Search Documents

By Y Zhang, X Yi, J Deng, J Zhao, J Song

To obtain the combustion process of a coal fire, a high-temperature programmed system is used to simulate the spontaneous combustion process of fresh and weathered coals. Both fresh coal and weathered coals from Liulingou, Inner Mongolia, China, were used to examine the gas releases from constant temperature to 650°C. Moreover, gas release rate was used to calculate the characteristic temperatures. The results showed the coal samples lasted to oxidise under high temperatures, and released plenty of heat to assist self-heating. The humic acid contained inside the weathered coal went through thermal decomposition as temperature rising and generated gases. This resulted in increasing concentrations of CO, CO2, CH4, C2H4, and C2H6. Changes of CH4, C2H4, and C2H6 gases were also similar. For weathered coal, concentrations of three gases were kept in balance under low temperatures, increased rapidly with the temperature rising. After the ignition temperature, the concentration of hydrocarbon was reduced. In addition, particle size affected coal spontaneous combustion. Coal samples with less than 0.9 mm in size produced much more CO than others. This study has examined coal spontaneous combustion caused by coal weathering during mining and its impacts on self-heating and pyrolysis in the process.CITATION:Deng, J, Song, J, Zhao, J, Zhang, Y, Yi, X and Zhang, Y, 2017. Gaseous products of weathered coal during the process of spontaneous combustion, in Proceedings Australian Mine Vent Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Baojun Zhao

Primary lead production using the lead blast furnace in conventional practice is carried out using sinter feed. At YMG, China, the sinter plant has been replaced with a lead ISASMELT furnace. The ISASMELT furnace produces lead bullion plus a high-lead slag, which is cast into lumps to provide a suitable feed for the blast furnace. In the present study the relative microstructures and reduction characteristics of industrial lead sinters and synthetic ISASMELT slag in CO/CO2 gas mixtures have been measured and compared. The microstructure and property changes, and the mechanisms of reduction in each case are examined and discussed. The results of the study are used to explain the successful implementation of cast slag feed in commercial ISASMELT- lead blast furnace practice. Key words: lead slag, lead sinter, lead blast furnace, reduction kinetics and mechanisms

Jan 1, 2008

By T. A. Larssen

The efficiency in production of manganese ferroalloys is dependent on the gaseous reduction of the higher manganese oxides in the ores used as raw materials. The materials, descending in the furnace, will meet the furnace gas that contains significant amounts of CO(g) and reduce in subsequent steps, the last step being reduction of Mn3O4 to MnO. This step may to varying extent occur at temperatures exceeding 800 °C, i.e. in the active region of the Boudouard reaction. The gas reduction of Assmang and Comilog manganese ores were investigated in CO-CO2-atmosphere at temperatures up to 1000 °C. It was seen that decreasing ore size correlates to a lower reduction temperature and increasing reduction rate. Similar effect was observed with increasing CO-content in the gas atmosphere. Further, it was found that Comilog ore obtained a complete prereduction at 600 °C, whereas reduction of Assmang ore was not complete at 800 °C for the majority of the experiments.

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge.. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By Meliton M. Garcia, Satya Harpalani

The volume of gases produced in major and trace amounts as a result of detonation of explosives in an underground mine was determined. The volumes of major gases (CO, CO2, NO and N02) were measured immediately following detonation, during the mucking operation, and following the removal of muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The composition of the gases produced varied significantly depending on the composition of the explosive/blasting agent. An average of 95% of the gases produced were found in the test chamber immediately following the detonation, while 2% was found in the chamber following the removal of the muck. Several compounds were identified in trace amounts. Of particular interest was the detection of benzene, toluene, butenes, ethyl benzene and naphthalene since exposure to some of these compounds, even in trace amounts, could present a serious health hazard.

Jan 1, 1987

By O. W. Ellis

THE writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.1 The copper referred to in his in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal, did not measure up to conductivity FIG. L -INGOT OF OVERPOLEP COPPER. standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the Westinghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 ½ in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of overpoling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By Paul D. Merica

DURING the Dark Ages, when metallurgy was practiced by the alchemists, any unusual or disturbing variation in metallurgical operations was ascribed to the, presence, in the metals or ores, of an evil spirit, and it was necessary to exorcise and drive it out "by suitable incantations. In this day of science and of engineering, things still incomprehensibly go wrong in the metallurgist's work shop. The metallurgist is even now not unwilling to lay the blame for many such experiences at the door of something which intellectually- much resembles an evil spirit, "gas in the metal." The presence of gases in his metal, he knows, occasions him many very definite troubles which he can clearly distinguish and diagnose-why may it not be also responsible for those which he cannot so well understand?

