Search Documents

By Kush Patel

This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser.

Feb 1, 2020

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By Kimberley MacHardy, Ann Maest, Greg Lawson, James Kuipers

Although water quality predictions are often made in Environmental Impact Statements (EIS's) as part of the National Environmental Policy Act (NEPA), comparisons between predicted and actual water quality conditions are rarely reviewed. A comprehensive review of predicted and actual water quality conditions was conducted for a number of large U.S. hardrock mines with EIS’s. For mines with large differences between predicted and actual conditions, factors responsible for the deviations, such as characterization and modeling errors or engineering failures, were identified. Recommendations are made for how the NEPA process could be modified to better predict water quality at hardrock mine sites.

Jan 1, 2005

By A Gerson, S Miller, R Smart, J Thomas

Environmental Geochemistry International (EGi) and the Ian Wark Research Institute (IWRI) collaborated in a three-year Australian Minerals Industry Research Association (AMIRA) research project (Project Number P387A) focussed on the prediction and kinetic control of acid mine drainage. As part of this project, single addition, and sequential net acid generation (NAG) testing was carried out on sulfide mineral samples. The test samples comprised a range of synthetic waste materials prepared using a quartz bulk and controlled quantities of the commonly occurring sulfide minerals; pyrite (FeS2), pyrrhotite (Fe7S8), arsenopyrite (AsFeS), chalcopyrite (CuFeS2), chalcocite (Cu2S), covellite (CuS), bornite (Cu5FeS4), galena (PbS) and sphalerite (ZnS). NAG test results clearly show that there are significant differences between the acid forming potential of sulfide minerals. The NAG test results for each mineral were compared with theoretical acidity values (NAPP*). The NAPP* calculation was based on stoichiometric oxidation reactions assumed for each of the sulfide minerals. Sequential NAG values for pyrite corresponds closely to predicted NAPP* values, confirming the assumption that pyrite oxidation occurs according to the stoichiometry assumed. For the pyrite sample with 5 wt per cent S, two NAG stages were sufficient for all of the sulfur to be released to solution. Since sulfides in waste materials will generally be dominated by pyrite, results also confirm the validity of including NAG testing for ARD evaluation of most waste rock. NAG testing confirms that of the sulfide minerals examined, only pyrite, pyrrhotite, arsenopyrite and chalcopyrite are acid producing, ie able to produce leachate with a pH less than 4.5. In the case of sphalerite, galena, bornite, chalcocite and covellite the pH of the final NAG solution was greater than 4.5. The significant differences between the acid forming potential of different sulfide minerals could lead to overestimation of acid producing potentials based on NAPP values calculated from total per cent S alone, ie assuming all S is present as pyrite. The oxidation of galena during the NAG test resulted in the consumption of acid. The examination of the galena surface by X-ray photoelectron spectroscopy (XPS) after oxidation in peroxide solution indicated the presence of polysulfide. The reaction of sulfide to polysulfide is acid consuming, thus explaining the net acid consuming behaviour of galena in the NAG test. This reaction pathway may provide a possible explanation for the lower than expected acid production observed for some of the other sulfide minerals examined.

Jan 1, 2003

By F. Soumis

This paper describes an integrated procedure for the very short term production planning of an open pit and the execution of this plan: the truck dispatching. Integration of plan and dispatch means that the plan is realistic so that its objectives can be realized by the dispatch. This realism is obtained by supplying the plan optimization, which involves mixed integer programming, linear programming and non-linear programming, with experimental O.R. models of waiting and blending. The arrangement of these models in the computer programm has made it possible to obtain very short computing time for the planning in spite of the width of the optimisation. The dispatching of a truck is made by solving a classical assignment problem for each dispatch over a horizon of the expected*next 10-15 trucks to request dispatches. This deep-reaching dispatch procedure uses the continuously arriving information about trucks' positions and shovels situations and models by probability functions the expected waiting time of shovels and trucks. In this manner trucks and shovels are synchronized and last moments' opportunities for productivity gains can be obtained. The dispatch procedure takes .5 second on PDP11. This integrated planning and dispatch procedure gives high productivity while ensuring good blending. Results from the Mount Wright mine of the Quebec-Cartier Mining Co., where the integrated procedure has been installed on the existing computer equipment PDP11, are included.

