Search Documents

By Kent S. Roessler

The Bureau of Mines is currently investigating the geophysical application of Tomography to monitor leachate during in-situ mining. Determining the location of the leachate is important for both economic and environmental reasons. By analyzing a sequence of tomographic images, we can determine where highly permeable/fractured regions are located and hence, major flow paths. Since BOMTOM (Bureau Of Mines TOMography - Tomographic Reconstruction Program), and BOMCRATR (Bureau Of Mines Curved RAy Tomography - Tomographic Reconstruction Program) are sensitive to user-selected ray path arrival times, we are also investigating the use of neural networks to automate the process of recognizing this feature. This paper presents a technique for detecting fracture zones and their orientations in a region between two boreholes, by using a motion analysis study of a sequence of tomographic images. It also addresses the need for an automated/unbiased method to pick crosshole seismic arrival times using a trained neural network. In exploration geophysics, the picking of first break arrivals represents a pattern recognition task. The neural net paradigm has proved to be a good method of solving this type of task. To pick the first arrival peak of a trace, the network is trained with a set of known (user selected) first arrival peaks by creating a binary image of a set of traces. Once trained, the neural net correctly picked first arrivals of the remaining traces in the set.

Jan 1, 1992

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By F. Waanders, Campbell. Q.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite where the specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials like silica, base metals and their oxides, usually associated with gravitation-gold-recovery-processes. The ore body investigated in this project originated from a gold reef containing a large portion of gold locked inside the gold pyrite complexes, which was mined and treated in a conventional way. After gold extraction, the material was pumped to a tailings dump and the gold extraction of this dump was investigated. In order to assemble a concentration plant setup, the head grade and size distribution of the dump and bulk sample were determined accurately. Chemical analysis and mineralogical examination were done on a representative sample of the bulk sample, to determine the chemical composition of the material. The results obtained thereof were evaluated and a pilot plant was configured. A bulk sample was processed in the pilot plant and the results were evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes.

Jan 1, 2014

By G Kirk

Definition and delineation of in-pit ore and waste material are the most significant tasks for an open pit production geologist; adding or destroying value in the mining value chain. Anglo American’s Mogalakwena Platinum mine, an open pit operation in South Africa moving 100 Mt/a, has recognised the value of improved material definition and is in the process of changing from blasthole to reverse circulation (RC) sampling for in-pit grade control. This is aimed at obtaining more representative samples, which are required to maximise ore recovery, minimise waste dilution and to increase the accuracy and confidence of production forecasts. Early in the project, it was realised that the key risks for implementing RC grade control were related to change management processes, rather than failure of technology. Recognising the importance of this issue, Mogalakwena chose an integrated implementation approach that incorporates all stakeholders of the mining cycle in order to develop a process that delivers maximum value and is sustainable within an active mining environment. The following core goals were addressed over five phases of project implementation: extensive definition and design of integrated project implementation, comprising: project buy-in and ownership from all key stakeholders, including survey, geology, mine planning, drill and blast, load and haul, maintenance, supply chain and finance; and detailed analysis of all potential issues and possible solutions, allocated to stakeholders as part of the scoping process; optimising hole patterns and drilling procedures, focusing on delivering maximum value for minimum cost using multiple scenario analysis from borehole data and operational sequencing requirements; and evaluation of lessons learnt during project implementation in order to optimise the technical solution and operational efficiencies. Although this project is not yet finalised, Mogalakwena Platinum Mine is already providing a blueprint for the effective development, implementation and optimisation of sustainable in-pit grade control RC drilling for other open pit mines within Anglo American plc.

Aug 22, 2011

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003

By B Upton, J Mitchell

The use of hydro scaling and in-cycle shotcrete to replace conventional jumbo scaling, mesh and bolting as the primary method of ground control for run of mine development has been investigated through extensive trials at the Waroonga mine, Agnew Gold Mining Company.These trials have progressed from investigating the productivity aspects of the method through to a three month mine-wide trial, which may yet lead to the adoption of this potentially best practice ground control technique at Agnew.Ov erseas trials and research have shown that hydro scaling results in a significant improvement in the shotcrete-rock bond strength. Good adhesive bond strength ensures that the shear strength of the shotcrete layer rather than itÆs flexural or tensile strength is fully mobilised as rock mass reinforcement.This maximises shotcretes ground reinforcement capability and it is suggested that a bolt-less fibrecrete support design is feasible using the hydro scaling technique.

Jan 1, 2005

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By T Kilpatrick

Managing heat stress on Australian mine sites is a complex and enduring challenge due to the combined and variable contribution of environmental conditions, physical activities, and protective equipment. Inappropriately managed, heat stress can place significant physical strain on workers, leading to serious and chronic health issues. Additionally, excessive heat stress can dramatically reduce productivity, with 30 per cent of workers reporting a loss of productivity due to occupational heat strain. In Australia, due to increased absenteeism and reduced work performance, heat strain is estimated to have an annual economic burden of over $8 billion.

