Search Documents

By J. T. Winkelmann

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately twenty miles northwest of Kingman, Arizona. The concentrating facility has been regarded, with the expansion in 2011, as a plant capable of treating fifty thousand short tons of feed per day for the mixture of supergene and hypogene ores available. The grinding circuit consists of two 32? x 14? SAG mills and four 20? x 28? ball mills. As ores became harder with greater depth in the adjacent pit areas, however, the SAG mills became severely throughput limited. The traditional treatment for similar properties is the installation of a recycle pebble crushing circuit. Because the cost of such an installation is quite elevated, and preliminary testing and research was inconclusive regarding the predicted throughput increases, management and technical personnel set out to find another solution to the problem. The result entailed a redesign of SAG lifters/liners and a nearly unique circuit change which was, at best, a difficult step that defied current grinding logic. This paper describes these changes, events leading up to them, and the results.

Feb 23, 2014

By E. G. Banks

THIS paper is presented in the belief that metallurgists and chemists will be interested in the practice of grinding in tube-mills in connection with stamps, especially since the records of working here given extend over a lengthy period of time (since May, 1905). The ore from the Waihi mine-more especially that produced in the upper levels-contains a large proportion of hard, chalcedonic quartz, and the gold exists in an exceedingly fine state, conditions which necessitate very fine crushing in order to ob¬tain a high extraction of the precious metal. Before the introduction of tube-mills at the 90-stamp Waihi mill, it was found necessary to stamp through 40-mesh (1,600 holes per sq. in.) woven wire-screens, having a fairly high discharge. The pulp then graded

Jan 1, 1907

By E. M. Furness, A. S. Henderson

ORIGINALLY the Babbitt experimental plant grinding circuit consisted of one rod mill 10 ½ ft diam by 12 ft long in open circuit followed by two ball mills 10 ½ ft diam* 12 ft long in parallel circuit. Shortly after operations commenced it was apparent that the rod mill could not function satisfactorily at the required 125 gross tons of ore per hr. Attempts to operate at this rate produced: 1) excessive tramp material over rod mill trommel screen which could not be handled in this open circuit and 2) excess build-up of coarse ore in the ball mill circuits because of inadequate rod mill grinding. Since Reserve Mining Co. ore must be ground to 85 pct -325 mesh to produce a satisfactory iron concentrate, an efficient and controlled grinding circuit is highly important. The first step in trying to resolve this grinding problem was to determine which unit of the circuit was actually in trouble and to what extent. A series of tests conducted at a lower tonnage rate of rod mill feed indicated that one ball mill could grind satisfactorily at rates up to 70 gross tons of rod mill feed per hr.

Jan 12, 1957

By H. M. Howard

"The subject of Grinding Media is perhaps still quite controversial. Many people will state today that the spherical ball is the only way, and also will state that this was settled long ago others are not so sure, and I am in this second category. Over the years there have been many changes in grinding and in our evaluation of grinding media we should always be ready to review the overall situation at regular intervals. There is quite a lot of inertia in all branches of Hineral Dressing and this is particularly true of grinding or, more correctly, comminution.In order to understand some of the things which are done today, and to understand some of the thinking on grinding, it is desirable to go back some sixty years and trace the developments in comminution. In doing this we should consider perhaps three general categories with respect to daily tonnage. An arbitrary division would be under 500 T.P.D., 500-5000 T.P.D., and large operations which might have several parallel units, each with a capacity of about 5000 T.P.D. For the future, in the broad picture, this last category will be the important one because we will be more and more dependent on large-tonnage low-grade operations for most of the metals of the future. Some such division is necessary because the daily tonnage will have a very great effect on what we can and cannot do. It is also necessary to consider the entire flowsheet, and to remember in particular that grinding is not merely to make small particles but is also a conditioning process, to prepare the materi.al for the process which follows. The relationship of crushing to grinding must also be considered. It is logical to include the liners as part of the grinding media and we should try to distinguish between the wear of grinding media and the consumption of media by corrosion. Finally, the whole question of grinding media should be examined in relation to the possibilities of using some form of autogenous grinding."