Jan 1, 1989

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

Considering the risks involving the use of cyanide, other complexing agents have been evaluated for the treatment by electrodialysis of the effluent of brass electrodeposition and among them, EDTA is interesting since it has been already tested for many years to separate ions. The main objective of the present paper was to evaluate the occurrence of fouling and scaling on the surface of the anion-exchange membrane HDX 200 by the construction of chronopotentiometric curves and speciation diagrams in different conditions (pH between 10–12 and proportion of cupric ions of 30%, 50%, 70%). According to the results, the chronopotentiometric curves did not show additional inflexion points typical for the cases which occurs fouling and scaling for the pH values evaluated, which is in accordance with the speciation diagrams of the solutions constructed with the aid of Hydra-Medusa software. Hence, the pH and the proportion of cupric ions did not show influence on the curves behavior.

Mar 1, 2018

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Kenneth J. Reid, Marian S. Stachowicz

A preliminary evaluation of a new in-stream particle size analyzer has been carried out using materials obtained from a taconite plant in Northern Minnesota. Results are reported for bench scale, pilot scale and full scale tests, the latter being carried out in a taconite plant concentrator. The unit employs a novel scanning laser microscopy principle and details of the equipment configuration and operating principles are presented and discussed. Data acquisition is via an eight channel digital electronic system and particle counts are collected on the basis of reflected light pulse time intervals which are a direct measure of particle size. Output is available as an eight point individual or cumulative size distribution or as computed averages. The practical aspects of sample point location and flow requirements for reproducible results are outlined and discussed.

Jan 1, 1990

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By Gökçe Törenli, Okay Tutar

"Predicting the performance of plant-scale comminution circuits is essential to monitor the energy use and product size distribution, allowing us to control and optimize the whole process. In the light of this issue, with the assist of recent technologies, simulation techniques utilize the chance of putting the theory into practice in the most accurate way. For this purpose, this study aims to evaluate and optimize the efficiency of a plant-scale ball mill circuit by using perfect-mixing ball mill model on a simulation environment. The comminution circuit is selected from a specific copper-ore processing plant in Turkey. The essential parameters which are required for this study such as fresh feed Bond work index, size distribution etc. are determined by laboratory experiments. The forecasted data which are calculated by third-party software will be compared by the industrial operating data, in order to determine the performance of comminution circuit. In addition to that, this methodology provides a greater ability to analyse, optimize and understand the comminution circuit of ore treatment plant. The authors believe this work will provide supplementary data for further studies on simulation and subsequent optimization of comminution circuits.INTRODUCTION By the assist of mathematical models of the grinding mills and classifiers, simulation of the grinding circuits become more common in comminution because it is relatively economical and able to consider many variables simultaneously. It’s proceeds depends on the accuracy of the models and capability of reflect real operations. Computer-based simulation studies would provide the quantified information about the effects of the proposed changes on the comminution circuit performance in terms of size distribution, mass flow rates, equipment efficiency etc. Then the mentioned data used in order to check the suitability of the current equipment to the modified conditions, and for equipment selection. The outputs of circuit could also be used to estimate downstream flotation circuit performance because the general aim in this study is to The aim of the study is to investigate optimum operating variables and achieve p(80) size of 57 µm and 64 % of -36 µm particle in hydrocyclone overflow stream, which is optimum for that porphyritic copper ore for best concentrate recovery after flotation process in specific copper ore comminution circuit by using modelling and simulation techniques. Sampling survey was carried on the fine ore bin in order to perform Bond work index test and determine work index value (Wi). Thereafter mass balancing, using the size distribution data and tonnages, models for ball mills and hydrocyclone were developed. Finally, the circuit performance were investigated by computer simulations via JKSimMet software."

