Search Documents

By Edward D. Elkins

CalMat Co. is one of the largest producers of construction aggregates in the United States. The CalMat Reliance plant is located in Irwindale, California, and is situated on an alluvial fan formed by the San Gabriel River. The fan deposits are of Quaternary age and were derived from granitic and metamorphic bedrock exposed in the San Gabriel Mountains to the north. The sediments are poorly sorted and range in size from large boulders to clay size particles. The coarse material is hard and durable and consists of quartz diorite, granodiorite, granitic gneiss, schist and minor amounts of volcanic rock. The matrix is comprised of silty sand with varying amounts of clay. Thin silt and clay lenses occur sporadically throughout the deposit. The clay content of the matrix and the degree of weathering of the coarse material increases with depth. Based on seismic data, the alluvial fan varies from 200 to 400 feet thick and overlies crystalline bedrock. The Reliance plant was constructed in 1971 and 1972. It has a nominal capacity of 1200 to 1400 tons per hour, and typically produces more than three million tons of aggregate products per year. Alluvial fan sediments are mined from a gravel pit situated adjacent to the plant. The material is fed through a mobile, 48- by 60-inch, in-pit jaw crusher, then transported by conveyor to the main plant to be processed. The plant is modern and highly efficient. It has a typical wet and dry circuit and is capable of producing a wide range of aggregate products. To extend the life of the plant, a 9,000 foot conveyor system is being constructed to connect it to a granite quarry operated by Azusa Rock Inc. The quarry is located north of Irwindale, and is 50 percent owned by CalMat Co. The conveyor will be used to export crushed rock from the quarry to Reliance. The existing plant will be modified to process the crushed rock.

Jan 1, 1995

By Z S Chang, T F. Zhou, G X. Zhong

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Yaojialing zinc-gold polymetallic deposit is a newly discovered, large skarn deposit in the Middle-Lower Yangtze metallogenic belt, East China. It is located in the transitional zone between the Tongling uplift block and the Fanchang faulted basin. It is mainly hosted in the contact zone between early Cretaceous granodiorite porphyry and Carboniferous-Triassic limestone, or occurs in limestone xenoliths within the intrusion. Skarn and stratabound massive sulfide orebodies are the primary ore styles. Sulfide ?34SV-CDT values indicate a magmatic sulfur source, in common with most deposits in the Tongling block. Calcite d13CV-PDB and d18OV-SMOW ratios reveal that marine carbonates were the major source of carbon in late-stage hydrothermal fluids. The calcite probably formed during interaction between magmatic fluids and carbonate wall rock.CITATION:Zhong, G X, Zhou, T F and Chang, Z S, 2015. Geology, chronology and isotope geochemistry of the Yaojialing zinc-gold deposit, Tongling ore district, Anhui Province, China, in Proceedings PACRIM 2015 Congress, pp 457–462 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Johan K. Rodenburg

A major bauxite belt was discovered and evaluated from 1969 to 1974 by P. T. Alcoa Minerals of Indonesia in West Kalimantan, Indonesia. The proven reserves of beneficiated bauxite are 800 million tons averaging 38.6% AA1203 and 3.0% RSiO2. Inferred reserves of washed bauxite are in excess of 2 billion tons. The bauxite occurs as capping of low lying hills which were formed during the post Paleogene peneplaination stage. The overburden varies from 0.6 to 3.8 meters and the nodular bauxite horizon from 2.2 to 5.2 meters. The deposits were formed by the in situ weathering of predominantly acidic and basic intrusive rocks.