Jan 1, 1931

By AIME AIME

ON Thursday a most interesting symposium on "Gases in Metals" was held, with both morning and afternoon sessions. The morning was devoted principally to the considerations of the steel maker, the nonferrous field being taken up in the afternoon period. Dr. John Johnston, as chairman, introduced the subject with "A Short Analysis of the Gas-metal Problem and Its Practical Importance." He then introduced P. H. Brace who explained in considerable detail the various vacuum fusion and other methods in use at present, both here and abroad, in the study of "gases" in metals. He was fol¬lowed immediately by H. W. Graham on "The Effect of Oxygen in Steel." The papers elicited considerable discussion, the point being particularly noted by both Dr. Rawdon and Dr. Sauveur that a knowledge of "total oxygen" alone is not sufficient information for the metallurgist, distribution of oxygen being probably the more important. Dr. Johnston, in commenting on the lack of agreement among many of the methods now in use, such as the Ledebur and vacuum fusion, spoke of the contemplated plan of the Iron and Steel Division to have a number of standard samples analyzed by many laboratories by the various methods, the Bureau of Standards acting as a clearing house, so that more definite information may be obtained on the comparative accuracy of the method.

Jan 1, 1933

By AIME AIME

THE joint symposium on gases in metals on Tuesday: Feb. 16, between the Iron and Steel and the Institute of Metals divisions opened the technical sessions for both of these bodies. After a few words of introduction by P. D. Merica, R. S. Dean presented a paper by V. H: Gottshalk and himself on the solubility of gases in metals.

Jan 1, 1932

By D. Harrington

When the word "gas"' is mentioned in connection with mining almost invariably it is inferred that the explosive gas, methane, is in mind and that the reference is to coal mining. Although methane is likely to occur in any coal mine the metal mines of the world contain by far a greater variety of gases than do the coal mines. Often the gases in metal mines are as dangerous as the gases likely to be found in coal mines, and sometimes are even more deadly. A coal mine is more likely to contain methane than a metal mine. In rare instances it may contain high percentages of nitrogen or carbon dioxide or it may be deficient in oxygen where the air is confined in a blind end or in a sealed region. Much more rarely relatively small percentages of ethane or other hydrocarbons with an odor of ether, gasoline, or kerosene, or minute percentages of hydrogen sulphide are found in a coal mine. During a coal-mine fire or explosion carbon monoxide content is likely to be high (4 per cent or more), and if the coal contains much sulphur the high fumes may contain some sulphur dioxide.

Jan 1, 1931

By D. Harrington

WHEN the word gas is mentioned in connection with mining, almost invariably it is inferred that the explosive gas, methane, is in mind and that it must refer to coal mining. While it is true that methane occurs, or is likely to occur, in almost any or all coal mines, it is also a fact that the metal mines of the world have in them by far a greater variety of gases than have the coal mines. In many cases the gases in metal mines are as dangerous to individuals as the gases likely to be found in coal mines; in some instances the metal mine gases are even more deadly. The coal mine is more likely to have methane than the metal mine, in rare instances it may have high percentages of nitrogen or high carbon dioxide, or there may be a deficiency of oxygen where the air is confined in a blind end or in a sealed region; much more rarely there are found in coal mines in relatively small percentages, ethane, or other hydrocarbons with odor of ether, gasoline or kerosene, or there may be minute percentages of hydrogen sulfide. In time of coal mine fire or explosion, there is likely to be high carbon monoxide (4 per cent. or over in some cases) and if the coal contains much sulfur, there may be some sulfur dioxide in the fire fumes. In metal mines there are a number of cases of occurrence of methane and attendant explosions; some metal mines have appreciable percentages of the decidedly explosive hydrogen; in some metal-mining regions carbon dioxide flows into the mine, fills the workings and overflows just like water. In other regions, at many working faces there are high-temperature gases containing a mixture of gases of sulfur (sulfur dioxide, hydrogen sulfide and possibly SO3 in some cases) together with carbon dioxide and nitrogen, and the deadly hydrogen sulfide in lethal proportions is found in some high-sulfide metal mines at blasting time. Carbon monoxide constitutes a decidedly dangerous day by day hazard in connection with metal-mine blasting, because of the heavy charges of dynamite that are used and the use of fuse, which in burning gives off much carbon monoxide. The poisonous gas hazard is accentuated because of the relatively small openings where metal-mine blasting is done and to the inefficient ventilation of the usual metal mine.