May 5, 2022

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By Qian Li, Haiyan Leng, Kuo-Chih Chou, Haoyuan Xiao, Zhigang Yu

Magnesium borohydride and Magnesium alanate were synthesized by mechanochemical metathesis reaction. The thermal decomposition behaviors of Mg(BH4)2-nMg(AlH4)2(n=0.5,1) systems were investigated as potential hydrogen storage materials. The results showed that the systems started to desorb H2 at 120 ℃ and desorbed 3.9 wt. and 4.9 wt.% H2 below 300 ℃ when n equals 0.5 and 1, respectively, while individual Mg(BH4)2 started to desorb H2 at 250 ℃ and desorbed only 0.82 wt.% H2. Because of the exist of the Mg(AlH4)2, the isothermal desorption kinetics of Mg(BH4)2 in the Mg(BH4)2-0.5Mg(AlH4)2 systems was 50% faster than that of pristine Mg(BH4)2. In addition, the re-hydrogenation rates also increased 49.4% and 37.9%.

Jan 1, 2015

Develop a curved ray geotomographic program with constraints to counteract non-uniqueness in order to improve the reliability of seismic tomographic imaging of geological structure in mining regions. Background Seismic tomography provides a two-dimensional image (tomographic reconstruction) of the distribution of the seismic velocity in geologic structures using measured travel times of seismic waves crossing the area. It can provide a more complete representation of features be¬tween boreholes than other crosshole processing methods that measure only average properties or borehole logging methods that measure properties only near each borehole. Seismic tomography has many mining applications. They include locating geologic structures of contrasting seismic velocity, detecting fractured regions where the seismic velocity is low, and monitoring solution injected above the water table where the increase in saturation increases the seismic velocity. Thus, tomographic imaging techniques show great promise for detecting and locating geologic hazards that affect the productivity, safety, and environment of mining operations.

Jan 1, 1992

By Jeffrey D. Oke

While significant progress in underground construction engineering has occurred in the past few decades, a number of fundamental deficiencies persist regarding the recognition, prediction, and mitigation of underground construction hazards associated with complex geological conditions in rock and soil works, such as tunnelling. Many of these shortcomings could be addressed by improving geomechanical models which, in turn, would provide more realistic frameworks for determining input parameters for design analysis. This would improve predictions of construction efficiency for tunnelling and the formulation of more accurate modelling techniques (2D, 3D and 4D) required to optimize the design of engineered rock structures. This research focuses primarily on the issues related to forepole temporary tunnel support within weak rock masses. This research attempts to determine how best to numerically model forepole support. The behaviour and mechanics of forepole support has not been quantified and/or optimized. As well, there is a lack of in-situ and/or laboratory forepole and weak rockmass interaction parameters available. In terms of numerical modelling, there is a lack of understanding of the use of proper interaction parameters associated with the forepole and the rockmass. The parametric study that has been conducted by the authors demonstrates the influence of each of the forepole-rockmass interaction parameters and their sensitivity. Introduction

Jun 1, 2012

By Stefan Zanon, Ty Faechner, Clayton V. Deutsch

Secondary data are important in geostatistical simulation of continuous variables. Geophysical data and geological trends are used for modeling porosity and permeability. Multiple mineral grades must often be modeled for mining applications. Sequential Gaussian simulation (SGS) is often used because of its relative simplicity and robustness. The two most common approaches to integrate secondary data in Gaussian simulation are with (1) locally varying mean, or (2) collocated cokriging. A significant problem with both of these techniques is variance inflation, that is, the variance of the resulting simulated values is too high because of an inappropriate decision of stationarity or an artifact of choosing a single secondary data in presence of many. We introduce a self-healing procedure for dynamic correction of this problem. The dynamic correction is different for the locally varying mean approach and for collocated cokriging since there are different reasons why each of these methods causes variance inflation. The reasons for variance inflation are discussed and the self-healing is applied to a number of data sets.

Jan 1, 2002

By G. R. Corbett

The introduction of roof bolts to Phalen Colliery in the Sydney Coalfield, Nova Scotia (annual output of 2Mt) has been successfully implemented in maingate and tailgate entries over the last four years. Monitoring of the roof bolted areas continues to be an integral part of the quality control program as the results are utilized to maintain safety and to aid in long-term design strategies. Although all gateroads in the Phalen Colliery have converted to roof bolts as their primary means of support, the majority of intersections which intersect the main slopes remain supported by large steel structures. Several intersections within the Phalen Colliery were monitored as they were created by the mining process. A comparison is made between intersections supported with only traditional 6.4 to 6.7 m steel structure and intersections supported by 2.44 m fully resin encapsulated roof bolts in conjunction with 7.6 m fully cement grouted cable bolts. Detailed monitoring was conducted using CA NM ET's intrinsically safe sonic probe extensometer datalogger which has the ability to read up to sixteen probes simultaneously at programmed intervals. The density of the data from the datalogger has allowed a better understanding of the deformation of cable bolted intersections than was possible with manual monitoring. Test results have helped mine operators to design safer cable bolted intersections.