Jan 1, 1984

By Howard Brown

High purity, high brightness limestone deposits in the San Bernardino Mountains and Mojave Desert region occur in upper Paleozoic carbonate rocks which are part of an upper Precambrian and Paleozoic sequence that unconformably overlies crystalline basement. The Paleozoic strata are divided into formations and members, and correlated with strata of the inner Cordilleran miogeocline. The region has been affected by multiple Mesozoic intrusive, contact, and regional metamorphic events. Structure is complex, and includes polyphase Mesozoic folding and thrusting, and complex Cenozoic structures. The area continues to be seismically active. High brightness (white), high purity crystalline limestone deposits are uncommon because their formation is dependent on several geologic processes which include; 1) depositional environment, 2) contact and or regional metamorphism, 3) folding and faulting, 4) uplift and erosion, and 5) preservation through geologic time. The complex geologic history of the San Bernardino Mountains and Mojave Desert region has allowed the formation of several large high brightness, high purity limestone deposits which are currently being mined or will be mined in the future. Specialty Minerals, Inc. (formerly Ptizer), Pluess-Staufer (California), Inc. and Partins Limestone, Inc. produce high brightness, high purity limestone from several quarries in the San Bernardino Mountains. These active mines combined with undeveloped deposits controlled by Pluess-Staufer in the San Bernardino Mountains, New York Mountains, and Bristol Mountains in the Mojave area, contain proven and or indicated reserves sufficient to sustain production through the 21st century Detailed geologic mapping, intimate knowledge of stratigraphy, recognition of complex structures, sampling, drilling and assay data, are proven tools in the discovery and delineation of high brightness, high purity limestone deposits in the San Bernardino Mountains and Mojave Desert region of southern California.

Jan 1, 1995

By H. J. Brown

Pluess-Staufer (California) Inc. Lucerne Valley California operation is one of the largest producers of high brightness high purity fme grind limestone products in western North America. The San Bernardino Mountains area of southern California contains the largest high brightness, high purity limestone mining operations and undeveloped reserves in western North America (Fig. 1, Brown 1987). Combined annual production of high brightness limestone products from several operations is approximately 1.5 million tons, with an estimated gross value of $75 million dollars per year (Fig. 2). An additional 5.0 million tons of cement grade limestone is mined by several large cement producers in the nearby Mojave area (Brown, in press). The purpose of this paper is to summarize the geologic setting, genesis and mining of white, high purity crystalline limestone by Pluess-Staufer (California) Inc.

Jan 1, 1994

By AMIRA P588 Research Team

This contribution summarises new knowledge and data, obtained during a three year ARCAMIRA funded research project, on the mineralogical and geochemical characteristics of hydrothermal alteration associated with low sulfidation, gold-silver epithermal deposits. These data are used to develop exploration vectors for use at both deposit and district scales, plus techniques have been established to distinguish ore grade epithermal systems from barren or low grade systems. Deposits investigated were Ladolam, Papua New Guinea, Gosowong and Mt Muro, Indonesia, Cerro Vaguardia, Argentina and Bimurra and Twin Hills, Australia.

Jan 1, 2005

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By Xuanxue Mo, Zengqian Hou

"Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcanogenic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and backarc spreading during its evolution and formed a complete trench-are-basin system, i.e., the Ganzilitang suture zone, forearc basin, outer are, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate faultbound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.All VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is twofold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. All deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asymmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe.The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerals (Groups I and informed during intensifying stages of hydrothermal activity, and the majority of semi-yellow-ore minerals (Group III) formed during a thermal maximum. There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kurokotype VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By G B. Arehart

The Midas epithermal system is one of the larger low-sulfidation epithermal vein systems discovered in the western US in recent years, containing in excess of 3 Moz of gold (premining). The deposit is spatially and temporally related to bimodal volcanism in the Northern Nevada Rift; dates on igneous rocks (16 - 14.7 Ma) bracket the age of high grade veins (15.3 Ma). Hydrothermal alteration at Midas is typical of epithermal systems, comprising proximal potassic through distal propylitic assemblages; in contrast to many epithermal systems, Midas has minimal development of wallrock illite/sericite. Mineral assemblages are clearly zoned on the vein structures that acted as focal planes for fluid upflow. Geochemical zoning patterns also show this zoning. Metals were deposited in open-space veins as the result of boiling of hydrothermal fluids; multiple episodes of crustiform mineral deposition are documented in the vein textures. The major vein minerals include quartz, adularia, calcite, selenides and sulfides, with electrum as the primary ore mineral. REE patterns for vein material are similar to patterns for coeval rhyolites, but distinctly different from patterns of the host rocks. Stable isotope data are consistent with meteoric water as the dominant ore fluid. Combined REE and stable isotope data suggest that fluid from which the main ore-bearing stage of the veins was deposited was slightly lower pH than other stages.