Jan 1, 1970

By M. D. Baker

Coal-water slurry preparation requires fine grinding and cleaning of coal by flotation. Finer grinding leads to increased ball wear and its effect on the surface properties of coal becomes of concern. Marked ball wear tests were performed to study the effects of oxygen, pH, the soluble species of coal and the addition of pyrrhotite on ball wear. The synergistic action of coal and oxygen greatly enhanced the corrosion of mild steel balls during grinding. Electrochemical measurements on a mild steel electrode in coal slurries and SEM observations of grinding ball surfaces were carried out to explore the corrosive wear mechanism.

Jan 1, 1989

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994

By R. Tessier, R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. The paper presents findings in the on-going testing of various sizes and shapes of grinding media. Breakage rates are used as an aid to assess the effect of grinding media. Results of empirical and phenomenological analyses demonstrate the importance of adequate selection of media sizes on the milling operation.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mine near Bathurst, New-Brunswick. The No. 12 ore body is an extremely fine grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite. The operation is currently processing 10,500 tonnes of ore per day in conventional crushing, grinding, differential flotation and dewatering circuits. Details on the circuit can be found elsewhere (e.g. Hendriks and Ounpuu, 1985; Grant et al., 1991).The mill has operated for more than 25 years and despite the past milling experience, there has been much disagreement as to the required grind size. Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37µm) and averaged slightly over 71%in1992. Results from mineralogical analysis (Petruk and Schnarr,1981; Coleman, 1988), Brunswick metallurgical laboratory (Grant et al., 1991; Shannon et al., 1992) and Lakefield pilot plant tests (Hendriks, 1984; Hendriks and Ounpuu, 1985) clearly indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15-25µm range."

Jan 1, 1993

The current global economic climate has adversely affected the resources industry in general. For the gold mining industry, even though the gold price has been stable as compared to other resources, there is still a need to cut costs even further in order to be profitable and sustainable. Of all the costs that are associated with mining, comminution of ore accounts for the majority. Comminution costs constitute mainly electricity, grinding balls and liners. Of these three components, grinding balls form the major portion of the consumable costs, and can be as high as 40%?45% of the total. As a result, proper grinding ball selection is a key consideration towards reducing mining costs. This paper discusses quality control procedures that can be conducted in order to select the best grinding balls for a particular application. Keywords: grinding balls, forged, semi steel, hardness, chemical, metallography, wear testing, impact test

Jan 1, 2009

By Vathsala Rajagopal, lwao lwasaki

The grinding media materials for the mining industry require corrosion and abrasion resistance properties not only to minimize the wear but also to improve the flotation recoveries of sulfide minerals. The media wear mechanisms and the factors influencing the grinding ball wear during grinding are discussed with respect to abrasion, corrosion and impact wear of grinding media materials. Interactions between the grinding media and sulfide minerals in a ball mill adversely affect the floatabilities of the ground minerals. The possible galvanic interactions between grinding medium-mineral and their effects on the flotation responses of sulfides are also reviewed. The selection criteria for alloy composition that reduces the overall wear along with adverse effects on flotation are brought out.

Jan 1, 1992

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By J Kinal, P Steinier

A considerable volume of work exists in the literature examining the electrochemical interactions between grinding media and sulfide minerals. Broadly, most sulfide minerals are more noble than forged steel grinding media used during comminution, therefore a galvanic couple between the media and the sulfide mineral(s) exists, which increases the corrosion rate of the grinding media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulfide minerals thereby affecting their floatability. This paper explores the science behind these corrosion reactions, and provides an explanation of their impact on the pulp chemistry of sulfide mineral slurries and subsequent flotation behaviour. A number of laboratory and plant case studies are used to illustrate the benefits of changing to a more inert grinding media.

Jan 1, 2005

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

By R. E. Sabaski

Total grinding mill system life is dependent upon the original selections and specifications of its components: the mill, its drive, drive motor, motor control, and power system. This paper discusses the complex considerations involved and the critical decisions which must be made by the buyer, the mill manufacturer, and by the gear vendor during the proposal and ordering stages. Interrelations between the mill manufacturer and the gear vendor, application of ACMA standards, how drive standards and specifications are refined through steady-state and computer-simulated torsional analyses are included, along with correlational field testing, as demands for larger sizes challenge the current state of the art.