Jan 1, 1995

By H Kurth

High specification Prompt Gamma Neutron Activation Analysis (PGNAA) has been successfully applied to conveyed flows at iron ore operations since 2002 to representatively measure ore quality for improved quality management and process control. While the PGNAA technique has changed little since that time, significant improvements have been made in measurement capability. Elements previously unable to be measured well or at all using this technique are now measurable and one of these is phosphorus. Aluminium and magnesium are also key elements in addition to calcium and silicon in determining sinter basicity in ironmaking. Other elements measured routinely in iron ores include iron, carbon, potassium, sulfur and manganese. The benefits of representative measurement cannot be overstated as iron ore mining operations in South Africa, Europe, Australia, Asia and the Americas have discovered. The technology is applicable to any conveyed flow where elemental analysis in real time assists with quality management, from raw materials in ironmaking through to scrap steel in steelmaking and coal quality for coke-making. Major benefits are realised when raw material processing is optimised and this often includes diversion of material meeting a required quality so it can bypass unnecessary processing. This includes waste rock which can be diverted from a plant feed stream in 30 sec increments or ore that meets product quality being diverted to bypass beneficiation. Analysers are successfully utilised to identify ore types that assist with upgrade optimisation in jig plants; measuring feed, product and discard flows to also account for metal content. Product flows to stockpiles help manage production flows and stockpile qualities for different products and assist in blending ores into trains or ships to confirm specification compliance. Technologies can be used in magnetite processing but are predominantly used in hematite and goethite ore processing operations. The paper details examples of the above applications at various operational sites providing estimates of economic benefit as well as operational improvements.

Sep 18, 2023

By Guy Chevalier

The QCM Mount-Wright mine and concentrator complex produces about 14 M tonnes of iron concentrate annually. Approximately 9.5 M tonnes of this concentrate are used to produce iron ore pellets at four different silica grades: Three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the realization of two projects where the acquisition of new process equipment led to an improved pellet plant iron recovery, a better flexibility and to lower operating costs as well as to the production of fine iron ore concentrate from the Port-Cartier tailings pond. Typical 4.8 % SiO2 concentrate is processed to achieve required pellet silica content. This is obtained with the aid of hindered settlers or hydraulic classifiers, screens, whims and, lately, spirals. The increasing demand for low silica iron ore products resulted in a greater need for upgrading. The Pellet Plant upgrading capacity being limited, more and more iron units were lost. Base on test works results and economic evaluations, QCM engineers figured out a way to increase efficiently their upgrading plant capacity and go back in the pond gather what has been lost in recent years of operation.

May 1, 2007

By BTrubT M

In the roast-leach-electrolysis process for the production of zinc, iron contained in zinc concentrates is converted to zinc ferrite during roasting. At Canadian Electrolytic Zinc (CEZinc), the Outokumpu Conversion process is used to simultaneously leach zinc ferrite and precipitate the iron as jarosite. These simultaneous reactions, while providing good process stability, require a compromise between optimum conditions for maximum zinc extraction and efficient iron precipitation. An improved conversion process has been identified which can achieve >99 per cent zinc extraction and more efficient jarosite precipitation to residual iron concentrations of

Jan 1, 1993

By J. R. Cobble

The Bureau of Mines has developed a process to improve the leaching kinetics of diffusion controlled systems. The system features the Bureau-developed turbomill, an attrition grinder which scrubs the reaction product coating away from the unreacted mineral grains during leaching. The system can be continuously operated at any temperature up to the boiling point of the leaching agent. This paper describes the research on the dissolution of chalcopyrite with acidified ferric sulfate which forms a sulfur product on the unreacted chalcopyrite surface. This method is a hydrometallurgical alternative to chalcopyrite smelter technology which eliminates S)2 emission problems with its associated costs. Batch testing at 90? C with the chalcopyrite/ferric sulfate system resulted in better than 99-pct extraction of copper. At an optimal energy consumption of 1,520 kW h/st, 95 pct of the copper was extracted. Recent work has been directed to development of a continuous system and SX/EW treatment of the resulting pregnant liquor from the chalcopyrite/ferric sulfate leach.

Jan 1, 1991

By J. Kang

To obtain microbial cultures with the ability to efficiently leach copper ion from chalcopyrite, microbial samples from acid mine drainage sites were mixed and then subjected to mutation using sodium nitrite (NaNO2), diethyl sulfate (DES), ultraviolet light (UV) and their combinations. Mixed cultures with a much stronger ability to leach copper ion (identified as mixed cultures A, B, C, D and E) were obtained by screening on leaching media. Leaching tests showed that mixed culture E had the best leaching performance and increased the Cu2+ content by 120.5% in 20 days, compared to a control without mutation treatment. Mixed culture E grows well on Leathen leaching medium supplemented with Cu2+ (at a final concentration of 32 g/L), reaching 3.2 × 107 cells/L after 15 days, while the unmutated control culture cannot survive beyond 15 days, indicating that mixed culture E is more tolerant of high concentrations of Cu2+. In addition, continuous leaching by mixed culture E is very effective at a pulp density of 1%. These results suggest that it has the potential for industrial applications.

Jan 1, 2008