Jan 1, 1930

By Raymond C. Johnson

GASIFICATION is important to the anthracite industry, as it is to the entire solid-fuel industry and to the nation. However, to the anthracite industry it may have particular significance in that it would increase the market value of many millions of tons of a by-product fuel, which the industry now has in storage and is currently producing, in addition to increasing the potential market for all its products. The by-product fuel is of usable quality but the ash content is higher than it can be in other products and therefore it must be converted or used at the point of production. Gasification is one method by which the product may be given increased value. The inherent characteristics of anthracite make it well suited for producing a fuel or synthesis gas. It is the most concentrated form of natural commercial carbon, noncaking and noncoking; it does not produce smoke, tar, or soot and has a low sulphur content; and the volatile matter, which ranges between 2 and 8 pct, is 80 to 85 pct hydrogen with small amounts of methane, carbon dioxide, carbon monoxide, and nitrogen. The ash fuses at high temperatures, which allows it to be burned at high rates without slagging. However, with the addition of small amounts of dolomite, the ash will form a slag, or glass, which is very fluid. Anthracite has long been used in the manufacture of city gas and it is extensively used in various parts of the country to make water gas to be converted to hydrogen. Buckwheat and rice anthracite are used in Galusha producers to make producer gas. Excellent synthesis gas has been made in a Galusha producer with rice and barley anthracite with oxygen in tests at the Consolidated Mining and Smelting Co., Trail, British Columbia. In these tests, anthracite was shown to have advantages over competitive fuels, in that the gas had a higher hydrogen content and could be cleaned with less difficulty. The anthracite seams are steeply pitching and in mining the parting strata and some of the roof and bottom materials are taken with the coal. In preparation, these materials are separated by gravity from the commercial product and stored in refuse banks. This refuse contains a mixture of rock, slate, or shale, and high-ash anthracite with bone coal, which is low-ash coal that is interspersed with thin bands of shale. The bone coal contains between 25 and 50 pct ash with an average ash content of approximately 30 pct, with a

Jan 1, 1953

By J. E. Tobey

UNQUESTIONABLY, manufactured gas will stage a comeback of such huge proportions as to dwarf its previous history. Timing will depend on two things: the diminishing supply of natural gas and the perfecting of processes for large-scale production of high-Btu gas from, coal. What the timing will be, and how soon the new era will begin for manufactured gas, no one knows. It may be just around the corner and it may be several years, but it is certain to come. It will depend on economic changes, and any major world upheaval might accelerate it tremendously. Supplemental gas for pipelines will come no doubt from two sources at least: (1) synthetic-fuel plants of the coal-chemical group, which produce chemicals and liquid fuels with a tail gas high in methane as a by-product; and (2) large-scale gasification plants, which will produce high-Btu gas entirely or as a major product with chemicals and liquid fuels as by-products. There is important activity at the present time, in the development of new processes and the improvement of those now in existence. The first large-scale gasification plants of the second category probably will be strategically located in the coal fields on or near the long-distance transmission gas lines, and these plants probably will operate jointly with large natural gas storage fields. Inasmuch as virtually all the major gas-transmission lines cross one or more coal fields, such locations will not be difficult to find. It will be a practical necessity to produce a high-Btu gas -that is, 750 to 1000 Btu-in order to maintain the capacity of the main transmission lines and local city distribution systems and further to eliminate the problem of appliance changeovers in the cities. If gasification plants on a medium or smaller scale prove to be economical, local gas utilities no doubt will consider .the construction of such plants to supplement their supply of natural gas. If low-temperature distillation processes like those now being developed by the Pittsburgh Consolidation Coal Co. are successful, and there is reason to believe that they will be, utilities that supply both gas and electricity to communities would find this method particularly attractive, as they could burn the char product directly under power boilers, thereby minimizing thermal

Jan 1, 1953

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with law ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the site range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for various reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas-containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully

Jan 1, 1953

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with low ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the size range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for vari¬ous reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully.

