Search Documents

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT The influence of using different extraction processes (caustic versus non-caustic) on thethixotropic strength of oil sands fine tailings is examined, as is the influence of adding a coagulant tocaustic fine tailings. The thixotropic strength of fine tailings at large void ratios manifests itself as a bonding or gel strength that has been widely noted both in the laboratory and in the field. This gel strength has a significant influence on preventing the initial consolidation or settlement of fine tailings. Differences between the fine tailings’ thixotropic strength development are explained based on their physical and chemical characteristics.

Jan 1, 2010

By J. J. K. Daemen, C. Fairhurst

Introduction The stress field around a supported tunnel can be considered as being composed of: i) the virgin (pre-mining) stress in the rock ii) the (elastic) change in this stress field caused by creating the opening iii) the (time-dependent ) change in the stress field produced by (i) and (ii) as a section of the rock breaks up iv) the (time-dependent) influence of the stress build-up in the support. Several authors have examined the conditions necessary to produce static equilibrium between the support, the rock, and the regional (in-situ) stress field. The analysis used by Labasse (1) is typical. Consider a circular tunnel radius R in a hydrostatic stress field (P), and a radial pressure pi exerted by the support. According to Labasse, the radius ‘b’ to which the rock will break* for a given support pressure, pi, can be calculated from: - the equilibrium equation: [ ] As a zone of broken rock develops around the opening, the stress circle for a point on the elastic-broken rock boundary moves to the right in the Mohr diagram until the radial stress in the broken zone s equal to the radial stress in the elastic zone.

Jan 1, 1971

By Edward J. Bagnall

The major raw material feed properties of size distribution and chemistry are examined in relation to their effect on sinter operating conditions, plant productivity, sinter physical quality, reduction- degradation characteristics and sinter texture and mineralogy. The resultant physiochemical properties of these sinters are related to their behaviour in subsequent ironmaking operations.

Jan 1, 1977

By P Hunger, H Günter, F Heinicke

High pressure grinding rolls (HPGR) have been used for more than 20 years to grind iron ore pellet feed. Besides coarse comminution (crushing), where HPGR are installed upstream of the ball mill, there are numerous flow sheets where HPGR are used after ball milling and dewatering for re- or finish grinding.There is a clear growing interest in grinding of pellet feed with HPGR during the last few years. In addition to their known advantages of low specific energy consumption, high availability, low steel consumption and improved pelletising processes the lower environmental load (reduced or no water consumption) became a strong driving factor for the application of HPGR in pellet feed grinding.This growing demand increases the interest in better understanding of the HPGR grinding process with fine iron ore concentrates. One of the most important process parameters is the moisture content of the feed material which influences the performance of the HPGR enormously. The HPGR can react to fluctuations of the fresh feed properties to a certain degree by adjusting grinding force and roller speed. Nevertheless, there are limitations by the physics of the compression process and the capability of water absorption by the concentrate. The capability varies for different concentrates and different specific surface areas. This fact has to be considered during engineering of the beneficiation plant.The paper focuses on the influence of feed moisture content on the HPGR performance in view of throughput, increase of Blaine number and process stability on the basis of numerous pilot plant tests, modelling results and industrial experiences.CITATION:Heinicke, F, Günter, H and Hunger, P, 2017. Influence of feed moisture on high pressure grinding roll pellet feed grinding, in Proceedings Iron Ore 2017, pp 187–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Thomas Mütze, Frank van der Meer, Gunnar Kretschmar

"The air classification of moist bulk materials is addressed in the literature insufficiently. Therefore a feasibility study investigated the influence of feed moisture on the separation efficiency expecting a reduction with higher moisture content in the feed. Two iron ore samples were characterized in terms of the nature of bonding of moisture as well as its effect on the agglomerate strength. The classification tests themselves were conducted with two dynamic laboratory air classifiers at cut sizes from 45 to 110 µm and a moisture of the feed material between 0 to 10 wt.-%. The quality of classification was assessed by split factor, cut size, separation efficiency, moisture of both products, as well as the yield of the fines as product fraction in a corresponding processing plant. An initial approach was found for a technological implementation: A sufficient drying of a moist feed can be realized simultaneously to the pneumatic transport inside the classifiers. In the present case the drying effect and dispersion intensity was sufficient to provide good separation results up to 3 wt.-% feed moisture. An additional drying step was necessary beyond 3 wt.-%.INTRODUCTIONSpecific information about the influence of moisture in air classifiers is very rare. Mostly only dry products are processed and/or drying prior to classification is recommended. Apart from the specific influence of the feed moisture a lot of literature can be found regarding air classification itself. Altogether air classification can be divided into several sub-process (Leschonski, 1977):- dosage of the feed material,- dispersing the solid feed material into a gas stream,- feeding the dispersed material into the classification zone by pneumatic conveying,- separation of coarse and fine particles, and- separation of fine particles from gas.For wet feed particles also drying plays an important role. Interesting for the present investigation are the humidity of the feed and its influence on the single sub-processes."