Jan 1, 2005

By A. Gauthier, J .. E. Muir, M. Cormier

Falconbridge's Lac Shortt gold deposit is located in Gand Township, some 25 km north-east of Desmaraisville, The deposit was outlined in i980 by a drilling program me conducted by Falconbridge Ltd. in a joint venture with Corporation Falconbridge Copper after three years of systematic exploration by Falconbridge Ltd. in the Desmaraisville area. The gold bearing structure had previously been drilled by three other exploration companies. As based on an underground development programme conducted by Corporation Falconbridge Copper, the "in-si tu" mineral inventory to a depth of 500 metres at a cut-off grade of 3.0 g/t is estimated at 1 937 605 tonnes at a grade of 6.4 g/t (uncut) and 6.0 g/t (cut). Regionally, the stratigraphy consists of thick sequences of volcanic and volcanosedimentary rocks intruded by numerous and voluminous mafic (gabbro), felsic (granodiorite, syenite) and anorthositic intrusions. Structurally, at least two fold sets and one major fault system (E-NE) are present. Minor fault systems oriented E-NE and N-NW also occur. Mine stratigraphy can be divided into 1) - the hangingwall; 2) - ore zone; 3) - footwall. Hanging wall rocks include: a) green lapilli and blocky tuff b) transition zone c) green mica crystal tuff and d) red dolomitic tuff. Ore zone rocks include: a) bleached mafic tuff b) barren carbonates, c) pyritic dolomitic tuff (?) and d) brick-red syenite. Footwall rocks include: a) magnetic lava (so-called diorite), b) mafic lapilli and blocky tuff and c) alkali basalt, Native gold is the only gold mineral so far identified and it occurs both as free grains in gangue and as micro-inclusions in pyrite. Two geochemical groups were identified in the main rock units: 1) Alkali-rich rocks cons is ting of the ore zone and foot wall rocks and 2) Subalkaline group consisting of the hanging wall rocks. Ore analysis also shows Ba, Sr, W, Zr, REE and F enrichment in the ore zone. Footwall rocks are enriched in Na20. Present geological and geochemical data do not permit a clear interpretation of the formation for the Lac Shortt gold deposit but suggest it is a volcanic-hosted stratabound type. The bulk of the mineralization is associated with an exhalative phase following alkalic, carbonic, hydrothermal activity and part of the mineralization is associated with a late intrusive phase.

Jan 1, 1984

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Abstract-Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is confined by tectonic shear zones between marble and metapelites, extending laterally into the marble as tabular, pod or lenticular oreshoots (up to 50 m ?? 20 m ?? 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical profiles across mineralized zones confirm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the insitu supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly influenced by seasonal fluctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent flooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2 ~10-3.8 to 10-1.4) and oxygenated (fO2 ~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sulfides and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+ was transported into karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2 in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2 increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is con-?ned by tectonic shear zones between marble and metapelites, extending laterally into the marble astabular, pod or lenticular oreshoots (up to 50 m x 20 m x 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical pro?les across mineralized zones con?rm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the in-situ supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly in?uenced by seasonal ?uctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent ?ooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2~10-3.8 to 10-1.4) and oxygenated (fO2~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sul?des and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+was transportedinto karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By Jr. Ensign C. O., J. W. Trammell