Jan 1, 1953

By H. Ziock, J. Ruby, A. A. Johnson

Power generation systems that promote energy security and environmental benefits are highly desired and pursued by a number of government and industry programs. Gasification of coal, other fossil fuels, or biomass has the technical promise of high efficiency and low or zero emission. Gasification for the purpose of electrical power generation has been researched, developed and demonstrated over the last 20 years, but for many reasons is not viewed as economically competitive. This paper describes a coal-based gasification technology well suited to mid and long-term goals of secure, environmentally clean energy. The technology should be adaptable for use with other carbon-based fuels including biomass and a full range of fossil fuels. The new zero emission gasification process is sponsored by ZECA Corporation, a continuation of the Zero Emission Coal Alliance (ZECA). ZECA has completed process design and engineering to assess the viability of a concept originated at Los Alamos National Laboratory, and the creation of a business plan to define paths for advancing the technology toward a near-term goal pilot plant. The zero emission carbon (ZEC) technology includes hydrogasification, the production of hydrogen and the carbonation of lime with CO2. For the power generation base case, the hydrogen is used in high temperature coal compatible fuel cells to produce electricity and the carbonate is calcined to produce a pure stream of CO2for sequestration. This paper provides the status of work with the ZEC technology and the availability of crucial equipment, materials and required testing. Discussions are presented for future actions to accelerate the technology assessment, testing and demonstration of a ZEC plant. Brief remarks are provided on complementary projects dealing withCO2separation and gasification costs.

Jan 1, 2004

By Pieter van Nierop

Outline ? What is gasification? ? Gasification Technologies ? Gasification ?The early years ? Gasification ? The last decade ? The Alberta Situation ? The Importance of Gasification in Alberta ? Polygeneration ? Development ? Conclusion

May 1, 2004

By M Hino, Y Sasaki

Sustainable handling of municipal waste and sewage sludge has an important goal to recycle resources without supply of harmful substances to humans or the environment. The gasification mechanism of phosphorus from municipal waste and sewage sludge during the incineration process has been investigated to develop a phosphorus recovery system. Quadrupole mass spectrometer coupled to an electric furnace is applied to study the vaporisation behaviour of phosphorous gas phases from municipal solid waste (MSW) incinerator ash of sludge during solid-state reduction by carbon. Measurements are carried out in vacuum conditions of 2 x 10-6 Torrs and furnace temperature range 573 - 1773 K, at a heating rate of 7.22 K/minute. It has been found that most of the phosphorus is vaporised as PO2, P2 and P4, in agreement with thermodynamic estimation despite a shift in the temperature regimes.

Jan 1, 2006

By Wilhelm Flesch

THE object of development work in the field of gasification is to find a process by which all' fuels, regardless of their individual properties, can be gasified economically. This paper describes the development of the Winkler process. The economy of the gasification process depends not only on the degree of the gasification effect but also, to a decisive extent, on the costs of fuel, production, and installations. Fig 1 shows the relation between fuel costs and gasification efficiency for various types of fuels. Since the fuel cost in the gasification of coke amounts to two thirds of the price of gas, and the thermal unit in brown coal costs only one third of what it costs in coke, it is easily seen how profitably cheap fuels can be gasified, especially if these fuels require minimum preparation and gasification is done in the vicinity of the mines. These possibilities were a great advantage of the Winkler generators, which were installed 20 years ago in the central German brown-coal fields and, at that time, were without rival for the gasification of finely divided fuels. In the Winkler generator (Fig 2), crushed and ground solid fuels were, for the first time, successfully gasified with oxygen and steam on an industrial scale. Unlike the usual processes formerly employed on an industrial scale, this gasification, which proceeds continuously in the glowing, seething fuel bed, makes only extremely low demands on the fuel. The fuel no longer has to be in lumps and abrasion-resistant, but must be capable of reaction and must be fed into the generator in a grain size of 0 to 8 mm. Brown coal or bituminous coal, or their low-temperature cokes, can be gasified in the Winkler generator. Large plants using fuels are operating on an industrial scale in Europe and in Japan. Table 1 shows the results obtained by gasifying these, fuels in Winkler generators. The thermal efficiency of gasification, which is the relation between the calorific value obtained in the gas produced and that of the fuel consumed, gives no indication of the quantity of steam generated in gasification. The generation of steam in the waste-heat boiler of the Winkler generator adequately-covers the steam consumed in gasification. To obtain effective gasification in the Winkler process, combustible mate-

Jan 1, 1953