing thickener and borehole) influenced mineral recoveries, upgrade ratios, selectivities, froth stability and flotation kinetics. The various water resources employed during galena flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed by the ore, whilst ions associated with gangue minerals (dolomite and quartz) were released into the flotation pulp. Lead concentrate thickener water caused depression of sphalerite and pyrite, increased fast floating fractions for silver, copper minerals, sphalerite and quartz (unwanted), and improved slow floating rate selectivity against pyrite and sphalerite. Lead tailing thickener water enhanced sphalerite recovery during galena flotation (unwanted), and increased fast floating fractions of pyrite. Western borehole water did not affect galena recovery, but sphalerite and pyrite recoveries were unacceptably too high. Ions from copper, lead, and zinc salts tended to release high amounts of ions, such as calcium, magnesium, silicon, and manganese from gangue minerals (dolomite and quartz) during milling. During galena flotation, lead ions depressed sphalerite, pyrite and dolomite at a lead concentration of 400 ppm, but sphalerite was activated at a concentration of 800 ppm. Sphalerite was activated with copper ions (89% recovery, 2.09 upgrade ratio) and depressed with zinc ions (maximum recovery of 25%). This corresponds with findings in previous investigations. Dolomite and quartz were slightly activated with zinc ions. No evidence was found that lead and copper ions activated any gangue minerals during galena flotation. Keywords: galena, water resources, metal ions, activation, depression, selectivity.

Jan 1, 2003