Jan 1, 2018

By Aydin Shaterpour Mamaghani, Bilgin. Nuh, Engin Dogan, Tayfun Erdogan

"Improved safety and more environmentally friendly operation are basic advantages of mechanical excavation over the drill and blast method. Raise Boring Machines (RBMs) are one of the types of these machines which have recently been increased use in Turkey. The excavated hole with RBM is more stable than other methods and has better air flow, making it ideal for ventilation shafts. This paper is a summary of the performance of a RBM in the Balya PB-Zn Mine in Turkey. Length and diameter of the ventilation shaft are 200 m and 2.4 m, respectively. The geological and geotechnical characteristics of the strata excavated in the mine are first given and later the validity of a model developed to predict the machine performance is discussed. It is believed that the results of this study and the model given to estimate the performance of the RBM will be useful guide for future applications. INTRODUCTION Raise boring technology was developed to meet the demands of the mining industry, but has also found numerous applications in tunneling or infrastructure projects for ventilation purposes. Raise boring machine uses a small diameter drill rod, around 230-350 mm to drill a pilot hole down to the required depth up to around 2000 m. Once the pilot hole has been drilled to the desired depth, a reamer of up to 9 m diameter is attached to the drill rod. The reamer is then pulled back up to the upper level, creating a round shape. Continues operation provides a faster advance rate than other methods. RBMs are suitable both in hard and soft rock. The flexibility in different angles and diameters is a great advantage compared to drill and blast excavation method. RBM creates a shaft with smooth walls which usually does not require lining. The hole is more stable than a drilled and blasted method and has better air flow, making it ideal for ventilation shafts. Raise boring is convenient method in competent rock; however several problems are faced in geological formations where geological discontinuities are dominant. Moreover, assembly and disassembly time may be long in some cases. The performance and operational parameters of the excavating machine should be predicted prior to starting the excavation operations in order to fulfill the economic requirements of the project. In the light of this fact, the main objective of this investigation is to summarize a case study on raise boring machine performance and suggest a new model based on laboratory test results. First, general description of the mine and project are provided. Then, the physical and mechanical characteristics of the samples taken from project area are discussed. In the third section, performance and operational parameters of RBM are investigated to understand the machine behavior in different rock characteristics and also to collect a useful database for further investigation. In the fourth section, a new model for performance estimation of RBM are recommended."

Jan 1, 2016

By U. Atici, R. Comakli

"Understanding rock properties is of vital importance in mining and civil engineering. Rock properties are generally determined through laboratory tests, which require a large number of uniformly shaped samples and technicians who use indirect methods to determine rock properties. The texture coefficient (TC), which represents various textural parameters including the size, shape, orientation, and relative proportions of grains and the matrix, is an efficient means for indirectly evaluating the mechanical behaviour of rocks. In this study, 12 different rocks (ten granites, one diorite, and one gabbro) were collected and their engineering properties. including specific gravity, porosity, P- and S-wave velocities, Schmidt rebound hardness, uniaxial compressive strength, and elasticity modulus, were investigated. Relationships between TC and these measured properties were assessed. Statistically significant (at the 95% confidence level) correlations were found between the TC and compressive strength, elasticity modulus, sound velocity (both compression and shear waves for dry and saturated samples), but no significant correlation was found with Schmidt rebound hardness. The results suggest that it is possible to use the relationships between TC and the mechanical properties of rocks in rock classification. IntroductionIn every aspect of rock engineering, knowing rock properties is essential for determining and predicting the behaviour of rocks and rock masses. Mechanical properties of rocks are important parameters in mining, geology, and engineering, and they are affected by textural characteristics such as grain size, grain shape, cement type, degree of cementation, mineral content, and the ratio of the grain area to the matrix area. The effects of textural properties on the physical and mechanical properties of rocks have been investigated for a long time, and previous studies revealed close relationships between single parameters related to rock texture and mechanical properties of rocks (Akesson et al. 2001; Gunsallus and Kulhawy 1984; Merriam, Rieke, and Kim, 1970: Onodera and Kumara 1980; Prikryl 2006; Ulusay, Tureli, and Bider, 1994; Tugrul and Zarif 1998). Rock properties are usually determined using mechanical tests, which require uniformly shaped and relatively large samples. However, it is not always possible to obtain such samples. Furthermore, rocks with similar textural and structural properties may exhibit different mechanical behaviour. Howarth and Rowlands (1987) developed a texture coefficient (TC) that expresses all the main textural parameters of a rock in a single dimensionless quantity based primarily on statistical assessment. The TC makes it possible to understand the effects of a rock’s textural properties on its mechanical properties using thin sections instead of large, uniform samples. Ersoy and Waller (1995) investigated the relationship between strength and TC for limestone, sandstone, and siltstone; they also examined the effect of rock properties and TC on drilling performance. Ozturk, Nasuf, and Bilgin (2004) explored the relationship between rock quality and TC by evaluating the uniaxial compressive strength (UCS) values of limestone, basaltic andesite, and tuff. Gupta and Sharma (2012) evaluated TCs as well as the petrophysical and mechanical properties of quartzite from the lower and higher Himalayas and found a strong relationship between TC and UCS. Similarly, Ozcelik, Bayram, and Yasitli (2013) investigated the relationship between TC and various parameters in marble by applying the statistical analyses developed by Ozturk, Nasuf, and Kahraman (2014)."

