Search Documents

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989.Previous drilling indicated over 100 million cubic metres of gravels with some 90% of the gold in the bottom 7 metres.The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below.Metallurgical studies and exploration were initiated when the project commenced; Leasing and environmental considerations were investigated and action taken.While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

By M Simpson

Greywackes of the greater Auckland Region (Brynderwyn Hills to Hamilton), when considered on a regional scale, have characteristic ranges of physical, mineralogical and other properties. Some properties (eg density, porosity, crushing resistance, clay index) generally cluster and correlate with the basement greywacke facies, regions and terranes recognised by geologists, and their diagenetic/metamorphic level. Other local factors, particularly variations in mineralogical composition, nature of matrix cement, grain size, and degree of weathering may produce aberrant properties. Some of these local variations, when extreme, have the potential to affect the aggregateÆs performance in roading or the concrete industries.   Smectite and the zeolite laumontite are the major deleterious minerals occurring in fresh greywacke rocks of the Auckland region, although weathered rocks may contain halloysite, an expanding member of the kaolin clay mineral group. These minerals, when found in abnormally high levels in greywackes cause expansion effects in the aggregate. Currently there are inconsistencies in the detailed correlation of shrinkage, clay index, clay mineral content and intrinsic expansion data that need further research to resolve them.  

Jan 1, 2007

By Masaki Kitazume

"Many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction which occur in a loose and saturated sand layer, induces quite large damages of infrastructures, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Many kinds of ground improvement techniques based on various improvement principles have been developed for earthquake disaster mitigation. Among them, the grid type deep mixing method has been often applied to liquefaction mitigation. In the method, the stiff grid walls are constructed by mixing the soil and binder in-situ, which are expected to restrict the shear deformation of the soil within the grid walls so that the pore water pressure generation can be remained small. The high applicability of the method was confirmed in several earthquakes, including the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake. In this paper, the development of the method, some applications of the deep mixing method to earthquake disaster mitigation are briefly introduced. INTRODUCTION In Japan, many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction induces quite large damages, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Table 1 shows the amount of damage to port facilities (Noda, 1991). According to the table, the amount of damage when liquefaction takes place is about 20 to 50 times larger than that without liquefaction. This highlights the importance of liquefaction mitigation to minimize earthquake disasters. There are many kinds of soil stabilization techniques developed for liquefaction in Japan. Among them, the deep mixing method (DMM), an in-situ cement stabilization techniques, was developed in 1970s in Japan and has frequently been applied to improvements of clayey and sandy soils (Kitazume and Terashi, 2013). The grid type DMM has been often applied to prevent liquefaction, where the grid of stabilized column walls function to restrict generation of excess pore pressure in the soil within the walls by confining the soil particle movement. The improvement effect of the method was first evaluated in the Hyogoken-Nambu earthquake in 1995 and was also evaluated in the Tohoku earthquake in 2011. In this paper, some successful performance of the deep mixing method to earthquake disaster mitigation in the two earthquakes are briefly introduced."

Jan 1, 2015

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By Fred Bond

This paper is a continuation of two earlier papers,1,2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a. new method of measuring the "surface energy" of in ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems.

Jan 1, 1938

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

By Baoquan An

The energy required to fragment a rock is proportional to the increase in the fracture surface area and hence is proportional to the rock?s surface area. In comminution, the slope of the linear relationship between size reduction ratio and specific energy is usually defined as grindability. Another definition of grindability based on newly created specific surface area and specific energy is introduced. The two definitions for grindability reflect the grindability properties of rocks and can be used to measure of the efficiency of mills or crushers. The feed particle size distribution influences the energy needed to comminute the rock. For a given ratio of average feed size to product size, the smaller feed size requires more energy.

May 1, 2004

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

By A. Güngör, Ü. Atalay

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By O Gutsche, Fuerstenau D. W., R. Ravikumar

Six minerals and one ore, namely, barite, dolomite, galena, limestone, quartz, quartzite and taconite, were ground in single-particle comminution mode in a rigidly mounted roll mill with different levels of energy input. Grindabilities were determined from the median size of the self-preserving product size distributions, which was taken as a measure of the fineness of the ground material in an empirical energy-reduction ratio relationship. These values reflect the inherent resistance of the solids to mechanical size reduction that are least distorted by particle-particle interference effects, grinding characteristics, energy efficiency of the milling system employed and the extent of the fineness specified.

Jan 1, 1992

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By W. L. Maxson

GRINDING is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grind-ing installations. There have been some tests published, notably those of Lennox,1 which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was .then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the compari-sons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating, load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to he expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method.

Jan 1, 1933

By C. H. Rawlins

The total amount of ferrous slag generated in the U.S. is about one-third the amount of iron ore mined, thus ferrous slag can be considered a significant mineral body for processing. Steelmaking slag contains up to 30 wt.% metal of which only the >25mm fraction is commonly recovered. A grinding study was conducted of BOF, EAF, and LMF slags using the Bond Work Index method to determine grindability to 106µm. Work Index values obtained were 13.8-24.9 kWh/ST, depending upon the slag type and composition. Steel particles were magnetically recovered from the crushed and ground samples for size-by-size analysis, yielding up to 18 wt.% of the slag weight recovered as magnetic. The recovered material, as characterized by inert gas melting, was found to be 61-96 wt.% metallic.

Jan 1, 2008

By J. W. Leonard

One of the more obvious phenomena which relate to coke formation is that soft coals of low volatile matter content tend to yield hard or high strength cokes while hard coals of high volatile matter content tend to yield soft or low strength cokes. This observation led researchers of the Coal Research Bureau of West Virginia Univ. to study the possibility of using Hardgrove grindability as a supplemental rank indicator for coking properties. Grindability has been used for many years as a means to measure the resistance of coal to comminution but it has rarely if ever been considered for evaluating coals for carbonization. The coal proper- ties which are measured by grindability are complex, but recent work with the difficult-to-correlate high volatile coals has demonstrated that a 93% correlation exists between grindability and the total petrographic rnicrinites, exinites, and resinites. This work demonstrated that inherent ash had no apparent effect on the grindability of high volatile coals, suggesting that the coal substance is apparently harder than the associated ash. These observations, together with the patented Burstlein process," indicate that the distribution of hard and soft components in the individual high volatile coals and blends of coals may be quantitatively interrelated to coke stability through selected ranges of coal volatile matter. The objective of this progress report is 1) to demonstrate the statistical relationships which exist between coal grindability and the numerous coal petrographic entities and 2) to present the results of initial studies concerning the correlation of the coke physical strength index of stability with coal volatile matter and grindability.

Jan 3, 1964

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters – usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

Contents

Jan 1, 1985

Grinding and Beneficiation Characteristics of a Low-Grade Haematite Ore

Sep 13, 2010