The two principal methods of room-and-pillar mining practiced at White Pine make it important to predict variations in the thickness and rock types of a stratum called the upper sandstone. In full column mining, the nearly barren upper sandstone occurs between two ore horizons (called upper shale and parting shale, respectively), and is mined as a part of the ore column. In general, full column mining is not practiced where excessive upper sandstone thickness causes full column ore grade to be substantially lower than parting shale ore. In parting shale mining, the upper sandstone forms the mine roof. Difficulty in predicting upper sandstone character arose because the extent and directions of its variations were not apparent in the property's diamond drilling, in which holes are spaced on 1000-ft centers. A study of sedimentary features, undertaken to improve the predictability of trends in the upper sandstone, led to an interpretation of the sedimentary environment in which the sandstone was deposited. Ripple marks, mud cracks, and cross-bedding, as well as other, less well known features, such as channel casts, flute casts, and current crescent casts, were mapped or recorded. These data, coupled with the knowledge of regional facies changes gained from studying drill core, show that the upper sandstone was deposited by a series of streams flowing northeastward over the underlying parting shale. Deposition of the lowermost bed of the upper sandstone, near the ancient shoreline, was locally preceded by erosion of the parting shale, and the greatest thicknesses of sandstone are found in channels scoured out of the parting shale. Awareness of the rather strong linear trends in the upper sandstone makes it possible to project continuous areas of thick upper sandstone through apparently isolated "highs" in the upper sandstone thickness contour map, which is based on drill-hole information. Since local exceptions to general stratigraphic trends exist, a method was also needed for esti- mating, in detail, the thickness and degree of shali-ness of upper sandstone forming the roof in active parting shale mining areas. Because locally the parting shale was thinned by erosion during the deposition of upper sandstone, parting shale thickness is inversely proportional to upper sandstone thickness. Utilizing information taken from short drill holes into the roof, curves were constructed for the correlation of parting shale thickness (measurable in the mine) with the upper sandstone total thickness, as well as the thickness of its basal member. The White Pine mine is situated in Ontonagon County, approximately 6 miles south of Lake Superior, in the Upper Peninsula of Michigan (Fig. 1). The orebody mined by White Pine Copper Co. occurs in the lowermost 20 to 25 ft of the Nonesuch formation, a series of middle- to upper-Keweenawan shales, siltstones, and sandstones. This paper discusses the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the orebody. THE OREBODY AND MINING TYPES A brief description of the orebody and mining methods is necessary to show how the upper sandstone affects mine planning and grade control. In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions, as shown in Fig. 2. Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 2. Other authors1'3 have dealt in detail with the stratigraphy and mineralogy of the orebody. However, in this article, we are concerned with the major subdivisions only, and it will suffice to note the low copper content of the upper sandstone, shown in Fig. 2. At present, two types of room-and-pillar openings are created in the orebody. In one type, called parting