Jan 1, 2019

By B. (Mamas) Das

A project to evaluate the suitability of point Load strength tests for testing and classifying coal measure rocks for coal mining application was initiated by Canada Centre for Mineral and Energy Technology (CANMET). A summary of this study with emphasis on the important findings is presented in this paper. The instrument as used in this study is a Robertson Research Rock Strength Index Log. Because of the variation in the correlation ratio between uniaxial compressive strength and point Load strength index for hard rocks and soft rocks it was decided to establish this corre¬lation initially on cement concrete specimens specially prepared for this purpose following ASTM specifications. These specimens are expected to represent soft rocks and at the same time would be of uniform quality. Once a general trend of this correlation was established tests were performed on coal and rock samples from the sub-bituminous and bituminous coalfields in Canada. The most important results may be stated as follows: (i) Generally, the common value of the ratio between the uniaxial compressive strength and the point load strength index ranges between 8 to L4. (ii) The Robertson Research Rock Strength Index Log proves to be quite suitable for testing sandstone, siltstone and some coals from the bituminous coalfields but problems have been experienced when testing weathered samples or samples from the sub-bituminous coalfields. (iii) In some cases tests were successful if Larger samples from weathered zones or from sub-bituminous coalfields were used. However, a magnified load gauge for 0-3KN or 0-5KN is expected to be the best solution for soft and weathered rocks in most of the cases. Some mudstones and some rocks from weathered zone do not appear to be suitable for these tests. This aspect of the study is still under investigation. (iv) Deterioration of rock properties due to weathering has been determined through tests on samples collected from weathered and unweathered samples.

Jan 1, 1984

By L. M. Petrie, D. C. Marozas, S. E. Paulson

The US Bureau of Mines (Bureau) is conducting research to evaluate the potential for developing an in situ leach mining process that will selectively extract manganese from oxide ores, leaving gangue relatively undisturbed. To accomplish this, a geochemical approach based on deposit-specific information, such as mineralogy and geology, is used to constrain the operating parameters of the system. Among the studies being conducted are: • leaching experiments to define reaction mechanisms and kinetics, • detailed petrologic characterization at the microscopic scale to assess manganese distribution and leaching efficiencies, • deposit characterization and evaluation, and • development of potential manganese recovery schemes. Data from these studies are being used to develop engineering design information for an in situ mining process. Specific details of the Bureau's research project are discussed, including results obtained to date.

Jan 1, 1993

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines, are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. Comparative testing of these drill types was performed in Quebec. Based on the test results and on time studies performed in the mines, water-powered drilling was reviewed. The review considered the drilling rates achieved, the infrastructure needed, side effects and health and safety considerations. This study shows that the application of water-powered drills may, under specific conditions, help increase the footage drilled and may improve the working environment. Examples of such applications are presented in the conclusions.