Jan 1, 2016

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By Thibaut Pannetier, Damien Rogat, Catherine Larive, André Regnard, David Chamoley

"INTRODUCTION For several decades, the use of fibre-reinforced sprayed concrete (FRSC) has been becoming increasingly widespread, either as a replacement for or in addition to traditional reinforcements. Macro-synthetic fibres appeared on the market at the same time as metal fibres (in the 1980s), but their use has developed more recently in France, starting in the early 2000s. While their properties are attractive for underground operations, their long-term performance remains the subject of some controversy, particularly with regard to the phenomenon of creep [1-5]. Unfortunately, the many differences of protocol among the studies carried out (materials, metering, spraying equipment and test methods, etc.) mean that, in general, the results cannot be compared. Although several methods have been developed to assess the bending creep behaviour of fibre-reinforced concrete, the majority of them test notched beams resting on isostatic supports. There are currently no standardised test methods adapted to FRSC on hyperstatic supports (as is the case for FRSC used for underground support). The Asquapro association has thus developed a new test specially designed for this type of concrete. Slabs of thickness 10cm, measuring 60 x 60 cm in plan have been sprayed and tested under bending stress according to a test procedure inspired by the standardised test of energy absorption capacity (NF EN 14488-5). An experimental campaign was launched in October 2014 to study the behaviour of seven types of sprayed concrete, manufactured using the same concrete matrix: six of them were reinforced with different metal or macrosynthetic fibres and the seventh with a welded wire mesh. Fourteen slabs were sprayed for each type of concrete and also for the non-reinforced concrete with the same matrix. The types of mechanical performances measured were the compressive strength and energy absorption capacity (at seven and twenty-eight days), in addition to the creep behaviour of these seven types of concrete, placed under stress on the seventh day. This article follows on from that published in the WTC 2015 congress proceedings [6]: the programme and the test methods are briefly described here and the results available at the time of writing are presented and discussed."

Jan 1, 2016

By W. G. Pariseau

Regression analysis of calculated on measured displacements were used to assess the influence of fill and fold plunge on shaft pillar mining at the Homestake Mine. These effects were neglected in the original three-dimensional finite element analysis undertaken in 1991. An average fold plunge of 15? and a 24K fill (Young’ modulus of 24,000 psi or 165 Mpa) were used in the reanalysis. Measured displacements were obtained from an array of 36 m (120 ft) multiple-position borehole extensometers installed in June 1994 and read to March 2003. Results indicate the effects of both on calculated displacements and thus on regression parameters are noticeable. However, these neglected effects would not have changed the original inference of Ross Shaft stability during pillar mining.

Jan 1, 2004

By Ruth Marlene Campomanes Santana, Michel Tieccher, Marcondes Mafacioli Pacheco, Juliano Urach

"IntroductionThe gaseous emissions of fuel burning by mobile sources are responsible for incidence and increase of many lung and cardiovascular diseases (Braga et al., 2007). These implications can watch in morbity as much as mortality, even when the levels of pollution are considerate restrained or lower. (Leite et al., 2002).Sample of mobile sources exhausts contain not only particles directly shaped by burning, but also secondary particles that results of reaction between other compounds (Burtscher, 2004).One of the principal pollutants produced by combustion process with major toxicity and raiser of adverse effects to health is the particulate material. In its constitution there are fine and ultrafine particles that can to extend deep portion of breath system, break epithelial barrier and reach the interstitial of lungs and then, to unleash inflammatory process (Arbex, 2004).The Particulate Material is employed to define a mixture of solid particles and liquid drops suspense in atmosphere. Queiroz et al. (2007) declare that this material can be divided in two types separated by size interval that together, represent the major class of disperse particles: the fine particles type of 2,5 µm de (breath particulate) and the type of earthliness particles, major than 2,5 µm to 10 µm (inhale particle). The difference of size between the particles influences on the physics and chemistry properties. They affirm that exist correlation between size of particle and heavy metals; how many lower was the dimension of particulate materials, major is the concentration of heavy metals.The inhale particulate (MP10) that is object of present study can exhibit in your composition sulfates, nitrates, amoniacal, marine salt (NaCl), soil elements (Al, Ca, Fe, Si, Ti), metals (Cd, Cr, Cu, Ni, Pb, V, Zn) and water (Queiroz et al., 2007).Recent studies have exhibit strong relation between daily levels of particulate material inhale (MP10) with diameter until 10 µm and others pollutants and one infinity of effects to health that go since total mortality of population, sicken for specific causes until congenital bad formation or even difficult win weight by the fern during gestation (Gouveia et al., 2006)."