Jan 1, 1964

By W. V. Swarzenski

In its effort to combat waterlogging and soil salinity, the Water and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling andwater sampling since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline groundwater zones in the Punjab Plain. Fresh groundwater containing generally less than 500 ppm of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh groundwater extends to depths of 1500 ft and more. Saline groundwater occurs down gradient from sources of recharge, particularly in the lower central parts of the interfluvial areas, and presumably underlies most of the Punjab Plain. The groundwaters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters near sources of recharge to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in the Dera Ismail Khan District, sodium sulfate waters predominate. The pattern of distribution of saline groundwater zones and the observed gradual increase in mineral content, down gradient from sources of recharge, can be explained best by a hypothesis stressing the process of evaporation from the water table and solution of minerals within the alluvial aquifer. In 1954, detailed groundwater surveys in the Punjab Plain were initiated by WASID, the Water and Soils Investigation Division of West Pakistan's Water and Power Development Authority. The investigations, undertaken under a cooperative agreement between the governments of Pakistan and the United States, were aimed at the formulation of reclamation measures to improve waterlogged and saline soils, and to assess the groundwater potential of the Punjab and other areas of West Pakistan. The nature and urgency of WASID's primary task limited the exploration of the alluvial aquifer generally to its uppermost part. About 1030 test holes drilled in 47,000 sq miles of the Punjab defined the nature of the alluvium to depths of about 600 ft and yielded data on water quality to 400 or 500 ft. A report on the hydrology of the Punjab, based on the results of these investigations was published by WASID in 1963.' The present report incorporates data obtained by WASID since 1962 in a program of deep test drilling in the Punjab and the adjacent areas of Bahawalpur and Dera Ismail Khan District, permitting the definition of fresh and saline groundwater zones to depths of 1500 ft in some areas. Groundwater in the Punjab Plain is contained in alluvial deposits, predominantly sand and silt, which extend almost everywhere to depths of 1000 ft and more. The alluvium has been deposited by the Indus River and its tributaries since late Tertiary time and is contiguous with similar deposits in India. The Indo-Gangetic Plain extends from the foothills of the Himalayas to the ancient rocks of the Peninsular Shield in central India and to the ocean. Gradients are generally very low and range from about 1% ft per mile in the upper part of the plain to less than 1 ft per mile in the south and southwest. The monotony of the alluvial plain is broken by scattered bedrock outcrops in two of the interfluvial areas, Chaj Doab and Rechna Doab. The bedrock hills are projections of the northwest-trending Delhi-Shahpur Ridge that is largely buried by alluvium. The rocks of the buried ridge, presumably of Precambrian age, are essentially impermeable and define the lower limit of the alluvial aquifer in parts of Chaj, Rechna, and Bari doabs. Elsewhere in the Punjab, there are no outcrops of other consolidated rocks and their presence below the alluvium is conjectural. The principal areas of bedrock outcrops, near Kirana and Sangla, are shown diagrammatically in Fig. 1. The movement of groundwater through the alluvial aquifer of the Punjab has been described by Green-man and others.' In most of the area, the pre-irriga-tion water table sloped from the rivers downstream and toward the central axes of the doabs, indicating that the rivers were sources of groundwater recharge. As a result of seepage from irrigation canals, water levels have risen as much as 90 ft. In 1960 they were within 5 to 15 ft of the land surface and above the

Jan 1, 1970

By W. C. Hayes

The site selected for the United States prototype pumped storage project of Union Electric CO. was Proffit Mountain, five miles from Taum Sauk, the highest point in Missouri. Factors influencing final location were: high local relief; satisfactory rock type and structure; and an economic location in respect to existing transmission systems. The upper reservoir was constructed by excavating rhyolite porphyry from the crest of Proffit Mountain and constructing a rock fill dike encircling the area to form a 4350-acre foot reservoir. A 6564-ft tunnel connects the upper reservoir with the generating and pumping facilities. A concrete gravity dam on the East Fork of the Black River forms the 6350-acre foot lower reservoir. Precambrian rhyolite porphyry forms the crest of Proffit Mountain and the floor of the upper reservoir. The tunnel was excavated in rhyolite prophpy, granite porphyry, dolomite, shales and conglomerate. Abutments and the foundation of the gravity dam are in rhyolite porphyry, and much of the valley floor of the lower reservoir is underlain by dolomite and shale. Core drilling provided data on soundness of rock type, structure, depth of weathered zone and potential water loss in the fractured igneous rocks. After a six-year study of pumped storage and cost comparison with alternate stream generating units, the Taum Sauk pumped storage project was authorized by Union Electric Co. on Dec. 11, 1959.' The site selected is located in the St. Francois Mountains of southeast Missouri approximately 90 miles south of St. Louis (Fig. 1). The lower reservoir was provided by damming the East Fork of the Black River, a small tributary of the Black River with a minimum flow of about 1 sec ft. Construction of the upper reservoir was effected by quarrying the crest of Proffit Mountain - five miles from Taum Sauk Mountain, the highest point in Missouri — to provide material for a rock fill dike surrounding the quarried area. This provided a 55-acre mountain top lake with a water depth of 92 ft (Fig. 2). A vertical shaft and tunnel connect the upper and lower reservoirs through the two reversible pump-turbine motor-generator units operating under 800 ft of hydraulic head (Fig. 3). The output rating of the plant is 350,000 kw with daytime generation of about 2.2 million kw-hr under normal use. Night pumping will replenish water to the upper reservoir in about 91/2 hours3. The automatic operation is remotely controlled from the Osage plant and from the dispatchers office in St. Louis. GENERAL GEOLOGY Mountains of the St. Francois area consist of Precambrian granites, granite porphyries, extrusive fel-sites and basic dikes. Basal conglomerates overlain by Upper Cambrian Bonneterre dolomites and shales onlap the exhumed Precambrian knobs and hills and are exposed in the narrow valleys. Cambrian and Ordovician residuum as much as 200 ft thick is present on the slopes of many hills. Proffit Mountain consists of rhyolite porphyry and granite porphyry. All excavation for the upper reservoir was in rhyolite porphyry, and the same rock is present under the Bonneterre at the plant site and under alluvium at the lower reservoir dam site. The region has been dissected to the stage of early maturity with only small upland flats remaining. Considerable local relief (a requisite for the project) approaches 1000 ft. Streams flowing across the Precambrian ridges have formed restricted narrows, termed shut-ins. A shut-in approximately two miles downstream from the plant site provides an excellent site for the lower reservoir dam. TEST BORINGS Preliminary to final approval of the project, 12 test borings were made to determine subsurface geologic conditions (Fig. 2). Drill hole No. 12 at the lower reservoir dam site showed 20 ft of alluvium over solid rhyolite porphyry. Drill holes No. 1, 2 and 3 were drilled in the tail race area to depths of 66 ft, 75 ft and 95 ft respectively, and all bottomed in Bonneterre. Drill hole No. 4 at the plant site provided NX core to a total depth of 98 ft in Bonneterre. Drill