Jan 1, 1984

Grinding Mill Operation and Maintenance - Central to Asset Management Since 2005, RME has pursued a vision for a new grinding plant operational paradigm, made possible by RME's latest Mill Relining Systems. At some sites, new liners degrade SAG mill performance. The variables include mill volume loss, rotational speed limitations (ball strike) and liner designs developed for longer and longer life but without a backward glance at metallurgical consequences of whole plant performance. Freshly relined mills can initially deliver as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the liners' wear life. RME's proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and relining speed become key profitability contributors and not simply 'must do' maintenance functions and costs. This paper includes a short history of RME's Mill Relining System development (Appendix A). These are the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The body of this paper outlines RME's vision of a 'liner profile vs. profitability' commercial model, underpinned by the rigour of PAS 55-1:2008 Asset Management Part 1: Specification for the optimised management of physical assets. The technical elements can be developed either intuitively (based on plant experience) or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum technical solution for the maximum commercial outcome. Much of this can be modelled off-line, in the virtual world, before asking senior management to commit to an expensive liner experiment. The potential benefits are compelling.

Sep 13, 2010

By S. McTavish

Since mechanically suitable grinding mills were available in 1908, mill operators have been searching for the best material and design with which to line the mills. These liner systems had to fulfill several criteria. First and foremost they had to last long enough in an operating mill to protect the mill structure from the abrasive wear of the ore and the grinding media. In addition they had to be able to efficiently transfer the energy from the mill to the mill charge in order to facilitate the grinding process. The liners also had to be easily attached to the mill when new and removed from the mill when worn out. The first liners used were generally made of cast white iron, Hadfield manganese, unalloyed high carbon steel and composites of steel and concrete or cemented in flint blocks or natural stone. 1

Jan 1, 1989

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

By C. G. McLachlan

Laboratory flotation tests carried out on massive sulphide ores may not be reproduced in plant practice, and when this occurs the discrepancy can be the result of differences between laboratory and plant grinding. Results of parallel flotation tests are given to support this contention, and data show how tailing losses are affected in corresponding size zones.

Jan 4, 1951

By J. George Gregr

"This paper gives a brief review of grinding mills installation procedures with special emphasis on future maintenance. The importance of cooperation between the customer, construction contractor and manufacturer's representative is discussed, as well as the imparlance of complying with standards, specifications and the keeping comprehensive installation records.Fundamentals of mill maintenance are explained with the aim being to maximize the equipment availability and to minimize unscheduled downtime. The paper also includes development of wear items design, based on operating conditions, drive components and bearings, and how to keep large gears healthy thus eliminating surprise failures.Experience with installation of a large gear on a 34-foot diameter mill in Lornex and successful application of a computer program for the gear alignment on the mill are given.IntroductionSuccessful operation of a concentrator begins with the engineering of the project and continues through selecting the right equipment, its installation , start-up period, and ends with final tuning of the process. machinery and the human factor into an efficient and viable industrial complex.The following is a brief review of grinding mill installation procedures with special emphasis on future maintenance. Fundamentals of mill maintenance are discussed with the aim being to maximize the equipment availability and to minimize unscheduled downtime, with some specific points on key grinding mill components such as bearings and drives.Finally, the experience is recounted with the installation of a large ring gear on a 34-foot diameter mill at Lornex, and the successful application of a computer program for the gear alignment on the mill."

Jan 1, 1985

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling.INTRODUCTIONThe early 1900?s saw the beginnings of published papers which tackled the problem of what influenced the power draw of tumbling mills and what equations (models) were suitable for predicting power draw. This interest continued for the rest of the 20th century and the literature contains many papers that attempted to satisfactorily answer these questions. A common and disappointing theme in the majority of them, however, is the distinct lack of suitable experimentally derived power draw data. This deficiency consequently limited the practical application of many of the attempts at modelling mill power draw. Prior to the early 1990?s some limited data on the power draw of grinding mills in the literature can be found, but as Harris et al (1985) remarked they are ?... too frequently unusable simply because one or more essential variables have been omitted?. The absence of published results, from vigorous experimental testing of the various models, has resulted in a general lack of evaluation of the validity of assumptions and hypotheses that such models contain. Harris et al (1985) however, did make some efforts in attempting to evaluate the performance of various power prediction equations and in so doing further developed a semi-empirical one of their own. However, in using manufacturers? published data, which themselves were undoubtedly generated by proprietary equations of unproven validity, they probably succeeded in generating little more than a consensus of the various errors in these models."

Jan 1, 2003

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling."

Jan 1, 2003