Jan 1, 2008

By K. Esmaieli

This paper addresses issues associated with ore pass degradation caused by material impact. A series of numerical experiments, using the particle flow code, were undertaken to investigate the influence of various finger raise configuration. This has allowed the identification of favorable configurations. The results of this analysis, when coupled with field observations, can contribute to the design of ore pass systems that can prolong the useful operating life of ore pass systems.

May 1, 2009

By Dao-Wu Yang, Ju-Lan Zeng, Li-Xian Sun, Yan Yao

"The hydration heat of the pure cement, the fly ash single-dopped cement, as well as the fly ash and fluorgypsum co-dopped cement were investigated by means of micro-calorimety with an eight-channel micro-calorimeter (TAM Air). The results showed that the hydration heat and the hydration rate could be reduced significantly by fly ash and fluorgypsum. However, the reduction was not proportional to the loading of dopant. The exothermic peak of the fly ash and fluorgypsum co-doped cement was appeared earlier than the fly ash single-doped cement. As the temperature decreased, the hydration heat and the hydration rate of the doped cement were reduced, and the exothermic peak appeared later. The effects of fly ash and fluorgypsum on the compressive strength of cement were also investigated. The results revealed that the early compressive strength of concrete made up of the co-doped cement was largely higher than that of the fly ash single-doped cement. Based on the experiment results obtained in this paper, we could conclude that fluorgypsum is a suitable additive for fly ash-doped cement.IntroductionFly ash and fluorgypsum are industrial waste. In 2008, nearly 400 million tons of fly ash has been produced by coal-burning power plants in China. And it is estimated that this number would exceed 500 million at the year of 2015. Besides, every year the fluoride salt factories in China discharge more than 100 million tons of fluorgypsum. Tremendous of fly ash and fluorgypsum occupy considerable land and contaminate air and water sources [1]. As a result, comprehensive utilization of this two industrial waste has draw great attention from all over the world.Cement is the most-used construction material on earth. But the production of cement consumes huge energy and destroys the environment. This problem might can be partly solved by applying fly ash and fluorgypsum as additive for cement [2-4]. During the last decade, some papers that focused on applying fly ash and fluorgypsum as additive for cement have been published [5, 6]. However, to the best of our knowledge, none of these papers investigated the hydration heat of the fly ash and fluorgypsum co-doped cement.The hydration of cement is an exothermic reaction, which can result in serious problem for mass concrete: The interior of the concrete could reach very high temperature as the hydration proceeded [7-9]. As a result, the great temperature difference between the interior and the outer of the concrete would exist and cause serious thermal stresses. Thus, the concrete would be destroyed by the cracks which in tum are resulted from the thermal stresses [10, 11]. The heat released by the cement hydration and the hydration rate is commonly regulated by adding mixed materials or transferring additive such as fly ash and fluorgypsum [12-14]."

Jan 1, 2011

By T. A. Boyden

The Free World uranium market is now characterized by production nearly twice that of consumption result- ing in a rapid build-up of uranium inventories. Low- cost production from high-grade deposits in Australia and Western Canada will gradually add another 10 to 15 million pounds U308 annually into Free World production throughout the 1980's. This latter material cannot be absorbed in further inventory build-up and can only displace higher cost production. The result is a restructuring of the Free World producer industry. United States and Eastern Canadian producers have the higher cost production which gradually will be displaced from the market during this decade. As United States production declines, United States utilities must increase their reliance on foreign supplies in order to meet their needs. This paper reviews the elements that will cause the restructuring of the Free World producer industry and the expected response of the United States utility industry to that developing situation.

Jan 1, 1982

By A. M. Tunstall

Blasting is commonly viewed separately from mechanical handling and crushing. This view is misleading because the degree of fragmentation achieved by blasting can have a significant effect on the efficiency of these processes and, hence, on the overall cost of the mining operation. In this paper, aspects of blasting and crushing and their interaction are examined. A case study is also presented that dramatically illustrates the influence of blast fragmentation on subsequent processing and on the financial implications involved.

Jan 1, 1998

By A. M. Tunstall

Blasting is commonly viewed separately from mechanical handling and crushing. This view is misleading because the degree of fragmentation achieved by blasting can have a significant effect on the efficiency of these processes and, hence, on the overall cost of the mining operation. In this paper, aspects of blasting and crushing and their interaction are examined. A case study is also presented that dramatically illustrates the influence of blast fragmentation on subsequent processing and on the financial implications involved

Jan 1, 1997

By Francisco Leite, Tomi Kouvonen, Bianca Saraiva, Vinicius Miranda, Auã Oliveira