Jan 1, 1965

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

By W. C. Lacy

Urban development in semi-arid portions of the Southwest has upset a natural balance of geological conditions resulting in broad-scale and local subsidence or heaving ground conditions, Subsidence can be traced to two general causes: irrigation of reclaimed desert lands that have dry, low-density soils; and depression of the water table by ground water withdrawal. Accumulation of weathered volcanic tuff produces areas with swelling characteristics. Soil and subsidence studies made in the Tucson area in Arizona illustrate foundation problems typical of the Southwest that must be considered in the design of building codes. Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the arid to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area, prompted by foundation failures and breaking of buried service lines, serves to illustrate some of these relationships between the geological environment and history and engineering problems. ENVIRONMENT The desert region of the Southwest is characterized by isolated mountain ranges rising abruptly from low valleys or plains — the ranges generally occupy less area than do the intervening valleys. In southern Arizona the valley floors step up from near sea level to 2000 ft or more in elevation, and the ranges may rise to over 7000 ft. Desert and steppe-type climates predominate — climate is controlled more by elevation than it is by latitude. Both climate types are characterized by a lack of precipitation, the former more so than the latter. Practically all the rain that falls in the region evaporates; runoff or recharge generally occurs only during the wettest period. Water table levels are generally being depressed. Vegetation is restricted and consists mainly of creosote bush, cacti and sage brush on the deserts, and mesquite, pinon juniper and various types of grass on the steppes. Precipitation varies from about 3 in. on the warm deserts to about 12 in. on the steppes. Most of this falls in the summer or winter, with only rare storms in other seasons. Summer thunderstorms, often accompanied by hail, bring cloudbursts which send torrents of water streaming down the mountains onto

Jan 1, 1964

By F. W. Osterwald, C. R. Dunrud

Coal mine bumps are a serious hazard to life and property in the mines of east-central Utah. Research into geologic factors associated with these bumps indicates that the bumps are spatially and genetically related to structural and stratigraphic features. Some bumps are directly related to stress accumulation along faults, either from natural causes or as a result of mining. Frictional properties of bedding planes between coal and roof rock, and between some rock units within the roof, directly affect the deformation of coal ribs, and hence the incidence of bumps. These frictional properties are related to the lithology of the roof rocks as well as to the sedimentary structures within the rocks. Commonly a sequence consisting of 1/3 ft of carbonaceous silt-stone, about 2/3 ft of rider coal, and several ft of massive siltstone or sandstone overlies the main seam. The sequence causes difficult roof conditions in the mines, difficult mining conditions and, directly or indirectly, many bumps. The U. S. Geological Survey has studied the relationships between geological features and coal mine bumps at Sunnyside, Utah, for about six years. The work, which was originally undertaken at the request of and in cooperation with the U.S. Bureau of