Jan 1, 1997

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. A comparative testing of both drill types was performed in Quebec. Based on its results and time studies done in the mines, water-powered drilling has been reviewed with regards to drilling rates achieved, infrastructure needed, side effects, health and safety considerations. This study shows that the application of water-powered drills may help increase footage drilled and improve working environment, but under specific conditions. The examples of such applications are given in the conclusions.

Jan 1, 1995

By T. F. Oliveira, E. B. Zanelato, J. Alexandre, L. J. T. Petrucci, A. R. G. Azevedo

The paper and cellulose industry is responsible for generating large amounts of solid waste, which are produced during various stages of the production process. Currently this material goes to places like landfills and other generating costs for the company. Furthermore, cement, mortar and concrete represent a significant economic and environmental cost. This study aims to determine the pozzolanic activity index in the residue studied to verify its viability in the incorporation of the same in cement. It will be used Luxan method for this determination. The data found show that the material has the possibility of being incorporated in the mortar due to its pozzolanic activity index.

Mar 1, 2017

By Janaina Gonçalves Maria da Silva Machado, Carlos Mateus Braga de Almeidar, Leandro Miranda Nascimento

Knowing the reduction of the concentration of iron in the mineral load extracted in the last decades and, therefore, greater need for comminution processes, there is no denying that iron ores tend to get increasingly thin for steelmakers. In Reactors such as Blast Furnace and others of fusion-reduction, where the reduction of the iron ore for the metallic iron for the steel production occurs, we observed that one of the alternatives is to agglomerate the raw materials in the form of briquettes, improving the kinetics of the chemical reactions, since ores in the form of fines impair factors such as the permeability required for reduction. These agglomerates are composed of a reducer, fines of ferrous materials and a binder material, and require, in addition to satisfactory Metallization, mechanical resistance, avoiding losses when the compound is fragmented during transport or during its deposition in the Steel Reactor. In the following work, Briquettes were produced with Charcoal, Pellet Feed, Molasses Cane and Hydrated Lime. The mixtures were pressed under different conditions of Pressure (1, 2 and 3 tons-force), and pressing time (20 , 60 and 100 seconds), aiming to analyze the influence of these two variables on the drop tests, mechanical resistance of the briquettes generated.

Oct 1, 2019

By S. N. Monteiro, J. Alexandre, L. G. Pedroti, D. P. Santos, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

The glass cutting industry is responsible for generating large quantities of waste, during the stages of cutting and polishing. The disposal of this material generates a cost to the company, thus looking for ways to repackage it, so there is the possibility of incorporating it into the adhesive mortar. The objective of this work is the characterization of waste and assessment of the properties of these mortars, fresh, and check the possibility of their use. As for the characterization, were carried out particle size testing, density and pozzolanic activity, for the fresh state were performed tests of air content, water retention consistency and entrained particular index. Were incorporated 0,10, 15 and 20% of the amount of sand. The results showed that the material on display ha spotential for use in adhesive mortar, with values within the limits stipulated by Brazilian standards.

Mar 1, 2017

By Afonso Garcez de Azevedo, Anna Carolina Lopes Rabello, Renan Tavares Vicente, Sergio Neves Monteiro, Amanda Maia Ferreira dos Santos

Civil construction is a sector of extreme impact in the Brazilian economy, with construction and demolition waste (RCD) having an extreme impact on the amount of urban solid waste. In this research it was proposed to propose a way of using these residues in the construction of concrete artifacts for structural use. Concrete specimens with sand substitution by RCD were produced in different percentages as a way to contribute to reduce,recycle and reuse thi large amount of waste from the construction industry. The objective of this work was to study the mechanical properties of structural concrete with total and partial replacement (25, 50, 75 and 100%) in sand mass. The results of the compression test indicate good quality for concretes with mass substitution of up to 75% per RCD.

Mar 1, 2018