One of the main challenges facing mining engineers is to draw up a plan that can be implemented in a timely manner, taking into account the operational variability of the mine’s production processes. These plans are often drawn up based on deterministic modelling (provided there are a set of known inputs that will result in a single set of outputs), when in truth we are talking about stochastic events (the cycles involved behave like random variables and their nature may be studied and reproduced). The result of using this kind of methodology can lead to non-optimized intuitive choices, which may harm the long-term targets defined by the planning team. Based on this principle, this document investigates the simulation of the rock fragmentation process in an open pit mine to assess the stochastic behavior of the loading and haulage operating cycles. The data assessed by the simulation process were the total costs of these operations in function of the powder factor. Based on a sample set data items, it was possible to check the probability distribution of the event as a Poisson distribution, applied to the loading and haulage cycles. The simulation consists of the repeated sequenced reproduction of these events (Monte Carlo simulation), in order to find the configuration that best fits the loading and haulage operations. By integrating these systems, it was possible to better understand the influence of the blasting in these operations, and as such to reduce the associated costs.

Feb 6, 2023

By Tian Miaomiao, Cheng Yin, Shen Jun, Yu Hao, Li Yafei

Vast amounts of waste drilling mud containing heavy metals is produced during oil drilling process, which causes great pollution to the environment. Therefore, it needs to be treated until it is harmless. This study uses industrial waste and Portland Cement stabilized waste drilling mud; the unconfined compression strength, leaching amount of Pb2+ and Cr6+ ions, and pore size of the stabilized soil were tested at different times during freezing-thawing cycles. The antifreeze performance of the stabilized drilling mud with industrial waste is discussed. The results show that the strength of the stabilized soil decreases with an increase in the number of freeze–thaw cycles. The strength loss of the stabilized soil after freeze–thaw cycles can be effectively reduced by increasing the industrial waste content, especially the content of phosphogypsum in the stabilizer component. Pb2+ ions and Cr6+ ions can be effectively stabilized by industrial waste. The results of the pores test prove that the compactness of stabilized soil solidified by industrial waste residue is greater than that of cement alone.

Nov 1, 2022

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

Influence of Frothers on Bubble Shape and Velocity Close to the Generation Point

Sep 13, 2010

By R. D. Hansen, R. R. Klimpel

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers and some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1987

By Z. Khan

Iron, in the form of steel and stainless steel, is the most commonly used metal in the world. Plain steels corrode and oxidize easily, while stainless steels exhibit improved corrosion and oxidation resistance. It has been found that rare earth metal (REM) additions, such as cerium and erbium, result in the improvement of the abovementioned properties in iron-containing compounds. Gadolinium is a REM, however, there is very little information available on the influence of gadolinium on the microstructure and mechanical properties of iron-containing compounds. Thus, the purpose of this research project was to determine the influence of gadolinium additions on the microstructure and mechanical properties of mild steel and 316 stainless steel. Ten alloys were produced for the purposes of this research. Five of the alloys had a base composition of mild steel while the remaining five had base composition of 316 stainless steel. The alloys for each of the base composition contained gadolinium additions of 0.1, 0.5, 1.2, and 5 weight per cent. The as-cast and the cold-rolled alloys were analysed. The alloys responded well to the cold-rolling with the exception of the 5 weight per cent gadolinium mild steel and stainless steel alloys. These alloys were extremely brittle and underwent a significant amount of cracking during the cold rolling process. A microstructural analysis of the alloys was conducted using a light optical microscope, while the chemical analysis of the alloys was conducted using energy dispersive x-ray spectroscopy (EDS). The resulting microstructures and EDS analyses revealed that the gadolinium displayed minimal solubility in the ferrite matrix of the mild steel alloys and minimal solubility in the austenite matrix of the stainless steel alloys. Instead the gadolinium formed as an interdendritic secondary phase in both alloys. EDS analysis revealed that the secondary phase in both alloys was gadolinium-rich. Vickers microhardness tests conducted on both alloys revealed that the alloys were composite-like, with a hard, brittle gadolinium-containing compound dispersed throughout a softer, more ductile matrix. The corrosion resistance of the alloys was determined through potentiodynamic anodic polarization tests. Two solutions were used for the corrosion rate tests: a 0.5 weight per cent NaC1 solution and a 0.5 M H2SO4 solution. The results from the mild steel alloys revealed that in both the solutions, the corrosion potentials and the corrosion resistance of the alloys increased with increasing gadolinium concentration up to 1 weight per cent. The corrosion rate test results from the stainless steel alloys revealed that the passivation current density and corrosion resistance of the alloys increased with increasing gadolinium concentration in both solutions. The oxidation resistances of the mild steel and stainless steel alloys were determined through the use of a Netzstch Simultaneous Thermal Analyser. For both the mild steel and the stainless steel alloys, it was found that the oxidation resistance of the alloys increased as the concentration of gadolinium increased when compared to the as-received mild steel and stainless steel samples. This could be due to a strongly adhering gadolinium oxide scale that formed on the surface of the alloys and resulted in the protection of the mild steel and the stainless steel.

Jan 1, 2012