Jan 1, 1965

By D. M. Milne, R. F. Stoner, W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of fresh water whose origin can be traced to the present and historical courses of the River Indus. In the past, the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water table has risen to within a few feet of the surface. The river system itself is being progressively devel-oped for irrigation and very shortly a situation will arise where the entire low winter flow will be utilized. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilize the water table at safe depths. This paper discusses some of the methods used to ensure optimum economic development of the fresh groundwater and describes the general design philosophy evolved by the authors' firms for both irrigation and drainage wells, with respect to both well configuration and operation. Water quality standards are discussed insofar as they affect subsequent use of the groundwater. A few particular aspects are considered, including the values of the relevant aquifer constants, the construction of wells, and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to produce fresh water from layers overlying saline water. This solution is also discussed. The recent interest in the groundwater of the Lower Indus Plains of West Pakistan has two main aspects. Firstly, soil waterlogging and the associated salinity hazards caused by rising water tables are a serious problem in agriculture, and the ease with which drainage requirements can be met by aquifer pumping makes this an obvious solution. The second interest stems from the rapid intensification of irrigation agriculture and the growing shortage of water supplies. In the areas where the groundwater is of suitable quality it can be used immediately for irrigation at relatively small cost and with large financial returns. In addition, the aquifer forms a potential storage reservoir which could be recharged from high river flows and depleted by pumping at times of scarcity. SOURCE OF GROUNDWATER The Lower Indus plain is a relatively long and narrow alluvial basin on a north-south axis, some 23,000 sq miles in area, bounded by higher land to the east and west. One hypothesis to explain the distribution and quality of groundwater in the region1 presupposes a river system considerably larger than, but very similar to the present river. This is characterized by a single mainstream, with subsidiary overspill channels in times of flood, running along the crest of a self-deposited ridge and with an extensive advancing delta. Sea water is contained in the alluvial pores of the advancing delta, forming the native groundwater. This has been partially displaced from two sources, namely direct seepage of fresh water from the river channel in meander flood plain areas and percolation from flood spillage in cover flood plain areas. Percolation has been subject to much re-evaporation and is thus slightly saline even as it reaches the groundwater. The whole complex has been further affected by two main influences: evapotranspiration from the land surface that tends to salinize the groundwater and down-valley flow that tends to bring fresher water

Jan 1, 1970

By R. C. Hepworth

Heaving in roads built on the Mancos Shale is a serious problem in east-central Utah. Heaves are expressed as local bumps, general rises and severe cracking of the pavement. The heaves usually occur in shale road cuts and generally show a seasonal cycle, which reaches a maximum development in the winter. The presence of certain salts, absorption of moisture and physical properties of the subgrade materials were considered, in Utah, to be the main factors in the heaving mechanism. Work done on similar problems elsewhere and studies conducted by the author indicate that the latter two factors are the most important. Results of this investigation indicate that heaving areas are associated with slaking shale or expansive clays, with and without salts present. Laboratory studies show that the initial moisture content of remolded samples and the desiccation history of un- disturbed samples have a major effect on swelling. Swell tests on compacted samples at various temperatures indicate that water has more influence on swell than temperature, except for samples containing sodium sulphate, which swelled with decreasing temperature. Chloride salts inhibited swelling. Tests on shale cores indicate that the stability of slaking shale can be preserved by maintaining its original moisture content. It is concluded that shales and expansive clays, when exposed in road cuts, become desiccated and are subject to expansion when moisture is subsequently available. The seasonal cycle of heaving may possibly be explained by the annual moisture excess and deficiency. To minimize the problem, freshly exposed shale should be kept wet, and the thickness of the subbase and base courses should be increased. The Utah State Department of Highways has been plagued for many years with a distressed condition that develops in roads constructed on the Mancos Shale. Locally these distressed areas are known as heaves, frost boils and alkali boils. These names refer to the surface expression, time of year

Jan 1, 1965